Text preview for : PS42P2SDX_XEC.0000040045.E.17.pdf part of Samsung PS42P2SDX/XEC PLASMA DISPLAY TV service manual
Back to : PS42.part1.rar | Home
Handling Description
9. Handling Description
9-1 Basic Description
9-1-1 The Name of Each Part
9-1-1(A) PDP(Plasma Disply Panel)
Front Panel
SPEAKER
SPEAKER
POWER
Press to turn the PDP on and off.
Remote Control Signal Receiver
Aim the remote control towards this spot on the PDP.
SOURCE
External input selection.
MENU
Menu display.
- VOLUME +
Volume adjustment.
SELECT
Control the cursor in the Menu.
MUTE
Temporary sound switch-off.
Samsung Electronics
9-1
Handling Description
Real Panel
a) External Speaker Outputs (8 )
Connect external speakers.
d) PC Input
Connect a PC signal from an PC.
b) S-VIDEO Input
Connect a S-Video signal from an S-VHS VCRs or DVD players.
e) SCART Audio/Video Input
Connect a audio/video signal from external sources like VCRs.
c) VIDEO Input
Connect a video signal from external sources like VCRs or DVD players.
f) Audio Inputs (Video/PC)
Connect a audio signal from external sources like VCRs or PC.
9-2
Samsung Electronics
Handling Description
9-1-1(B) REMOTE CONTROL
Filp the cover open in the arrow direction.
AUTOMATIC SWITCH-OFF VCR/DVD FUNCTIONS; (STOP/REWIND/PLAY/PAUSE/ FAST-FORWARD)
Power
POWER ON/OFF
PIP FUNCTIONS; PIP ON/SWAP/LOCATE/ SIZE SETTING/STILL/SCAN/ CHANNEL SELECTION(P / )/ MULTI DISPLAY/ INPUT SOURCE SELECTION (SOURCE)
NUMERIC BUTTONS
MAKE THE REMOTE CONTROL WORKS FOR MONITOR, VCR, CABLE, DVD PLAYER
EXTERNAL INPUT SELECTION
SELECT TO THE PC MODE DIRECTLY
TEMPORARY SOUND SWITCH OFF
MENU DISPLAY
CONTROL THE CURSOR IN THE MENU VOLUME DECREASE VOLUME INCREASE CHANGE CONFIRMATION
DISPLAYING INFORMATIONS
PICTURE SIZE SELECTION
STILL THE MAIN PICTURE
SOUND EFFECT SELECTION
PICTURE EFFECT SELECTION
Samsung Electronics
9-3
Handling Description
9-2 Wall Mount
9-2-1 Notice for installing
1. Do not install the PDP on any place other than veritical walls. 2. To protect the performance of the PDP and prevent problems, avoid the following place : G G G G Next to spring coloer detectors. Places subject to vibration or shock. Near high voltage cables. Around heating apparatus.
3. Install the PDP considering the construction of the wall. 4. Use only recommended parts and components for installation.
9-2-2 Parts(wall attachment panel is sold separately.)
Fixing bolt
Insulation rubber
9-4
Samsung Electronics
Handling Description
9-2-3 Installing the Display on the Wall Attachment Panel :
1. Check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to support the PDP, strengthen the wall before installation.
2. Fix the wall attachment panel on the wall using bolts as shown in the figure: Fixing bolts must protrude from the wall appox. 0.6 inches.
3. Using the wall attachment panel, you may adjust the angle of the display from 0 to 20 degrees. The angle can be set in 5 stages with 5 degrees of distance each using the angle control holes on the sides of the panel.
When the angle has been set to 5 degrees.
When the angle has been set to15 degrees.
When the panel hasn't been tilted.
Angle control holes
5 degrees of tilt 10 degrees of tilt 15 degrees of tilt No tilt 20 degrees of tilt
Samsung Electronics
9-5
Handling Description
4. Remove four large screws from the rear side of the display. Insert the bolts, dish-type washers, and insulation rubber into the four screw-holes as shown in the figure:
Bolt Insulation rubber
5. Put the insulation rubber point protruding from the rear top of the display in the groove on the top of the wall attachment panel. Lift up the display a little bit so that the insulation rubber point at the bottom of the rear side of the display is put to the groove at the bottom of the wall attachment panel. (Do not lift the display with any pressure. The insulation rubber at the top may be taken off.)v
9-6
Samsung Electronics
Handling Description
9-2-4 Separating the Display from the Wall Attachment Panel :
Remove the fixing bolts from both sides(left and right) of the wall attachment panel. Lift and pull thebottom of the display a small amount, to separate the insulation rubber point from the bottom of the wall attachment panel. Lift the display and separate the insulation rubber point from the groove on top of the wall attachment panel.
Samsung Electronics
9-7
MEMO
9-8
Samsung Electronics