Text preview for : TE555_English.pdf part of dsf sdf sdfdsfs
Back to : TE555_English.pdf | Home
Table of Contents
FCC Statement Energy Declaration Important Safeguards Technical Support Package Installation On-Screen Display Guide OSD Operation Specifications Trouble Shooting 1 1 2 2 3 4 4 5 8 9
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
1 FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: . Reorient the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio TV technician for help. Notice: 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interference cables must be used in order to comply with the emission limits.
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
2 Important Safeguards
1. Follow all warnings and instructions marked on the video monitor. 2. Do not use attachments which is not recommended by the video monitor manufacturer as they may cause hazards. 3. Do not expose the monitor to rain, water, moisture or direct sunlight. 4. Do not place near or over a radiator or other heat-generating equipment. 5. Do not place this video monitor on unstable cart, stand or table. The video monitor may fall and cause serious injury to child or adult. 6. Do not block or cover ventilation opening with any material. The openings & slots on the cabinet provide necessary air flow for heat dissipation. The unit should never be enclosed or built upon unless adequate ventilation is provided. 7. Do not insert any objects into the video monitor cabinet's slots as they may touch dangers voltage points or short out parts that could result in a fire or electric shock. 8. This video monitor is equipped with a 3-wire grounding type plug. The plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert plug into outlet, contact your electrician to replace your obsolete. Do not defeat the safety purpose of the grounding type plug. 9. Do not overload wall outlets & extension cords as this can result in fire or electric shock. 10. Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. 11. When the video monitor unused for a long time, please unplug it from the wall outlet 12. Unplug this video monitor from the wall outlet and refer servicing under following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the video monitor c. If the video monitor does not operate normally according to operating instructions. d. If the video monitor has been dropped or the cabinet has been damaged
Technical Support
If you encounter particular problems that cannot be resolved by you, please contact with your local dealer for the technical support. To avoid possible damages or hazards arising from improper operation, please do not attempt to service the monitor yourself. TECO Electric & Machinery Co., Ltd. 1568 Chung Shan Rd., Sec.1, Kuang In, Taoyuan Hsien, Taiwan, R.O.C. TEL. : +886-3-473-3111 FAX : +886-3-473-3126
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
3 Energy Declaration
This monitor is equipped with a function for saving of energy which supports the VESA Display Power Management Signaling ( DPMS ) standard. This means that the monitor must be connected to a computer which supports VESA DPMS to fulfill the requirement in the NUTEK specification. Time settings are adjusted from the system unit by software. From indicated inactivity to Power Saving Position A2 the total time must not be set to more than 70 minutes. NUTEK Normal operation Power Saving Position A1 Power Saving Position A2 VESA State ON SUSPEND STAND-BY OFF LED Indicator Green Yellow Orange Power Consumption 80W (Max.) 15 W (Max.) 5 W (Max.)
We recommend you to switch off the monitor when it is not in use for quite a long time.
Package
Determine the most convenient location for your monitor. Make sure that you have enough room to install cables and connect the monitor to the system and power supply. 1. Open the shipping carton and check the contents of the package. The package should include the following items : Color Monitor Power Cord User's Manual Note: If any item(s) are missing or damaged, contact your dealerimmediately. 2. Remove the monitor from its shipping carton(see figure 1). Save the carton and packaging materials in case you need to relocate the monitor.
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
4 Installation
Figure 1 1. Tilt Swivel & Base (refer to figure 1) A. Turn the monitor upside down.
Figure 2
B. Turn the base upside down. Insert its four hooks into the four slots on the bottom of the monitor. (Point the hooks on the base toward the front of the monitor) C. Push the tilt swivel and base in the direction of arrow as indicated in Figure 1 to lock the hooks. 2. Monitor Connection (refer to figure 2) A. Turn off the monitor and computer. B. Connect one end of the power cable to your monitor and the other end to the power outlet. C. Connect the 15-pin D-Sub signal cable to the video adapter output on your personal computer. D. Turn on the monitor and the computer. Wait about 30 seconds to adjust the picture with the adjustment controls to obtain optimum picture. E. If the signal cable is not connected to the PC, then the screen will display the Color Bar Pattern.
On-Screen Display Guide
63
32
Figure 3 : Contrast Adjustment B ar
Figure 4 : Brightness Adjustment Bar
1. 2.
Contrast Brightness
Press "5" "6" to activate and make the contrast adjustment by the OSD bar. Press "3" "4" to activate and make the brightness adjustment by the OSD bar.
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
5
3. Control Panel
1. Power ON / OFF Switch 2. Power LED 3. Menu 4. Function Control Key
Figure 5 : Control Key
OSD Operation
Figure 6 : Function Menu
52
H-Phase/V-Center
A. B. Press "Menu" key (Figure 5 ) to enter the OSD menu containing 10 functions as shown in Figure 6 . Select OSD function 1. Press "MENU" key to select OSD function (Figure 6) 2. Keep pressing the Menu key. You may return to the previous item. C. OSD Adjustment 1. Make adjustment by using the four function control keys 3utor 4 ( Refer to Figure 5 ) 2. Pressing the four control keys , there are four adjustments for each function. The icon selected will turn into a different color. 3. The setting value will appear on the MENU during adjustment. 4. The bottom of OSD MENU will display the message of current function selected. 5. The number in the right lower corner indicates how long the OSD will last for display.
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
6 OSD Function
H-Phase & V-Center Position (Please refer to Figure 6 ) Press 3 or 4 key to reposition the picture leftward or rightward. press 5 or 6 key to reposition the picture upward or downward. H-Size & V-Size adjustment Press 3 key to reduce the H-size and press 4 key to enlarge the H-size. Press 5 to enlarge the V-size and press 6 key to reduce the V-size. Pincushion & Trapezoid adjustment Press key 3 and 4 on the control panel to alter pincushion and barrel Press key 5 and 6 on the control panel to alter trapezoid Geometry Adjustment Press 3 and 4 to adjust pin balance. Pressu and t to adjust corner distortion. Parallelogram Press 3 and 4 to adjust parallelogram . Color temperature adjustment 1. Using this function you can fine-tune the representation of the primary colors red, green, And blue ("User's mode) or select one of the preset color temperatures (65000 K , 75000 K, or 93000 K). 2. Choose the desired color temperature by using the two function keys u and t then adjust the setting value by using another two function keys 3 and 4
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
7
OSD Position adjustment Press 3utor 4 to move OSD , You may reposition OSD Language adjustment Press u and t to select your desired language, and then the OSD menu will be presented in the language selected. Tool function Use the u and t button to select the desired sub-function. Then adjust / activate the function by using the 3 and 4 button 1. 2. 3. Factory setting recall. Adjust OSD countdown timer whose duration ranges from 5 to 240 seconds. The 15" model does not provide the degaussing function. NOTE 1 : You have alternative of switching off the monitor, then Switch on again, it will automatically perform degaussing function. NOTE 2 : It's recommended to wait 15 minutes before user to make next degaussing activity , no matter auto or manual degaussing was performed last time. 4. 5. Exit 1.This sub-menu allows you to close the OSD menu by pressing one of the OSD buttons. 2.Furthermore, this OSD sub-menu displays a summary of the current OSD settings and information on the current graphics mode.( horizontal and vertical frequency ). Enable or disable power saving Select the video input level
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
8 Specifications
CRT SIZE Viewable area Dot pitch 15" diagonal, 900 deflection 13.7" 0.28mm
Input Signal Input Connector Scanning frequency Active Display Area Resolution Pixel Rate Power consumption Power Supply
Video: Analog (0.7Vp-p/1.0 Vp-p, 75 ohm positive) Selected by OSD Control Sync : Separate sync, positive or negative TTL 15-pin D-connector Horizontal:30KHz-54KHz , Vertical: 50Hz-120Hz Horizontal: 268 mm ( adjustable ) Vertical: 198 mm ( adjustable ) 1024x768 800x600 80MHz (maximum) 80W (max.) Line voltage: 100 VAC- 240 VAC Frequency: 50±3 Hz ,60±3Hz 640x480
X-Radiation Power Management Plug & Play Ambient Temperature Humidity Regulations LED Indicators
Meets DHHS requirements Meets EPA/NUTEK requirements Satisfies DDC1 and DDC2B specifications 0 10 ~ 35 (operating) ,-10 - 80 ~ 60 (storage)
UL , C-UL , TUV , GS , ERGONOMICS , MPRII , CE Green (ON state),Yellow (Stand-by and Suspend), Orange (OFF state)
Weight
N.W. 12 kgs (approx.)
G.W. 14 kgs (approx.)
Note: This user's manual for TE555 series containing graphics and information is for reference purpose only , which is subject to change without notice
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com
9 Trouble Shooting
? No picture 1. The VGA card should be completely seated in the slot. 2. Power switch of the monitor and the PC should be in the ON position. 3. The signal cable should be completely connected to the video card / computer. 4. Check if the pins of the connector are twisted or shrunk. ? Image is scrolling or unstable 1. The signal cable should be completely connected to computer. 2. Check the pin assignments and signal timings of the monitor and your video card. ? LED on the monitor is not lit 1. Power switch should be in the ON position and the power cord should be connected. 2. Check if the system is in the power saving mode. ( Check by pressing any one of keys on the keyboard or moving the mouse.) ? Picture is fuzzy 1. Adjust the Contrast and Brightness Controls. ? Picture bounces or wave pattern is present in the picture 1. Move electrical devices that may be causing electrical interference away from the monitor. 2. Refer to the FCC information of this manual. ? Image edges distorted. 1. Using Geometry adjustment or parallelogram & tilt adjustment (see page 5) 2. Locate the monitor facing to east. ? Display image is not centered, too small, or too large 1. Adjust the image using Size and Position Controls in the OSD. ? Colors are distorted in some area. 1. Demagnetize your monitor (see page 6 tool function) ? Color is off (e.g. white is not really displayed as white etc.) 1. adjust color temperature (see page 5 Color temperature adjustment)
PDF created with FinePrint pdfFactory trial version http://www.fineprint.com