L500B.pdf part of Daewoo L500B L500B.rar, Service Manual TFT LCD MONITOR Model : L500B text manual preview

Text preview for : L500B.pdf part of Daewoo L500B Service Manual TFT LCD MONITOR Model : L500B

Back to : L500B.rar | Home

Service Manual
TFT LCD MONITOR Model : L500B

DAEWOO ELECTRONICS CO., LTD OVERSEAS SERVICE DEPT.

TABLE OF CONTENTS
SAFETY PRECAUTIONS ................................................................................................. 2 GENERAL SAFETY INFORMATION.................................................................................. 3 SERVICING PRECAUTIONS ........................................................................................... 4 GENERAL INFORMATION ............................................................................................. 8 PIN CONNECTOR ....................................................................................................... 9 OPERATION & ADJUSTMENT ........................................................................................ 10 ALIGNMENT PROCEDURE ............................................................................................ 14 TROUBLE SHOOTING HINTS .......................................................................................... 15 BLOCK DIAGRAM ....................................................................................................... 22 PCB LAYOUT ............................................................................................................... 23 SCHEMATIC DIAGRAM ................................................................................................ 25 EXPLODED VIEW & MECHANICAL PARTS LIST ................................................................ 33 INFORMATION OF PART DESCRIPTION ......................................................................... 34 ELECTRICAL PARTS LIST ................................................................................................ 35

1

SAFETY PRECAUTIONS
CAUTION No modifications of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar with all of the following safety check and servicing guidelines.

u Fire & Shock Hazard
w In servicing, pay attention to original lead dress especially in the high voltage circuit. if a short circuit is found, replace all parts which have been overheated as a result of the short circuit. w All the protective devices must be reinstalled per original design. w Soldering must be inspected for possible cold solder points, frayed leads, damaged insulation, solder splashes or sharp solder points. Be certain to remove all foreign materials.

u Implosion Protection
TFT LCD in this monitor employs integral implosion protection system, but care should be taken to avoid damage and scratching during installation. Use only same type replacement TFT panel. IMPORTANT SAFETY NOTICE There are special components used in analog TFT LCD color display, which are important for safety. These parts are shaded on the schematic diagram and on the replacement parts list. It is essential that these critical parts should be replaced with manufacturer' specified parts to prevent X-radiation, s shock, fire or other hazards. Do not modify the original design without getting a written permission from DAEWOO ELECTRONICS CO. or this will void the original parts and labor warranty.

2

GENERAL SAFETY INFORMATION
u Terms in the manual
CAUTION WARNING Statements identify conditions or practices that could result in damage to the equipment or other property. Statements identify conditions or practices that could result in personal injury or loss of life.

u Terms as marked on equipment
CAUTION WARNING Statements indicate a personal injury hazard not immediately accessible as one reads the marking, or a hazard to properly including the equipment itself. Statements indicate a personal injury hazard immediately accessible as one reads the marking

u Symbols in the manual
This symbol indicates where applicable cautionary or other information is to be found.

u Symbols as marked on equipment
Protective GROUND terminal

u High Voltage Warning And Critical Component Warning Label
Following warning label is on the backlight outside. WARNING This product includes critical mechanical and electrical parts. For continued safety, replace critical components indicated in the service manual only with exact replacement parts given in the parts list. Refer to service manual for measurement procedures and proper service adjustments.

3

SERVICING PRECAUTIONS
CAUTION Before servicing instruments covered by this service manual, its supplements and addendum, read and follow the SAFETY PRECAUTIONS of this manual. NOTE If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 1 of this manual, always follow the safety precautions. Remember: Safety First.

u General Servicing Precautions
1. Always unplug the AC power cord from the AC power source before: a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly. b. Disconnecting or reconnecting any electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument. CAUTION A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in a explosion hazard. 2. Do not any spray chemicals on or near this instrument or any or its assemblies. 3. Unless specified otherwise in this service manual, clean electrical contacts by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive applicator: 10% (by volume) Aceton and 90% (by volume) isopropyl alchohol (90%-99% strength). CAUTION This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts is not required. 4. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 5. Always connect the test instrument ground lead to the appropriate instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last. 6. Use only the test fixtures specified in this service manual with this instrument. CAUTION Do not connect the test fixture ground strap to any heatsink in this instrument.

4

SERVICING PRECAUTIONS

u Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. The examples of typical ES devices are integrated circuits, some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate enough electrical charges to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate enough electrical charges to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION Be sure that no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmful motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate enough static electricity to damage an ES devices).

u General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron with appropriate tip size and shape that will maintain tip temperature within a 550�F-660�F (288�C-316�C) range. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean. 4. Throughly clean the surface to be soldered. Use a small wire-bristle (0.5 inch or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following soldering technique: a. Allow the soldering iron tip to reach normal temperature (550�F to 660�F or 288�C to 316�C) b. Hold the soldering iron tip and solder strand against the component lead until the solder melts. c. quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush. CAUTION Work quickly to avoid overheating the circuit board printed foil.
5

SERVICING PRECAUTIONS

FIGURE1. USE SOLDERING IRON TO PRY LEADS

u IC Removal / Replacement
Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted and then bent flat against the circuit foil. When holes are slotted, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 on the page under the title of general soldering guidelines.

u Removal
1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with desoldering braid before removing the IC.

u Replacement
1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (lt is not necessary to reapply acrylic coating to the area).

u "Small-Signal" Discrete Transistor Removal/Replacement
1. 2. 3. 4. Remove the defective transistor by clipping its leads as close as possible to the component body. Bend the end of each of three leads remaining on the circuit board into a "U" shape. Bend the replacement transistor leads into a "U" shape. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insoure metal-to-metal contact, then solder each connection.

6

SERVICING PRECAUTIONS

u Power IC, Transistor or Devices Removal / Replacement
1. 2. 3. 4. 5. 6. Heat and remove all solders from the device leads. Remove the heatsink mounting screw (if applicable). Carefully remove the device from the circuit board. Insert new device in circuit board. Solder each device lead, and clip off excess lead. Replace heatsink.

u Diode Removal / Replacement
1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicularly to the circuit board. 3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect the solder joints of the two "original" leads on the circuit board copper side. If they are not shiny, reheat them and apply additional solder if necessary.

uTECHNICAL INFORMATION
Electrical Pixel pitch Horizontal frequency Vertical frequency Operating temperature Operating humidity Mechanical Cabinet Dimension (set with packing) Weight(net) Controls Molded Plastic Cabinet with attachable tilt & swivel base 502(H) X 502(W) X 242(D) mm 4.5 Kg Power Switch OSD control 0.3mm X 0.3mm 30KHz to 62KHz (Automatically) 50Hz to 85Hz (Automatically) 10-40�C / 50-104�F 8-80%

7

GENERAL INFORMATION
This TFT LCD monitor automatically scans all horizontal frequencies from 30KHz to 62KHz, and all vertical frequencies from 50Hz to 85Hz. This TFT LCD monitor supports IBM PC, PC/XT, PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid color graphics display when using the following graphics adapters : (VGA, Super VGA, VESA and XGA and Apple Macintosh Video Card). And so, this TFT LCD monitor has a maximum horizontal resolution of 1024 dots and a maximum vertical resolution of 768 lines for superior clarity of display. By accepting analog signal inputs which level is zero to 0.7 Volts. This TFT LCD monitor can display and 262, 144 colors depending on the graphics adapter and software being used.(available used to 8 bit panel is 16.7M colors)

u Abbreviations ADJ AFC H.sync OSC P.S.U PWA R.G.B V.sync Adjustment Automatic Frequency Control Horizontal Synchronization Oscillator Power Supply Unit Printed Circuit Board Wiring Assembly Red, Green, Blue Vertical Synchronization

8

PIN CONNECTOR
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Red Green Blue GND GND GND - Red GND - Green GND - Blue +5Vdc GND - H.Sync GND - V.Sync Bi-directional Data (SDA) Horizontal Sync Vertical Sync (VCLK) Data clock (SCL) 6 15 10 1 Signal

Arrangement of 15-pin D-sub connector

uCAUTION FOR ADJUSTMENT AND REPAIR
w The white balance adjustment has been done by a color analyzer in factroy. The adjustment procedure, described in the service manual is made by a visual check. w Allow 20 minutes warm-up time for the display before checking or adjusting only electrical specification or function. w Reform the leadwire after any repair work.

9

OPERATION & ADJUSTMENT
u Control Panel

w Move cursor to the right window on the OSD window. w Increase the value of any selected function. w Move cursor to the left window on the OSD window. w Decrease the value of any selected function. w Launch OSD(On-Screen Display) MENU window. w Move cursor to the high window on the OSD window. w Increase the value of V.center. w Move cursor to the low window on the OSD window. w Decrease the value of V.center.

10

OPERATION & ADJUSTMENT

u Key Process

R G B

Start

w When you choose the icon

on the OSD window, you can exit the OSD screen.

u Hot Key

11

OPERATION & ADJUSTMENT

u Adjustment procedure

Is the mode 1024x768?

Yes

Adjust the FIT SCREEN.

Is the H.Size proper?

No Adjust the CLOCK control.

Is the noise displayed on the screen?

No

Perform the AUTO POSITION.

Perform the AUTO TRACKING.

Is the noise displayed on the screen?

No

Adjust the CLOCK FINE until the screen is cleared.

Yes

Is the noise displayed on the screen yet?

No

End

12

OPERATION & ADJUSTMENT

u OSD Functions
ICON CONTROL LANGUAGE CLOCK FUNCTIONS Select language for OSD (5 languages). Adjust the width (horizontal size) of the screen image. Sharpen the focus by aligning the illuminated pixels and adjust until the screen image looks focused, crisp and sharp. Adjusting the CLOCK FINE after the CLOCK adjustment will produce a clear screen. Choose different preset color temperatures or set your own customized color parameters. Adjust the red color.

CLOCK FINE

COLOR TEMP

RED CONTROL GREEN CONTROL BLUE CONTROL H.CENTER & V.CENTER

Adjust the green color.

Adjust the blue color. Adjust the position of the display horizontally (left or right) and vertically (up or down). Make characters of displayed text easier to read (only for resolutions lower than 1024x768).

FIT SCREEN

SMART SCALING AUTO TRACKING OSD TIME OUT STATUS

Adjust the display image quality (if the screen proceed to scaling up).

Adjust the horizontal & vertical picture image quality and size.

Adjust the display OSD Menu.

Display horizontal & vertical frequency and polarity. Reset the screen to the Factory Preset Display Settings. Choose automatically the proper horizontal position and vertical position & size of the screen image.

RECALL

AUTO POSITION

13

ALIGNMENT PROCEDURE
u Standard Check point
1. Power source : 100-240Vac 50/60Hz 2. Aging: Take at least 20 minutes warm up time. 3. Signal Video input :Analog 0.7Vpp 75 terminal positive polarity Synchronizing : acceptable negative or positive at TTL level Resolution Horizontal : 1024 max. Vertical : 768 max. Frequency Horizontal :30KHz - 62KHz Vertical : 50Hz - 85Hz (available only non interlace mode)

u Adjustment
Smart scaling set to 50%. Contrast set to 100%. Brightness set to 50%. Switching to factory alignment mode Press power key with down menu key( t ) at the power off status. 5. Video level adjustment Receive stair pattern of 16 step (doesn' care any mode). t Readjust coarse R, G, B in TDA8752 menu before saturation point. 6. Set up the tracking See the user' manual at page 8 th. s 7. Switching to user' mode s If turn-off and turn-on then switched to user' mode. s * All of adjusted data stores by fade out of OSD. 1. 2. 3. 4.

14

TROUBLE SHOOTING HINTS
1. Abnormal mode detect

Abnormal mode detect YES

Check input H. Sync of TDA8752.

NO

Trouble video input circuit.

YES

Check waveforms of #84 pin of TDA8752 correct?

NO

Trouble in the TDA8752.

YES

Trouble in the MX88281.

15

TROUBLESHOOTING HINTS

2. Trouble in Power on

Trouble in power on.

Power LED.

ON

Refer to No video or No raster.

OFF

Check output voltage of adapter. YES

NO

Trouble in adapter.

Is the 5VS line normal? YES

NO

Trouble in SQ8 and its ambient circuit.

Is the pulse of pin9 of the IC1? YES Trouble in IC2 or its ambient circuit.

NO

Trouble in Q7 or its ambient circuit.

16

TROUBLESHOOTING HINTS

3. No raster

No raster.

Check the output of the Q10 or #3 pin of CN1.

< 2.5V

Trouble in the Q10 or MX88281 (If it's trouble in the MX88282, change the main B'D)

> 2.5V

CN1 #1 pin 12V check. YES

NO

Check the 12V of the main power.

Check the DC/AC output. YES

NO

Trouble in DC/AC inverter.

Replace LCD panel.

17

TROUBLESHOOTING HINTS

4. One color is missing

One color is missing. YES

Is OSD color normal? YES

NO

Check the output signal of the MX88281 and 74act573.

Is input signal normal? YES

NO

Check video signal cable or video card.

Are the R, G, B digital (8 bit) output of the U17 (TDA8752)?

NO

Replace the main B'D.

YES Trouble in the soldering.

18

TROUBLESHOOTING HINTS

5. Pre check

Pre check

Check output voltage (5V/3.3V/12V).

NO

Check on/off signal of micom.

NO

Check reset signal (#9 pin of micom) and its ambient circuit.

YES

YES

Check output of Q9.

NO

Trouble in the Q9 and its ambient circuit.

YES Trouble each trouble item.

Trouble in the SU1.

19

TROUBLESHOOTING HINTS

6. Abnormal video

Abnormal video

Is the OSD normal?

NO

Is LCLK output the L1 waveform normal?

NO

Check the output of MX88281.

YES YES

Check the control and data signal of SDRAM.

Check connection of 41 pin cable.

20

TROUBLESHOOTING HINTS

7. No video

No video

White

NO

Black

YES

YES

OUT1 41 pin cable connection check. YES

NO

Trouble connection.

Is OSD normal?

NO

No raster

YES

U8 #2 pin output 12V check?

NO

Trouble connection.

Are the contrast controls maximum? YES

NO

Change the contrast control value to maximum

YES

LVCC 3.3V check

Are the video signal and output signal of the TDA8752?

NO

Change the main B'D (Trouble in the TDA8752)

YES OK YES

Are the output signal of the MX88281?

NO

Change the main B'D (Trouble in the TDA8752)

YES Check the LCD panel or 41 pin cable

21

From PC

H/V sync KM416S1020CT X 3

15PIN DSUB CONNECTOR 16M SDRAM X 3

RGB signal

3 16 10 MX88281 H,V sync & dot clock Data line Control line

TDA8752 10 Address line

2

BLOCK DIAGRAM

PRE-AMP

Offset & amplifier

74ACT14 8 8 Scaling 8 Blue Green FRC control & dithering OSD mixer Red 6 6 6

Controller Red Green Blue Buffer 74ACT573 X4

Buffer

3

Current & resistance

22
Dot clock Controller Address & data line I2C bus Micom ( 78 E58 ) On-off control DC-DC converter & on-off control +5V, +3.3V & +12V out 8
DWOSD05

ADC

Clock timing & phase

Sampling clock

OSD signal

Panel driver

H. sync

PLL

OSD circuit Dimming control

H,V sync & pixel clock

Back light

V. sync

630VAC 62KHz

Panel

AC in

12V adapter

+12V

DC-AC inverter

SCHEMATIC DIAGRAM
u MAIN88281A

25

SCHEMATIC DIAGRAM

u TOP CIRCUIT

26

SCHEMATIC DIAGRAM

u BUFFER

27

SCHEMATIC DIAGRAM

u POWER DC/DC

28

SCHEMATIC DIAGRAM

u MEMORY

29

SCHEMATIC DIAGRAM

u MICOM

30

SCHEMATIC DIAGRAM

u RGB/SYNC

31

SCHEMATIC DIAGRAM

u TDA8752A

32

EXPLODED VIEW & MECHANICAL PARTS LIST

33

INFORMATION OF PART DESCRIPTION
Important Safety Notice
Components identified with the International Symbol have special characteristics important for safety. When replacing any components, use only manufacturer' specified parts. s

Abbreviation of Description
RESISTOR Description
Allowance F J K M G

�1% �5% �10% �20% �2%

Example
Fig & Index R18 Part No Description Resistors HRFT472JCA Chip=1/10W 472J

CAPACITOR Description
Allowance C D F J K P Z

�0.25pF �0.5% �1pF �5% �10% �100% ~ 0% �80% ~ -

Example
Fig & Index C044 Part No Description Capacitors HRFT104ZCA Chip CERA 50V Y5V 0.1� F Z 2012

34

ELECTRICAL PARTS LIST
The components identified by mark I have special characteristics important for safety and X-ray. These should be replaced only with the types specified in the parts list.

LOC

PART-CODE 9979720013

PART-NAME ADAPTER POWER CORD POWER ISA50-1

PART-DESC

LOC

PART-CODE

PART-NAME

PART-DESC 50V Y5V 0.01MF Z 2012 50V Y5V 0.01MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.022MF Z 2012 50V Y5V 0.022MF Z 2012 16V 10MF M 3528 TS 50V Y5V 0.1MF Z 2012 50V CH 22PF J 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.01MF Z 2012 50V Y5V 0.01MF Z 2012 50V CH 22PF J 2012 50V Y5V 0.01MF Z 2012 16V 10MF M 3528 TS 50V Y5V 0.022MF Z 2012 50V Y5V 0.1MF Z 2012 16V 10MF M 3528 TS 50V Y5V 0.022MF Z 2012 50V Y5V 0.022MF Z 2012 50V Y5V 0.022MF Z 2012 50V CH 1000PF J 2012 50V Y5V 0.1MF Z 2012 50V CH 1000PF J 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 1000PF J 2012 16V 10MF M 3528 TS 50V Y5V 0.1MF Z 2012 16V 100MF M 7343 TS 50V CH 1000PF J 2012 50V CH 1000PF J 2012 50V CH 1000PF J 2012 16V 10MF M 3528 TS 50V CH 1000PF J 2012 Y5V 50V 0.47MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 1000PF J 2012 50V Y5V 0.1MF Z 2012

I

AD1

C082 HCFK103ZCA C CHIP CERA C083 HCFK103ZCA C CHIP CERA C084 HCFK104ZCA C CHIP CERA C085 HCFK104ZCA C CHIP CERA C086 HCFK104ZCA C CHIP CERA C087 HCFK223ZCA C CHIP CERA C088 HCFK223ZCA C CHIP CERA C090 HCTBF100MB C CHIP TANTAL C091 HCFK104ZCA C CHIP CERA C092 HCQK220JCA C CHIP CERA C093 HCFK104ZCA C CHIP CERA C094 HCFK103ZCA C CHIP CERA C095 HCFK103ZCA C CHIP CERA C096 HCQK220JCA C CHIP CERA C097 HCFK103ZCA C CHIP CERA C098 HCTBF100MB C CHIP TANTAL C099 HCFK223ZCA C CHIP CERA C1 C10 HCFK104ZCA C CHIP CERA HCTBF100MB C CHIP TANTAL

AD1A W3414M731-

KKP-419C/KKS-15A 1.8M(BK) 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.01MF Z 2012 50V Y5V 0.01MF Z 2012 50V Y5V 0.01MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 22PF J 2012 16V 1MF M 3216 16V 100MF M 7343 TS 50V Y5V 0.1MF Z 2012 16V 100MF M 7343 TS 16V 1MF M 3216 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 1000PF J 2012 35V 22MF M 7343 50V Y5V 0.1MF Z 2012 Y5V 50V 0.15MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012

C044 HCFK104ZCA C CHIP CERA C045 HCFK104ZCA C CHIP CERA C046 HCFK103ZCA C CHIP CERA C047 HCFK103ZCA C CHIP CERA C048 HCFK103ZCA C CHIP CERA C049 HCFK104ZCA C CHIP CERA C050 HCFK104ZCA C CHIP CERA C051 HCFK104ZCA C CHIP CERA C052 HCFK104ZCA C CHIP CERA C053 HCFK104ZCA C CHIP CERA C054 HCFK104ZCA C CHIP CERA C055 HCFK104ZCA C CHIP CERA C056 HCFK104ZCA C CHIP CERA C057 HCFK104ZCA C CHIP CERA C058 HCFK104ZCA C CHIP CERA C059 HCFK104ZCA C CHIP CERA C060 HCFK104ZCA C CHIP CERA C061 HCFK104ZCA C CHIP CERA C062 HCFK104ZCA C CHIP CERA C063 HCFK104ZCA C CHIP CERA C064 HCFK104ZCA C CHIP CERA C065 HCFK104ZCA C CHIP CERA C066 HCFK104ZCA C CHIP CERA C067 HCQK220JCA C CHIP CERA C068 HCTAF109MB C CHIP TANTAL C069 HCTEF101MC C CHIP TANTAL C070 HCFK104ZCA C CHIP CERA C071 HCTEF101MC C CHIP TANTAL C072 HCTAF109MB C CHIP TANTAL C073 HCFK104ZCA C CHIP CERA C074 HCFK104ZCA C CHIP CERA C075 HCQK102JCA C CHIP CERA C076 HCTEJ220MC C CHIP TANTAL C077 HCFK104ZCA C CHIP CERA C078 HCFK154ZCA C CHIP CERA C079 HCFK104ZCA C CHIP CERA C080 HCFK104ZCA C CHIP CERA C081 HCFK104ZCA C CHIP CERA

C100 HCFK223ZCA C CHIP CERA C101 HCFK223ZCA C CHIP CERA C102 HCFK223ZCA C CHIP CERA C103 HCQK102JCA C CHIP CERA C104 HCFK104ZCA C CHIP CERA C105 HCQK102JCA C CHIP CERA C107 HCFK104ZCA C CHIP CERA C108 HCFK104ZCA C CHIP CERA C109 HCQK102JCA C CHIP CERA C11 HCTBF100MB C CHIP TANTAL

C110 HCFK104ZCA C CHIP CERA C111 HCTEF101MC C CHIP TANTAL C112 HCQK102JCA C CHIP CERA C113 HCQK102JCA C CHIP CERA C114 HCQK102JCA C CHIP CERA C115 HCTBF100MB C CHIP TANTAL C116 HCQK102JCA C CHIP CERA C117 HCFK474ZCA C CHIP CERA C118 HCFK104ZCA C CHIP CERA C119 HCQK102JCA C CHIP CERA C12 HCFK104ZCA C CHIP CERA

35

ELECTRICAL PARTS LIST

LOC

PART-CODE

PART-NAME

PART-DESC Y5V 50V 0.47MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 16V 10MF M 3528 TS 16V Y5V 1MF Z 3216 50V CH 120PF J 2012 50V CH 120PF J 2012 16V 1MF M 3216 16V 10MF M 3528 TS 16V 10MF M 3528 TS 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 16V 10MF M 3528 TS 16V 10MF M 3528 TS 16V 10MF M 3528 TS 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 22PF J 2012 50V CH 22PF J 2012 16V 10MF M 3528 TS 50V Y5V 0.1MF Z 2012 50V CH 47PF J 2012 50V CH 33PF J 2012 16V 10MF M 3528 TS 16V 10MF M 3528 TS 16V 100MF M 7343 TS 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 22PF J 2012 16V 10MF M 3528 TS 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 16V 1MF M 3216 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012

LOC

PART-CODE

PART-NAME

PART-DESC 50V CH 1000PF J 2012 16V 10MF M 3528 TS 16V 10MF M 3528 TS 50V CH 22PF J 2012 50V CH 47PF J 2012 50V CH 47PF J 2012 16V 10MF M 3528 TS 50V CH 15PF J 2012 16V 10MF M 3528 TS 16V 10MF M 3528 TS 50V Y5V 0.1MF Z 2012 Y5V 50V 0.47MF Z 2012 Y5V 50V 0.47MF Z 2012 50V Y5V 0.1MF Z 2012 16V 10MF M 3528 TS 16V 10MF M 3528 TS 16V 10MF M 3528 TS 16V 10MF M 3528 TS 50V Y5V 0.1MF Z 2012 50V CH 10PF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V CH 1000PF J 2012 50V Y5V 0.1MF Z 2012 15P+15P/DDC=1.5M(GY275A) SMAW250-05 (ANGLE) SMH250+5264-5+1007#24=110 SMAW250-09 (ANGLE) SMH250-9*2+1007#24=270 SMAW250-03 (ANGLE) SMH250-3*2+1354#28=250 SMAW250-06 (ANGLE) SMH250-6*2+2464#24=120 SMAW250-07 (ANGLE) SMH250+1354#28+OP14A=100 SMAW250-07 (ANGLE) SMAW250-06 (ANGLE) SMAW250-03 (ANGLE) SMAW250-09 (ANGLE) RLS4148 RLS4148 RLS4148 RLS4148 RLZTE-11 5.6B

C120 HCFK474ZCA C CHIP CERA C121 HCFK104ZCA C CHIP CERA C122 HCFK104ZCA C CHIP CERA C123 HCTBF100MB C CHIP TANTAL C124 HCFF105ZEA C CHIP CERA C125 HCQK121JCA C CHIP CERA C126 HCQK121JCA C CHIP CERA C127 HCTAF109MB C CHIP TANTAL C128 HCTBF100MB C CHIP TANTAL C129 HCTBF100MB C CHIP TANTAL C13 HCFK104ZCA C CHIP CERA

C273 HCQK102JCA C CHIP CERA C28 C29 C3 C31 C32 C33 C34 C35 C36 C37 C38 C39 C4 C40 C41 C42 C43 C5 C6 C7 C8 HCTBF100MB C CHIP TANTAL HCTBF100MB C CHIP TANTAL HCQK220JCA C CHIP CERA HCQK470JCA C CHIP CERA HCQK470JCA C CHIP CERA HCTBF100MB C CHIP TANTAL HCQK150JCA C CHIP CERA HCTBF100MB C CHIP TANTAL HCTBF100MB C CHIP TANTAL HCFK104ZCA C CHIP CERA HCFK474ZCA C CHIP CERA HCFK474ZCA C CHIP CERA HCFK104ZCA C CHIP CERA HCTBF100MB C CHIP TANTAL HCTBF100MB C CHIP TANTAL HCTBF100MB C CHIP TANTAL HCTBF100MB C CHIP TANTAL HCFK104ZCA C CHIP CERA HCQK100JCA C CHIP CERA HCFK104ZCA C CHIP CERA HCFK104ZCA C CHIP CERA

C130 HCFK104ZCA C CHIP CERA C131 HCFK104ZCA C CHIP CERA C132 HCFK104ZCA C CHIP CERA C133 HCFK104ZCA C CHIP CERA C136 HCTBF100MB C CHIP TANTAL C139 HCTBF100MB C CHIP TANTAL C14 HCTBF100MB C CHIP TANTAL

C141 HCFK104ZCA C CHIP CERA C142 HCFK104ZCA C CHIP CERA C143 HCFK104ZCA C CHIP CERA C144 HCFK104ZCA C CHIP CERA C145 HCFK104ZCA C CHIP CERA C146 HCFK104ZCA C CHIP CERA C147 HCFK104ZCA C CHIP CERA C148 HCQK220JCA C CHIP CERA C149 HCQK220JCA C CHIP CERA C15 HCTBF100MB C CHIP TANTAL

C813 HCQK102JCA C CHIP CERA C9 HCFK104ZCA C CHIP CERA CABLE SIGNAL AS CONN WAFER CONN AS CONN WAFER CONN AS CONN WAFER CONN AS CONN WAFER CONN AS CONN WAFER CONN AS CONN WAFER CONN WAFER CONN WAFER CONN WAFER DIODE CHIP DIODE CHIP DIODE CHIP DIODE CHIP DIODE ZENER CHIP

CA01 9970800035 CN1 9979220020 CN1A 9970750034 CN2 9979220024 CN2A 9970790107 CN3 9979220018 CN3A 9970730071 CN4 9979220021 CN4A 9970760042 CN5 9979220022 CN5A 9970760043 CW1 9979220022 CW2 9979220021 CW3 9979220018 CW4 9979220024 D1 D2 D3 D4 D5 DRLS4148-DRLS4148-DRLS4148-DRLS4148-DRLZ5R6B-B

C150 HCFK104ZCA C CHIP CERA C151 HCQK470JCA C CHIP CERA C152 HCQK330JCA C CHIP CERA C16 C17 HCTBF100MB C CHIP TANTAL HCTBF100MB C CHIP TANTAL

C179 HCTEF101MC C CHIP TANTAL C18 C19 C2 C20 C21 C22 C23 C24 C25 C27 HCFK104ZCA C CHIP CERA HCFK104ZCA C CHIP CERA HCQK220JCA C CHIP CERA HCTBF100MB C CHIP TANTAL HCFK104ZCA C CHIP CERA HCFK104ZCA C CHIP CERA HCTAF109MB C CHIP TANTAL HCFK104ZCA C CHIP CERA HCFK104ZCA C CHIP CERA HCFK104ZCA C CHIP CERA

36

ELECTRICAL PARTS LIST

LOC

PART-CODE

PART-NAME D-SUB 15P ANGLE

PART-DESC 15P DDC BLUE W/IN SCREW CFI-06-B-1H-471M W78E58-24 WSDIF-40T 74HCT4538D BAI1501 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING 1/0.52 TIN COATING POWER JACK 6.5PIE 14.5*9 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 TB321611Z260 LM151X2-C2TH SD50GYW(GREEN/AMBER) DBBV-41PJ-1.0SM DF-9-41S*2+1571#32=220 KTC3875SY(RTK) KDS226(RTK) KDS226(RTK) KDS226(RTK) KDS226(RTK) KDS226(RTK) KDS226(RTK)

LOC Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9

PART-CODE TKTC3875SY TKTC3875SY 1K1A7805P1 TKTC3875SY TKTC3875SY 1KA7542---

PART-NAME TR CHIP TR CHIP IC REGULATOR TR CHIP TR CHIP IC VOTAGE DETECTOR

PART-DESC KTC3875SY(RTK) KTC3875SY(RTK) KIA7805API KTC3875SY(RTK) KTC3875SY(RTK) KA7542 KDS226(RTK) KTC3875SY(RTK) 1/6 4.7K OHM J 1/6 4.7K OHM J 1/6 4.7K OHM J 1/10 4.7K OHM J 2012 1/10 1K OHM J 2012 1/10 100 OHM J 2012 1/10 100K OHM J 2012 1/10 470K OHM J 2012 1/10 10K OHM J 2012 1/2 100 OHM J 1/10 1M OHM J 2012 1/10 1M OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 22 OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 47K OHM J 2012 1/10 4.7K OHM J 2012 1/10 0 OHM J 2012 1/10 22 OHM J 2012 1/10 22 OHM J 2012 1/10 1K OHM J 2012 1/10 4.7K OHM J 2012 1/10 4.7K OHM J 2012 1/10 3.6K OHM J 2012 1/10 3.6K OHM J 2012 1/10 4.7K OHM J 2012 1/10 22 OHM J 2012 1/10 51K OHM J 2012 1/10 5.1K OHM J 2012 1/10 5.1K OHM J 2012 1/10 10K OHM J 2012 1/10 4.7K OHM J 2012 1/10 100 OHM J 2012 1/10 4.7K OHM J 2012

DSUB1 9979200209 EF1 IC1

5PF1BH471M FILTER LC 1DWM300--IC MICOM SOCKET IC IC LCD INVERTER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER WIRE COPPER JACK DC COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD COIL CHIP BEAD

IC1A 9979300500 IC2 174HCT4538

I

INV1 DBA11501-J001 85801052GY J002 85801052GY J003 85801052GY J004 85801052GY J005 85801052GY J006 85801052GY J007 85801052GY J008 85801052GY J009 85801052GY J010 85801052GY J011 85801052GY JACK1 9979100010 L1 L10 L11 L12 L13 L15 L16 L2 L28 L4 L5 L6 L7 L8 L9 LCD HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B HFFTB2601B

DKDS226RTK DIODE CHIP TKTC3875SY TR CHIP R CARBON FILM R CARBON FILM R CARBON FILM R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CARBON FILM R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP

R001 RD-AZ472JR002 RD-AZ472JR003 RD-AZ472JR1 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R2 R20 R22 R23 R3 R32 R34 R35 R36 R4 R40 HRFT472JCA HRFT102JCA HRFT101JCA HRFT104JCA HRFT474JCA HRFT103JCA RD-2Z101JHRFT105JCA HRFT105JCA HRFT472JCA HRFT472JCA HRFT220JCA HRFT472JCA HRFT472JCA HRFT473JCA HRFT472JCA HRFT000JCA HRFT220JCA HRFT220JCA HRFT102JCA HRFT472JCA HRFT472JCA

DLM151X2C2 LCD

R400 HRFT362JCA R401 HRFT362JCA R41 R5 R51 R52 R53 R55 R6 R7 R8 HRFT472JCA HRFT220JCA HRFT513JCA HRFT512JCA HRFT512JCA HRFT103JCA HRFT472JCA HRFT101JCA HRFT472JCA

LED1 DSD50GYW-- LED OUT1 9979220080 OUTA 9970741001 Q10 Q12 Q13 Q14 Q15 Q16 Q17 TKTC3875SY CONN WAFER CONN AS TR CHIP

DKDS226RTK DIODE CHIP DKDS226RTK DIODE CHIP DKDS226RTK DIODE CHIP DKDS226RTK DIODE CHIP DKDS226RTK DIODE CHIP DKDS226RTK DIODE CHIP

37

ELECTRICAL PARTS LIST

LOC

PART-CODE

PART-NAME R CHIP R CHIP R CHIP R CHIP R CHIP

PART-DESC 1/10 75 OHM J 2012 1/10 75 OHM J 2012 1/10 75 OHM J 2012 1/10 1K OHM J 2012 1/10 3K OHM J 2012 HB-4H3216-300JT HB-4M3216-121JT HB-4M3216-121JT HB-4M3216-121JT HB-4H3216-300JT HB-4H3216-300JT HB-4H3216-300JT HB-4H3216-300JT HB-4M3216-121JT HB-4M3216-121JT HB-4M3216-121JT 1W 33 OHM J (TAPPING) KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P KPT-1115VM 1C-1P 35V 22MF M 7343 10V 220MF M 7343 10V 220MF M 7343 10V 220MF M 7343 10V 220MF M 7343 35V 22MF M 7343 35V 22MF M 7343 16V 10MF M 3528 TS 16V Y5V 1MF Z 3216 16V 4.7MF M 3528 50V Y5V 0.1MF Z 2012 50V Y5V 0.1MF Z 2012 50V Y5V 0.01MF Z 2012 50V Y5V 0.01MF Z 2012 16V Y5V 1MF Z 3216 KDS181(RTK)

LOC SD2 SD3 SL1 SL2

PART-CODE DSK14----DSK14-----

PART-NAME DIODE SCHOTTKY DIODE SCHOTTKY SK14 SK14

PART-DESC

R801 HRFT750JCA R811 HRFT750JCA R821 HRFT750JCA R9 R92 RP1 HRFT102JCA HRFT302JCA

HLC220M00E L CHIP COIL HLC220M00E L CHIP COIL FET CHIP FET CHIP IC REGULATOR CHIP FET CHIP TR CHIP IC REGULATOR CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP

22UH M (BA220) 22UH M (BA220) FDS6930A FDS6930A KIA78L05F(RTF) NDS9435A 2N3904S(RTK) KIA78L05F(RTF) 1/10 100K OHM J 2012 1/10 22 OHM J 2012 1/10 100K OHM J 2012 1/10 100K OHM J 2012 1/10 11K OHM J 2012 1/10 10K OHM J 2012 1/10 10K OHM J 2012 1/10 100K OHM J 2012 1W 0.04 OHM J 8340 1W 0.02 OHM J 8340 SB3052P(SSOP-28) M62393P TDA8752AH/8 TC74ACT14FN MX88281FC TC74ACT573FT(EL) TC74ACT573FT(EL) TC74ACT573FT(EL) AT24C21 ZRC250N802 KM416S1020CT-G8 KM416S1020CT-G8 KM416S1020CT-G8 AT24C16-10PC DWOSD05 NDS9958 TC74ACT573FT(EL) HC-49/S 14.31818MHZ 50PPM HC-49/S 11.0592MHZ 30PPM

SQ1 TFDS6930ASQ2 TFDS6930ASQ3 1K1A78L05F SQ6 TNDS9435ASQ7 T2N3904SRT SQ8 1K1A78L05F SR1 HRFT104JCA

HFFH4H300E COIL CHIP BEAD

RP10 HFFH4M121E COIL CHIP BEAD RP12 HFFH4M121E COIL CHIP BEAD RP13 HFFH4M121E COIL CHIP BEAD RP2 RP3 RP4 RP5 RP7 RP8 RP9 HFFH4H300E COIL CHIP BEAD HFFH4H300E COIL CHIP BEAD HFFH4H300E COIL CHIP BEAD HFFH4H300E COIL CHIP BEAD HFFH4M121E COIL CHIP BEAD HFFH4M121E COIL CHIP BEAD HFFH4M121E COIL CHIP BEAD R M-OXIDE FILM SW TACT SW TACT SW TACT SW TACT SW TACT SW TACT

SR10 HRFT220JCA SR14 HRFT104JCA SR15 HRFT104JCA SR16 HRFT113JCA SR2 SR3 SR4 SR5 SR6 SU1 HRFT103JCA HRFT103JCA HRFT104JCA

RW2 RS01Z330JS001 5S50101Z01 S002 5S50101Z01 S003 5S50101Z01 S004 5S50101Z01 S005 5S50101Z01 S006 5S50101Z01 SC1

HRM1407JPD R CHIP METAL PLATE HRM1207JPD R CHIP METAL PLATE 1SB3052P-IC IC DAC IC ADC IC IC LCD CONTROLLER IC IC IC IC EEPROM IC IC SDRAM IC SDRAM IC SDRAM IC IC OSD FET CHIP IC CRYSTAL QUARTZ CRYSTAL

U015 1M62393P-U017 1TDA8752AH U019 1TC74ACT14 U1 U10 U11 U12 U16 U2 U3 U4 U5 U6 U7 U8 U9 Y1 Y2 1MX88281FC 1TC74ACT57 1TC74ACT57 1TC74ACT57 1AT24C21-1ZRC250N80 1KM416S102 1KM416S102 1KM416S102 1AT24C1610 1DW0SD05-TNDS9958-1TC74ACT57 5XJ14R318F 5XJ11R059E

HCTEJ220MC C CHIP TANTAL

SC10 HCTED221MC C CHIP TANTAL SC11 HCTED221MC C CHIP TANTAL SC12 HCTED221MC C CHIP TANTAL SC13 HCTED221MC C CHIP TANTAL SC18 HCTEJ220MC C CHIP TANTAL SC2 HCTEJ220MC C CHIP TANTAL

SC20 HCTBF100MB C CHIP TANTAL SC21 HCFF105ZEA C CHIP CERA SC3 SC4 SC5 SC6 SC7 SC8 SD1 HCTBF479MB C CHIP TANTAL HCFK104ZCA C CHIP CERA HCFK104ZCA C CHIP CERA HCFK103ZCA C CHIP CERA HCFK103ZCA C CHIP CERA HCFF105ZEA C CHIP CERA DKDS181RTK DIODE CHIP

38