Text preview for : 28C17A.pdf part of Catalyst Semiconductor CAT28C17A Datasheet: 16K-Bit CMOS PARALLEL E2PROM



Back to : 28C17A.pdf | Home

CAT28C17A
16K-Bit CMOS PARALLEL E2PROM FEATURES
s Fast Read Access Times: 200 ns s Low Power CMOS Dissipation: s End of Write Detection:

­Active: 25 mA Max. ­Standby: 100 µA Max.
s Simple Write Operation:

­DATA Polling DATA ­RDY/BSY Pin BSY
s Hardware Write Protection s CMOS and TTL Compatible I/O s 10,000 Program/Erase Cycles s 10 Year Data Retention s Commercial,Industrial and Automotive

­On-Chip Address and Data Latches ­Self-Timed Write Cycle with Auto-Clear
s Fast Write Cycle Time: 10ms Max

Temperature Ranges

DESCRIPTION
The CAT28C17A is a fast, low power, 5V-only CMOS parallel E2PROM organized as 2K x 8-bits. It requires a simple interface for in-system programming. On-chip address and data latches, self-timed write cycle with auto-clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and a RDY/BSY pin signal the start and end of the self-timed write cycle. Additionally, the CAT28C17A features hardware write protection. The CAT28C17A is manufactured using Catalyst's advanced CMOS floating gate technology. It is designed to endure 10,000 program/erase cycles and has a data retention of 10 years. The device is available in JEDEC approved 28-pin DIP and SOIC or 32-pin PLCC packages.

BLOCK DIAGRAM
A4­A10 ADDR. BUFFER & LATCHES INADVERTENT WRITE PROTECTION ROW DECODER 2,048 x 8 E2PROM ARRAY

VCC

HIGH VOLTAGE GENERATOR

CE OE WE

CONTROL LOGIC I/O BUFFERS TIMER DATA POLLING & RDY/BUSY I/O0­I/O7

A0­A3

ADDR. BUFFER & LATCHES

COLUMN DECODER

RDY/BUSY
5091 FHD F02

© 1998 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice

1

Doc. No. 25034-00 2/98

CAT28C17A

PIN CONFIGURATION
DIP Package (P)
RDY/BUSY NC A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC WE NC A8 A9 NC OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3

SOIC Package (J,K)
RDY/BUSY NC A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC WE NC A8 A9 NC OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 A6 A5 A4 A3 A2 A1 A0 NC I/O0 5 6 7 8

PLCC Package (N)
A7 NC RDY/BUSY

4 3 2 1 32 31 30 29 28 27 26 TOP VIEW 25 24 23 22 A8 A9 NC NC OE A10 CE I/O7 I/O6

9 10 11 12

13 21 14 15 16 17 18 19 20
I/O1 I/O2 VSS NC I/O3 I/O4 I/O5

PIN FUNCTIONS
Pin Name A0­A10 I/O0­I/O7 RDY/BUSY CE OE WE VCC VSS NC Function Address Inputs Data Inputs/Outputs Ready/BUSY Status Chip Enable Output Enable Write Enable 5V Supply Ground No Connect

NC VCC WE NC
5091 FHD F01

MODE SELECTION Mode Read Byte Write (WE Controlled) Byte Write (CE Controlled) Standby, and Write Inhibit Read and Write Inhibit H X CE L L L X H WE H OE L H H X H I/O DOUT DIN DIN High-Z High-Z Power ACTIVE ACTIVE ACTIVE STANDBY ACTIVE

CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5V Symbol CI/O(1) CIN(1) Test Input/Output Capacitance Input Capacitance Max. 10 6 Units pF pF Conditions VI/O = 0V VIN = 0V

Note: (1) This parameter is tested initially and after a design or process change that affects the parameter.

Doc. No. 25034-00 2/98

2

CAT28C17A

ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias ................. ­55°C to +125°C Storage Temperature ....................... ­65°C to +150°C Voltage on Any Pin with Respect to Ground(2) ........... ­2.0V to +VCC + 2.0V VCC with Respect to Ground ............... ­2.0V to +7.0V Package Power Dissipation Capability (Ta = 25°C) ................................... 1.0W Lead Soldering Temperature (10 secs) ............ 300°C Output Short Circuit Current(3) ........................ 100 mA RELIABILITY CHARACTERISTICS Symbol NEND(1) TDR(1) VZAP(1) ILTH(1)(4) Parameter Endurance Data Retention ESD Susceptibility Latch-Up Min. 10,000 10 2000 100 Max.

*COMMENT
Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability.

Units Cycles/Byte Years Volts mA

Test Method MIL-STD-883, Test Method 1033 MIL-STD-883, Test Method 1008 MIL-STD-883, Test Method 3015 JEDEC Standard 17

D.C. OPERATING CHARACTERISTICS VCC = 5V ±10%, unless otherwise specified. Limits Symbol ICC ICCC(5) ISB ISBC(6) ILI ILO VIH(6) VIL(5) VOH VOL VWI Parameter VCC Current (Operating, TTL) VCC Current (Operating, CMOS) VCC Current (Standby, TTL) VCC Current (Standby, CMOS) Input Leakage Current Output Leakage Current High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Write Inhibit Voltage 3.0 ­10 ­10 2 ­0.3 2.4 0.4 Min. Typ. Max. 35 25 1 100 10 10 VCC +0.3 0.8 Units mA mA mA µA µA µA V V V V V IOH = ­400µA IOL = 2.1mA Test Conditions CE = OE = VIL, f = 1/tRC min, All I/O's Open CE = OE = VILC, f = 1/tRC min, All I/O's Open CE = VIH, All I/O's Open CE = VIHC, All I/O's Open VIN = GND to VCC VOUT = GND to VCC, CE = VIH

Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) The minimum DC input voltage is ­0.5V. During transitions, inputs may undershoot to ­2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns. (3) Output shorted for no more than one second. No more than one output shorted at a time. (4) Latch-up protection is provided for stresses up to 100mA on address and data pins from ­1V to VCC +1V. (5) VILC = ­0.3V to +0.3V. (6) VIHC = VCC ­0.3V to VCC +0.3V.

3

Doc. No. 25034-00 2/98

CAT28C17A
A.C. CHARACTERISTICS, Read Cycle VCC = 5V ±10%, unless otherwise specified. 28C17A-20 Symbol tRC tCE tAA tOE tLZ(1) tOLZ(1) tHZ(1)(2) tOHZ(1)(2) tOH(1) Read Cycle Time CE Access Time Address Access Time OE Access Time CE Low to Active Output OE Low to Active Output CE High to High-Z Output OE High to High-Z Output Output Hold from Address Change 0 0 0 55 55 Parameter Min. 200 200 200 80 Max. Units ns ns ns ns ns ns ns ns ns

Figure 1. A.C. Testing Input/Output Waveform(3)
2.4 V INPUT PULSE LEVELS 0.45 V 0.8 V 2.0 V REFERENCE POINTS

5089 FHD F03

Figure 2. A.C. Testing Load Circuit (example)
1.3V 1N914

3.3K DEVICE UNDER TEST OUT CL = 100 pF

CL INCLUDES JIG CAPACITANCE
5089 FHD F04

Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) Output floating (High-Z) is defined as the state when the external data line is no longer driven by the output buffer. (3) Input rise and fall times (10% and 90%) < 10 ns.

Doc. No. 25034-00 2/98

4

CAT28C17A
A.C. CHARACTERISTICS, Write Cycle VCC = 5V ±10%, unless otherwise specified. 28C17A-20 Symbol tWC tAS tAH tCS tCH tCW(2) tOES tOEH tWP(2) tDS tDH tDL tINIT(1) tDB Write Cycle Time Address Setup Time Address Hold Time CE Setup Time CE Hold Time CE Pulse Time OE Setup Time OE Hold Time WE Pulse Width Data Setup Time Data Hold Time Data Latch Time Write Inhibit Period After Power-up Time to Device Busy 10 100 0 0 150 15 15 150 50 10 50 5 20 80 Parameter Min. Max. 10 Units ms ns ns ns ns ns ns ns ns ns ns ns ms ns

Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) A write pulse of less than 20ns duration will not initiate a write cycle.

5

Doc. No. 25034-00 2/98

CAT28C17A

DEVICE OPERATION
Read Data stored in the CAT28C17A is transferred to the data bus when WE is held high, and both OE and CE are held low. The data bus is set to a high impedance state when either CE or OE goes high. This 2-line control architecture can be used to eliminate bus contention in a system environment. Figure 3. Read Cycle
tRC ADDRESS tCE CE tOE OE VIH WE tLZ tOLZ DATA OUT HIGH-Z tOH DATA VALID tAA tOHZ tHZ DATA VALID
28C17A F05

Ready/BUSY (RDY/BUSY) The RDY/BUSY pin is an open drain output which indicates device status during programming. It is pulled low during the write cycle and released at the end of programming. Several devices may be OR-tied to the same RDY/BUSY line.

Figure 4. Byte Write Cycle [WE Controlled]
tWC ADDRESS tAS tCS CE tAH tCH

OE tOES WE tDL RDY/BUSY tDB DATA OUT HIGH-Z tWP tOEH

DATA IN

DATA VALID tDS tDH
5091 FHD F06

Doc. No. 25034-00 2/98

6

CAT28C17A
Byte Write A write cycle is executed when both CE and WE are low, and OE is high. Write cycles can be initiated using either WE or CE, with the address input being latched on the falling edge of WE or CE, whichever occurs last. Data, conversely, is latched on the rising edge of WE or CE, whichever occurs first. Once initiated, a byte write cycle automatically erases the addressed byte and the new data is written within 10 ms. Figure 5. Byte Write Cycle [CE Controlled]
ADDRESS tAS tAH tCW CE tOEH OE tCS WE tOES tCH tDL

DATA Polling DATA polling is provided to indicate the completion of a byte write cycle. Once a byte write cycle is initiated, attempting to read the last byte written will output the complement of that data on I/O7 (I/O0­I/O6 are indeterminate) until the programming cycle is complete. Upon completion of the self-timed byte write cycle, all I/O's will output true data during a read cycle.

tWC

RDY/BUSY tDB DATA OUT HIGH-Z

DATA IN

DATA VALID tDS tDH
5091 FHD F07

Figure 6. DATA Polling
ADDRESS

CE

WE tOEH OE tWC I/O7 DIN = X DOUT = X DOUT = X
28C17A F08

tOE

tOES

7

Doc. No. 25034-00 2/98

CAT28C17A
HARDWARE DATA PROTECTION The following is a list of hardware data protection features that are incorporated into the CAT28C17A. (1) VCC sense provides for write protection when VCC falls below 3.0V min. (2) A power on delay mechanism, tINIT (see AC characteristics), provides a 5 to 20 ms delay before a write sequence, after VCC has reached 3.0V min. (3) Write inhibit is activated by holding any one of OE low, CE high or WE high. (4) Noise pulses of less than 20 ns on the WE or CE inputs will not result in a write cycle.

ORDERING INFORMATION
Prefix CAT Device # 28C17A N Suffix I -20 T

Optional Company ID

Product Number

Temperature Range Blank = Commercial (0°C to +70°C) I = Industrial (-40°C to +85°C) A = Automotive (-40° to +105°C)* Package P: PDIP N: PLCC J: SOIC (JEDEC) K: SOIC (EIAJ)

Tape & Reel T: 500/Reel

Speed 20: 200ns

* -40°C to +125°C is available upon request

28C17A F09

Notes: (1) The device used in the above example is a CAT28C17ANI-20T (PLCC, Industrial temperature, 200 ns Access Time, Tape & Reel).

Doc. No. 25034-00 2/98

8