Text preview for : 32HDT20.pdf part of Hitachi 32HDT20M Hitachi Plasma Display Panel
Models: 32HDT20M, 42HDT20M, AVC20
Chassis: PT2-E, PT2-G, AVC1-U
Service Manual
Back to : Hitachi_Plasma_32HDT20.pa | Home
PA
SERVICE MANUAL
NTSC P T 2 E / G AV C 1 - U Chassis
CONTENTS
No. 0159
32HDT20M: PT2-E Chassis 42HDT20M: PT2-G Chassis AVC20: AVC1-U Chassis
R/C: CLU-5723TSI
TO GO TO A CHAPTER, CLICK ON ITS HEADING BELOW
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PRODUCT SAFETY NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 SERVICING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 AGENCY REGULATORY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 ACKNOWLEDGMENTS AND TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 BASIC SETUP & OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 TROUBLESHOOTING FLOWCHARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 WAVEFORMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 DC VOLTAGE TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 CIRCUIT SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 PRINTED CIRCUIT BOARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 BLOCK DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 CONNECTION DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 EXPLODED VIEW DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
CAUTION:
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Before servicing this chassis, it is important that the service technician read the "IMPORTANT SAFETY INSTRUCTIONS" in this service manual.
SAFETY NOTICE USE ISOLATION TRANSFORMER WHEN SERVICING Components having special safety characteristics are identified by a ! on the schematics and on the parts list in this Service Data and its supplements and bulletins. Before servicing the chassis, it is important that the service technician read and follow the "Important Safety Instructions" in this Service Manual.
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
PLASMA DISPLAY PANEL
MAY 2002 HHEA-MANUFACTURING DIVISION
PT2-E/G AVC1-U
SAFETY PRECAUTIONS
NOTICE: Comply with all cautions and safety-related notes located on or inside the cover case and on the chassis or plasma module. WARNING: Since the chassis of the AVC unit and Plasma Panel unit is connected to both sides of the AC power supply during operation, whenever the receiver is plugged in, service should not be attempted by anyone unfamiliar with the precautions necessary when working on this type of receiver. 1. When service is required, an isolation transformer should be inserted between power line and the receiver before any service is performed on a "HOT" chassis receiver. 2. When replacing a chassis in the receiver, all the protective devices must be put back in place, such as barriers, nonmetallic knobs, insulating cover-shields, and isolation resistors, capacitors, etc. 3. When service is required, observe the original lead dress. 4. Always use manufacturer's replacement components. Critical components as indicated on the circuit diagram should not be replaced by another manufacturer's. Furthermore, where a short circuit has occurred, replace those components that indicate evidence of over heating. 5. Before returning a serviced receiver to the customer, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without danger of electrical shock, and be sure that no protective device built into the receiver by the manufacturer has become defective, or inadvertently defeated during servicing. Therefore, the following checks should be performed for the continued protection of the customer and service technician. Leakage Current Cold Check With the AC plug removed from the 120V AC 60Hz source, place a jumper across Line 1 and Line 2 of the three plug prongs, do not connect with the third prong, which is physical ground. Using an insulation tester (DC500V), connect one of its leads to the AC plug jumper and touch with the other lead each exposed metal part (antennas, screwheads, metal overlays, control shafts, etc.), particularly any exposed metal part having a return path to the chassis shoud have a minimum resistor reading of 4M and a maximum resistor reading of 7.14M. Any resistance value below or above this range indicates an abnormality which requires corrective action. An exposed metal part not having a return path to the chassis will indicate an open circuit. Leakage Current Hot Check This check must be done considering the AVC or the PDP monitor as one instrument each. With any of the instruments completely reassembled (being the instrument either the AVC center or the PDP monitor), plug the AC line cord directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with the American National Standards Institute (ANSI) C101.0 Leakage Current for Appliances. In the case of the PDP monitor set the AC switch first in the ON position and then in the OFF position, measure from a known earth ground (metal waterpipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle bracket, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milliamps. Reverse the instrument power cord plug in the outlet and repeat test.
DEVICE UNDER TEST
(READING SHOULD NOT LEAKAGE BE ABOVE 0.5mA) CURRENT TESTER
TEST ALL EXPOSED METAL SURFACES 3-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUS AS REQUIRED) EARTH GROUND
AC LEAKAGE TEST ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE RECEIVER TO THE CUSTOMER.
2
PT2-E/G AVC1-U
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in HITACHI television receivers have special safety-related characteristics. These are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified with a ! 11mark in the schematics and parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the HITACHIrecommended replacement component, shown in the parts list in this Service Manual, may create shock, fire, X-radiation, or other hazards. Product safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current HITACHI Service Manual. A subscription to, or additional copies of HITACHI Service Manuals may be obtained at a nominal charge from HITACHI Sales Corporation. AVC20 - Audio Video Control Unit 1. Follow the general caution recommendations from "Safety precautions" section. 32/42HDT20M - Plasma Monitor Unit 1. Follow the general caution recommendations from "Safety precautions" section. 2. Since the Panel module and front filter are made of glass, sufficient care shall be taken when handling the broken module and filter in order to avoid injury. 3. If necessary to replace Panel module, this work must be started after the panel module and the AC/DC Power supply becomes sufficiently cool. 4. Special care must be taken with the display area to avoid damaging its surface. 5. The Panel Module shall not be touched with bare hands to protect its surface from stains. 6. It is recommended to use clean soft gloves during the replacing work of the Panel module in order to protect, not only the display area of the panel module but also the serviceman. 7. The Chip Tube of the panel module (located upper left of the back of the panel module) and flexible cables connecting Panel glasses to the drive circuitry Printed Wiring Boards (P.W.B.) are very weak, so sufficient care must be taken to prevent breaking or cutting any of these. If the Chip Tube breaks the panel module will never work, replacement for a new plasma panel module will be needed. 8. Signal, power supply P.W.B.'s and PDP driving circuits P.W.B.'s are assembled on the rear side of the PDP module, take special care with this fragile circuitry; particularly, Flexible Printed Circuits bonded to surrounding edges of the glass panel. They are not strong enough to withstand harsh outer mechanical forces. Avoid touching the flexible printed circuits by not only your hands, but also tools, chassis, or any other object. Extreme bending of the connectors must be avoided too. In case the flexible printed circuits are damaged, the corresponding addressed portions of the screen will not be lit and exchange of a glass panel will be required. PDP Module Handling When there is need to replace a broken PDP module which is the displaying device from the Plasma monitor unit, consider the following: 1. When carrying the PDP module, two persons should stand at both shorter-edge sides of the glass-panel and transport it with their palms. Avoid touching the Flexible Printed Circuits or the chip tube on the corner of the glass-panel. Handle only by the surface of the glass panel. In case of some PDP modules, electrode repair is done by connecting between regular terminal with Cu tape and Cu wire. Please do not hook and/or damage this repair line. If it is damaged, the module will not function unless the glass-panel is exchanged with a new glass-panel. 2. When carrying PDP module, watch surrounding objects, such as tables, and also do not carry it alone sice it may be dangerous and it will be damaged due to excessive stress to the module (glass-panel). 3. Please do not stand the codule with the edge of the glasspanel on the table since this might result in damage to the glass-panel and/or flexible printed circuits due to excessive stress to the module (glass-panel). WARNING Lead in solder used in this product is listed by the California Health and Welfare agency as a known reproductive toxicant which may cause birth defects or other reproductive harm (California Health and Safety Code, Section 25249.5). When servicing or handling circuit boards and other components which contain lead in solder, avoid unprotected skin contact with solder. Also, when soldering make sure you are in a well ventilated area in order to avoid inhalation of any smoke or fumes released. SAFETY NOTICE USE ISOLATION TRANSFORMER WHEN SERVICING POWER SOURCE This television receiver is designed to operate on 120 Volts/60Hz, AC house current. Insert the power cord into a 120 Volts/60Hz outlet. NEVER CONNECT THE TV TO OTHER THAN THE SPECIFIED VOLTAGE OR TO DIRECT CURRENT.
3
PT2-E/G AVC1-U
SERVICING PRECAUTIONS
CAUTION: Before servicing instruments covered by this service data and its supplements and addenda, read and follow the "Important Safety Instructions" on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Guidelines 1. Always unplug the instrument AC power cord from the AC power source before: a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly. b. Disconnecting or reconnecting any instrument electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. 2. Do not spray chemicals on or near this instrument or any of its assemblies. 3. Unless specified otherwise in these service data, clean electrical contacts by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive applicator: 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%99% strength). CAUTION: This is a flammable mixture. Unless specified otherwise in these service data, lubrication of contacts is not required. 4. Do not defeat any plug/socket of voltage interlocks with which instruments covered by this service data might be equipped. 5. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heatsinks are correctly installed. 6. Always connect the test instrument ground lead to the appropriate instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last. 7. Use with this instrument only the test fixtures specified in this service data. CAUTION: Do not connect the test fixture ground strap to any heatsink in this instrument. Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some fieldeffect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or desolder ES devices. 4. Use only can anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ES device. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.) 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)
4
PT2-E/G AVC1-U
General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range 500°F to 600°F. 2. Use an appropriate gauge of resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well-tinned. 4. Thoroughly clean the surfaces to be soldered. Use a small wire-bristle (0.5 inch or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following desoldering technique. a. Allow the soldering iron tip to reach normal temperature (500°F to 600°F). b. Heat the component lead until the solder melts. Quickly draw away the melted solder with an anti-static, suction-type solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach normal temperature (500°F to 600°F). b. First, hold the soldering iron tip and solder strand against the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil or components. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to areas.) "Small-signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect to replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact, then solder each connection. Power Output Transistor Devices Removal/Replacements 1. Heat and remove all solder from around the transistor leads. 2. Remove the heatsink mounting screw (if so equipped). 3. Carefully remove the transistor from the circuit board. 4. Insert new transistor in circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heatsink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicularly to the circuit board.
Use Soldering Iron to Pry Leads
Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suctiontype solder removal device (or with solder braid) before removing the IC.
3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original leads". If they are not shiny, reheat them and, if necessary, apply additional solder.
IC Removal/Replacement Some Hitachi unitized chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.
5
PT2-E/G AVC1-U
Fuses and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of circuit board hollow stake. 2. Securely crimp leads of replacement component around stake 1/8 inch from top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board, to prevent excessive component temperatures. Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board, causing the foil to separate from, or "lift-off," the board. The following guidelines and procedures should be followed whenever this condition is encountered. In Critical Copper Pattern Areas High component/copper pattern density and/or special voltage/current characteristics make the spacing and integrity of copper pattern in some circuit board areas more critical than in others. The circuit foil in these areas is designated as Critical Copper Pattern. Because Critical Copper Pattern requires special soldering techniques to ensure the maintenance of reliability and safety standards, contact your Hitachi personnel. At IC Connections To repair defective copper pattern at IC connections, use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections.) 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary.) 2. Carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. At Other Connections Use the following technique to repair defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.
DEFECTIVE COPPER REMOVED
Insulated Jumper Wire 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both wire sides of the pattern break and locate the nearest component directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so that it does not touch components or sharp edges.
BARE JUMPER WIRE
CRIMP AND SOLDER
Install Jumper Wire and Solder
3. Bend a small "U" in one end of a small-gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the cut-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area, and clip off any excess jumper wire.
6
PT2-E/G AVC1-U NOTE: These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose.
Leadless Chip Components (surface mount)
Chip components must be replaced with identical chips due to critical foil track spacing. There are no holes in the board to mount standard transistors or diodes. Some chip capacitor or resistor board solder pads may have holes through the board, however the hole diameter limits standard resistor replacement to 1/8 watt. Standard capacitors may also be limited for the same reason. It is recommended that identical chip components be used. . Chip resistors have a three digit numerical resistance code -1st and 2nd significant digits and a multiplier. Example: 162 = 1600 or 1.6K resistor, 0 = 0 (jumper). Chip capacitors generally do not have the value indicated on the capacitor. The color of the component indicates the general range of the capacitance. Chip transistors are identified by a two letter code. The first letter indicates the type and the second letter, the grade of transistor. Chip diodes have a two letter identification code as per the code chart and are a dual diode pack with either common anode or common cathode. Check the parts list for correct diode number.
How to Replace Flat-lC --Required Tools--
· Soldering iron · iron wire or small awl · De-solder braids · Magnifier 1. Remove the solder from all of the pins of a Flat-lC by using a de-solder braid.
Flat-IC De-Solder Braid Soldering Iron
2. Put the iron wire under the pins of the Flat-lC and pull it in the direction indicated while heating the pins using a soldering iron. A small awl can be used instead of the iron wire.
Iron Wire Awl
Pull
Soldering Iron
Soldering Iron
Component Removal
1. Use solder wick to remove solder from component end caps or terminals. 2. Without pulling up, carefully twist the component with tweezers to break the adhesive. 3. Do not reuse removed leadless or chip components since they are subject to stress fracture during removal .
3. Remove the solder from all of the pads of the Fiat-lC by using Soldering a de-solder braid.
Iron De-Solder Braid Flat-IC
Chip Component Installation
1. Put a small amount of solder on the board soldering pads. 2. Hold the chip component against the soldering pads with tweezers or with a miniature alligator clip and apply heat to the pad area with a 30 watt iron until solder flows. Do not apply heat for more than 3 seconds Chip Components
TYPE
4. Position the new Flat-lC in place (apply the pins of the Flat-lC to the soldering pads where the pins need to be soldered). Properly Polarity Symbol determine the positions of the soldering pads and pins by correctly aligning the polarity symbol. 5. Solder all pins to the soldering pads using a fine tipped soldering iron.
C
GRADE
SOLDER CAPS
B E
Solder
TRANSISTOR CAPACITOR 1ST DIGIT COMMON CATHODE 2ND DIGIT MULTIPLIER = 1600 = 1.6K
Soldering Iron
6. Check with a magnifier for solder bridge between the pins or for dry joint between pins and soldering pads. To remove a solder bridge, use a de-solder braid as shown in the figure below.
De-Solder Braid Bridge Solder Soldering Iron
ANODES MH DIODE
SOLDER CAPS RESISTOR
7
PT2-E/G AVC1-U
AGENCY REGULATORY INFORMATION
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi Home Electronics (America), Inc. may void the user's warranty.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Any cables that are supplied with the system must be replaced with identical cables in order to assure compliance with FCC rules. Order Hitachi spares as replacement cables.
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding this declaration, contact: Hitachi America, LTD. Home Electronics Division 1855 Dornoch Court San Diego, CA 92154 Tel. 1-800-448-2244 (1-800-HITACHI) ATTN: CUSTOMER RELATIONS
8
PT2-E/G AVC1-U
ACKNOWLEDGMENTS AND TRADEMARKS
This Plasma Television complies with VESA DDC2B specifications, Plug & Play is a system with computer, peripherals (including monitors) and operating system. It works when the monitor is connected to a DDC ready computer that is running an operating system software that is capable for the plug & play. When a Plug and Play PC is powered on, it sends a command to the Monitor requesting identification. The Monitor sends back a string of data including its characteristics.
TRADEMARK ACKNOWLEDGMENT
DDCTM is a trademark of Video Electronics Standard Association. IBM PC/AT and VGA are registered trademarkds of International Business Machines Corporation of the U.S.A. Apple and Macintosh are registered trademarks of Apple Computer, Inc. VESA is a trademark of a nonprofit organization, Video Electronics Standard Association.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.
Notes on Closed Caption: This Plasma Television receiver will display television closed captioning, ( paragraph 15.119 of the FCC rules.
or
), in accordance with
TruBass and the SRS from SRS Labs, Inc.
®
symbol are trademarks of SRS Labs, Inc. TruBass technology is incorporated under license
9
PT2-E/G AVC1-U INTRODUCTION
The 32/42HDT20 is a Plasma Television set; it is constituted by the combination of two main parts, an AUDIO VIDEO CONTROL Center, and the Plasma Display monitor. Each part has a model name and a chassis name:
Part Audio Video Control Center 32" Plasma Display Monitor 42" Plasma Display Monitor
Model Name AVC20 32HDT20M 42HDT20M
Chassis Name AVC1-U PT2-E PT2-G
The AVC center is a box that controls most of the user functions of the complete TV set and conditions the signal before it arrives to the monitors. The monitors, 32" and 42", contain the displaying device, which is the plasma display panel module, and the driving circuitry, which receives the signal from the AVC center and after processing, delivers the image to the display module. This HITACHI Service Manual is intended for the qualified service personnel and it contains the necessary information for troubleshooting the Plasma television set in case of malfunction. DIMENSIONS: 32HDT20M
42HDT20M
Stand
Speakers
AVC20
Stand
Speakers
POWER RATINGS:
No. 1 2 3
Model Name 32HDT20M 42HDT20M AVC20
Indicated Value Max Rating Average Rating (W) (W) (A) 230 2.2 152 350 3.5 217 35 .75 35
PST(W) (W) 0.9 1.1 2.7
Chassis PT2-E PT2-G AVC1-U
CIRCUIT PROTECTION
CAUTION: Example: Below is an EXAMPLE only. See Replacement Parts List for details. The following symbol near the fuse indicates fast operation fuse (to be replaced). Fuse ratings appear within the symbol.
F 6 A 125V
125V 6A
"RISK OF FIRE - REPLACE FUSE AS MARKED" 10
The rating of fuse F901 is 6A - 125V. Replace with the same type fuse for continued protection against fire.
PT2-E/G AVC1-U
PDP MONITOR SPECIFICATIONS Item Destination Exterior Model Name Cabinet Dimensions: (Main Body) (Speaker & stand included) Cabinet Color Stand Weight (Main Body) (Speaker & Stand included) (Main Body:Packed) Screen Size Resolution Dot Pitch (H) Dot Pitch (V) Viewing Angle (H) Viewing Angle (V) Surface Finishing Peak Brightness (4% window) 32HDT20M U.S.A. / CANADA 974x501x90mm 974x578x256mm Metallic Silver Included 23.1 kg typ. 26.2 kg typ. 33.0 kg typ. (Packed) 715.68x399.39mm (32": 16x9) 852x1024 pixels 0.84mm 0.39mm ±80° ±80° AR Coating, Mesh Over 200 cd/m2 (When VIDEO, Sports, Color temperature `HIGH' Input Signal Amplitude 120% is set) Over 190 cd/m2 (When RGB is set) Over 45 cd/m2 500:1 (typ.) Over 16.7 million colors 7w + 7w (6) PUSH (LOCK) 1 Switch PUSH (NON-LOCK) 1 Switch 24 pin DVI connector 1 system 8 pin Mini DIN connector 1 Sub Woofer Output 1 system One system each for L and R 3 Polarity Receptacle Single Phase AC108~132V,60Hz 5°C~35°C (41°F~95°F) -15°C~60°C(5°F~140°F) 20~80%RH (Non-condensing) 20~90%RH (Non-condensing) 800 to 1114hPa (altitude: 1888m to -757m, 6194' to -2484') 300 to 1114hPa (altitude: 9727m to -757m, 15,510' to -2484') 1030x636x89mm 1233x713x300mm 42HDT20M
29.8 kg typ. 38.8 kg typ. 43 kg typ. (Packed) 922x522mm (42": 16x9) 1024x1024 pixels 0.90mm 0.51mm
Display Panel
Front Filter Brightness
Contrast Color Reproduction Audio Output Panel Operation Input Terminal Output Terminal Power Supply Source Guaranteed Environment Condition
All White Pattern Contrast ratio Color Reproduction Audio Output Main Power Switch Sub Power Switch Video/Audio Input Audio Line Output Speaker Output Connector Input Voltage Temp. (Operating) Temperature (Stored) Humidity (Operating) Humidity (Stored) Atmospheric Pressure (Operating) Atmospheric Pressure (Stored)
Over 190 cd/m2 (When VIDEO, Sports, Color termperature `HIGH' Input Signal Amplitude 120% is set) (Over 210 cd/m2 (When RGB is set) Over 45 cd/m2 700:1 (typ.)
9w + 9w (6)
11
PT2-E/G AVC1-U
AVC SPECIFICATIONS (1 of 2) MODEL Dimensions Size Weight A/C Input Voltage Input AC voltage 1 2 3 AVC20 430mm x 121mm x 280mm 4.0kg AC108V~132V (With 3 plug AC Power Cord inlet type, 1.8m legth) 60Hz 35W, Standby 2.7W ENGE6106D/ENG36614G 2~13 14~69 A-5~A-1,A~W,W+1~W+84 NTSC 480i/p, 1080i, 720p VGA~SXGA (fH:24KHz-80KHz, fV:50Hz-75Hz) 3D Y/C (ON fix) No Motion Adaptive Interpolation News, Movie, Music, Sports 1024i 1024i 1024i 1024i TruBass (High, Medium, Low, Off) Matrix Surround (On, Off) Picture, Contrast, Brightness, Color Tint, Sharpness, W/B Temp. Contrast, Brightness, W/B Temp., Enhancer Hor./Vert./Raster Position, Dot Clock Frequency/Phase Vol., Balance, Bass, Treble, Mute For all video signal combinations, except PC Signal With (Component Input is used only for Main Picture) 5 Modes (Only NTSC, 480i, 480p) 4:3 Standard/16:9 Standard/ 4:3 Expanded/Zoom1/Zoom2 Full/Normal/Real (Real only in VGA mode) With (only Movie Mode) 3 Modes (High, Medium, Standard) RGB1, RGB2, VIDEO1/2/3/4/5, ANT A/B
Front End
Input AC Frequency Power Consumption Front End Available Channel
Input Signal
Video Signal Component Signal PC Signal Y/C Separation Line Correction I-P Conversion Picture Mode Display Mode
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
VHF UHF CATV
Picture
Video Signal Component Signal PinP Mode PC Signal
Sound Enhancement Adjustment
Settings for Video Signal Settings for PC Signal Settings for PC Raster Settings for Sound Split PinP Surf PinP Wide Mode Aspect Selection
General Function
Video PC
Film Theater Color Temperature Input Signal Selection
12
PT2-E/G AVC1-U
AVC SPECIFICATIONS (2 of 2) MODEL General Function Gamma Correction Picture Enhancer Input Signal Identification Audio Special Mode Power Save Mode 34 35 36 37 38 39 Burning Protection 40 OSD Language VIDEO/PC 41 42 PC Input (RGB) 43 Composite Video Input (Video2~5) 44 S-In (S2 Terminal)(Video/5 are 45 common selected, S-In is priority) Component Signal Input 46 (Video1, Video2) Audio In (L/R) (Lch:mono) 47 CATV In U/V Ant Input Video Monitor Out Terminal Audio Output Terminal Audio Monitor Out Terminal IR-OUTPUT Headphone Terminal PDP Interface Terminal Main Power Switch Power On/Off Switch IR Receving Unit Power Indicator LED Menu Control Key 48 49 50 51 52 53 54 55 56 57 58 59 60 AVC20 Only for Service Menu With (only RGB1/2) Yes No With With (On/Off) With (Raster Shift on all/White Pattern) English, French, Spanish/English CLU-5723TSI 2 Inputs mini Dsub-15PX1, DVI-DX1 4 Input RCA pin x4 (1 Input Front Panel) 3 Input; mini Din-4Px3 (1 S-In on Front Panel) 2 Input; RCA pin x 6 (Y of Video 2 is common input for Composite in) 7 Input; RCA pin x 14 RGB: 2 Input, Video 5 Input 1 Input (VIDEO2 Link) Ant A In, Ant B In, To Conv. 1 Output: RCA pin x1 1 Output L/R; RCA pin x 2 1 Output L/R; RCA pin x 2 2 Terminal 1 Terminal (only for AVC) DVI-D(26p) + 8PIN-DIN No With (link to PDP) With (link to PDP) With With (Ch U/D, Vol U/D, A/V Input Select, Menu Select)
PC In Video In
R/C Handset In/Out Terminal
ALPS
Front Key
13
BASIC SETUP & OPERATION
VIEWING The major benefit of the HITACHI Plasma Television is its large viewing screen. To see this large screen at its best, test various locations in the room to find the optimum spot for viewing. The best picture is seen by sitting directly in front of the TV and about 8 to 18 feet from the screen. During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room. If the TV's audio output will be connected to a Hi-Fi system's external speakers, the best audio performance will be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.
IMPORTANT NOTES
PT2-E/G AVC1-U
20 3' 0' 5' 10'
BEST VERTICAL VIEWING ANGLE
15'
20'
R 4" Minimum 50
S BEST HORIZONTAL 10' 50 15' 20'
5' 4" Minimum L
VIEWING ANGLE
S
No. Items Notes 1 Arching sound from A buzzing sound might be heard when the plasma display monitor is turned on in a very quiet plasma display monitor's room. This is due to the plasma panel drive circuit when it is functioning. This arching sound panel. is normal and it is not a malfunction. 2 3 Interference for infrared equipment. Bright and dark spots Some infrared rays are emitted from the plasma display monitor's panel that might affect other infrared controlling equipment. High-precision technology is used to manufacture the plasma display panel; But in some cases, there are minor defects in some parts of the screen. Points that do not light, points with brightness different from that of the periphery, points with color different from that of the periphery, etc. Some pixels will always be on or always off. Please note that this is not a malfunction.
4 5
Picture Image (Spectrum) When receving still picture signals, (e.g. channel number indication or clock indication) for a while, you can see image-like when the picture varied. This is not a defect. Display panel surface temperature is too high The plasma display panel is lighting the phosphors by the discharge of internal radiation. In some cases, this may cause the temperature of the panel surface to increase. Please note that this is not a malfunction. The Plasma TV surface temperature is higher than a Cathode-ray-tube. The plasma panel is made from glass. Heavy shock on the front panel might damage it. When the PDP monitor is transported horizontally, the glass panel has the possibility of being broken or increasing the picture defects. At the time of transportation, horizontal style is prohibited. More-over, please treat the plasma panel with great care because of a precision apparatus. Please instruct transporters so that it should be put into the packing box at the time of shipment.(There is a possibility that breakage of the panel or defects will increase.) Rough transportation might cause damage to the panel and pixel failure. The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images. Tips to prevent such image retention are: - Do not display images having sharp brightness differences or hi-contrast images, such as monochrome characters and graphic patterns, for long. - Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen saver function. - Turn down the contrast and brightness controls.
6 7
Plasma Surface Transportation
8
Image retention
9
Luminosity and contrast
PDP television has luminosity and low contrast compared with CRT television. When a screen is seen at point-blank range, a random fine grain may be visible to a dark part. If an apparatus (VCR, etc.) antenna line is arranged near the monitor, the image may shake, or disturbance may be received. There is some time lag betweeen the picture and the sound. You can see lip motion that is delayed compared to the sound. Electric discharge/luminescence characteristic of the PDP panel also changes with peripheral temperature. Moreover, since there is also high power consumption value, a specified temperature environment is required. Storing the plasma television for a period of more than 2 to 3 months without use might cause an unstable picture when the set is turned on. Operating altitude: 800 to 1114hPa (6194ft to -2484ft). Operating temperature: 41°F to 95°F. Storage Altitude: 300 to 1114hPa (15510ft to -2484ft). Storage temperature: 5°F to 140°F.
10 Granular spots 11 Disturnbance to video apparatus 12 Lip Sync 13 About the use environment of PDP television (temperature) 14 Caution on prolonged storage 15 Operating 16 Storage
14
PT2-E/G AVC1-U
To take measures to prevent the Plasma Display from tipping over and prevent possible injury it is important to mount the unit in a stable place. Securing to a table-top 1. Using wood screws (two) fasten the set to the clamping screw holes on the rear of the Plasma Display stand as shown below. 2. Using commercially available wood screws, secure the set firmly in position.
Wood screw two places
32HDT20
Rear View
42HDT20
Securing to a wall 1. Keep the Plasma Display monitor four inches away from the wall except those hung to the wall mount bracket. 10cm (4 inches) or more
NOTES:
or defect. 2. The plasma television has two AC cords, one on the AVC center and the other on the Plasma Display monitor. In case of an abnormal symptom, unplug both AC cords. 3. If you purchased the wall mount bracket option, please ask for professional installer. Do not install by yourself.
1. Do not block the ventilation holes of the Plasma Display monitor or the AVC center. Blocking the ventillation holes might cause fire
Caution when moving the main unit As this product is heavy, whenever it is moved, two people are required to transport it safely. Whenever the unit is moved it should be lifted forward using the two handgrips at the back, and the unit should then be held at the base on both sides for stability. When moving the Display Monitor, lift the handles and the bottom frame as shown below. Do not grab the speakers or the back cover when lifting.
Handgrips
ANTENNA
32HDT20
42HDT20
Unless your Plasma Television is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient. LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc. 15
FRONT PANEL CONTROLS
FRONT VIEW
32HDT20 DISPLAY MONITOR 42HDT20 DISPLAY MONITOR
PT2-E/G AVC1-U
STANDBY (RED) ON (GREEN)
MAIN POWER
STANDBY (RED) ON (GREEN)
MAIN POWER
AUDIO/VIDEO CONTROL CENTER
TruBass
AUDIO/VIDEO CONTROL CENTER
POWER STANDBY (RED) ON (GREEN)
PULL
INPUT/EXIT
POWER STANDBY (RED) ON (GREEN)
VOL
PHONES
INPUT 5
MENU/SELECT
CH
S-VIDEO VIDEO
L/(MONO)
AUDIO
R
MENU/SELECT button This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode or Adjust Mode. INPUT/EXIT button Press this button to select the desired input, VIDEO 1 to 5, RGB 1/2, or Ant A/B source. Your selection is shown in the top right corner of the screen. This button also serves as the EXIT button when in MENU mode or Adjust Mode. NOTES: Your remote control does not have an INPUT button. To change to video inputs, press VID1~VID5 buttons depending on the input you wish to switch to. Press TV/RGB button on the remote control to change between the TV's RGB1, and RGB2 modes. CHANNEL selector Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down ( ) and up ( ) buttons when in MENU mode or Adjust Mode. VOLUME level Press these buttons to adjust the sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left ( ) and right ( ) buttons when in MENU mode or Adjust Mode.
16
PT2-E/G AVC1-U
POWER button Display Monitor "MAIN POWER" button This power button is for the complete system, and must be turned ON/OFF manually. It is recommended to leave the "MAIN POWER" to ON condition (lights red) for stand-by mode. AVC POWER button The AVC power can be turned ON/OFF manually or by remote control. Turning on the AVC Power will only turn on the AVC box if the "MAIN POWER" of the display monitor is off.
STANDBY (RED) ON (GREEN) MAIN POWER
POWER light indicator To turn the monitor ON, press the main power switch located on the lower right side of the monitor. A red stand-by indicator lamp located on the lower right corner of the front bezel will illuminate. The PDP is now ready for remote on/off operation.
Indicating Lamp Off Lights Red Lights Green Lights Orange (Flashing) Power Status Off Off (Stand-by) On Off (Power Saving) Operating When the main power switch is set OFF. When the main power switch on the display monitor is ON, and the AVC Center is OFF. Display monitor MAIN POWER is ON and AVC Center power is ON. Display monitor MAIN POWER is ON and and AVC Center power is ON, with no signal input except antenna (no sync. signal).
NOTE: This Power light indicator is also a service aid. (See page 19.)
REMOTE CONTROL sensor Point the remote at this area when selecting channels, adjusting volume, etc. FRONT INPUT JACKS (for VIDEO: 5) Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view a show or recording. press the VID5 button on the remote control button and VIDEO: 5 appears in the top right corner of the TV screen. If you have mono sound, insert the audio cable into the left audio jack. PHONES JACK Use this jack for head-phones. The TV's internal speakers can also be heard. Turn off the internal speakers by Audio, Advanced Settings, Options, if you wish to listen to the head-phones only.
NOTES: 1.
The HITACHI Plasma TV will appear to be turned OFF (lights orange) if there is no video input when VIDEO: 1, 2, 3, 4, 5, RGB1 or RGB2 is selected. Check the Power Light to make sure the Display Monitor is turned off or in Stand-by mode (lights red) when not in use. 2. Remote Control can not turn ON/OFF the "MAIN POWER" of the display monitor.
17
REAR PANEL JACKS
PT2-E/G AVC1-U
REAR PANEL OF THE AVC CENTER
ANT A
MONITOR OUT
S-VIDEO TO CONVERTER VIDEO
INPUT 4
S-VIDEO
INPUT 3
S-VIDEO
RGB 1
ANALOG INPUT
RGB 2
DIGITAL INPUT
TO MONITOR
VIDEO
VIDEO
Y/VIDEO INPUT 2 Y AUDIO (MONO) PB L PR R
INPUT 1
AUDIO (MONO) L
AUDIO
R
L
(MONO) ANT B L
(MONO) L
(MONO) L
PB PR
AUDIOR
L
IR BLASTER
R AUDIO AUDIO
R AUDIO
R
R
AUDIOR
L
AUDIO OUT
Antenna Input/Output The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a sub-picture.) The antenna output labeled "TO CONVERTER" allows the ANT A connection to pass directly to a different source such as a cable box, only when ANT B is displayed as a main picture. Audio/Video Inputs 1, 2, 3 and 4 The VID1~VID4 buttons will select each video source each time they are pressed. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable into the left audio jack.) MONITOR OUT These jacks provide fixed audio and video signals (ANT A/B, INPUT 2~5) which are used for recording. Use the S-VIDEO Output for high quality video output. Component signal to Input 1 and 2 will not have monitor output. AUDIO OUT These jacks provide fixed audio output for all audio sources (ANT A/B, INPUT1~5, and RGB 1/2) to a separate stereo amplifier. S-VIDEO Inputs 3 and 4 Inputs 3 and 4 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.
NOTES:
1. You may use VIDEO or S-VIDEO inputs to connect to INPUT 3 and 4, but only one of these inputs may be used at a time. 2. S-VIDEO output may be used for recording, only when the input is of S-VIDEO type.
Component: Y-PBPR Inputs Inputs 1 and 2 provide Y-PBPR jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may use standard video signal for INPUT 2. INPUT 1 does not accept composite video signal. NOTES: 1. DO NOT connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-Video has a higher priority over video input.
2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the AVC Box's PB input and the components R-Y output to the AVC Box's PR input. 3. Your component outputs may be labeled Y-CBCR. In this case, connect the component CB output to the AVC Box's PB input and the component CR output to the AVC Box's PR input. 4. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs. 5. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPR jacks.
18
PT2-E/G AVC1-U
RGB1 - Analog Input Use this 15-pin D-Sub input for your external devices with RGB output. RGB1 - Audio Input Connect audio for RGB1 input. RGB2 - Digital Input Use this RGB2 Digital input for your external devices with digital output capability. RGB2- Audio Input Connect audio for RGB2 input. To Monitor Connect the Monitor Connection Cable to the AVC center's "TO MONITOR" connector, and to the display monitors "FROM AVC" connector.
IR Blaster This jack provides IR output to your external components (VCR, Cable box, DVD player, etc.). With this connection, your external components can automatically be controlled by the A/V network feature. This connection will allow you to control the external components with your Plasma Television's remote control in TV mode. Subwoofer Out Connect the external audio component input to this SUB WOOFER OUT output. To AVC Connect the Monitor Connection cable from the AVC center's "TO MONITOR" to these connectors ("FROM AVC"). SUB-POWER button This power is for serviceman usage. It activates "Burn-in" mode for the Plasma Monitor. To enter to Burn-in mode, follow the next conditions and steps: Conditions: 1) Make sure Power Cord of AC line is connected to the PDP monitor. 2) The Main Power switch must be turned on. 3) The Monitor (DVI and DIN) connection cable must be unplugged from the Monitor. Procedure: 1) Press Sub-Power button for at least 7 seconds until a click is heard from the relays inside the monitor. The PDP screen will start a sequence of different color rasters. PDP MONITOR Self Diagnostic This button is also a troubleshooting aid, when a PDP monitor failure occurs, the pressing of the sub-power button, for more than 5 seconds, generates a blinking series of the power indicator light. The next table shows the PDP printed wired board (PWB) in which failure most probably would be allocated according to the number of blinks. Number of blinks of Presumed failing PWB power indication light * SDM: Scan Driver Module 1 Logic * ADM: Address Driver Module 2 Xsus 3 Ysus, SDM 4 Xsus, Ysus, SDM, POWER 5 Abus, ADM, POWER 6 ADM 7 ADM 8 ALL (All PWB's)
19
CONNECTING A/V NETWORK
PT2-E/G AVC1-U
The Hitachi Plasma Television is equiped with an A/V Network feature. This feature helps to control external Audio/Video equipment (VCR, Set Top Box, DVD, etc.). Once this is setup, it allows the IR Mouse connector to control equipment using the Hitachi Plasma TV Remote Control. You can use the Hitachi remote control to control the Audio/Video equipment command without the equipment's remote control. The Plasma Television AVC Center has 2 IR BLASTER jacks. Each IR Mouse cable can connect up to 2 external Audio/Video components. Therefore, you can connect the Plasma Television with up to four components. Please see the following example of an A/V Network setup between the Hitachi Plasma Television and external Audio/Video equipment (VCR and DVD Player). CONNECTING EXTERNAL AUDIO/VIDEO COMPONENTS TO IR BLASTER FOR A/V NETWORK 1. Connect external Audio/Video components to the AVC Center as shown in the example below. 2. 3. Connect the IR Mouse cable to the IR BLASTER output of the AVC Center. Place the IR mouse in front of the infrared sensor of the external components you wish to control.
Rear Panel of the AVC Center
ANT A
MONITOR OUT
S-VIDEO TO CONVERTER VIDEO
INPUT 4
S-VIDEO
INPUT 3
S-VIDEO
RGB 1
ANALOG INPUT
RGB 2
DIGITAL INPUT
TO MONITOR
VIDEO
VIDEO
Y/VIDEO INPUT 2 Y AUDIO (MONO) PB L PR R
INPUT 1
AUDIO (MONO) L
AUDIO
R
L
(MONO) ANT B L
(MONO) L
(MONO) L
PB PR
AUDIOR
L
IR BLASTER
R AUDIO AUDIO
R AUDIO
R
R
AUDIOR
L
AUDIO OUT
Y
V L OUTPUT R
OUTPUT PB/CB PR/CR R
L
Infrared Sensor VCR IR Mouse
Infrared Sensor
DVD Player
4.
Press the A/V NET button on the remote control. Use THUMB STICK or to highlight the component you wish to set up. Use THUMB STICK to enter component's "SOFT KEY" control button. The A/V Network Setup Wizard will automatically start upon the very first use. You can access the Setup Menu Wizard again in the future by pressing the A/V net button and selecting SETUP.
VCR Set Top Box Cable Box Amplifier DVD TV/VCR b MORE POWER CH CH SETUP
Move
NOTES:
1. 2. 3. 4.
The AVC Center has two IR BLASTER outputs which can control up to a total of four external components. The IR Mouse must be placed in front of the external components infrared sensor for the A/V Network to work. The correct codes must be entered for each of the Audio/Video components for the A/V Network to function properly. Audio/Video component codes for A/V network are on page 22.
20
A/V NETWORK SETUP WIZARD
5. Follow the steps below to setup the A/V network (See page 22 for A/V Network Codes).
PT2-E/G AVC1-U
There are six steps in the setup procedure (VCR setup example below).
HITACHI AV NET Wizard (step 1 of 6) This Wizard helps you with VCR connections and settings. Would you like to setup or modify your VCR? BACK NEXT HITACHI AV NET Wizard (step 2 of 6) Follow the digrams shown in Hitachi's Easy Graphic Guide to connect your VCR. Carefully position the IR "mouse" in front of your VCR as shown in the diagrams. BACK NEXT
HITACHI AV NET Wizard (step 3 of 6) Find your VCR 4-digit manufacturers code and enter it here - - - (Enter Code "9999" to uninstall) BACK NEXT Proper Code Entered from page xx. HITACHI AV NET Wizard (step 4a of 6) Which TV Rear Panel Input is connected to your VCR? (b) ANT A ( ) INPUT 3 ( ) ANT B ( ) INPUT 4 ( ) INPUT 1 ( ) INPUT 5 ( ) INPUT 2 BACK NEXT
ATTENTION The 4-digit code did not match AV Net's library. Please check and re-enter a valid code - - - -
If Error
BACK
NEXT
HITACHI AV NET Wizard (step 4b of 6) Which RF channel does your VCR use to send video to the TV? (b) Channel 03 ( ) Channel 04
ANT A,B
BACK
NEXT
HITACHI AV NET Wizard (step 5 of 6) Turn ON your VCR then press each of the 3 function keys below. Your VCR should respond to one of these keys. Now press NEXT to continue. POWER BACK PLAY CH UP NEXT
HITACHI AV NET Wizard (step 6 of 6) Did your VCR respond to POWER, PLAY or CH UP? Press DONE to finish this wizard or HELP to trouble shoot settings. HELP DONE
HITACHI AV NET Wizard Congratulations! Your VCR is now conected to your AV network.
DONE
HELP TROUBLE SHOOTING Please check connections shown in the EASY GRAPHIC GUIDE. If connections are correct, try a different manufacturers code for your VCR 0 4 3 6 BACK NEXT
From Step 3, once you enter "9999", the following message appears.
HITACHI AV NET Wizard (step 3b of 6) This will uninstall VCR on INPUT 1. Would you like to proceed?
BACK
YES
6.
Enter code "9999" to uninstall the equipment from your A/V Network.
21
AUDIO/VIDEO CODES FOR A/V NETWORK
VCR BRAND . . . . . . . . . . . . . . . . . . . . . . . CODE Admiral . . . . . . . . . . . . . . . . . . . . . . . . 0048, 0209 Adventura . . . . . . . . . . . . . . . . . . . . . . . . . . .0000 Aiko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278 Aiwa . . . . . . . . . . . . . . . . . . . . . 0307, 0000, 0037 Akai . . . . . . . . . . . . . . . . . 0106, 0053, 0041, 0061 America Action . . . . . . . . . . . . . . . . . . . . . . . 0278 American High . . . . . . . . . . . . . . . . . . . . . . . 0035 Asha. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240 Audiovox. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Beaumark. . . . . . . . . . . . . . . . . . . . . . . . . . . 0240 Bell & Howell . . . . . . . . . . . . . . . . . . . . . . . . 0104 Broksonic . . . . . . . . . . . . 0121, 0184, 0002, 0209, . . . . . . . . . . . . . . . . . . . . 0211, 0295, 0361, 0479 CCE . . . . . . . . . . . . . . . . . . . . . . . . . . 0072, 0278 Calix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Canon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035 Capehart . . . . . . . . . . . . . . . . . . . . . . . . . . . 0020 Carver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0081 Cineral . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278 Citizen . . . . . . . . . . . . . . . . . . . . . . . . 0278, 0037 Colt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072 Craig . . . . . . . . . . . 0037, 0072, 0047, 0240, 0271 Curtis Mathes. . . . . 0035, 0041, 0060, 0162, 0760 Cybernex . . . . . . . . . . . . . . . . . . . . . . 0051, 0240 Daewoo . . . . . . . . . . . . . . 0278, 0561, 0020, 0045 Daytron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0020 Denon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0042 Dynatech . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000 Electrohome . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Electrophonic . . . . . . . . . . . . . . . . . . . . . . . . 0037 Emerex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0032 Emerson . . . . . . . . 0184, 0002, 0209, 0278, 0036, . . . . . . . . . . . . . . . 0121, 0211, 0561, 0208, 0294, . . . . . . . . . . . . . . . 0479, 0061, 0088, 0212, 0000, . . . . . . . . . . . . . . . 0037, 0043, 0068, 0295, 0361 Fisher . . . . . . . . . . . . . . . 0047, 0104, 0054, 0066 Fuji . . . . . . . . . . . . . . . . . . . . . . . . . . . 0033, 0035 Funai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000 GE . . . 0035, 0060, 0048, 0202, 0240, 0760, 0761 Garrard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000 Go Video . . . . . . . . . . . . . 0432, 0526, 0232, 0643 GoldStar . . . . . . . . . . . . . . . . . . . . . . . 0037, 0038 Gradiente . . . . . . . . . . . . . . . . . . . . . . 0008, 0000 Grundig . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0195 HI-Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0047 Harley Davidson . . . . . . . . . . . . . . . . . . . . . . 0000 Harman/Kardon. . . . . . . . . . . . . . . . . . 0038, 0081 Harwood . . . . . . . . . . . . . . . . . . . . . . . 0068, 0072 Headquarter . . . . . . . . . . . . . . . . . . . . . . . . . 0046 Hitachi . . . . . . . . . . . . . . . 0042, 0105, 0000, 0041 Hughes Network Systems. . . . . . . . . . . . . . . 0042 JVC. . . . . . . . . . . . . . . . . . . . . . 0067, 0008, 0041 Jensen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0041 KEC . . . . . . . . . . . . . . . . . . . . . . . . . . 0037, 0278 KLH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072 Keen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0693 Kenwood . . . . . . . . . . . . . . . . . . 0041, 0067, 0038 Kodak . . . . . . . . . . . . . . . . . . . . . . . . . 0035, 0037 LXI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Lloyd's . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0208 Logik . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072 MEI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035 MGA . . . . . . . . . . . . . . . . . . . . . 0043, 0061, 0240 MGN Technology . . . . . . . . . . . . . . . . . . . . . 0240 MTC . . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0240 Magnasonic . . . . . . . . . . . . . . . . . . . . . . . . . 0278 Magnavox . . . . . . . . . . . . 0035, 0081, 0110, 0563, . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0039, 0149 Magnin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240 Marantz . . . . . . . . . . . . . . . . . . . . . . . 0081, 0035 Marta . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Matsushita. . . . . . . . . . . . . . . . . 0035, 0162, 0454 Memorex. . . . . . . . 0104, 0047, 0479, 0000, 0037, . . . . . . . . . . 0048, 0035, 0046, 0240, 1037, 0307, . . . . . . . . . . 0039, 0162, 0209, 0454, 1162, 1262 Minolta . . . . . . . . . . . . . . . . . . . . . . . . 0105, 0042 Mitsubishi. . . . . . . . 0173, 0061, 0043, 0048, 0067 Motorola . . . . . . . . . . . . . . . . . . . . . . . 0035, 0048 Multitech . . . . . . . . . . . . . . . . . . . . . . . 0000, 0072 NAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0058 NEC. . . . . . . . . . . . 0038, 0040, 0041, 0067, 0104 Nikko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Nikon . . . . . . . . . . . . . . . . . . . . . . . . . 0034, 0253 Noblex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240 Olympus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0035 Optimus . . . . . . . . 0162, 0454, 1062, 1162, 0048, . . . . . . . . . . 0058, 1262, 0037, 1048, 0104, 0432 Optonica. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0062 Orion . . . . . . . . . . . 0479, 0002, 0184, 0209, 0295 Panasonic . . . . . . . 0035, 0162, 0454, 1162, 0077, . . . . . . . . . . . . . . . 1062, 1262, 1362, 0225, 0616 Penney . . . . . . . . . . . . . . 0035, 0240, 0037, 0042, . . . . . . . . . . . . . . . . . . . . . . . . . 0038, 0040, 0054 Pentax . . . . . . . . . . . . . . . . . . . . . . . . 0042, 0105 Philco . . . . . . . . . . . . . . . . . . . . 0035, 0209, 0479 Philips . . . . . . . . . . . . . . 0081, 0035, 0062, 0618, . . . . . . . . . . . . . . . . . . . . . . . . . 0110, 1081, 1181 Pilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Pioneer . . . . . . . . . . . . . . . . . . . . . . . . 0058, 0067 Polk Audio . . . . . . . . . . . . . . . . . . . . . . . . . . 0081 Portland . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0020 Profitronic . . . . . . . . . . . . . . . . . . . . . . . . . . . 0240 Proscan . . . . . . . . . . . . . . 0060, 0202, 0760, 0761 Protec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0072 Pulsar . . . . . . . . . . . . . . . . . . . . . . . . . 0039, 0051 Quarter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0046 Quartz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0046 Quasar. . . . . . . . . . 0035, 0162, 0077, 0454, 1162 RCA . . . . . . 0060, 0149, 0202, 0042, 0058, 0105, . . . . . . 0035, 0048, 0077, 0106, 0240, 0760, 0761 Radio Shack . . . . . . . . . . . . . . . . . . . . 0000, 1037 Radix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Randex. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0037 Realistic . . . . . . . . . . . . . 0000, 0