Text preview for : Tonomac_TO-4-2941_Chassis_UOC_TDA8377.pdf part of . Various Tonomac TO-4-2941 Chassis UOC TDA8377 . Various CHINA TV TV Tonomac_TO-4-2941_Chassis_UOC_TDA8377.pdf
Back to : Tonomac_TO-4-2941_Chassis | Home
COLOR TELEVISION
TS2750J
(TK2750)
CONTENTS
Safety instruction.................................................................................1
General instruction..................................................................................1
Alignment instruction..............................................................................2
Alignment f low ............................. ........................... ..........................2
A l i g n m e n t m e t h o d ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . .3
BLOCK DIAGRAM.................................................................................... 8
MAIN IC............................................................................................ 9
Exploded view................................................................................13
Part list .........................................................................................15
Schematic diagram.............................................................................32
Note: This service manual is only for professional service personnel's reference. Before
servicing the unit, please read the following items carefully.
1 safety instruction
1.1 X-RAY radiation precaution
1.1.1 Excessive voltage will cause harmful X-ray. To avoid this radiation hazard, the high voltage should
fall within the limitation. The appliance works at AC 120V, 60Hz. The high voltage of zero beam current
should be within 29.0kV on condition that the main power (B+) voltage is AC135V. And it should not
exceed 30kV in any condition.
* Keep the main power voltage at 135V when checking the high voltage.
1.1.2 The primary source of X-RAY RADIATION is the CRT. The CRT of this TV set have gotten the
approval of safety authentication inspection. The replacement CRT should be exactly the same type and
specification CRT which has gotten a similar safety approval, and check the high voltage according to
the HIGH VOLTAGE CHECK procedure.
1.2 safety precaution
a. Since the power supply circuit of this receiver is directly connected to the AC power line, an isolation
transformer is necessary during dynamic service to avoid possible shock hazard.
b. Always discharge the graphite layer conductor when moving the CRT.
c. Disconnect the power cord before replacing parts.
d. When replacing high-power resistor, keep the resistor 10 mm away from the circuit board.
1.3 Component safety precaution
Many electrical and mechanical parts in the chassis have special safety-related characteristics. These
characteristics are often passed unnoticed by a visual inspection. Replacement parts which have these
special safety characteristics are identified in this manual and its supplement electrical components
having such features are shaded or marked by on the schematic diagram and the parts list. Before
replacing any of these components, read the parts list in this manual carefully. The use of substitute
replacement parts which do not have the same characteristic as specified in the parts list may create
shock, fire, X-RAY RADIATION or other hazards.
2.General instruction
2.1 Copy the standard model data to let EEPROM of the chassis have those data before placing it on the
unit, do "factory adjustment" if necessary. If use a blank EEPROM directly, you should preset IIC data
and then do other common adjustment. Refer to TABLE1 to preset EEPROM.
2.2 the adjustment should be done under following circumstances without additional instruction
a) Alternating current 120V/60Hz
b) Preheat at least 30 min
2.3The unit has auto degaussing circuit, the auto degaussing process can be finished within 1s when the
main power. only when turn on the unit at least 30min after last time turn off TV does the auto
degaussing circuit work.
2.4 If the CRT with magnetism affects color purity and convergence, when the auto degaussing
eraser. if the color purity and convergence are still not very good, then corresponding adjustment
should be done. Refer to picture tube adjustment method for adjustment.
3 Alignment instruction
1
3.1 Debugging item
a)adjust mode instruction
b)B+ voltage adjustment
c)RFAGC voltage adjustment
d)focus adjustment
e)Screen-grid voltage white balance, sub brightness adjustment
f)filed scan center, line , amplitude adjustment
g)H-scan center adjustment
3.2 Alignment flow
Normal
+B adjustment temperature aging Focus adjustment AGC adjustment
White balance Picture adjustment
adjustment
Fig-1 alignment flow
3.3 Enter/exit factory adjustment method
Use remote control, press "MENU" button, then press 6483,"M"will appear on screen to show that you
have entered the factory adjustment method, press "STANDBY" to exit it.
3.4 Select adjustment item and adjust data
After entering factory adjustment mode, press 1-4 number buttons to select menu1- menu4; To enter into
MENU0~MENU5, press "CHILD LOCK" button and then the number button (5~0) to enter into relative
menus. Press "P+" and "P-" to select and "V+" and "V-"to adjust.
4 Alignment method
4.1 B+ voltage adjustment
a) connect B+ point with a digital voltmeter to measure the negative pole of VD524
b) receive PHILIPS test pattern signal and set the picture to standard.
c) Adjust VR501 to let the value of B+ voltage be 135 V