Text preview for : Sony DSC-P52 Level 1 - MS.pdf part of sony DSC-P52 sony DSC-P52 service manual
Back to : Sony DSC-P52.part1.rar | Home
DSC-P52
SERVICE MANUAL
Ver 1.0 2003. 03
Revision History LEVEL
1
US Model Canadian Model AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Brazilian Model
Link
SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
· INSTRUCTION MANUAL is shown at the end of this document.
DIGITAL STILL CAMERA
DSC-P52
COVER
SPECIFICATIONS
x Camera [System]
Image device 6.67 mm (1/2.7 type) color CCD Primary color filter Total pixels number of camera Approx. 3 340 000 pixels Effective pixels number of camera Approx. 3 210 000 pixels Lens 2× zoom lens f=6.3 to 12.6 mm (35 mm camera conversion: 41 to 82 mm (1 5/8 to 3 1/4 inches)) F3.8 Exposure control Automatic, Program, Twilight, Twilight portrait, Landscape, Snow, Beach White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent File format (DCF compliant) Still images: Exif Ver. 2.2, JPEG compliant, GIF (for Clip Motion), DPOF compatible Audio with still image: MPEG1 compliant (Monaural) Movies: MPEG1 compliant (Monaural) Recording media "Memory Stick" Flash Recommended distance 0.5 to 3.3 m (19 3/4 inches to 10 feet 9 29/32 inches)
[LCD screen]
LCD panel used 4.0 cm (1.6 type) TFT drive Total number of dots 61 600 (280×220) dots
x AC-LS5 AC Adaptor (not supplied)
Power requirements AC 100 to 240 V, 50/60 Hz 11 W 0.16 to 0.09 A Rated output voltage DC 4.2 V, 1.5 A Operating temperature range 0° to +40°C (32° to +104°F) Storage temperature range 20° to +60°C (4° to +140°F) Dimensions 48 × 29 × 81 mm (1 15/16 × 1 3/16 3 1/4 inches) (W/H/D, protruding parts not included) Mass Approx. 180 g (6 oz) (adaptor only)
[Power, general]
Power AA nickel hydride batteries (2) 2.4 V AC-LS5 AC Adaptor (not supplied), 4.2 V Power consumption (when recording) 1.6W Operating temperature range 0° to +40°C (32° to +104°F) Storage temperature range 20° to +60°C (4° to +140°F) Dimensions 123.2 × 57.7 × 52 mm (4 7/8 × 2 3/8 × 2 1/8 inches)
Approx. 280 g (9.9 oz) (two batteries, "Memory Stick" and wrist strap included) Microphone Electret condenser microphone Speaker Dynamic speaker
Accessories
HR6 (size AA) Ni-MH batteries (2) Battery case BC-CS2A/CS2B Ni-MH Battery charger (1) Power cord (mains lead) (1) USB cable (1) A/V connecting cable (1) Wrist strap (1) "Memory Stick" (16MB) (1) CD-ROM (USB driver: SPVD-010) (1) Operating Instructions (1)
Mass
x BC-CS2A/CS2B Ni-MH battery charger
Power requirements AC 100 to 240V 50/60Hz 3W Output voltage AA : DC 1.4 V 400 mA × 2 AAA : DC 1.4 V 160 mA × 2 Operating temperature range 0° to +40°C (32° to +104°F) Dimensions 71 × 30 × 91 mm (2 7/8 × 1 3/16 × 3 5/8 inches) (W/H/ D) Mass Approx. 90 g (3 oz)
Design and specifications are subject to change without notice.
[Output connectors]
A/V OUT (MONO) jack (Monaural) Minijack Video: 1 Vp-p, 75 , unbalanced, sync negative Audio: 327 mV (at a 47 k load) Output impedance 2.2 k USB jack mini-B
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
--2--
DSC-P52
Checking supplied accessories.
Make sure that the following accessories are supplied with your camcorder.
Power cord (1)(AUS model) 0 1-696-819-21 Power cord (1)(AEP,E model) 0 1-769-608-11 Power cord (1)(CH model) 0 1-782-476-13 Power cord (1)(KR model) 0 1-776-985-11 Power cord (1)(UK,HK model) 0 1-783-374-11 Power cord (1)(US,CND model) 0 1-790-107-22 Power cord (1)(JE model) 0 1-790-732-12
Battery charger (BC-CS2)(1) (US,CND,JE model) 0 1-477-814-11 Battery charger (BC-CS2)(1) (AEP,UK,E,HK,AUS,BR model) 0 1-477-814-21 Battery charger (BC-CS2)(1) (CH, KR model) 0 1-477-814-32
Connection cord (AV Cable 1.5m)(1) 1-824-111-11
Hand strap (1) 3-070-841-01
Battery carrying case (1) 3-074-757-01
Cord with connector (1) (USB 5P) 1-827-038-11
CD-ROM (USB DRIVER) (1) (SPVD-010) (AEP,UK,E,HK,AUS, CH,JE,KR,BR model) 3-078-942-03 CD-ROM (USB DRIVER) (1) (SPVD-010 (I)) (US,CND model) 3-078-943-03
Memory stick (1) (MSA-16A) (not supplied) 2P conversion adaptor (1) (JE model) 1-569-007-12 2P conversion adaptor (1) (E model) 1-569-008-12
HR6 (size AA) Ni-MH batteries (not supplied)
Other accessories
3-082-146-11 MANUAL, INSTRUCTION (ENGLISH) (US,CND,AEP,UK,E,HK,AUS,CH,JE) 3-082-146-21 MANUAL, INSTRUCTION (FRENCH/GERMAN) (CND,AEP,JE) 3-082-146-31 MANUAL, INSTRUCTION (SPANISH/PORTUGUESE) (AEP,E,JE) 3-082-146-41 MANUAL, INSTRUCTION (ITALIAN/DUTCH) (AEP) 3-082-146-51 3-082-146-61 3-082-146-71 3-082-146-81 MANUAL, INSTRUCTION (CHINESE) (E,HK,CH,JE) MANUAL, INSTRUCTION (RUSSIAN/SWEDISH) (AEP,JE) MANUAL, INSTRUCTION (ARABIC) (E) MANUAL, INSTRUCTION (KOREAN) (KR,JE)
· Abbreviation CND : Canadian model HK : Hong Kong model AUS : Australian model CH : Chinese model
JE KR BR
: Tourist model : Korea model : Brazilian model
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering.
2. 3.
--3--
DSC-P52
COVER
SELF-DIAGNOSIS FUNCTION
[Description on Self-diagnosis Display]
Self-diagnosis display · C: ss: ss The contents which can be handled by customer, are displayed. · E: ss: ss The contents which can be handled by engineer, are displayed. Display Code C:32:01 Countermeasure Turn off the main power then back on. Replace the memory stick. Format the memory stick with the DSC-P52. Cause Trouble with hardware. · The type of memory stick that cannot be used by this machine, is inserted. · Data is damaged. · Unformatted memory stick is inserted. When failed in the focus initialization. Caution Display During Error SYSTEM ERROR
C:13:01
MS ERROR
E:61:00 *1 Checking of lens drive circuit E:61:10 *1 E:91:01 Checking of flash unit or replacement of flash unit. Abnormality when flash is being charged. Flash LED Flash display Flashing at 3.2 Hz --
Note : The error code is cleared if the battery is removed, except defective flash unit. *1: The error display is given in two ways.
--4--
DSC-P52
COVER
Note:
MAIN PARTS
· The parts numbers of such as a cabinet are also appeared in this section. Refer to the parts number mentioned below the name of parts to order.
1.
ORNAMENTAL PARTS
Jack cover 3-080-985-01 (When change it, need to dismantle the set.)
--5--
DSC-P52
9-876-248-41
Sony EMCS Co.
--6--
2003C1600-1 ©2003.3 Published by DI Customer Center
3-082-146-11(1)
Getting started ________________________
Digital Still Camera
Operating Instructions
Before operating the unit, please read this manual thoroughly, and retain it for future reference.
Shooting still images __________________
Viewing still images ___________________
Deleting still images ___________________
Owner's Record
The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. DSC-P32/P52/P72 Serial No.
Before advanced operations _____________
Advanced still image shooting ____________
Advanced still image viewing_____________
Still image editing ______________________
Enjoying movies________________________
Enjoying images on your computer ______
Troubleshooting ________________________
Additional information ___________________
DSC-P32/P52/P72
© 2003 Sony Corporation
Index _____________________________
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
If you have any questions about this product, you may call: Sony Customer Information Services Center 1-800-222-SONY (7669) The number below is for the FCC related matters only. Regulatory Information
Declaration of Conformity
Trade Name: SONY Model No.: DSC-P52 Responsible Party:Sony Electronics Inc. Address: 680 Kinderkamack Road, Oradell, NJ 07649 USA Telephone No.: 201-930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For the Customers in the U.S.A.
Declaration of Conformity
Trade Name: SONY Model No.: DSC-P32 Responsible Party:Sony Electronics Inc. Address: 680 Kinderkamack Road, Oradell, NJ 07649 USA Telephone No.: 201-930-6972 This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Declaration of Conformity
Trade Name: SONY Model No.: DSC-P72 Responsible Party:Sony Electronics Inc. Address: 680 Kinderkamack Road, Oradell, NJ 07649 USA Telephone No.: 201-930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
For the Customers in the U.S.A. and Canada RECYCLING NICKEL METAL HYDRIDE BATTERIES
Nickel Metal Hydride batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you. For more information regarding recycling of rechargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/ Caution: Do not handle damaged or leaking Nickel Metal Hydride batteries.
Notice on the supplied battery charger for the customers in the United Kingdom
A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362, (i.e., marked with or mark) must be used. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. The supplied interface cable must be used with the equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
For the Customers in Europe
This product has been tested and found compliant with the limits sets out in the EMC Directive for using connection cables shorter than 3 meters (9.8 feet).
CAUTION
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
Attention
The electromagnetic fields at the specific frequencies may influence the picture and sound of this digital camera.
Notice
If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the application or disconnect and connect the USB cable again.
3
Certain countries may regulate disposal of the battery used to power this product. Please consult with your local authority.
Before using your camera
Trial recording Do not shake or strike the camera
In addition to malfunctions and inability to record images, this may render the "Memory Stick" unusable or image data breakdown, damage or loss may occur. Before you record one-time events, you may want to make a trial recording to make sure that the camera is working correctly.
"Memory Stick"
N50
No compensation for contents of the recording
Contents of the recording cannot be compensated for if recording or playback is not possible due to a malfunction of your camera or recording medium, etc.
LCD screen, LCD finder (only models with a LCD finder) and lens
· The LCD screen and the LCD finder are manufactured using extremely highprecision technology so over 99.99% of the pixels are operational for effective use. However, there may be some tiny black points and/or bright points (white, red, blue or green in color) that constantly appear on the LCD screen and the LCD finder. These points are normal in the manufacturing process and do not affect the recording in any way. · Be careful when placing the camera near a window or outdoors. Exposing the LCD screen, the finder or the lens to direct sunlight for long periods may cause malfunctions. · Do not press the LCD screen hardly. The screen may be uneven and that may cause a malfunction. · Images may be trailed on the LCD screen in a cold location. This is not a malfunction.
For the Customers in the U.S.A. and Canada
THIS CLASS B DIGITAL DEVICE COMPLIES WITH PART 15 OF THE FCC RULES AND THE CANADIAN ICES-003 OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Back up recommendation
To avoid the potential risk of data loss, always copy (back up) data to a disk.
Notes on image data compatibility
· This camera conforms with the Design rule for Camera File system universal standard established by the JEITA (Japan Electronics and Information Technology Industries Association). · Playback of images recorded with your camera on other equipment and playback of images recorded or edited with other equipment on your camera are not guaranteed.
Precaution on copyright
Television programs, films, video tapes, and other materials may be copyrighted. Unauthorized recording of such materials may be contrary to the provision of the copyright laws.
The power zoom lens (for the DSCP72 only)
This camera is equipped with power zoom lens. Be careful not to bump the lens, and be careful not to apply force to it.
4
Remove dirt from the surface of the flash
If the dirt changes color or sticks to the surface of the flash due to the heat of the flash, sufficient light may not be emitted.
The pictures used in this manual
The photographs used as examples of pictures in this manual are reproduced images, and are not actual images shot using this camera.
Trademarks
· "Memory Stick," , and "MagicGate Memory Stick" are trademarks of Sony Corporation. · "Memory Stick Duo" and are trademarks of Sony Corporation. · "Memory Stick PRO" and are trademarks of Sony Corporation. · "MagicGate" and are trademarks of Sony Corporation. · Microsoft and Windows are registered trademarks of the U.S. Microsoft Corporation in the United States and other countries. · Macintosh, Mac OS, QuickTime, iBook, and Power Mac are trademarks or registered trademarks of Apple Computer, Inc. · "Pentium" is a trademark or a registered trademark of Intel Corporation. · In addition, system and product names used in this manual are, in general, trademarks or registered trademarks of their respective developers or manufacturers. However, the TM or ® marks are not used in all cases in this manual.
Do not get the camera wet
When taking pictures outdoors in the rain or under similar conditions, be careful not to get the camera wet. If moisture condensation occurs, see page 108 and follow the instructions on how to remove it before using the camera.
The illustrations and screen status used in this manual
The illustrations and screen status used in this manual are of the DSC-P72 unless noted otherwise.
Do not expose the camera to sand or dust
Using the camera in sandy or dusty locations may cause a malfunction.
Do not aim the camera at the sun or other bright light
This may cause irrecoverable damage to your eyes or the malfunction of your camera.
Notes on locations where you can use the camera
· Do not use the camera near a location that generates strong radio waves or emits radiation. The camera may not be able to record or play back properly. · Do not use the camera near a TV, radio, or tuner. This may cause noise to interfere the camera.
5
Table of contents
Before using your camera ......................... 4 Identifying the parts .................................. 8 Inserting the date and time on a still image.............................................. 35
Advanced still image shooting
Choosing a focus method........................48 Setting the distance to the subject Focus preset .................................49 Adjusting the exposure EV adjustment .............................50 Selecting a metering mode......................51 Adjusting color tones White Balance...52 Adjusting the flash level Flash level ....53 Shooting multiple frames Clip Motion .................................54 Shooting in Multi Burst mode Multi Burst...................................55 Shooting two images in succession Burst 2 .........................................56 Shooting still images for e-mail E-Mail..........................................56 Shooting still images with audio files Voice............................................57 Shooting according to scene conditions ........................................................58 Adding special effects Picture Effect ...............................60
Getting started
Preparing batteries .................................. 14 Charging the batteries ............................. 14 Inserting the batteries.............................. 16 Using an external power source.............. 19 Using your camera abroad ...................... 19 Turning your camera on/off .................... 20 How to use the control button................. 20 Setting the date and time......................... 21
Viewing still images
Viewing images on the LCD screen of your camera ............................................ 36 Viewing images on a TV screen............. 38
Deleting still images
Deleting images ...................................... 40 Formatting a "Memory Stick" ................ 44
Shooting still images
Inserting and removing a "Memory Stick" ........................................................ 23 Setting the still image size ...................... 24 Image size and quality ............................ 25 Basic still image shooting using auto mode........................... 26 Checking the last image shot Quick Review .............................. 28 Using the zoom feature....................... 29 Shooting close-ups Macro (DSC-P72 only).............................. 30 Using the self-timer ............................ 31 Selecting a flash mode........................ 32 Shooting with the finder ..................... 34
Before advanced operations
How to setup and operate your camera ........................................................ 45 Changing menu settings ..................... 45 Changing items in the SET UP screen ........................................................ 45 Deciding the still image quality.............. 46 Creating or selecting a folder ................. 46 Creating a new folder ......................... 47 Selecting the recording folder ............ 47
6
Advanced still image viewing
Selecting the folder and playing back images Folder ..............................61 Enlarging a portion of a still image.........62 Enlarging an image Playback zoom.............................62 Recording an enlarged image Trimming .....................................63 Playing back successive images Slide show....................................63 Rotating still images Rotate .................64 Playing back images shot in Multi Burst mode ...............................................65 Playing back continuously ..................65 Playing back frame by frame Jog playback ................................65
Enjoying movies
Shooting movies ..................................... 72 Viewing movies on the LCD screen....... 73 Deleting movies ...................................... 74 On the single screen............................ 74 On the Index (nine-image) screen ...... 74 On the Index (triple-image) screen..... 75 Editing movies ........................................ 76 Cutting movies.................................... 76 Deleting unnecessary portions of movies ........................................................ 77
Image file storage destinations and file names ..............................................86 Copying images to your computer For Macintosh users.....................88 Creating a Video CD ...............................90
Troubleshooting
Troubleshooting ......................................91 Warnings and messages ..........................98 Self-diagnosis display If a code starting with an alphabet letter appears......100
Enjoying images on your computer
Copying images to your computer For Windows users...................... 78 Installing the USB driver.................... 79 Installing "Image Transfer"................ 80 Installing "ImageMixer"..................... 81 Connecting the camera to your computer ........................................................ 82 Copying images using "Image Transfer" ........................................................ 83 Changing "Image Transfer" settings .. 84 Copying images without using "Image Transfer" ........................................ 84 Viewing the images on your computer ........................................................ 85
Additional information
The number of images that can be saved/ shooting time.................................101 Menu items............................................102 SET UP items ........................................106 Precautions ............................................108 The "Memory Stick" .............................109 The nickel-metal hydride batteries ........110 The battery charger................................111 Specifications ........................................111 The LCD screen ....................................113
Still image editing
Protecting images Protect.....................67 On the single screen ............................67 On the Index (nine-image) screen.......67 On the Index (triple-image) screen .....68 Changing image size Resize.................69 Choosing images to print Print (DPOF) mark ......................70 On the single screen ............................70 On the Index (nine-image) screen.......70 On the Index (triple-image) screen .....71
Index
Index......................................................116
7
Identifying the parts
(DSC-P72)
1 2 3 4 5 6
7 8 9 q; qa
A B C D E F G H I
8
POWER button (20) Shutter button (26) Flash (32) Microphone Self-timer lamp (31)/ AF illuminator (33) Tripod receptacle (bottom surface) POWER lamp (20) Finder window Lens
J Access lamp (23) K "Memory Stick" cover (23)
· "3.2MEGA PIXELS" shown on the surface of the camera is the number of effective pixels of the CCD. However, the maximum number of pixels recorded is 3.1 mega pixels. The indication of the number of effective pixels of the CCD is a recommendation of the JCIA (Japan Camera Industry Association).
· Use a tripod with a screw length of less than 5.5 mm (7/32 inch). You will be unable to firmly secure the camera to tripods having longer screws, and may damage the camera.
1 2 3 4 5 6 7 8 9
A Zoom buttons (during shooting) (29)/Index buttons (during playback) (37) B Control button (Menu on) (v/V/b/B/z) (20)/ (Menu off) ( / /7/ ) (32/31/28/ 30) C Mode selector (21) : To view or edit images : To shoot still images : To shoot movies/Clip Motion images/Multi Burst mode images SET UP: To set the SET UP items D Finder (34)
q; qa qs qd qf qg qh qj
J K L M N O P
RESET button (91) DC IN jack (19) (USB) jack (82) A/V OUT (MONO) jack (38) Battery cover OPEN button (16) Wrist strap hook
Attaching the wrist strap
Q Jack cover Self-timer/recording lamp (red) (31/27) AE/AF lock lamp (green) (26) (Flash charge) lamp (orange) (32)
E LCD screen F Speaker G MENU button (102) H (LCD status/LCD on/off) button (34) I (Image Size/Delete) button (24/40)
9
Identifying the parts (continued) (DSC-P52)
1 2 3 4 5 6
7 8 9
q; qa
A B C D E F G H I
10
POWER button (20) Shutter button (26) Flash (32) Microphone Self-timer lamp (31)/ AF illuminator (33) Tripod receptacle (bottom surface) POWER lamp (20) Finder window Lens
J Access lamp (23) K "Memory Stick" cover (23)
· "3.2MEGA PIXELS" shown on the surface of the camera is the number of effective pixels of the CCD. However, the maximum number of pixels recorded is 3.1 mega pixels. The indication of the number of effective pixels of the CCD is a recommendation of the JCIA (Japan Camera Industry Association).
· Use a tripod with a screw length of less than 5.5 mm (7/32 inch). You will be unable to firmly secure the camera to tripods having longer screws, and may damage the camera.
1 2 3 4 5 6 7 8 9
A Zoom buttons (during shooting) (29)/Index buttons (during playback) (37) B Control button (Menu on) (v/V/b/B/z) (20)/ (Menu off) ( / /7/ ) (32/31/28/ 51) C Mode selector (21) : To view or edit images : To shoot still images : To shoot movies/Clip Motion images/Multi Burst mode images SET UP: To set the SET UP items D Finder (34)
q; qa qs qd qf qg qh qj
J K L M N O P
RESET button (91) DC IN jack (19) (USB) jack (82) A/V OUT (MONO) jack (38) Battery cover OPEN button (16) Wrist strap hook
Attaching the wrist strap
Q Jack cover Self-timer/recording lamp (red) (31/27) AE/AF lock lamp (green) (26) (Flash charge) lamp (orange) (32)
E LCD screen F Speaker G MENU button (102) H (LCD status/LCD on/off) button (34) I (Image Size/Delete) button (24/40)
11
Identifying the parts (continued) (DSC-P32)
1 7 2 8 3 9 4 5 6 q; qa
A B C D E F
12
POWER button (20) Shutter button (26) Flash (32) Finder window Lens Tripod receptacle (bottom surface) G POWER lamp (20) H Microphone I Self-timer lamp (31)/ AF illuminator (33)
J Access lamp (23) K "Memory Stick" cover (23)
· "3.2MEGA PIXELS" shown on the surface of the camera is the number of effective pixels of the CCD. However, the maximum number of pixels recorded is 3.1 mega pixels. The indication of the number of effective pixels of the CCD is a recommendation of the JCIA (Japan Camera Industry Association).
· Use a tripod with a screw length of less than 5.5 mm (7/32 inch). You will be unable to firmly secure the camera to tripods having longer screws, and may damage the camera.
1 2 3 4 5 6 7 8 9
A Zoom buttons (during shooting) (29)/Index buttons (during playback) (37) B Control button (Menu on) (v/V/b/B/z) (20)/ (Menu off) ( / /7/ ) (32/31/28/ 51) C Mode selector (21) : To view or edit images : To shoot still images : To shoot movies/Clip Motion images/Multi Burst mode images SET UP: To set the SET UP items D Finder (34)
q; qa qs qd qf qg qh qj
J K L M N O P
RESET button (91) DC IN jack (19) (USB) jack (82) A/V OUT (MONO) jack (38) Battery cover OPEN button (16) Wrist strap hook
Attaching the wrist strap
Q Jack cover Self-timer/recording lamp (red) (31/27) AE/AF lock lamp (green) (26) (Flash charge) lamp (orange) (32)
E LCD screen F Speaker G MENU button (102) H (LCD status/LCD on/off) button (34) I (Image Size/Delete) button (24/40)
13
Getting started
Preparing batteries
Use the following batteries in this camera. Acceptable batteries HR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2)
NH-AA-DA (2) (supplied) NH-AA-2DA twin-pack (not supplied)
Charging the batteries
CHARGE lamp
to a wall outlet (wall socket)
R6 (size AA) alkaline batteries (2) Batteries that cannot be used Manganese batteries, lithium batteries, nicad batteries If you use the batteries described above, we cannot guarantee full performance of the camera by property of the batteries, such as brownout of the batteries. The battery remaining indicator does not display the correct information.
· When alkaline batteries are used, take note of the following information. There is a big difference in the performance of batteries of different types and of batteries made by different manufacturers. This is especially true in low temperatures, where some batteries are noticeably weaker. You may not be able to shoot in temperatures below 5°C (41°F). The battery remaining indicator may not display the correct information.
1
, Insert Nickel-Metal Hydride batteries into the battery charger (supplied) with the correct polarity +/-.
· You cannot charge alkaline batteries using the battery charger. · Be sure to charge the Nickel-Metal Hydride batteries supplied with your camera before using them. · Connect the battery charger to an easily accessible wall outlet (wall socket) close by. · Even if the CHARGE lamp is not lit, the set is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet (wall socket). If some trouble occurs while using the battery charger, immediately shut off the power by disconnecting the plug from the wall outlet (wall socket).
2
Power cord (mains lead)
, Connect the battery charger to a wall outlet (wall socket) using the power cord (mains lead).
Charging starts, and the CHARGE lamp lights. When the CHARGE lamp goes out, charging is finished. For details on the battery charger, see page page 111. To remove the batteries Press the - end of the battery down in order to raise the + end, then remove the battery.
· When charging is finished, disconnect the power cord (mains lead) from the wall outlet (wall socket), and remove the Nickel-Metal Hydride batteries from the battery charger.
14
Charging time
Nickel-Metal Hydride battery NH-AA-DA × 2
(supplied) This represents the time required to charge fully depleted Nickel-Metal Hydride batteries using the supplied battery charger in an environment where the ambient temperature is 25°C (77°F). · Charging is complete in approximately six hours. The CHARGE lamp may remain lit longer than six hours, but this is not a malfunction. · If you use the BC-CSQ2 battery charger supplied with the STAMINA "Super Quick charge" kit (not supplied), the batteries will charge faster. Charging time When charging two Nickel-Metal Hydride batteries: Approximately 2 hours 30 minutes When charging four Nickel-Metal Hydride batteries: Approximately 5 hours
Charging time
Approx. 6 hours
Notes on the Nickel-Metal Hydride batteries
· If the poles of the Nickel-Metal Hydride batteries are dirty, the batteries may not charge properly. Occasionally clean the poles of the batteries and the terminals of the charger by wiping them with a dry cloth. · When transporting the Nickel-Metal Hydride batteries, be sure to use the battery case (supplied). If the +/- metal terminals are shorted, there is a possibility of danger from excessive heat or fire. · At the time of purchase, or when the NickelMetal Hydride batteries have not been used for a long time, they may not fully charge. This is typical of this type of battery, and is not a malfunction. If this happens, repeatedly using up the battery fully, and then recharging it, should correct the problem. · Even when Nickel-Metal Hydride batteries are not being used they loose their charge naturally over time. It is recommended that you recharge the batteries just before using them. · If you recharge Nickel-Metal Hydride batteries before fully using up the existing charge, the so-called memory effect* can occur, and the low battery warning will be triggered sooner than expected. Charging the battery after fully depleting the existing charge should correct the problem. * The "memory effect" the situation in which a battery temporarily accepts a less than full charge.
· To use up the batteries completely, put the camera in the slide show mode (page 63) and leave it that way until the batteries are used up. · Do not peel off the external seals or damage the batteries. Never use batteries from which the seals have been partially or completely removed, or batteries that have been split in any way. These may cause leakage, explosion, or heat-up of the battery, and personal scald or injury may be caused. These may cause a malfunction of the battery charger.
15
Getting started
Inserting the batteries
2 1 2 1
1
, Open the battery cover.
Slide it in the direction of the arrow with the OPEN button pressed, and it opens out.
2
, Insert the batteries.
Match the +/- poles of the batteries to the +/ - marks inside the battery case.
· Occasionally clean the poles of the batteries and the terminals of the battery cover by wiping them with a dry cloth. If the poles of the batteries or the terminals become covered with a film of dirt or oil from the skin, the operating time of the camera can be greatly reduced.
3
, Close the battery cover.
Close the battery cover while holding the batteries in. The cover is closed when it clicks. To remove the batteries Stand the camera on end, open the battery cover upward, then remove the batteries.
· Make sure you do not drop the batteries when opening or closing the battery cover.
16
Battery remaining indicator (When using the Nickel-Metal Hydride batteries)
As the battery power decreases with use, the battery remaining indicator displays the amount of power remaining using the following symbols.
Battery Battery remaining remaining guidelines indicator (A full charge is 100%) Sufficient power remaining Battery half full Battery low, recording/ playback will stop soon. Change the batteries for fully charged ones, or charge these batteries. (The warning indicator flashes.)
· If the LCD screen is off, press to turn it on. · Based on the conditions under which the camera is being used and the state of the charge, or on the environment, this information may not be correctly indicated. · When the AC Adaptor (not supplied) is being used, the remaining battery information is not displayed.
The Power Save function
When the Power Save function is set to On, you can shoot for a longer period of time. Turn the mode selector to SET UP, and set [Power Save] in Setup 1 to [On]. The factory setting of the camera is set to [On] (page 107). We recommend that you set [Power Save] to [On] when using alkaline batteries. When the Power Save function is On
· In shooting still images, the focus only focuses when the shutter is pushed down halfway. · While charging the flash, the lamp flashes and the LCD screen is turned off. After the flash is completely charged, the LCD screen turns on.
Battery life and the number of images that can be recorded/ played back
The tables show approximate guidelines for the length of time the camera can be used when you shoot in Normal mode in an environment where the ambient temperature is 25°C (77°F), and the batteries are fully charged. The guidelines for the number of images that can be recorded or played back allow for changing the supplied "Memory Stick" as necessary. Actual results may differ slightly from these, depending on the conditions of use.
Getting started
Shooting still images Under the average conditions1)
NH-AA-DA (2) (supplied) Image LCD No. of Battery size screen images life (min.) DSC-P72 On Approx. 300 Approx. 150 3.1M Off Approx. 500 Approx. 250 On Approx. 300 Approx. 150 VGA Off Approx. 500 Approx. 250 DSC-P52 On Approx. 320 Approx. 160 3.1M Off Approx. 540 Approx. 270 On Approx. 320 Approx. 160 VGA Off Approx. 540 Approx. 270 DSC-P32 On Approx. 320 Approx. 160 3.1M Off Approx. 540 Approx. 270 On Approx. 320 Approx. 160 VGA Off Approx. 540 Approx. 270
17
Inserting the batteries (continued)
R6 (Size AA) alkaline battery (2) (not supplied) Image LCD No. of Battery size screen images life (min.) DSC-P72 On Approx. 70 Approx. 35 3.1M Off Approx. 130 Approx. 65 On Approx. 70 Approx. 35 VGA Off Approx. 130 Approx. 65 DSC-P52 On Approx. 80 Approx. 40 3.1M Off Approx. 140 Approx. 70 On Approx. 80 Approx. 40 VGA Off Approx. 140 Approx. 70 DSC-P32 On Approx. 80 Approx. 40 3.1M Off Approx. 140 Approx. 70 On Approx. 80 Approx. 40 VGA Off Approx. 140 Approx. 70
When using Sony alkaline batteries
1)
Playing back2) still images
NH-AA-DA (2) (supplied) No. of Image size images DSC-P72 3.1M VGA DSC-P52 3.1M VGA DSC-P32 3.1M VGA
2)
Battery life (min.)
Approx. 5400 Approx. 270 Approx. 5400 Approx. 270 Approx. 6000 Approx. 300 Approx. 6000 Approx. 300 Approx. 6000 Approx. 300 Approx. 6000 Approx. 300
· The battery life and the number of images recordable decrease under the following conditions: At low temperatures. Using the flash. Turning the camera on and off frequently. Using the zoom heavily (DSC-P72/P52 only) When [LCD Backlight] is set to [Bright]. When [Power Save] is set to [Off]. After using the batteries repeatedly over a long period of time or after often allowing it to self-discharge after charging (page 110).
Showing single images in order, one approximately every three seconds
Shooting3) movies
NH-AA-DA (2) (supplied) LCD LCD screen screen On Off DSC-P72 DSC-P52 DSC-P32
3)
Shooting under the following conditions: The image quality is set to [Fine]. Shooting one image every 30 seconds. Alternatively pressing the zoom W and T buttons fully for each shot (DSC-P72/P52 only). Using the flash once in every two shots. Turning on and off once in every ten shots.
Approx. 160 Approx. 160 Approx. 160
Approx. 210 Approx. 210 Approx. 210
Continuous shooting with a picture size of 160 (Mail)
18
Using an external power source
AC Adaptor (not supplied) 2 To a wall outlet (wall socket)
Using your camera abroad
Power sources You can use your camera in any country or area with the supplied battery charger or AC Adaptor (not supplied) within 100 V to 240 V AC, 50/60 Hz. Use a commercially available AC plug adaptor [a], if necessary, depending on the design of the wall outlet (wall socket) [b].
BC-CS2A/CS2B
Getting started
DC plug
1 Jack cover Power cord (mains lead)
1
, Open the jack cover, then connect the AC-LS5 AC Adaptor (not supplied) to the DC IN jack of the camera.
Connect the plug with the v mark facing toward the LCD screen.
· Be sure to use the AC-LS5 AC Adaptor. Other AC adaptors cannot be used with this camera. · Connect the AC Adaptor to an easily accessible wall outlet (wall socket) close by. If some trouble occurs while using the adaptor, immediately shut off the power by disconnecting the plug from the wall outlet (wall socket).
2
, Connect the power cord (mains lead) to the AC Adaptor and to a wall outlet (wall socket).
· When you have finished using the AC Adaptor, disconnect it from the DC IN jack of the camera. · The set is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet (wall socket), even if the unit itself has been turned off. · Do not use an electrical transformer (travel converter), as this may cause a malfunction.
19
Turning your camera on/off
POWER lamp
POWER
How to use the control button
The Auto Power Off function
POWER
, Press POWER to turn on the camera.
The POWER lamp lights in green and the power is on. When you turn on the camera for the first time, the Clock Set screen appears (page 21). To turn off the power Press POWER again, the POWER lamp goes out, and the camera turns off.
· Do not remove the batteries or AC Adaptor with the lens portion pulled out. This may cause a malfunction (DSC-P72 only). · When you turn the power on with the mode selector set to or , the lens begins to move (DSC-P72 only). Please be careful not to touch the lens.
If no tasks are performed for a while* when shooting, viewing images, or setting up the camera while using the batteries, power is automatically shut off to preserve battery power. However, in the following circumstances, even if the batteries are being used to power the camera, the Auto Power Off function will not work. · Movies are being played back · A slide show is being shown · A cable is connected to the (USB) jack or the A/V OUT (MONO) jack * When [Power Save] is set to [On]: approximately 90 seconds When [Power Save] is set to [Off]: approximately three minutes
Program Auto Camera
Mode
Voice E-Mail Burst 2 Normal REC Mode
To change the current settings of the camera, bring up the menu or the SET UP screen (page 45), and use the control button to make the changes. For each item, press v/V/b/B to select the desired value, then press z or b/B to make the setting.
20
Setting the date and time
Mode selector
POWER
Clock Set
Y/M/D M/D/Y D/M/Y
Getting started
Clock Set
Y/M/D M/D/Y D/M/Y
2003 / 1 / 1
OK
12 : 00
OK AM Cancel
2003 / 1 / 1
OK
12 : 00
OK AM Cancel
1
, Set the mode selector to .
· You can carry out this operation even when the mode selector is set to or . · To set the time and the date again, set the mode selector to SET UP, select [Clock Set] in (Setup 1) (pages 45, 107), then proceed from Step 3.
2
, Press POWER to turn on the camera.
The POWER lamp lights in green and the Clock Set screen appears on the LCD screen.
3
, Select the desired date format with v/V on the control button, then press z.
You can select from [Y/M/D] (year/month/ day), [M/D/Y], and [D/M/Y].
· If the rechargeable button battery, which provides the power for saving the time data, ever loses its charge (page 109), the Clock Set screen automatically reappears. If this happens, start from Step 3 to set up the date and time again.
21
Clock Set
Y/M/D M/D/Y D/M/Y
Clock Set
Y/M/D M/D/Y D/M/Y
Clock Set
Y/M/D M/D/Y D/M/Y
2003 / 1 / 1
OK
12 : 00
OK AM Cancel
2003 / 7 /
OK
4
12 : 00
OK AM Cancel
2003 / 7 / 4
OK
10 : 30
OK AM Cancel
4
, Select the year, month, day, hour, or minute item you want to set with b/B on the control button.
v is shown above and V is shown below the selected item.
5
, Set the desired numerical value with v/V on the control button, then press z.
After setting the current numerical value, set the next item. Repeat the above process until all of the items have been set.
· If you select [D/M/Y] in Step 3, set the time on a 24- hour cycle.
6
, Select [OK] with B on the control button, then press z.
The date and time are set and the clock will start to keep time.
· To cancel the setting process, select [Cancel], then press z.
22
Shooting still images
Inserting and removing a "Memory Stick"
Terminal side Access lamp
Label side
Shooting still images
1
, Open the "Memory Stick" cover.
Slide the cover in the direction of the arrow.
· For more information about the "Memory Stick," see page 109.
2
, Insert the "Memory Stick."
Insert the "Memory Stick" all the way in until it clicks as shown in the illustration.
· Whenever you insert a "Memory Stick," push it as far as it can go. If you do not insert it correctly, a proper recording or playback may not be carried out.
3
, Close the "Memory Stick" cover.
To remove the "Memory Stick" Open the "Memory Stick" cover, then push the "Memory Stick" to pop it out.
· Whenever the access lamp is lit, the camera is recording or reading out an image. Never remove the "Memory Stick" or turn off the power at this time. The data may be corrupted.
23
Setting the still image size
3.1M VGA
Mode selector
3.1M 2.8M(3:2) 2.0M 1.2M VGA Image Size 3.1M 2.8M(3:2) 2.0M 1.2M VGA Image Size
1
, Set the mode selector to .
2
, Turn on the camera, then press (Image Size).
The Image Size setup item appears.
· For more information about the image size, see page 25.
3
, Select the desired image size with v/V on the control button.
The image size is set. After the setting is completed, press (Image Size). The Image Size setup item disappears from the screen.
· The image size value selected here is preserved even when the camera is turned off.
24
Image size and quality
You can choose image size (number of pixels) and image quality (compression ratio) based on the kind of images you want to shoot. The larger you make the image size and the higher you make the image quality, the better your image, but also the larger the amount of data needed to preserve your image. This means you can save fewer images in your "Memory Stick." Choose an image size and quality level appropriately for the kind of images you want to shoot. You can resize the images later (Resize function, see page 69). You can choose an image size from among the five options in the following tables. The image sizes shown below show minimum settings as examples. When you want to improve image quality, select a larger image size.
Image size 3.1M 2048×1536 2.8M (3:2) 2048(3:2) 2.0M 1632×1224 1.2M 1280×960 VGA
1)
The number of images that can be saved in a "Memory Stick"2)
The number of images that can be saved in Fine (Standard)3) mode are shown below. (Units: number of images)
Capacity Image size 3.1M 2.8M (3:2) 2.0M 1.2M VGA
2) When
Shooting still images
16MB 10 (18) 10 (18) 16 (30) 24 (46) 97 (243)
32MB 20 (37) 20 (37) 33 (61) 50 (93) 196 (491)
64MB 41 (74) 41 (74) 66 (123) 101 (187)
128MB 82 (149) 82 (149) 133 (246) 202 (376)
MSX-256 MSX-512 MSX-1G 148 (264) 148 (264) 238 (446) 302 (537) 617 (1097) 302 (537) 617 (1097) 484 (907) 988 (1852) 1482 (2694) 5928 (14821)
357 (649) 726 (1320) 1428 (3571) 2904 (7261)
394 (985) 790 (1975)
[REC Mode] is set to [Normal] For the number of images that can be saved in other modes, see page 101. 3) For more information about the image quality mode, see page 46. · "3.2MEGA PIXELS" shown on the surface of the camera is the number of effective pixels of the CCD. However, the maximum number of pixels recorded is 3.1 mega pixels. · When the images recorded using other Sony devices are played back, the image size indication may be different from the actual image size.
640×480
Examples Printing A4 size images 3:2 prints1) Printing A5 size images Printing postcard size images Creating your home page
· When the images are viewed on the LCD screen of the camera, they all look the same size. · Number of shooting images can differ from these values according to shooting conditions. · When the remaining number of images recordable is more than 9999, ">9999" is indicated.
This option records images in a horizontal to vertical proportion of 3:2 to match the size of the print paper used.
25
Basic still image shooting using auto mode
VGA FINE 101
Mode selector
98
F2.8 30
1
, Set the mode selector to and turn on the camera. ,
2
, Hold the camera steadily with both hands and position a subject in the center of the focus frame.
Do not cover the lens, flash, or microphone with your fingers.
· The minimum focal distance to a subject is as follows: DSC-P72: 50 cm (19 3/4 inches) DSC-P52: 8 cm (3 1/4 inches) (W)/40 cm (15 3/4 inches) (T) DSC-P32: 10 cm (4 inches) To shoot subjects at distances closer than this, use the macro mode (DSC-P72 only) (page 30).
3
AE/AF lock indicator Flashes in green t Remains on
, Press and hold the shutter button halfway down.
The camera beeps. When the AE/AF lock indicator stops flashing and remains on, the camera is ready for shooting. (The screen may be frozen for a split second depending on the subject.)
· If you release your finger from the shutter button, shooting will be canceled. · When the camera does not beep, the AF adjustment is not complete. You can continue to shoot, but the focus is not set properly. · The frame indicated on the LCD screen shows the focus adjustment range. (AF range finder, see page 48.)
The recording folder name is indicated on the LCD screen for about five seconds.
· The lens cover opens when the power is turned on. · Do not touch the lens portion while it is operating, such as when you press POWER to turn on the power or when the zoom function is working (DSC-P72 only) (page 29). · You can create a new folder in the "Memory Stick" and select the folder for storing images (page 46).
26
VGA
101
97
The position on the mode selector
When the mode selector is set to , the functions that can be selected change according to the (Camera) setting in the menu settings as follows:
Twilight mode [ See page 58.
]
Twilight portratit mode [ See page 58. Landscape mode [ See page 58. Snow mode [ See page 58. ] ]
]
Shooting still images
4
, Press the shutter button fully down.
The shutter clicks, the shooting is completed, and the still image is saved in the "Memory Stick." When the recording lamp (pages 9, 11, 13) goes out, you can shoot the next image.
· When you are shooting with the batteries, if no tasks are performed for a while with the camera turned on, power is automatically shut off to preserve battery power (page 20).
Program Auto Camera Mode
Auto mode shooting [Auto] You can shoot your subject easily since this mode automatically adjusts the focus, exposure, and white balance. In this mode, [Mode] is set to [Fine], the AF range finder is set to [Multi AF], and the metering mode is set to multi-pattern metering (pages 48, 51). The menu items you can display are limited to (Camera) and [Mode] (REC Mode). Program mode shooting [Program] You can set the shooting functions in the menu settings according to your shooting condition.
Beach mode [ See page 58.
]
To change the camera mode
1 Set the mode selector to 2 Press MENU.
.
3 Select (Camera) with b on the control button. 4 Select the desired camera mode with v/ V on the control button.
27
Basic still image shooting using auto mode (continued)
Checking the last image shot
Quick Review
About Auto Focus
When you try to shoot a subject that is hard to focus on, the AE/AF lock indicator will change to flashing slowly. The Auto Focus function may be difficult to use with in the following subjects. In such cases, release the shutter button, then try to recompose the shot and focus again.
· The subject is distant from the camera and dark · The contrast between the subject and its background is poor · The subject is seen through glass, such as a window · A fast-moving subject · The subject has a reflection, such as that from a mirror, or there is a luminous body and a lustrous subject · A flashing subject. · A backlit subject
VGA
101
98
Review
101-0008
RETURN
2003 7 4 10:30PM
, Press b (7) on the control button.
To return to shooting mode, press the shutter button lightly or press b (7) on the control button again. To delete the image displayed on the LCD screen 1 Press (Delete). 2 Select [Delete] with v on the control button, then press z. The image is deleted.
There are two methods for Auto Focus function: Multipoint AF and Center AF (page 48). When [ ] (Camera) is set to [Auto] in the menu settings, the Multipoint AF is automatically selected.
28
Using the zoom feature
W (wide-angle) T (telephoto)
VGA
Smart zoom
You can zoom in on the image using a digital zoom process with no deterioration in the image quality. The maximum zoom scale depends on the image size.
DSC-P72 DSC-P52 DSC-P32 2.0M 1.2M VGA
Zoom scaling indicator The T side of this line shows the extent of smart zoom
101
VGA
101
98
98
x1.1
x5.0
Shooting still images
x2.5
3.8× 4.8× 9.6×
2.5× 3.2× 6.4×
1.3× 1.6× 3.2× DSC-P32 The DSC-P32 does not have an optical zoom. It has only the smart zoom.
· You cannot confirm the image using the finder when using the smart zoom function. · When using the smart zoom, the image on the LCD screen may look rough. However, this phenomenon has no effect on the recorded image. · AF range finder is not shown when using the smart zoom. When 9 (Focus) is set to [Multi AF] or [Center AF], or flashes and the centrally-located subject has priority to focus on.
, Press the zoom buttons to choose the desired zoom position, and shoot your image.
The minimum distance needed to focus on a subject Approximately 50 cm (19 3/4 inches) from the end of the lens (DSC-P72) Approximately 8 cm (3 1/4 inches) (W)/ 40 cm (15 3/4 inches) (T) from the end of the lens (DSC-P52) Approximately 10 cm (4 inches) from the end of the lens (DSC-P32)
· The lens moves when the zoom feature is being used (DSC-P72 only). Be very careful not to touch the lens. · You cannot change the zoom scaling while shooting movies (page 72).
When the image size is [3.1M] or [2.8M (3:2)], the smart zoom does not work. DSC-P72/DSC-P52 When the zoom exceeds 3× (DSC-P72) or 2× (DSC-P52), enlargement is carried out using the smart zoom. When the smart zoom is not needed, set [Smart Zoom] to [Off] in the SET UP settings (page 106). Pressing the zoom buttons displays the zoom scaling indicator on the LCD screen.
29
Shooting close-ups
Macro (DSC-P72 only)
VGA
101
VGA
FINE
101
98
97
1
For close-ups of small subjects like flowers or insects, shoot using the macro feature. You can use this feature for close-ups of subjects up to the distances specified below. When the zoom is set all the way to the W side: 10 cm (4 inches) from the end of the lens When the zoom is set all the way to the T side: 50 cm (19 3/4 inches) from the end of the lens
2
, Center the subject in the frame, and press the shutter button fully down.
To return to normal shooting Press B ( ) on the control button again. The indicator disappears from the LCD screen.
· Use the LCD screen to shoot when using the macro feature. If you use the finder, the limits of what you see and what you actually shoot may be different.
, Set the mode selector to , and press B ( ) on the control button.
The (Macro) indicator appears on the LCD screen.
· If the menu is currently displayed, press MENU first to make the menu disappear. · You can carry out this operation even when the mode selector is set to .
30
Using the self-timer
VGA
101
VGA FINE 101
98
98 F2.8 30
Shooting still images
1
, Set the mode selector to , and press V ( ) on the control button.
The (Self-timer) indicator appears on the LCD screen.
· If the menu is currently displayed, press MENU first to make the menu disappear. · You can carry out this operation even when the mode selector is set to .
2
, Center the subject in the frame, and press the shutter button fully down.
The Self-timer lamp (pages 8, 10, 12) will flash in orange, and you will hear a beeping sound. The image will be shot after approximately 10 seconds. To cancel the self-timer during the operation Press V ( ) on the control button again. The indicator dissapears from the LCD screen.
· If you stand in front of the camera and press the shutter button, the focus and the exposure may not be correctly set.
31
Selecting a flash mode
(No flash): The flash will not be used.
VGA
101
98
When shooting against a light source
In Auto mode, shooting against a light source automatically flashes even when there is enough light around the subject. (Daylight synchro) Before flashed
, Set the mode selector to , and press v ( ) on the control button repeatedly to select a flash mode.
The flash mode has the following features. No indicator (Auto): The camera decides to use the flash based on lighting conditions. The flash will be used when there is not enough light or when shooting a subject against a light source. (Forced flash): The flash will be used regardless of the amount of ambient light. (Slow synchro): The flash will be used regardless of the amount of ambient light. In this mode, the shutter speed is slower under dark conditions, so you can clearly shoot a background that is out of the flash-lit area.
· If the menu is currently displayed, press MENU first to make the menu disappear. · You can carry out this operation even when the mode selector is set to (Clip motion). · The recommended distance using the flash is as follows (when [ISO] is set to [Auto]): About 0.5 m to 3.8 m (19 3/4 inches to 12 feet 5 19/32 inches) (W)/0.5 m to 2.5 m (19 3/4 inches to 8 feet 2 7/16 inches) (T) (DSC-P72). About 0.5 m to 3.3 m (19 3/4 inches to 10 feet 9 29/32 inches) (DSC-P52). About 0.5 m to 3.8 m (19 3/4 inches to 12 feet 5 19/32 inches) (DSC-P32). · You can change the brightness of the flash using [Flash Level] in the menu settings (page 103). · Because the shutter speed is slower under dark conditions when (Slow synchro) or (No flash) is selected, it is recommended that you use a tripod. · While the flash is being charged, the lamp flashes. After charging is completed, the lamp goes out. · The flash mode selected here is preserved even when the camera is turned off.
When flashed
· The best performance may not be given depending on shooting conditions. · When you do not want to use the flash, set the flash mode to (No flash).
32
To reduce "red-eye" when shooting live subjects
The flash pre-strobes before shooting to reduce the red-eye phenomenon. Set [Red Eye Reduction] to [On] in the SET UP settings (page 106). appears on the LCD screen.
Shooting with the AF illuminator
This is additional lighting provided to assist in focusing when shooting in dark places. Set [AF Illuminator] to [Auto] in the SET UP settings (page 106). If you try to shoot under insufficient lighting conditions, ON appears on the LCD screen; the AF illuminator will emit a red light automatically during the time between when the shutter button is pressed halfway down and the focus locks.
VGA FINE 101
·
· ·
·
m
ON
98 F2.8 30
·
DSC-P32: Up to approximately 2.5 m (8 feet 2 7/16 inches) If AF illuminator light misses the center of the image somewhat, the camera will focus properly as long as it reaches the subject. When the focus preset distance is set (page 49), the AF illuminator does not function. When 9 (Focus) is set to [Multi AF] or [Center AF], the AF range finder is not displayed. or flashes and the centrallylocated subject has priority to focus on. When [ ] (Camera) is set to one of the following items in the menu settings, the AF illuminator will not function (page 58). When shooting in Twilight mode When shooting in Landscape mode The AF illuminator is a bright light. There are no safety hazards, but when shooting at short distances, do not aim it directly at the subject's eyes.
Shooting still images
· The amount of red-eye reduction possible varies according to the individual. In addition, the distance to the subject, and whether or not the subject has seen pre-strobe light begin to strobe may also reduce the effectiveness of the red-eye reduction process.
· Even when the AF illuminator flashes, but sufficient light does not reach the subject*, or the subject has weak contrast, the camera may not focus properly. * The recommend distance for this feature is as follows: DSC-P72: Up to approximately 3.8 m (12 feet 5 19/32 inches) (W)/Up to approximately 2.5 m (8 feet 2 7/16 inches) (T) DSC-P52: Up to approximately 3.3 m (10 feet 9 29/32 inches)
33
Shooting with the finder
All of the indicators are turned off Finder · This setting is maintained even when the power is turned off.
r The LCD screen is turned off. r All of the available indicators are turned on.
VGA
101
The finder is convenient when you want to save battery power, or when it is difficult to confirm the image using the LCD screen. Each time you press , the display changes in the following order.
98
· The image through the finder does not indicate the actual recordable range. To confirm the recordable range, use the LCD screen. · For details on the items displayed, see page 113. · Just as with the AE/AF lock indicator on the LCD screen, when the AE/AF lock lamp of the finder section stops flashing and remains on, you can start shooting (page 26). · When the LCD screen is turned off, the smart zoom does not function (page 29). · If you press (Flash mode)/ (Self-timer)/ (Macro) (DSC-P72) or (Spot meter) (DSCP52/P32) with the LCD screen turned off, the image will be displayed on the screen for approximately two seconds so you can check or change the setting.
34
Inserting the date and time on a still image
Camera
Camera
Camera
Moving Image: Smart Zoom: Date/Time: Red Eye Reduction: AF Illuminator:
MPEG Movie On Off Off Auto
Moving Image: Smart Zoom: Date/Time: Red Eye Reduction: AF Illuminator:
Day&Time Date Off
Moving Image: Smart Zoom: Date/Time: Red Eye Reduction: AF Illuminator:
MPEG Movie On Date Off Auto
Shooting still images
SELECT
OK
PAGE SELECT
1
, Set the mode selector to SET UP.
The SET UP screen appears.
· When images are shot with the date and time inserted, the date and time cannot be removed later. · When shooting images with the date and time inserted, the actual date and time are not displayed on the LCD screen, and is displayed in the upper-left portion of the LCD screen instead. The actual date and time are indicated in red on the lower-right corner when the image is played back.
2
, Select (Camera) with v on the control button, then press B. Select [Date/Time] with v/V, then press B.
3
, Select the date and time setting with v/V on the control button, then press z.
Day&Time: Inserts the date and the time of shooting into the image Date: Inserts the year, the month and the date of shooting into the image Off: Does not insert date/time data into the image After the setting has been completed, set the mode selector to to shoot your image.
· When you chose [Date], the date will be inserted in the order set in "Setting the date and time" (page 21). · This setting is maintained even when the power is turned off.
35
Viewing still images
Viewing images on the LCD screen of your camera
Single (single-image) screen
VGA
Viewing on the single-image screen
VGA
Index (nine-image) screen
Index (triple-image) screen
101
8/9
101
8/9
Aperture Value: Shutter Speed: Exposure Value: ISO:
F2.8 1/30 0.0 100
BACK/NEXT
101-0008
BACK/NEXT
2003 7 4 10:30PM
VOLUME
101-0008
BACK/NEXT
2003 7 4 10:30PM
VOLUME
SINGLE DISPLAY
MOVE
101-0002
SINGLE DISPLAY
2003 7 4 10:30PM
1
, Set the mode selector to and turn on the camera. ,
You can view images shot with the camera almost immediately on the screen. You can select the following three methods for viewing images. Single (single-image) screen You can view one image at a time, occupying the entire screen. Index (nine-image) screen Nine images are displayed simultaneously in separate panels on the screen. Index (triple-image) screen Three images are displayed simultaneously in separate panels on the screen. Various image information items are also displayed.
· For details on the movies, see page 73. · For a detailed description of the screen indicators, see page 115.
The newest image in the selecte