Text preview for : onkyo DPC-5.2.pdf part of onkyo dpc-5.2 onkyo dpc-5.2 service manual
Back to : onkyo DPC-5.2.part1.rar | Home
DPC-5.2
Ref. No. 3705
SERVICE MANUAL
Schematic diagram & Printed circuit board view only
Nov, 2001
DVD CHANGER MODEL DPC-5.2
RC-472DV
Black model BMDD 120V AC, 60Hz
SAFETY-RELATED COMPONENT WARNING!!
THE MARK FOUND ON SOME COMPONENT PARTS INDICATES THE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. WHEN REPLACING, BE SURE TO USE PARTS OF IDENTICAL DESIGNATION. MAKE LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.
www.denom.com
DPC-5.2 SERVICE NOTE
PRECAUTIONS
1. Ground for the work-desk. Place a conductive sheet such as a sheet of copper (with impedance lower than 10Mohm) on the work-desk and place the set on the conductive sheet so that the chassis. 2. Grounding for the test equipments and tools. Test equipments and toolings should be grounded in order that their ground level is the same the ground of the power source. 3. Grounding for the human body. Be sure to put on a wrist-strap for grounding whose other end is grounded. Be particularly careful when the workers wear synthetic fiber clothes, or air is dry. 4. Select a soldering iron that permits no leakage and have the tip of the iron well-grounded. 5. Do not check the laser diode terminals with the probe of a circuit tester or oscilloscope. 1. Replacing the fuses
This symbol located near the fuse indicates that the fuse used is show operating type, For continued protection against fire hazard, replace with same type fuse , For fuse rating, refer to the marking adjust to the symbol. Ce symbole indique que le fusible utilise est e lent. Pour une protection permanente, n'utiliser que des fusibles de meme type. Ce demier est indique la qu le present symbol est apposre. REF.NO. F1 PART NO. 252159 DESCRIPTION 2A-UL/T-237
2. Safety-check out
(Only U.S.A. model) After correcting the original service problem perform the following safety check before releasing the set to the customer Connect the insulating-resistance tester between the plug of power supply cord and terminal GND on the back panel. Specifications: More than 10M ohm at 500V
LASER CAUTION
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION :
ATTENTION : POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LA PLUS LARGE DA LA FICHE DANS LA BORNE CORRESPONDANTE DA LA PRISE ET POUSSER JUSQU' AU FOND.
Initialization of setup
1. Press the "DISC 4" and "CDPLAY" key to the same timing. The "DISC 4 key is pushed previously. Then, light off the FL tube. 2. Push the power switch.
www.denom.com
DPC-5.2 SPECIFICATIONS
DVD Changer
Power supply Power consumption Weight External dimensions Signal system Frequency range (digital audio) Signal-to-noise ratio (digital audio) Audio dynamic range (digital audio) Harmonic distortion (digital audio) Wow and flutter Operating conditions AC 120 V, 60 Hz 20 W 15.0 lbs 17 1/8" x 5 1/16" x 16 15/16" (W/H/D) NTSC 48 kHz sampling 4 Hz to 22 kHz 96 kHz sampling 4 Hz to 42 kHz More than 98 dB More than 95 dB Less than 0.005 % Below measurable level Temperature: 41 F to 95 F, Operation status: Horizontal
Outputs
Video output S-video output Component video output Audio output (digital output Optical) Audio output (digital output Coaxial) Audio output (analog output) 1.0 V (p-p), 75 ohm , negative sync., pin jack (Y) 1.0 V (p-p), 75 ohm , negative sync. (C) 0.286 V (p-p), 75 ohm , Mini DIN 4-pin 1 1 1
(Y) 1.0 V (p-p), 75 ohm , negative sync., pin jack (PB)/(PR) 0.7 V (p-p), 75 ohm, pin jack 2 Optical connecter 1 1 2 0.5 V (p-p), 75 ohm , pin jack
2.0 V (rms), 320 ohm , pin jack (L, R)
Specifications and features are subject to change without notice.
www.denom.com
DPC-5.2
A B C D E
EXPLODEDVIEW CHASSIS
S2
S1
1
S2 H45 S3 S6
S1 S2 H52 H37 S1 H50 S3 H38 S1 S2 H26 S2 S2 S3 U2 S2 S2 H26 CC202 S2 H26 S2 H27 H27 S2 S2 CC201 H47 H21 H49 H23 S2 U3
CN 01
H35 H34 S3
S6
2
H41 S6 S2 H44 S6 F1 S2 S2 H8 H7 U2 H6 H53 H5 H10 S4 H47
FL tub e
H46 H52 H47
S2 H24 U1
S2 H43
S2
S2 S2 S2
H12
3
H4 S5
S4
H53 H47 S2 H22 S2 H48 H47 S2 S4 S2 U2 S2 S2 H27 U2 S2 H22 S2 H47 H42 S2
H2
H3
H20
H42
S2 H1
H15 H14 S5 H13
DPC-5.2
4
www.denom.com
DPC-5.2 EXPLODED VIEW PARTS LIST
EXPLODED VIEW PARTS LIST
NO H1 H2 H3 H4 H5 H6 H7 H8 H10 H12 H13 H14 H15 H20 H21 H22 H23 H24 H26 H27 H35 H37 PARTS No 55221510 55184480 55223420 55204210 55186710 55204250 55244620 55184600 55244670 55164930 55204180 55204260 55244680 55236110 55201610 55125120 55196510 55174580 55186640 55178960 55222240 55204300 NO DESCRIPTION Badge, DVD H38 Drawer panel H41 Clear plate H43 Logo badge, INTEGRA H44 Holder H45 Standby button H46 Power button H46 Shaft H47 Button CD PLAY H48 FL Holder H49 Font panel H50 Button OPEN/CLOSE H52 Button, 9 Keys H53 Front chassis U1 Rubber spacer 14.5 x 14.5 x 22 U2 Leg Sponge, chassis 15 x 16 x 30 U3 Bracket ground U4 Bracket, main board Spring, finger Power cord Rear panel PARTS No 55174610 55186600 55184690 55202510 55186670 55186680 55174680 55174550 55186620 55190690 55222010 55222020 55259110 55203110 55203100 DESCRIPTION Bracket R small Top cover Power supply board unit Shield cover Bracket L frame Bracket R frame Bracket roulette R Cushion, 12 x 8 x 20 Main chassis Rubber sheet, down load AC Inlet terminal Bracket, AC inlet Cover, Standby button Main circuit PC board assy Display PC board assy ( Included Standby LED PCB +Connection PCB + Open/ Close switch PCB +Inlet terminal PCB) Output terminal PC board assy Mechanism PC board assy (Included sensor PCB +roulette motor PCB)
55203120 55186040
NOTE: THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE ONLY WITH PART NUMBER SPECIFIED.
www.denom.com
DPC 5.2 DPC-5 2
M18
20710180 GEAR
pp-6.max
www.denom.com
DPC-5.2 DPC 2
M18
20710180
GEAR
pp-7.max
www.denom.com
DPC-5.2
A B C D E F G H
BLOCK DIAGRAM
1
AC120V 60Hz
CN701 RS-232 JACK
2
POWER SUPPLY UNIT 3
+12V ANALOG VCC +8V ANALOG VCC -8V ANALOG VCC +5V DIGITAL VCC +3.3V DIGITAL VCC +8V MOTOR VCC +12V MOTOR VCC 5V DISPLAY
IC201 STI5519 MPEG
L-CH MIXD
MUTE
R-CH MIXD
CVBS-VIDEO
S-VIDEO
JK804 RCA 3V
4
TVM MECHA F/E & MECHA
5
www.denom.com
DPC-5.2
A B C D E
SCHEMATIC DIAGRAM
Output terminal PC board 1
From Main PC board
OPTICAL
COAXIAL
2
Video output
From Main PC board
3
4
www.denom.com
RS-232C connector
Component
DPC-5.2
A B Main circuit PC board C D
SCHEMATIC
DIAGRAM 1
To Down load JIG
2
3
4
www.denom.com
To Mecha. control PC board
5
From Display PC board
From Pick up
DPC-5.2
A B C D
SCHEMATIC DIAGRAM
1
To Down load JIG
2
3
4
5
www.denom.com
DPC-5.2
A B C D E F
From Power supply unit
G
H
SCHEMATIC DIAGRAM
Display circuit PC board
1
Connection board
GRID(00:11)
2
Standby LED PC board
3
4
Open/Close PC board
5
www.denom.com
DPC-5.2
A B C D E
SCHEMATIC DIAGRAM Mechanism circuit PC board
1
2
3
To Mecha. control PC board
To Main control PC board CN206
4
To P003
Roulette motor PC board
www.denom.com
DPC-5.2
A B C D E
PC BOARD CONNECTION DIAGRAM
AC 120V 60Hz
1 Main circuit PC board
B08
2
Power supply circuit PC board
DVD Mecha. F/E PC board
Output terminal PC board
Power switch
Connection PC board
Mechanism control PC board
MOTOR
3
Standby switch PC board
CP904 CN904
OPEN/ CLOSE switch PC board
Display circuit PC board
DPC-5.2
4
www.denom.com
DPC-5.2 PRINTED CIRCUIT BOARD PARTS LIST
Display PC board assy (PART NO. 55203100)
CIRCUIT NO. PART NO. ICs IC901 55183040NR IC902 55191090NR Transistor Q901 5513318092 Remote sensor RM901 55156010NR FL tube FL901 55183030NR Diodes D904 7043654016 D905 55125510NR D906 5517787088 Coils L901 1403936091 L902,L905 1032875091 L903,L904 2053866091 L909,L912, 5512667050 L913,L914 Resonator X901 55126140NR Socket AS CN901 55191010NR CN902 55182990NR CN903 55199600NR CN904, 55123320 CN905 CN906 55199610NR Socket CP903 55090070 CP906 55123310 DESCRIPTION CXP82324 KIA7045 DTC114YKA NJL63H38 HNA-12SM17 1N4148 LED RB501V-40 22uH, Chip 0 ohm, Chip 4.7 ohm, Chip Choke CIRCUIT NO. C901 C903-C905, C908,C911 C906 C907 C909 PART NO. Capacitors 2034206030 2028804091 DESCRIPTION 47uF,+/-20%, 16V, Elect 0.1uF, +80-0%,Chip
2025205030 100uF,+/-20%, 6.3V, Elect 2026862041 470uF,+/-20%, 6.3V, Elect 2026884030 1uF,+/-20%, 50V, Elect Switches SW901,SW903, 55145270NR SW905,SW907, SW911,SW913, SW915,SW917, SW921,SW924, SW927,SW930, SW931 Spring FINGE 55178960 Finger type
10MHz
2.0MM 5 MA ST
www.denom.com
DPC-5.2 PRINTED CIRCUIT BOARD PARTS LIST
MAIN CIRCUIT PC BOARD ASSY (PART NO. 55203110)
CIRCUIT NO. IC201 IC202 IC301 IC302 IC303 IC401 IC501 IC21P Q201-Q203 Q220B,Q220C, Q220G,Q220R, Q220S,Q220Y Q221B,Q221C, Q221G,Q221R, Q221S,Q221Y Q301 Q301L,Q301R Q302L,Q302R L201-L203, L209, L204-L206, L210,R415, L501 L208 L211,L301 L220B,L220C, L220G,L220R, L220S,L220Y L302 X501 PART NO. ICs 55130350NR 20940740NR 55156290NR 55156030NR 55128990NR 55177660NR 55133310NR 20361320NR Transistors 2097046092 5513869056 DESCRIPTION STI55, Video processor M24C02WM, EEPROM HY57V65162, DRAM PCM1748 KE, D/A converter BA4560F, Ope. Amp. SST39V, Flash memory M74HCU04M 7806AP, Regulator KTC3875Y KTN2907A PART NO. Capacitors C201P,C204,C206, 2026894030 C210,C221,C232, C311,C406 C220B,C220C, 2025267030 C220G,C220Y, C220R,C220S C223B,C223C, 2025265030 C223G,C223R, C223S,C223Y C228-C230, 2026783030 C301L,C301R, C305L,C305R, C306L,C306R, C323 C233 2026862030 C325 C331 20269180AM C327 5513871092 KTD1304 C505 5513318092 5503943091 5513319092 Coils 1404174091 5512667050 DTC114YKA DTC323TK DTA114YKA C302L,C302R C221B,C221C, C221G,C221R, C221S,C221Y C501 C215,C217,C218, C222B,C222C, C222G,C222R, C222S,C222Y, C225,C234,C235, C504 C502,C503 C321 C237,C238, C239,C240, C241,C307L, C307R 2026862030 1013862091 1013867091 1500213030 CIRCUIT NO. DESCRIPTION 100uF, +/-20%,10V, Elect 470uF, +/-20%,10V, Elect 220uF, +/-20%,16V, Elect 47uF, +/-20%,16V, Elect
47uF, +/-20%,6.3V, Elect 1uF, +/-20%,6.3V, Elect 10uF, +/-20%,16V, Elect 470uF, +/-20%,6.3V, Elect 2200pF, +/-10%, Chip 3300pF, +/-10%, Chip 20pF, +/-5%, Chip 0.1uF, +80/-0%, Chip
Choke, 1uF
1037509091 2028804091
1032875091 5512671050 1404175091
Choke, 2.7uF
2050652091 2050654091 2050659091
1404174091 Resonator 55128980NR
Choke, 2.2uF
22pF, +/-5%, Chip 10pF, +/-0.5pF, Chip 100pF, +/-5%, Chip
www.denom.com
DPC-5.2 PRINTED CIRCUIT BOARD PARTS LIST
OUTPUT TERMINAL PC BOARD ASSY (PART NO. 55203120)
CIRCUIT NO. IC701 IC805 Q801 Q802 L801,L802, L803 JK801 JK802 JK803 JK804 CN01 CN701 D711 C701-C703, C706,C707 C705 C802 C820-C822, C825 C823,C824 PART NO. ICs 55197900NR 55164740NR Transistors 2097046092 2097048092 Coils 5512662050 Terminals 55164750XX 55175260XX 55191220XX 55149420XX Socket 55124610XX Connector 67472300XX Diode 7043654016 Capacitors 2026884030 2025205030 2026783030 2026862030 2025265030 DESCRIPTION uPD4721, RS-232 GP1F32T, Optical KTC3875Y KTA1504Y MT1, Choke Coaxial out RCA-2P out RCA-1P out Component out 1.25mm 21P RS-232, 87204-606 1N4148 1uF, +20-80%, 50V, Elect 100uF, +20-80%, 6.3V, Elect 47uF, +20-80%, 16V, Elect 470uF, +20-80%, 6.3V, Elect 220uF, +20-80%, 16V, Elect
www.denom.com
PC-5.2 PARTS LIST
Mechanism control PC board assy (PART NO. 55183130)
CIRCUIT NO. IC001,IC002 D001,D002 PI001-PI003 PI004 L001 C001,C003 C002,C004 C005 P003 P027 P406 R001,R002 R003,R004 PART NO. ICs 20656300NR Diodes 2041428001 Photo diodes 20586840NR 20556130NR Coil 20265120NR Capacitors 8043459071 20246950AF 20268030AM Socket 20504010XX 20713500NR 55183020NR Resistors 5088295016 2054943001 DESCRIPTION LB1641 1N5232B, 5.6V, Zener ITR9606/F2 GP2S28 20M LF 39U0H +10% 130M 22pF,+/-5%, Ceramic (CH) 0.1uF,+/-10%, Ceramic 1000uF,+/-20%, 25V, Elect 2.0MM 6 MA ST 06187F 100 ohm, +/-5%, 1/6W 2.2 ohm, +/-5%, 1/2W
www.denom.com
DPC-5.2 PRINTED CIRCUIT BOARD PARTS LIST
MAIN CIRCUIT PC BOARD ASSY (PART NO. 55203110)
CIRCUIT NO. D301 D303 CC201 CC202 CN201 CN205 CN207 CN206 CP201 CP202 CP203 CP205 PART NO. Diodes 5517107050 2049651091 Flat cables 55191150NR 55182940NR Socket AS 55182960NR 55182970NR 55199620NR Socket 55123450 55124680 55125910NR 55125910NR 55124600 DESCRIPTION UDZ 2.2 B, Zener 1SS355 19X 1.2 19X 1.2 CIRCUIT NO. C216 C303L,C303R C224B,C224C, C224G,C224R, C224S,C224Y, C225B,C225C, C225G,C225R, C225S,C225Y C203,C205,C209, C220 C211-C214, C242-C245, C328,C329 C322,C324,C326 C404,C405 PART NO. 2050668091 2067807091 2099397091 DESCRIPTION 470pF, +/-5%, Chip 330pF, +/-5%, Chip 390pF, +/-5%, Chip
1013896091 2050654091
0.01uF +/-10%,Chip 10pF +/-0.5pF, Chip
2.0MM 12 MA R 1.25MM 19 FE 1.0MM 15 FE S 1.0MM 15 FE S 1.25MM 19 FE
1013839091 1013855091 Spring 55178960
560pF +/-10pF, Chip 1000pF +/-10%, Chip Finger
www.denom.com
DPC-5.2 PANEL VIEW
FL DISPLAY
1 2 3 4 5 6 7 8 9 10 11 12
13
14
15 9 MEM. indicator
Illuminates during memory playback.
1 Inserted disc indicators
Indicate the type of current disc that is loaded.
2 Play/Pause indicators
Illuminate in play or pause mode.
10 PBC indicator
Illuminates when PBC is on for Video CD.
3 Parental Lock indicator
Illuminates in parental lock mode.
11 INTRO indicator
Illuminates during intro-scan playback.
4 TITLE indicator
Illuminates to indicate the current title number.
12 Elapsed time indicators
Indicate playing time.
5 RESUME indicator
Illuminates when the player is ready for resume playback.
13 Search indicators
Illuminate during search and slow playback mode.
6 CHPTER/TRACK indicators
Indicate display mode of the current chapter of DVD disc or track number of Video CD or CD.
14 Disc number indicator/CD indicator
Disc number indicators indicate the presence of a disc. CD indicator illuminates when the DVD Changer is in CD Play mode.
7 RANDOM indicator
Illuminates during random playback.
15 Multifunction indicator
Indicates operating status, messages, etc.
8 REPEAT indicators
Illuminate during repeat playback.
www.denom.com
DPC-5.2
A B C D E
PRINTED CIRCUIT BOARD VIEW
Main circuit board
1
Top pattern and top parts
2
3
DPC-5.2
4
www.denom.com
DPC-5.2
A B C D E
PRINTED CIRCUIT BOARD VIEW
Main circuit board
1
Bottom pattern and bottom parts
2
3
DPC-5.2
4
www.denom.com
DPC-5.2
A B C D E
PRINTED CIRCUIT BOARD VIEW Output terminal PC board
1
107NC
2
Component side view
3
Soldering side view
DPC-5.2
4
www.denom.com
DPC-5.2
A B C D E
PRINTED CIRCUIT BOARD VIEW
1
Display circuit PC board
2
Component side view
3
Soldering side view
4
www.denom.com
DV-C503
A B C D E
PRINTED CIRCUIT BOARD VIEW
Mechanism control PC board 1
300P 200C 81WJ 100CI 500C 300R 01WJ 02WJ 100C 100D 400R 300C 12WJ 6WJ 71WJ 31WJ 400P 41WJ
51WJ
100R 3WJ
200R 22WJ 400C
100L
200D 200CI 8WJ
7WJ
604P
2
Component side view
Roulette motor PC board
3
Component side view
DV-C503
4
www.denom.com
DPC-5.2 PRINTED CIRCUIT BOARD VIEW
Standby switch PC board
Open/Close switch PC board
309PC
ESOLC/NEPO 039WS
Component side view Soldering side view
Connection PC board
TESER.1 DxR.2 DxT.3 XUA/VT.4 S6V5+.5 GEPM oT TNORF oT TESER.1 DxR.2 DxT.3 XUA/VT.4 S6V5+.5
Soldering side view
409NC
Inlet PC board
Component side view
Component
www.denom.com
DPC-5.2
DISASSEMBLY PROCEDURE
Replacement of DVD mechanism
The laser diode in the optical pickup block so sensitive to static electricity, surge current and etc.. That the components are liable to be broken down or its reliability remarkable deteriorated. During repair, carefully take the following precautions. Do not touch the optical pickup object lens with the hands.
Short Land
1. Remove the top cover with six screws. 2. Remove the tray. 3. Remove the roulette assembly. 4. Remove the roulette. (Roulette is removed as written below.) 5. Solder the LD output lands on the DVD optical pickup. Please perform right photo to reference. 6. Replace the pickup mechanism assembly etc. . After unsolder the laser diodes output lands.
Remove the roulette
1. Pull out the tray. 2. Stops in the position (cut deeply). 3. Remove in the direction of arrow. 4. Reassembly is performed by 3 to 1.
Roulette
Cut deep
www.denom.com
DPC-5.2 PACKING VIEW
12 24 13 25 23 6 31 8 9
RC-472DV
10
7
5
DPC -5.2
30 22 29
UPC Label
DP
C-5
.2
e t sid ron F
5 A B C 5 5 D E F G
Continuation number: 4 Digit Factory No. Number of ten thousand digits Month code : JAN=1, OCT=X Year code Line classification
UPC
DV-C503 (B)
29363015
BAR-CODE (UPC) and the figure arefixed by model number
NOTE: THE COMPONENTS IDENTIFIED BY MARK ARE CRITICAL FOR RISK OF FIRE AND ELECTRIC SHOCK. REPLACE ONLY WITH PART NUMBER SPECIFIED.
7
51398 00448
3
Serial No.
PARTS LIST
NO 5 6 7 8 9 10 12 13 PARTS No 55204420 55184410 55184420 55204310 55020220NR 55176530 55204320 55186720 DESCRIPTION Carton box Pad Right Pad Left Remote controller RC-472DV Battery, UM-4 x 2 Audio/ Video connection cable Instruction manual Warranty card NO 22 23 24 25 29 30 31
5 A B C 5 5 D E F G
Serial No./ bar code (code 39)
PARTS No 55204330 55170660 55170650 20715540 55208740 29110141 55222240
DESCRIPTION UPC label Sheet, Set, 1150 x 1000 Poly bag,335 x240mm Poly bag, Power cord Cushion, 35sq x 80 PP tape Power cord
www.denom.com
DPC-5.2 UPGRADE THE FIRMWARE 1
a. The program for writing b. The program of binary form AAAABBB.bin Two files are saved to the same directory.
AAAA : model name BBB : Version
1. Jigs connection 1-1. PC-JIG Connect the D-Sub(25 pin) cable. 1.2. JIG-DPC-5.2 Connect the FFC and socket (down load PCB). 1.3. Remove a sheet at the bottom. Connect the socket (CP202). 1-4. Turn on the power switch of DPC-5.2. Light up the LED on the JIG PC board assy. 1-5. Start an MS-DOS window. (Click Strat, point to Programs, point to Accessories, Down load JIG and then click MS-DOS Prompt.) Part number 0P42 1-6. Input key the "dvd down AAAABBB.bin" and then click Return.
Main PC board assy (on the bottom side of DPC-5.2)
To Computer
CP202
1 15
Connect the grade up jig Part No. 0P42
c5.2
www.denom.com
DPC-5.2 UPGRADE THE FIRMWARE 2
1-7. Key input "Y". It is automatically written in in order of Identify, ROM ERASE, WRITE and Verify. Witting time are about 1 minute
c5.2
Writing was completed. 1-8. Press any key. 2. Confirmation of version of firmware 2-1. Press the "DIS 3" and "CDPLAY" key to the same timing. The "DISC 3" key is pushed previously. 2-2. Version number is displayed on FL tube. (wait several seconds )
71AAA BBCC
Creation day Creation month Version number ONKYO code
www.denom.com
DPC-5.2
Integra Division of ONKYO CORPORATION Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8111 Fax: 072-833-5222 http://www.onkyo.co.jp/ Integra Division of ONKYO U.S.A. CORPORATION 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 E-mail: [email protected] http://www.integrahometheater.com ONKYO EUROPE ELECTRONICS GmbH Industriestrasse 20, 82110 Germering, GERMANY Tel: 089-849-320 Fax: 089-849-3265 E-mail: [email protected] ONKYO CHINA LIMITED Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung, N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
PN 0Mxxxx D01xx Printed in Japan
www.denom.com