Text preview for : ve_avid_diva.pdf part of AVID ve avid diva . Rare and Ancient Equipment AVID Diva ve_avid_diva.pdf
Back to : ve_avid_diva.pdf | Home
ENGLISH
AVID
DIVA
TUR NTAB L E S Y S TE M
PLEASE FULLY READ THIS DOCUMENT BEFORE
ATTEMPTING TO ASSEMBLE YOUR NEW TURNTABLE
PACKAGING
Save all the packing in a dry place away from fire hazard. The DIVA Turntable is a precision instrument
and the packaging has been especially designed so that all component parts are safe during transportation.
We recommend that you do not transport with turntable assembled and never with the bearing fitted.
CONTENTS
Warnings 2
Mains Supply Frequency 2
Specifications 2
Box Contents and Drawings 3
Set-Up Instructions 4
Pick-Up Arm Adjustments 5
Suspension Installation and Adjustment 6
Drive System and Alignment 7
Motor/PSU Connections 8
PSU Operation 8
Clamp Operation 8
Power Supply Fuse 9
Cleaning 9
Warranty 9
----------------------------------------------------------------------------------------------------------------------------------------------
WARRANTY EXTENSION
Return slip with your details and you will sent our extended 5 year warrenty.
NAME:____________________________________________
ADDRESS:_________________________________________
__________________________________________________
S/N______ DEALER:__________PURCHASE DATE_______
Return to: AVID. Unit 52, 137 NorthGate, Alconbury Airfield, Huntingdon, Cambs. PE28 4WX ENGLAND
WARNINGS SPECIFICATIONS
Keep the Drive Belt, Pulley and Platter DRIVE : Belt Drive
free from contamination.
SPEEDS : 33 and 45 RPM
If the Drive Belt is dirty, replacement is
PLATTER MASS : 3.3Kg
required. It is not possible to clean.
Symptoms that the belt needs changing; BEARING : Inverted Stainless Steel, Tungsten/Sapphire Thrust
Speed instability and loss of dynamics.
SUSPENSION : 3 Point Variable Frequency Springs
Do not expose unit to rain or water. FREQUENCY : 4.5 Hz (Variable)
The Power Supply contains voltages that PICK-UP ARM : SME & REGA RB300 Arm Boards standard.
OPTIONS Adapters for REGA RB1000, Wilson Benesch,
can cause serious injury or death. There Dynavector, Triplanar & Graham available.
Different arm mountings to order.
are no user serviceable parts and no
reason to open. In situations of failure PICK-UP ARM : 9" Pick-Up Arms onto Standard arm/tube rods.
return to approved dealer or agent. VARIANTS 12" Pick-Up Arms onto Long arm/tube rods.
(When fitting 12" Arms it is recommended that
the Long Suspension Bars are used.)
Do not use or let liquid cleaners enter the
Power Supply. MOTOR : 24v AC Synchronous 50/60Hz
MAINS SUPPLY : Voltage and Frequency Specified on PSU rear.
The Platter surface may be cleaned with
normal glass cleaner. CONSUMPTION : 5 watts Max.
DIMENSIONS : Turntable 460 x 375 x 130mm
The Main Bearing contains a Sapphire Cup (W x H x D) : PSU 160 x 60 x 138mm
Jewel and this can be damaged if proper
care is not taken. This will effect or stop WEIGHT : 11.2Kg (Shipping 13.0Kg)
the turntable working correctly.
Improvements may result in specification or feature changes without notice.
Illustrations may differ slightly for production models.
MAINS SUPPLY FREQUENCY
Local electrical supply frequency is either 50Hz or 60Hz.
Regions with dual frequencies will be supplied with both
m)
drive pulleys so that the correct speed can be achieved. 5m
(65
m
0m
To change the drive pulley, remove screw with wrench 50
supplied and pull off pulley. Replace with correct pulley
and correctly align. Finally replace screw.
375mm (465mm)
Pulley DRIVE PULLEY ALIGNMENT
Screw Use inside of drive pulley for correct alignment
Spindle
Spindle top level with
inside of drive pulley
1.72mm Gap
Motor
! IF IN DOUBT CONTACT YOUR DEALER
460mm (600mm)
( ) Bracketed figures show maximum dimensions when using 2 x 12" arms and long Suspension Bars.
2
Box Contents and Drawings
Weight 1 Arm Board 1 Tools 5
Platter 1 Suspension Bars 3 Arm Rods & Tube 2/1
Drive Pulley
Another pulleys will be
included if specified or
needed in your region
Suspension Housings 3 Motor 1
Clamp 1 Drive Belt 1 Main Bearing / Hub 1 Subchassis 1
Bearing Ball 1 Power Cord 1
Some regions will be supplied
by the local importer or dealer
Power Supply 1
3
SET - UP INSTRUCTIONS
The Diva should be installed on a firm level surface for the best results.
Steps 1-8 show pick-up arm installation and subchassis assembly.
Steps 9-12 show pick-up arm alignment.
Steps 13-16 show suspension installation and alignment.
Steps 17-20 show motor and8 drive belt installation.
1 Fit the 3 Suspension Bars to the Subchassis.
Using the 4mm wrench supplied, fit the M5 bolts,
securely fixing the bars.
2 Fit the chosen pick-up arm to the correct arm board.
Feed the arm cable through the large hole in the side.
Pass the arm leads through the "Arm Tube" and insert
tube into arm board, not locking in place.
Push arm lead through hole in subchassis and leave loose.
3 Insert Arm Rods into subchassis, not locking in place.
4 Slide arm board onto rods, pushing arm tube into
subchassis and arm board at same time.
5 Secure arm lead to subchassis using the 2.5mm wrench.
This may need readjusting after stage 6.
6 Align the arm board to the grooves at the end of arm rods,
for correct arm geometry. Lock all arm board and subchassis Pick-up Arm
screws with the wrenches provided.
7 Readjust arm leads as required. Pick-up Arm Leads
8 When fitting 2 arms repeat steps 1-7 opposite.
If only using one arm, fit the balance weight to 2
the subchassis and lock into position.
6
Arm Tube Pick-up Arm
Board
4
Balance Weight Spindle INSET
with cover
8
Arm Rod
3
Subchassis
6 Pick-up Arm Board
Suspension Bars
Arm Rod
Arm Lead
1 Clamp
Alignment
5 Arm Board lock screws
Use 1.5mm wrench
Groove
4
PICK-UP ARM ADJUSTMENTS
9 Clean the spindle of any sticky residue from the spindle cover
making sure the top of spindle is spotless.
Place the Tungsten Bearing Ball into the top of the spindle.
DO NOT USE ANY GLUES OR LUBRICANTS.
THIS BEARING IS DESIGNED TO RUN DRY.
Clamp
10 Fit Hub/Bearing to spindle.
The bearing thrust is a sapphire jewel and extreme care
should always be taken against sudden impacts.
12
11 Carefully fit the Platter to the Hub without
dropping onto the bearing. The location
ring will help with alignment.
12 Place record onto platter and clamp.
Record
It is now recommended to make the set-up
adjustments to the pick-up arm before the
suspension is fitted.
Platter
11
Before moving to the next section,
removing the clamp, record and
platter is recommended.
Hub
10
Tungsten Bearing Ball
9
Bearing Spindle
5
SUSPENSION INSTALLATION AND ADJUSTMENT
13 Remove M5 retaining bolt from the suspension cover with wrench provided.
Insert end of spring into suspension bar as diagram. Fit all 3 units.
14 The Platter should now be leveled by adjusting each spring in turn.
This is done by holding spring and turning foot as in diagram below.
Move the feet so that the springs do not touch the adjusters lower body.
15 The base of the suspension bars should be about 3 - 5mm from the top of foot.
Once the motor and drive belt have been fitted readjustment may be required.
16 The suspension will be correctly set when the drive hub is level with the
drive pulley and the platter, subchassis and pick-up arm move in a smooth
pistonic motion without any wobble.
Once correctly set the suspension covers can be refitted so that
the suspension bars do not touch.
13
14
6
DRIVE SYSTEM AND ALIGNMENT
17 With the platter removed place the motor in close proximity to the drive hub
within the cut-out in the subchassis. Pass the motor lead under the subchassis.
18 The Drive Belt should only be handled with clean hands. If it becomes dirty the
turntable will not perform correctly and will need replacing.
Drive Belts cannot be cleaned so handle with great care.
Fit the Drive Belt by removing the platter. Place belt around hub
and then around drive pulley. Refit platter, record and
clamp and recheck for alignment.
19 Correct alignment of the suspension
will ensure the platter is level and the
hub in line with drive pulley.
20 Finally connect PSU to the motor and
start. Recheck suspension is smooth
and fit suspension covers.
More important than absolute level is
the smooth operation of the suspension,
therefore bubble levels are not required. Drive Belt
18
20
Drive Pulley
17
AV I D
Drive Motor
19
Platter
33 RPM Drive Belt
45 RPM
Drive Hub
Drive
Motor Subchassis
3 - 4mm
7
MOTOR / PSU CONNECTIONS PSU OPERATION
Play indicator
IEC Mains Inlet
PSU (Rear)
Motor
Fuse Start / Stop switch
Holder
Motor Lead
Connector
2 Operation of the turntable is done by the rotary switch
on the front panel.
When turned clockwise to switch on a red light shines
Supplied Mains Cord
to confirm power.
Turn anti-clockwise to switch off.
This also disconnects the mains supply.
1
Speed change is done by moving the drive belt from
one pulley diameter to another.
Mains Supply
CLAMP OPERATION
1 Motor connection to PSU
The locking connector at the end of the motor The clamp supplied is an
lead will only fit one way and should then be integral part of the Diva
locked into position. design and should be
2 Use IEC type mains lead supplied. used when a record
is played.
! DURING OPERATION THE MOTOR WILL BECOME HOT.
THIS IS NORMAL AND DOES NOT EFFECT PERFORMANCE. After placing the record onto the platter screw
the clamp onto the spindle thread clockwise.
FOR BEST PERFORMANCE WE RECOMMENDED THE POWER SUPPLY Take care not to hit or cross-thread the spindle.
IS PLACED AWAY FROM THE TURNTABLE AND SUPPORT SURFACE. Screw anti-clockwise to remove the clamp.
8
POWER SUPPLY FUSE WARRANTY
The mains socket is an IEC type and you should use the supplied 2 YEAR LIMITED WARRANTY - TERMS AND CONDITIONS.
lead or a suitable alternative fused at 3 Amps where fitted.
The socket contains an input fuse and in case of failure this should AVID warrants this product designated herein to be free of
be checked first. Fuse ratings are; manufacturing defects in material and workmanship,
subject to the conditions hereinafter set forth, for a period
100-120v = 250v 2 Amp 220-240v = 250v 1 Amp
of twenty-four (24) months from the date of purchase by the
original purchaser or no later than thirty (30) months
CHANGING FUSE. from the date of shipment to an authorized AVID agent,
Always exchange for the correct value. whichever come first, except for the following items;
1. Sapphire Thrust Bearing
1. Use of flat screwdriver to open 2. Drive Belt
the fuse holder from socket. These items have no warranty, however replacements may
2. Remove fuse and check. be issued by AVID at our discretion.
If faulty replace with new one.
This will click into place. This warranty is subject to the following conditions and
3. Push fuse holder back into the limitations. The warranty is void and inapplicable if the
socket until flush. product has been used or handled other than in accordance
with the instructions in this manual, abused or misused,
! CONTACT YOUR SUPPLIER IF IN DOUBT
damaged by accident or neglect or in being transported, or
if the defect is due to the product being repaired or tampered
with by anyone other than AVID or an agent with prior
authorization. The product must be packed and returned, in
its original packing, to AVID or an authorized agent by the
customer at their expense. (If no packing is available, AVID
will supply this as a chargeable item.) AVID will pay the
return freight of its choice. Any claim arising should be made
in the first instance in writing to AVID or authorized agent
CLEANING direct before returning any product. If product needs to be
returned a written description of the defect and a photocopy
of the original purchase receipt must accompany it. This
receipt must clearly list the model and serial number, date
To maintain the visual appearance of the DIVA, occasionally dust of purchase, the name and address of the purchaser and
the surfaces with a normal duster. Do not use benzene, thinner or authorized dealer and the price paid by the purchaser.
chemical solvent or wipe with a chemically treated cloth. AVID reserves the right to modify the design of any product
without obligation to purchasers of previously manufactured
Fingerprints, greasy marks or similar smudges on the metal work products and to change the prices or specifications of any
can be removed with a dry cloth, mild soapy water or alcohol product without notice or obligation to any person.
cleaner. Never use an abrasive cleaner. Any implied warranties relating to the above product shall be
limited to the duration of this warranty. This warranty does
Do not attempt to clean the drive belt with anything. If dirty or not extend to any incidental or consequential costs or
greasy it will probably need replacing. damages to the purchaser.
WARRANTOR.
The glass top of the platter can be cleaned with glass cleaner. Inquiries regarding the above Limited Warranty may be sent
to the address below.
AVID. Unit 52, 137 North Gate, Alconbury Airfield, Alconbury,
Huntingdon, Cambridgeshire PE28 4WX England
EC Declaration of Conformity
We declare that our DIVA PSU used in our DIVA turntables conform to the following directives
and harmonized international standards.
LVD (73/23/EEC) Low voltage directive. EMC (89/36/EEC) Electromagnetic conformity.
CENELEC HD21/22 Flexible cables and cords. BS EN 60065: 1994 Safety requirements for
mains operated electronic and related apparatus for household and similar general use.
EN 55013: 1990 Electromagnetic Emissions. EN 55020: 1988 Electromagnetic Immunity.
C.Mas
Proprietor
AVID
9