Text preview for : RN15MSS+_SM.pdf part of Samsung SyncMaster 570BTFT COLOR MONITOR SyncMaster 570BTFT SyncMaster 580BTFT RN15MSS / RN15MST RN15MOS / RN15MOT Service Manual



Back to : RN15MSS+_SM.rar | Home

COLOR MONITOR
SyncMaster 570BTFT SyncMaster 580BTFT (RN15MSS / RN15MST RN15MOS / RN15MOT)

SERVICE
COLOR MONITOR

Manual
CONTENTS
1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Troubleshooting 5. Exploded View & Parts List 6. Electrical Parts List 7. Block Diagram

AUTO

EXIT

MENU

8. Wiring Diagram 9. Schematic Diagrams

Samsung Electronics Co., Ltd. September 1999 Printed in Korea Code No.: BN68-00084A

1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock.

1-1 Safety Precautions
1-1-1 Warnings
1. 2. 3. For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC Power Jack before servicing. When the chassis is operating, semiconductor heatsinks are potential shock hazards.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES (READING SHOULD NOT BE ABOVE 0.5mA)

LEAKAGE CURRENT TESTER

1-1-2 Servicing the LCD Monitor
1. When servicing the LCD Monitor, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead. (Disconnect the AC line cord from the AC outlet.) It is essential that service technicians have an accurate voltage meter available at all times. Check the calibration of this meter periodically.

2-WIRE CORD

ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

EARTH GROUND

2.

Figure 1-1. Leakage Current Test Circuit
4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.

1-1-3 Fire and Shock Hazard
Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

2.

1-1-4 Product Safety Notices
Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by ! on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.

3.

SyncMaster 570BTFT / 580BTFT

1-1

1 Precautions

1-2 Servicing Precautions
WARNING: Caution: Note: An electrolytic capacitor installed with the wrong polarity might explode. Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.

1-2-1 General Servicing Precautions
1. Always unplug the unit's AC power cord from the AC power source and disconnect the DC Power Jack before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect a test component in parallel with an electrolytic capacitor. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged. 4. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 6. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.

5.

2.

3.

1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs. Use only a grounded-tip soldering iron to solder or desolder ESDs. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESDs. 8. 6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

7.

2.

3.

Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.
Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.

4. 5.

1-2

SyncMaster 570BTFT / 580BTFT

2 Product Specifications
2-1 Specifications
Item LCD Panel Scanning Frequency Display Colors Maximum Resolution Input Video Signal Input Sync Signal Description TFT-LCD panel, RGB vertical stripe, normaly white, 15-Inch viewable, 0.297 (H) x 0.297 (V) pixel pitch Horizontal Vertical : : 30 kHz to 61 kHz (Automatic) 50 Hz to 75 Hz (Automatic)

16,772,216 colors Horizontal : 1024 Pixels Vertical : 768 Pixels Analog, 0.714 Vp-p ± 5% positive at 75 , internally terminated Type: Level: Seperate H/V sync, Composite H/V, Sync-on-Green, automatic synchronization without external switch of sync type TTL level

Maximum Pixel Clock rate Active Display Horizontal/Vertical

80 MHz 304.1 mm / 228.1 mm

AC power voltage & Frequency AC 90 to 264 Volts, 60/ 50 Hz ± 3 Hz Power Consumption Dimensions Unit (W x D x H) Carton (W x D x H) Weight (Net/Gross) Environmental Considerations 25 W (max.)

15.9x7.7x16.5 Inches (404 x 196 x 419 mm) 18.7 x 11.1 x 20.1 Inches (475 x 282 x 510 mm) 7.4 kg / 9.4kg Operating Temperature : 50°F to 104°F (10°C to 40°C) Humidity : 10 % to 80 % Storage Temperature : -13°F to 113°F (-25°C to 45°C) Humidity : 5 % to 95 %

Audio Characteristics (optional)

· Audio Characteristics · Built-in Microphone: High-sensitivity condenser microphone (mono) · Audio input: Left/Right Stereo phone jack, 0.7 Vrms · Sound output: 16 W (left) + 16 W (right)/THD 1% at 16ohm · Frequency response: 80 Hz~20 kHz (at ­3dB) · Headphone: Max 50mW output (3.5-pi jack) · Speaker: Internal semi Dome (16ohm x 2)

· SyncMaster 570BTFT/580BTFT complies with SWEDAC (MPR II) recommendations for reduced electromagnetic fields. · Designs and specifications are subject to change without prior notice.

SyncMaster 570BTFT / 580BTFT

2-1

2 Product Specifications

2-2 Pin Assignments
Sync Type Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Separate Red Green Blue GND GND (DDC Return) GND-R GND-G GND-B No Connection GND-Sync/Self Test GND DDC Data H-Sync V-Sync DDC Clock 15-Pin Signal Cable Connector Composite Red Green Blue GND GND (DDC Return) GND-R GND-G GND-B No Connection GND-Sync/Self Test GND DDC Data H/V-Sync Not Used DDC Clock Sync-on-green Red Green + H/V Sync Blue GND GND (DDC Return) GND-R GND-G GND-B Not Used GND-Sync/Self Test GND DDC Data Not Used Not Used DDC Clock

Sync Type Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ~26 Separate Red Green Blue GND GND (DDC Return) GND-R GND-G GND-B No Connection GND-Sync/Self Test GND DDC Data H-Sync V-Sync DDC Clock GND

26-Pin Signal Cable Connector Composite Red Green Blue GND GND (DDC Return) GND-R GND-G GND-B No Connection GND-Sync/Self Test GND DDC Data H/V-Sync Not Used DDC Clock GND Sync-on-green Red Green + H/V Sync Blue GND GND (DDC Return) GND-R GND-G GND-B Not Used GND-Sync/Self Test GND DDC Data Not Used Not Used DDC Clock GND

2-2

SyncMaster 570BTFT / 580BTFT

2 Product Specifications

2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Mode VGA1/70 Hz 640 x 350 31.469 31.778 3.813 1.589 26.058 0.318 70.086 14.268 0.064 1.716 11.504 0.985 25.175 IBM VGA2/70 Hz 720 x 400 31.469 31.777 3.813 1.589 26.058 0.318 70.087 14.268 0.064 0.858 13.155 0.191 28.322 VGA3/60 Hz 640 x 480 31.469 31.778 3.813 1.589 26.058 0.318 59.940 16.683 0.064 0.794 15.761 0.064 25.175 640/72 Hz 640 x 480 37.861 26.413 1.270 3.810 20.825 0.508 72.809 13.735 0.079 0.528 13.100 0.026 31.500 VESA 640/75 Hz 640 x 480 37.500 26.667 2.032 3.810 20.317 0.508 75.000 13.333 0.080 0.427 12.800 0.027 31.500 800/56 Hz 800 x 600 35.156 28.444 2.000 3.556 22.222 0.667 56.250 17.778 0.057 0.626 17.067 0.028 36.000 800/60 Hz 800 x 600 37.879 26.400 3.200 2.200 20.000 1.000 60.317 16.579 0.106 0.607 15.840 0.026 40.000

Timing fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock Frequency (MHz) Polarity H.Sync V.Sync Remark

Positive Negative Separate

Negative Positive Separate

Negative Negative Separate

Negative Negative Separate

Negative Negative Separate

Positive Negative Separate

Positive Positive Separate

Separate Sync
Horizontal
Video Video
CC

Vertical
Video Video DD E E
Q

Q

RR

S S

Sync Sync B B AA

Sync Sync

PP
O O

A : Line time total C : Back porch E : Front porch SyncMaster 570BTFT / 580BTFT

B : Horizontal sync width D : Active time

O : Frame time total Q : Back porch S : Front porch

P : Vertical sync width R : Active time

2-3

2 Product Specifications

Table 2-1. Timing Chart Continued Mode 800/72 Hz 800 x 600 48.077 20.800 2.400 1.280 16.000 1.120 72.188 13.853 0.125 0.478 12.480 0.770 50.000 800/75 Hz 800 x 600 46.875 21.333 1.616 3.232 16.162 0.323 75.000 13.333 0.064 0.448 12.800 0.021 49.500 VESA 1024/60 Hz 1024 x 768 48.363 20.677 2.092 2.462 15.754 0.369 60.004 16.666 0.124 0.600 15.880 0.062 65.000 1024/70 Hz 1024 x 768 56.476 17.707 1.813 1.920 13.653 0.320 70.069 14.272 0.106 0.513 13.599 0.053 75.000 1024/75 Hz 1024 x 768 60.023 16.660 1.219 2.235 13.003 0.203 75.029 13.328 0.050 0.466 12.795 0.017 78.750 MAC. 640/67 Hz 60 x 480 35.000 28.571 2.116 3.175 21.164 2.116 66.667 15.000 0.086 1.114 13.714 0.086 30.240 832/75 Hz 832 x 624 49.726 20.110 1.117 3.910 14.524 0.559 74.551 13.414 0.060 0.784 12.549 0.020 57.284

Timing fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock Frequency (MHz) Polarity H.Sync V.Sync Remark

Positive Positive Separate

Positive Positive Separate

Negative Negative Separate

Negative Negative Separate

Positive Positive Separate

Negative Negative Separate

Negative Negative Separate

Separate Sync
Horizontal
Video Video
CC

Vertical
Video Video DD E E
Q

Q

RR

S S

Sync Sync B B AA

Sync Sync

PP
O O

A : Line time total C : Back porch E : Front porch

B : Horizontal sync width D : Active time

O : Frame time total Q : Back porch S : Front porch

P : Vertical sync width R : Active time

2-4

SyncMaster 570BTFT / 580BTFT

3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the SyncMaster 570BTFT/580BTFT monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components.

3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly. 2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

3-1-1 Removing the Stand
1. Remove 4 screws in the hinge area. 2. Pry it off the back of the monitor. 3. Disconnect Power Cord and Signal Cable.

3. Remove Stand Front from the Stand assembly. 4. Remove 2 screws from the Stand assembly. 5. Remove the Stand Rear from the Stand assembly. 6. Remove 5 screws on the Vesa Brkt from the Stand assembly. 7. Remove cover hinge from the Stand assembly. 8. Remove Stand Base from the Stand assembly.

3-1-2 Main Body Disassembly
1. Remove the 4 screws on the four corner of the Rear Cover. 2. Remove Rear Cover from the Front Cover. 3. Remove 11 screws on the Shield and remove the shield. 4. Disconnect Inverter wire, Function PCB wire and Interface wire. Remove 4 screws on the Main PCB and remove 2 screws on the D sub shield. 5. Remove the Main PCB Assembly. 6. Remove 6 screws on the Inverter PCB Assembly and then remove it 7. Remove 6 screws on the Rear Panel Bracket. 8. Remove the Bracket Assembly from the Front Cover. 9. Remove 3 screws on the Function PCB from locking area of Function knob and remove Function PCB. 10. Remove 4 screws on the Shield of Panel. 11. Remove the Shield. 12. Remove Rear Bracket from Panel. 13. Remove 2 screws between Panel Rear and Inverter PCB. 14. Remove the Interface wire on the Rear Side of Panel.

3-1-4 Pivot Multi-media Stand Disassembly (option)
1. Stand the stand assembly with the base close to you. 2. Remove the 4 screws on the back cover of the stand and remove it. 3. Stand the stand assembly upside down. 4. Remove the 4 screws. 5. Disconnect CN805, CN806, CN807, CN808, CN809, CN812 and F1. 6. Remove the Back Cover of the Stand Front assembly. 7. Remove 4 screws on the external adaptor and remove the adaptor. 8. Remove 2 screws between hinge and Stand Body. 9. Remove the hinge 10. Remove 2 screws on Audio main PCB and remove it 11. Remove 2 screws on the Audio Function PCB and remove it.

3-1-5 Angle Pivot Stand Disassembly (option)
1. Remove the cap pivot from the stand assembly. 2. Remove the 4 screws on the hinge assembly. 3. Remove the 4 screws on the Stand Rear

3-1-3 Standard Stand Disassembly
1. Remove 5 screws from the Stand Rear 2. Remove 4 screws from the Stand Bottom.

SyncMaster 570BTFT / 580BTFT

3-1

3 Disassembly and Reassembly 4. Remove the Stand Rear from the Stand assembly. 5. Remove the Stand Front from the Stand assembly. 6. Remove the Neck Rear from the Stand assembly. 7. Remove the 4 Rubbers on the four corner of the Stand Bottom and the 4 screws on the four corner of the Stand Bottom.

3-1-6 Wire frame stand Disassembly (option)
1. Carefully pull the cover hinge. 2. Remove the cover vesa from the Stand assembly. 3. Remove 4 screws on the assembly Bracket assembly.

8. Remove the 5 stopper hings from the Bracket Bottom. 9. Remove the Stand Base from the Stand Assembly.

3-2 Replacement Order of Lamp Assemblies
- RN15MSS/RM15MOS (Samsung Panel)

3-2

SyncMaster 570BTFT / 580BTFT

3 Disassembly and Reassembly

SyncMaster 570BTFT / 580BTFT

3-3

3 Disassembly and Reassembly

3-3 Replacement Order of Lamp Assemblies
- RN15MST/RM15SOT (Toshiba Panel)

1. After confirm there is nothing on the desk Turn the LCD module over and put it on a flat desk set to the ground.

2. Push down the stopper and slide the lamp unit.

3. Please take out the lamp units from the LCD module.

3-4

SyncMaster 570BTFT / 580BTFT

3 Disassembly and Reassembly

4. Please fix the new lamp units on the LCD module : opposite process 2 and 3

*

Replacement of lamp unit should be done at the power off state and rcommended clean bench condition.

3-4 Reassembly
Reassembly procedures are in the reverse order of Disassembly procedures.

SyncMaster 570BTFT / 580BTFT

3-5

3 Disassembly and Reassembly

Memo

3-6

SyncMaster 570BTFT / 580BTFT

4 Troubleshooting
Notes: 1. Before troubleshooting, setup the PC's display as below. · Resolution: 1024 x 768 · H-frequency: 48 kHz · V-frequency: 60 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. · No raster appears: Audio PCB, SMPS PCB, Main PCB · 12V develop but no screen: Main PCB · 12V does not develop: Audio PCB, SMPS PCB 4. If you push and hold the "EXIT" button for more than 5 seconds, the monitor automatically turns back to the factory preset.

4-1 No Power
Does proper DC 12 V appear at DC jack connected to CN102? No Check SMPS PCB and CN816.

Yes

Does proper DC 5 V appear at Pin 3 of IC109?

No

Check FT100 and IC109.

Yes

Check IC401, IC111, Q101 and Q102.

SyncMaster 570BTFT/580BTFT

4-1

4 Troubleshooting

4-2 No Video
Power indicator is green

Does the clock pulse appear at output of R190, R191, R193?

No

7

Does the H-sync pulse appear at Pin 94 of IC101?

No

8

9

Does the pulse appear at Pin 10 of IC105 or Pin 1 of IC104? Yes

No

Yes Yes Replace IC101.

Replace IC106. Replace IC104 (SOG) or IC105 (seperate sync.

18 19

Does the sync pulses appear at Pins 20 and 22 of IC192?

No

20

1

Does the sync pulses appear at Pins 34 and 39 of IC192? Yes

No

Check IC101 and IC401.

Yes

Replace IC192 or check its related circuit.

2

3

4

5

Do the sync pulses appear at Pins 22, 23, 25 and 26 of IC310?

No

10

11

12

13

14

Do the sync pulses appear at Pins 2, 3, 54, 55 and 56 of IC301? Yes

No

Replace IC301 or check its related circuit.

Yes

Replace IC305 or check its related circuit. No Replace IC310 and IC311 or check its related circuits.

6

Do the waveforms appear at Pins 5 and 20 of CN301? Yes Replace LCD Panel

4-2

SyncMaster 570BTFT/580BTFT

4 Troubleshooting

WAVEFORMS
1 IC192 #39 2 IC310 #22 3 IC310 #23 4 IC310 #25

CH1 RMS = 3.6 V

CH1 RMS = 3.1 V

CH1 RMS = 2.3 V

CH1 RMS = 2.8 V

5 IC310 #26

6 CN301 #5~20

7 IC101 #94

8 IC105 #10

CH1 RMS = 2.12 V

CH1 RMS = 1.18 V

CH1 RMS = 3.5 V

CH1 RMS = 3.1 V

9 IC104, #1

10 IC301 #2

11 IC301 #3

12 IC301 #54

CH1 RMS = 4.56 V

CH1 RMS = 2.3 V

CH1 RMS = 3.25 V

CH1 RMS = 2.35 V

13 IC301, #55

14 IC301 #56

18 IC192 #20

19 IC192 #22

CH1 RMS = 200 mV

CH1 RMS = 50 mV

CH1 RMS = 1.24 V

CH1 RMS = 400 mV

20 IC192 #34

CH1 RMS = 4.4 V

SyncMaster 570BTFT/580BTFT

4-3

4 Troubleshooting

4-3 No Video of Alternate Vertical Line
One or more even or odd vertical lines do not display.

6

Does the waveform appear at Pin 20 of CN301? Yes Replace LCD panel.

No

Replace IC311 or check its related circuit.

WAVEFORMS
6 CN301 #20

CH1 RMS = 1.18 V

4-4 No OSD
WAVEFORMS
There is video but no OSD.
15 IC307 #12

15

While pushing a front control button does any pulse appear at Pin 12 of IC307? Yes Replace IC305.

No

16

Do sync signals appear at Pins 5 and 10 of IC307? 17 Yes Replace IC307 or check its related circuit. Replace IC305.

No
CH1 RMS = 2.2 V

16 IC307 #5

CH1 RMS = 1.7 V

17 IC307 #10

CH1 RMS = 4.3 V

4-5 User Controls Don't Work
Does the DC level change at Pins 11 and 12 of IC401 when you push the front panel button? Yes Go to 4-4 No OSD Display. 4-4 SyncMaster 570BTFT/580BTFT

No

Check the buttons. (SW861 ~ SW866)

4 Troubleshooting

4-6 No Sound

Does the DC 5 V appear at Pin 4 of IC803, Pin 5 of CN806? Yes Does the sound input signal appear at Pins 6 and 11 of IC803? Yes Do the sound signals appear at Pins 3 and 14 of IC803? Yes Does the DC 2.5 V bias appear at Pin 16 of IC503? Yes Check CN814, CN815 outputs.

No

Check IC803, IC804, VR841 and related circuit.

No

Check Pins 1 and 2 of CN806 and related circuits.

No

Check IC803 and related circuits.

No

Check C815, CN813, R821, R822, ZD803 on the Audio PCB.

SyncMaster 570BTFT/580BTFT

4-5

4 Troubleshooting

4-7 Microphones Don't Work

Does the PC's sound program operate well? Yes Is the connection between the PC and monitor secure? Yes Is the Internal Microphone connector attached? Yes Does the Internal Microphone work? Yes Does the External Microphone work? Yes OK

No

Check the PC's sound program and compatibility.

No

Connect the cable between the PC and monitor.

No

Check the connection between CN805 on the Audio PCB and the Internal Microphone.

No

Check Q802 and related circuits.

No

Check the CN182 jack.

4-8 Headphones Don't Work
Check CN813 on the Audio PCB and related circuit R817, R820, ZD801, ZD802.

Can you hear any sound from the Headphones? Yes Do you hear sound from the Internal Speaker? Yes OK 4-6

No

No

Check the Headphone Plug in the Headphone Jack and R821, R822, C815 on the Audio PCB.

SyncMaster 570BTFT/580BTFT

5 Exploded View & Parts List

5-2 Multimedia Pivot-base RN15MST (TOSHIBA PANEL)

5 Exploded View & Parts List

5-4 Multimedia-base RN15MST (TOSHIBA PANEL)

5 Exploded View & Parts List

5-6 Pivot-base RN15MST (TOSHIBA PANEL)

5 Exploded View & Parts List

5-8 Simple-base RN15MST (TOSHIBA PANEL)

5 Exploded View & Parts List

5-10 Wire frame-base RN15MST (TOSHIBA PANEL)

6 Electrical Parts List
6-1 Main PCB Parts
Loc. No. BD101 BD102 BD103 BD104 BD105 BD401 BD402 BD403 BD404 C100 C101 C102 C103 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C115 C116 C117 C118 C119 C120 C121 C122 C123 C124 C125 C126 C127 C128 C129 C130 C131 C132 C133 C134 C135 Code No. 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2703-001334 2203-000260 2402-000168 2203-000260 2402-000168 2203-000260 2402-000168 2402-000168 2203-000239 2203-000239 2203-000260 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2404-000123 2203-000260 2203-000204 2203-000260 2203-000204 2203-000260 2203-000204 2203-000260 2203-000609 2203-000260 2203-000609 2203-000260 2203-000609 2203-000151 2203-000260 2203-000260 2203-000260 2203-000260 2203-000260 2203-000260 2203-000260 Description INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP Specification 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 1.5uH,10%,2x1.25x0.85mm 10NF,10%,50V,X7R,TP,2012 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 10NF,10%,50V,X7R,TP,2012 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 10NF,10%,50V,X7R,TP,2012 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 0.1nF,5%,50V,NPO,TP,2012 0.1nF,5%,50V,NPO,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10uF,20%,16V,TP,6032,2.9mm 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 22NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 22NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 22NF,10%,50V,X7R,TP,2012 1.5nF,5%,50V,NPO,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 Remarks

SyncMaster 570BTFT/580BTFT

6-1

6 Electrical Parts List

Loc. No. C136 C137 C138 C139 C140 C141 C142 C143 C144 C145 C146 C147 C148 C149 C150 C151 C157 C158 C159 C160 C161 C163 C165 C167 C168 C169 C172 C173 C175 C176 C177 C180 C181 C182 C183 C184 C185 C186 C187 C188 C189 C190 C192 C193 C194 C195 C196

Code No. 2203-000260 2203-000204 2203-000260 2203-000204 2203-000260 2203-000204 2203-001391 2203-000455 2203-000204 2203-000260 2203-000260 2203-000204 2203-000260 2203-000204 2203-000260 2203-000204 2203-000204 2203-000204 2402-000168 2203-000204 2203-000204 2203-000260 2409-000124 2402-000168 2203-000260 2402-000168 2402-000168 2409-000124 2404-000123 2402-000168 2409-000124 2404-000123 2404-000123 2203-000260 2203-000204 2203-000260 2203-000204 2404-000123 2404-000123 2203-000204 2203-000260 2203-000204 2203-000151 2404-000123 2203-000260 2203-000260 2203-000260

Description C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-ORGANIC C-AL,SMD C-CERAMIC,CHIP C-AL,SMD C-AL,SMD C-ORGANIC C-TA,CHIP C-AL,SMD C-ORGANIC C-TA,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP

Specification 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 150nF,10%,25V,X7R,TP,2012 1nF,5%,50V,NPO,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100uF,10%,16V,LZ,BK,8x10.5,3.5 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 10NF,10%,50V,X7R,TP,2012 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 100uF,10%,16V,LZ,BK,8x10.5,3.5 10uF,20%,16V,TP,6032,2.9mm 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 100uF,10%,16V,LZ,BK,8x10.5,3.5 10uF,20%,16V,TP,6032,2.9mm 10uF,20%,16V,TP,6032,2.9mm 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10uF,20%,16V,TP,6032,2.9mm 10uF,20%,16V,TP,6032,2.9mm 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 1.5nF,5%,50V,NPO,TP,2012 10uF,20%,16V,TP,6032,2.9mm 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012

Remarks

6-2

SyncMaster 570BTFT/580BTFT

6 Electrical Parts List

Loc. No. C197 C198 C199 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 C324 C325 C326 C327 C328 C329 C330 C331 C332 C333 C334 C335 C336 C337 C338 C339 C340 C341 C342 C343 C344

Code No. 2203-000683 2203-000683 2203-000683 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-001723 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204

Description C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP

Specification 27pF,5%,50V,NPO,TP,2012 27pF,5%,50V,NPO,TP,2012 27pF,5%,50V,NPO,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 4.7pF,5%,50V,NPO,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012

Remarks

SyncMaster 570BTFT/580BTFT

6-3

6 Electrical Parts List

Loc. No. C345 C346 C347 C348 C349 C350 C351 C352 C353 C354 C355 C356 C357 C358 C359 C360 C361 C363 C364 C365 C367 C368 C369 C370 C371 C372 C389 C390 C401 C402 C403 C404 C405 C407 C408 C409 C410 C411 C412 C413 C414 C415 C416 C417 C473 C474 C496

Code No. 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000260 2404-000123 2203-000204 2203-000818 2203-000818 2404-000151 2404-000151 2404-000123 2203-000260 2203-000204 2203-000204 2203-000260 2404-000123 2203-000260 2404-000123 2203-000455 2203-000204 2402-000168 2404-000123 2203-000260 2203-000204 2404-000123 2203-000555 2203-000555 2404-000123 2203-000260 2203-000239 2404-000123 2203-000204 2203-000260

Description C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-TA,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-AL,SMD C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP

Specification 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10uF,20%,16V,TP,6032,2.9mm 100NF,10%,25V,X7R,TP,2012 0.033nF,5%,50V,NPO,TP,2012 0.033nF,5%,50V,NPO,TP,2012 1uF,20%,16V,TP,3216 1uF,20%,16V,TP,3216 10uF,20%,16V,TP,6032,2.9mm 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10uF,20%,16V,TP,6032,2.9mm 10NF,10%,50V,X7R,TP,2012 10uF,20%,16V,TP,6032,2.9mm 1nF,5%,50V,NPO,TP,2012 100NF,10%,25V,X7R,TP,2012 100uF,20%,16V,GP,TP,8.3x8.3x6.3mm 10uF,20%,16V,TP,6032,2.9mm 10NF,10%,50V,X7R,TP,2012 100NF,10%,25V,X7R,TP,2012 10uF,20%,16V,TP,6032,2.9mm 20pF,5%,50V,NPO,TP,2012 20pF,5%,50V,NPO,TP,2012 10uF,20%,16V,TP,6032,2.9mm 10NF,10%,50V,X7R,TP,2012 0.1nF,5%,50V,NPO,TP,2012 10uF,20%,16V,TP,6032,2.9mm 100NF,10%,25V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012

Remarks

6-4

SyncMaster 570BTFT/580BTFT

6 Electrical Parts List

Loc. No. C497 C498 C499 C501 C502 C509 C510 C511 C512 CFT301 CFT317 CFT318 CL101 CL102 CN101 CN102 CN103 CN301 CN401 CN402 D101 D102 D103 D109 D113 D114 D402 D404 FT100 FT101 FT102 FT103 FT120 FT122 FT301 FT306 FT313 FT314 FT316 FT317 FT318 FT319 FT321 FT322 FT323 FT324 FT325

Code No. 2203-000260 2203-000260 2203-000260 2404-000123 2203-000455 2404-000123 2203-000455 2404-000123 2203-000455 2901-001115 2901-001112 2901-001115 BN27-20001C BN27-20001A 3701-001129 3722-000117 3711-000556 3711-003161 3711-002049 3711-000056 0401-001056 0401-001056 0401-001056 0401-001056 0402-000553 0402-000553 0401-001056 0401-001056 3301-001145 2901-001114 2901-001114 2901-001114 2901-001114 2901-000172 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001113 2901-001113 2901-001113 2901-001113 2901-001113

Description C-CERAMIC,CHIP C-CERAMIC,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP C-TA,CHIP C-CERAMIC,CHIP FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD COIL-SMD COIL-CHOKE CONNECTOR-DSUB JACK-DC POWER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING CORE-FERRITE BEAD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI ON BOARD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD

Specification 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10NF,10%,50V,X7R,TP,2012 10uF,20%,16V,TP,6032,2.9mm 1nF,5%,50V,NPO,TP,2012 10uF,20%,16V,TP,6032,2.9mm 1nF,5%,50V,NPO,TP,2012 10uF,20%,16V,TP,6032,2.9mm 1nF,5%,50V,NPO,TP,2012 50VDC,500mADC,20pF,3.1x1.6x2 50VDC,1.0ADC,85pF+-20%,3.2x1 50VDC,500mADC,20pF,3.1x1.6x2

Remarks

15P,3R,FEMALE,ANGLE,AUF 3P,3.5mm,AG,BLK,NO BOX,12P,1R,1.25mm,SMD-A,SN BOX,20P,1R,1.25mm,ANGLE,SN BOX,6P,1R,1.25mm,SMD-A,SN BOX,2P,1R,2.5mm,ANGLE,SN MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP SS24,40V,2.0A,DO-214AA SS24,40V,2.0A,DO-214AA MMBD4148SE,75V,600mA,SOT-23,TP MMBD4148SE,75V,600mA,SOT-23,TP AB,4.5x1.6x1.6mm,25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 50V,10A,-,12x11x13mm,BK 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,0.2A,35pF+-20%,2x1.25x

SyncMaster 570BTFT/580BTFT

6-5

6 Electrical Parts List

Loc. No. FT326 FT327 FT328 FT329 FT330 FT336 FT415 FT521 FT529 FT531 IC101 IC102 IC103 IC104 IC105 IC106 IC107 IC108 IC109 IC111 IC115 IC151 IC192 IC301 IC302 IC303 IC304 IC305 IC307 IC309 IC401 IC401_SOCK IC402 IC403 IC404 IC406 IC501 L102 L151 L152 L160 L170 L171 L172 L193

Code No. 2901-001113 2901-001113 2901-001113 2901-001113 2901-001113 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 1002-001099 1203-001488 1203-001488 1204-000292 0803-000117 0803-000122 1203-001448 1203-001447 1203-001488 0505-000275 1203-001538 0803-000275 BN13-00002A 1205-001407 1105-001165 1105-001165 1105-001165 0904-001222 BN09-00001A 0505-001170 0903-001063 3704-001071 1203-001109 1103-001164 1103-001023 0803-000122 1205-001740 2703-001070 2703-001070 2703-001070 2703-001070 2703-001070 2703-001070 2703-001070 2703-001070

Description FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD FILTER-EMI SMD IC-A/D CONVERTER IC-POSI.FIXED REG. IC-POSI.FIXED REG. IC-VIDEO SYSTEM IC-TTL IC-TTL IC-POSI.FIXED REG. IC-POSI.FIXED REG. IC-POSI.FIXED REG. FET-SILICON IC-POSI.ADJUST REG. IC-TTL IC-ASIC IC-BUFFER IC-DRAM IC-DRAM IC-DRAM IC-GRAPHIC CONT. IC-OSD PROCESSOR FET-SILICON IC-MICROCONTROLLER SOCKET-IC IC-VOL. DETECTOR IC-EEPROM IC-EEPROM IC-TTL IC-TRANSMITTER INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD

Specification 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,0.2A,35pF+-20%,2x1.25x 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 25VDC,2.0ADC,100nF,3.2x1.6x1 TDA8752,8BIT,QFP,100P,+-0.5, 7805,T0-252,3P,PLASTIC,4.8/5 7805,T0-252,3P,PLASTIC,4.8/5 LM1881M,SOP,8P,150MIL,PLASTIC, 74F14,INVERTER,SOP,14P,150MIL, 74F125,BUFFER,SOP,14P,150MIL,Q 2596,TO-263,5P,PLASTIC,4.750 2596,TO-263,5P,PLASTIC,3.135 7805,T0-252,3P,PLASTIC,4.8/5 SI4435DY,P,-30V,+-8.0A,0.02ohm 431,SOT-89,3P,PLASTIC,2.47/3 74F32,OR GATE,SOP,14P,150MIL,Q XB(LCD),FG60A018HM_L18,QFP,48P,AUTO GMFC1,QFP,208P,PLASTIC,3.6V, 416S1020,512Kx16BITx2,TSOP,50P 416S1020,512Kx16BITx2,TSOP,50P 416S1020,512Kx16BITx2,TSOP,50P GMZ1,QFP,208P,65MHz,TR,P LCD,MTV121P-31,16P SI9933ADY-T1,P,-20V,3.4A,0.075OHM,2W,SO-8 72E75,8BIT,DIP,42P,600MIL,24MH 42P,DIP,SN,1.778mm 7045,SOT-89,3P,PLASTIC,4.3/4 24LC21A,128X8BIT,SOP,8P,150MIL,5V,10%, PLASTIC,0 TO +70C,100UA,CMOS,TP 24C08,1028x8BIT,SOP,8P,150MIL, 74F125,BUFFER,SOP,14P,150MIL,Q DS90C385,TSSOP,56P,240MIL,PLASTIC,4V, 1.63W,10 TO +70C,ST,FPD LINK-85MHZ(LVDS) 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm

Remarks

6-6

SyncMaster 570BTFT/580BTFT

6 Electrical Parts List

Loc. No. L403 L406 L407 Q101 Q102 Q301 Q302 Q401 Q402 R101 R102 R103 R104 R105 R106 R107 R110 R115 R116 R117 R124 R125 R127 R129 R130 R131 R134 R136 R137 R138 R139 R142 R143 R190 R191 R192 R193 R194 R195 R196 R197 R198 R199 R301 R302 R303 R305

Code No. 2703-001070 2703-001070 2703-001070 0501-002080 0501-002080 0501-002080 0501-002080 0501-002080 0501-002080 2007-001166 2007-001166 2007-001166 2007-000781 2007-000781 2007-000781 2007-000493 2007-000290 2007-000593 2007-000593 2007-000023 2007-000593 2007-000593 2007-000300 2007-000822 2007-000290 2007-000290 2007-000468 2007-000872 2007-000872 2007-000872 2007-000221 2007-000872 2007-000221 2007-000029 2007-000029 2007-001113 2007-000593 2007-000872 2007-000572 2007-000468 2007-000029 2007-000029 2007-000029 2007-000468 2007-000468 2007-000290 2007-000468

Description INDUCTOR-SMD INDUCTOR-SMD INDUCTOR-SMD TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP

Specification 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 100uH,10%,4.5x3.2x3.2mm 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 2SC2412K,NPN,200mW,SOT-23,TP,1 75OHM,5%,1/10W,DA,TP,2012 75OHM,5%,1/10W,DA,TP,2012 75OHM,5%,1/10W,DA,TP,2012 33OHM,5%,1/10W,DA,TP,2012 33OHM,5%,1/10W,DA,TP,2012 33OHM,5%,1/10W,DA,TP,2012 2.2KOHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 22OHM,5%,1/10W,DA,TP,2012 22OHM,5%,1/10W,DA,TP,2012 120OHM,5%,1/10W,DA,TP,2012 22OHM,5%,1/10W,DA,TP,2012 22OHM,5%,1/10W,DA,TP,2012 10KOHM,5%,1/10W,DA,TP,2012 390OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 1.2KOHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 1.2KOHM,5%,1/10W,DA,TP,2012 0OHM,5%,1/10W,DA,TP,2012 0OHM,5%,1/10W,DA,TP,2012 680KOHM,5%,1/10W,DA,TP,2012 22OHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 220OHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012 0OHM,5%,1/10W,DA,TP,2012 0OHM,5%,1/10W,DA,TP,2012 0OHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012

Remarks

SyncMaster 570BTFT/580BTFT

6-7

6 Electrical Parts List

Loc. No. R306 R307 R308 R310 R311 R312 R314 R316 R317 R321 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R412 R413 R414 R415 R416 R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R427 R429 R431 R432 R433 R436 R437 R438 R439 R440 R441 R442

Code No. 2007-000290 2007-000290 2007-000282 2007-000300 2007-000282 2007-000300 2007-000593 2007-000766 2007-000572 2007-000468 2007-000941 2007-000941 2007-000941 2007-000941 2007-000941 2007-000872 2007-000941 2007-000941 2007-000941 2007-000872 2007-000872 2007-000872 2007-000941 2007-000941 2007-000941 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-001166 2007-000290 2007-000290 R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP

Description

Specification 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100KOHM,5%,1/10W,DA,TP,2012 10KOHM,5%,1/10W,DA,TP,2012 100KOHM,5%,1/10W,DA,TP,2012 10KOHM,5%,1/10W,DA,TP,2012 22OHM,5%,1/10W,DA,TP,2012 330OHM,5%,1/10W,DA,TP,2012 220OHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 4.7KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 75OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012

Remarks

6-8

SyncMaster 570BTFT/580BTFT

6 Electrical Parts List

Loc. No. R443 R444 R445 R447 R448 R449 R451 R452 R453 R454 R455 R456 R457 R458 R459 R460 R461 R462 R463 R464 R465 R466 R467 R470 RA101 RA102 RA103 RA104 RA105 RA106 RA107 RA108 RA109 RA110 RA111 RA112 RA301 RA302 RA303 RA304 RA305 SW301 SW301_S X301 X302 X401 ZD101

Code No. 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000468 2007-000822 2007-000468 2007-000941 2007-000290 2007-000477 2007-000572 2007-000290 2007-000290 2007-000409 2007-000409 2007-000290 2007-000290 2007-000290 2007-000468 2007-000941 2007-000023 2007-000931 2007-000941 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 2011-001015 2011-001015 2011-001015 2011-001015 2011-001015 2011-001015 2011-000002 2011-000002 2011-000002 2011-000002 2011-000002 BH39-40305U 3710-000001 2804-001217 2804-001164 2801-003326 0403-000579

Description R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-CHIP R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK R-NETWORK CBF HARNESS CONNECTOR-SHUNT OSCILLATOR-CLOCK OSCILLATOR-CLOCK CRYSTAL-SMD DIODE-ZENER

Specification 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012 390OHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 1MOHM,5%,1/10W,DA,TP,2012 220OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 15KOHM,5%,1/10W,DA,TP,2012 15KOHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 100OHM,5%,1/10W,DA,TP,2012 1KOHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 120OHM,5%,1/10W,DA,TP,2012 470OHM,5%,1/10W,DA,TP,2012 47KOHM,5%,1/10W,DA,TP,2012 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 1Kohm,5%,1/16W,L,CHIP,8P,TP 1Kohm,5%,1/16W,L,CHIP,8P,TP 1Kohm,5%,1/16W,L,CHIP,8P,TP 1Kohm,5%,1/16W,L,CHIP,8P,TP 1Kohm,5%,1/16W,L,CHIP,8P,TP 1Kohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP 22ohm,5%,1/16W,L,CHIP,8P,TP ,52MM,AWG22(0.6PI) 2P,1R,2.54mm,SN 67MHz,100ppm,10TTL & CMOS(30pF 85MHz,100ppm,10TTL(15pF),ST,3 24MHz,30ppm,28-ABX,16pF,50ohm BZX84C5V1,5.1V,5%,200mW,SOT-23

Remarks

SyncMaster 570BTFT/580BTFT

6-9

6 Electrical Parts List

Loc. No. ZD102 ZD103 ZD104 ZD105 ZD401

Code No. 0403-000579 0403-000579 0403-000579 0403-000579 0403-000579

Description DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER DIODE-ZENER

Specification BZX84C5V1,5.1V,5%,200mW,SOT-23 BZX84C5V1,5.1V,5%,200mW,SOT-23 BZX84C5V1,5.1V,5%,200mW,SOT-23 BZX84C5V1,5.1V,5%,200mW,SOT-23 BZX84C5V1,5.1V,5%,200mW,SOT-23

Remarks

6-10

SyncMaster 570BTFT/580BTFT

6 Electrical Parts List

7-2 Sub PCB Parts
Loc. No. CN801 OP801 R801 R802 R803 SW801 SW802 SW803 SW804 SW805 SW806 Code No. 3711-002050 0601-001047 2007-000300 2007-000301 2007-000302 3404-000243 3404-000244 3404-000245 3404-000246 3404-000247 3404-000248 Description slcon12p, CONNECTOR-HEADER 2_led, LED res, R-CHIP res, R-CHIP res, R-CHIP sw_tact2p, SWITCH-TACT sw_tact2p, SWITCH-TACT sw_tact2p, SWITCH-TACT sw_tact3p, SWITCH-TACT sw_tact4p, SWITCH-TACT sw_tact5p, SWITCH-TACT Specification BOX,10P,1R,1.25mm,SMD-A,SN ROUND,GRN/YEL,2mm,585nm 10Kohm,5%,1/10W,DA,TP,2012 10Kohm,5%,1/10W,DA,TP,2013 10Kohm,5%,1/10W,DA,TP,2014 15V,20mA,160gf+-50gf,6x3.5mm,S 15V,20mA,160gf+-50gf,6x3.6mm,S 15V,20mA,160gf+-50gf,6x3.7mm,S 15V,20mA,160gf+-50gf,6x3.8mm,S 15V,20mA,160gf+-50gf,6x3.9mm,S 15V,20mA,160gf+-50gf,6x3.10mm,S Remarks

Others
Loc. No. LCD P/CORD S/CABLE PROCESS-PBA UNIT B/D ASS'Y CODE Code No. BN07-00005A BH39-10307X BN39-00030A BN94-00014C BN98-00005C Description LCD-PANNEL CBF-POWER/CORD CBF-SIGNAL ASSY,PCB-ST ASSY,PCB/MAIN-ST Specification LTM150XS-L02,331.3*257.9*15.9,TN VERTICAL STRIPE,0.297*0.297 DET,H05VV-F,250V/6A,IVY,1830MM DETACHABLE,1830MM,15P/15P,2990,D-SUB-MALE RN15MS-XGD1/0000,EDC,EUROPE RN15MS-XGD1/0000,EDC,EUROPE

SyncMaster 570BTFT/580BTFT

6-11

6 Electrical Parts List

Memo

6-12

SyncMaster 570BTFT/580BTFT

7 Block Diagram

SyncMaster 570BTFT/580BTFT

H V H
8 8 8

MICOM and CONTROL PART

H GMFC1
R G B 8 8 8

DOT_CLK GMZ1
R G B 6 6 6

V LVDS x2

R

TDA8752

G
H/V/DOT_CLK
FRAME MEMORY

R G B H/V/EN/ DOT_CLK

TFT LCD PANEL

B

DOT_CLK

12V

VOLUME TONE CTRL.

LM4863 (Audio Amp) Speaker
(SyncMaster 330TFT/530TFT)

+5 V_S +3.3 V_S VCC +5 V_PLL +5 V_ADL

7-1

7 Block Diagrams

Memo

7-2

SyncMaster 570BTFT/580BTFT

8 Wiring Diagram

1 2 1 2

RIGHT ­ RIGHT + LEFT ­ LEFT +

CN814

CN806

CN815

LEFT_AMP RIGHT_AMP GND MIC_EN 5V 5V LEFT_IN RIGHT_IN

1 2 3 4 5 6 7 8

8 7 6 5 4 3 2 1

LEFT_AMP RIGHT_AMP GND MIC_EN 5V 5V LEFT_IN RIGHT_IN

CN841

LIVE GND NEUTRAL

AUDIO FUNC PCB

CN801

1 2 3

CN805 1 2 3 4 5 LIVE NC GND NC NEUTRAL GND 12 V

MIC_GND MIC_SIG

1 2 C-MIC

1 2

CN816

CN804

CN808

CN809

CN812

CN813

MIC_OUT

PC_AUDIO

EXT_MIC HEADPHONE

SMPS

1 2 3

CN101

LCD PANEL

NC BRIGHT NC BL_EN NC GND 5V GND GND 10 12V 11 12V 12 NS 1 2 3 4 5 6 7 8 9

CN102 CN103

5V (15":12V) 5V (15":12V) GND CN301 GND

CN401 LVDS_DATA

KEY VCC LED KEY2 GND GND

1 2 3 4 5 6

1 2 3 4 5 6

KEY VCC LED KEY2 GND GND

LED

CN861

CN862

SyncMaster 570BTFT/580BTFT

1 2 3 3 5 ~ 20

MAINFUNC PCB

VCC GND PWR

1 2 3 4

1 LED 2 VCC 3 GND 4 PWR

MAIN PCB

PC_R_IN PC_G_IN PC_B_IN GND S_RASTER GND SDA H_SYNC V_SYNC SCL

1 2 3 4~9 10 11 12 13 14 15 GND 16 ~26

1 PC_R_IN 2 PC_G_IN 3 PC_B_IN 4~9 GND 10 S_RASTER 11 GND 12 SDA 13 H_SYNC 14 V_SYNC 15 SCL

GND

12 V 12 V

CN101

POWER PCB
CN881

8-1

SyncMaster 570BTFT/580BTFT

9-2

SyncMaster 570BTFT/580BTFT

9-4

11 12 13 14 15 16 17 18 19 20 21

5 NC 5 5 Pulse Pulse 5 NC NC Pulse Pulse

32 33 34 35 36 37 38 39 40 41 42

Clock Clock 5 NC 3.8 5 0 5 5 GND NC

Unit: Vrms Table 9-8. IC403
pin # MODES 1024 x 768 / 75 Hz NC NC NC GND 4.43 4.46 4.87 5.03

1 2 3 4 5 6 7 8

Unit: Vrms

Table 9-9. IC404
pin # MODES 1024 x 768 / 75 Hz GND GND GND GND 5.03 5.03 GND 5.03

1 2 3 4 5 6 7 8

Unit: Vrms

SyncMaster 570BTFT/580BTFT