Text preview for : service mode.pdf part of meteoro rx100 The eletronic system of this cube
Back to : service mode.pdf | Home
ServiceMode 3.71 by stef_no1
Manufacturer
Akai
e-mail: [email protected]
Product
CTV
This is ServiceModeWare. If you find this usefull send me 2 new service modes.
Model
CT-2119
Chassis
Mode
Test Mode
Enter
Simultaneous press + & - on local panel and then power on with main switch. Exit: POWER. OFF: Select programm 38. Simultaneous press (3 sec) STORE & CONTROL+ on local keyboard. ON: Select programm 38. Simultaneous press (3 sec) STORE & PROGRAM- on local keyboard. Press UP & DOWN buttons together on tv's local control and then switch on. You will see SERVICE MODE. Do not press any button, just power off the set, then on. Press UP & DOWN buttons together on tv's local control and then switch on. Simultaneous press P+ & P- on local panel and then power on with main switch. Press button P/C on RC and switch on TV with main switch. Press button 'i' on RC and switch on TV with main switch.
Allstar
3750
CTV
Hotel Mode
AudioTon
CTV 5502
10.3 90° MONO
CTV
Child Lock Clear Service Mode Service Mode ATS Hotel Mode Cancel
AudioTon Beko Blaupunkt Blaupunkt
CTV 5502
10.3 90° MONO
CTV CTV
MM63-13VT MM63-13VT
FM240.00 FM240.00
CTV CTV
Brandt
ICC9
CTV
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED Service Mode switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again. (WARNING: scart must be free.) Service Mode Press and hold P+ and P- on local panel, then switch on TV with main switch.
Continental
CT1412B
CTV
Ferguson
ICC9
CTV
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED Service Mode switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again. (WARNING: scart must be free.) Put TV into standby, then turn power off, then turn power on whilst holding standby button on remote and step through menus to `vol set` and increase level to max. MUTE --> OK (M) --> TV Controls: cursor buttons. Store: OK (M). Exit: TV Simultaneously press MENU, VOL-, PR- on the local panel. Turn on 'TV Internal Service Program' switch on the digital modul (SE on display). On RC: 1=U1 V SHIFT, 2=U2 V LIN DN, 3=U3 V LIN, 4=H1 H SHIFT, 5=H2 H AMP, 6=H3 EW AMP, 7= C, 8=C1, 9=C2, 0=H4 EW TRAPEZ... TV=MEMO, VOL+/-=ADJUST. Press VOL+, VOL-, PR-, PR+, OK.
Ferguson
TX92
CTV
Hotel Mode Cancel
Finlux GoldStar
17/21B60 63/71Y2
STEREO PLUS MC-51B
CTV CTV
Service Mode Service Mode
Graetz
BURGGRAF STEREO 4876 Digivision
DIGI III 110°
CTV
Service Mode
Grundig
CUC1800
CTV
Child Lock Cancel
Manufacturer
Grundig
Model
Chassis
CUC1800
Product
CTV
Mode
EPROM Version Nr. Service Mode ATS Reset Child Lock Cancel Default Values Entering
Enter
Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Special functions', 'Service', 'Code 8500'. Press and hold button VOL+ on the TV and switch the mains button ON. ATS bit is set. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the button 'P-' on the RC while switching on with the mains button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Press 'i'. Dialog Center --> Service --> 'for authorized dealer' --> Code Number 8500. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. General reset with number 7038. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Special functions', 'Service', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Special functions', 'Service', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK.
Grundig Grundig Grundig
CUC1800 CUC1805 CUC1805
CTV CTV CTV
Grundig
CUC1805
CTV
Grundig
CUC1805
CTV
EPROM Version Nr. Service Mode Volume Offset Cancel Child Lock Cancel
Grundig Grundig Grundig
CUC1805 CUC1805 CUC1806
CTV CTV CTV
Grundig
CUC1806
CTV
Demo Mode
Grundig
CUC1806
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel EPROM Version Nr. Service Mode Child Lock Cancel EPROM Version Nr. Service Mode Child Lock Cancel
Grundig
CUC1806
CTV
Grundig Grundig
CUC1806 CUC1821
CTV CTV
Grundig
CUC1821
CTV
Grundig Grundig
CUC1821 CUC1822
CTV CTV
Grundig
CUC1822
CTV
Grundig Grundig
CUC1822 CUC1824
CTV CTV
Manufacturer
Grundig
Model
Chassis
CUC1824
Product
CTV
Mode
EPROM Version Nr. Service Mode ATS Reset Child Lock Cancel EPROM Version Nr.
Enter
Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Special functions', 'Service', 'Code 8500'. Press and hold button VOL+ on the TV and switch the mains button ON. ATS bit is set. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Press and hold the P- buton on the TV and switch on with the mains button. Loading the Average Values / Emergency Data Set (ROM Dana). This is only possible once on replacement of the NVM or uP. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. Press and hold button VOL+ on the TV and switch the mains button ON. ATS bit is set. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Press and hold the P- buton on the TV and switch on with the mains button. Loading the Average Values / Emergency Data Set (ROM Dana). This is only possible once on replacement of the NVM or uP. Press 'i'. Dialog Center --> Service --> 'for authorized dealer' --> Code Number 8500. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the button 'P-' on the RC while switching on with the mains button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. General reset with number 7038.
Grundig Grundig Grundig
CUC1824 CUC1825 CUC1825
CTV CTV CTV
Grundig
CUC1825
CTV
Grundig
CUC1825
CTV
ROM Data Loading
Grundig Grundig Grundig Grundig
CUC1825 CUC1825 CUC1826 CUC1826
CTV CTV CTV CTV
Service Mode Volume Offset Cancel ATS Reset Child Lock Cancel EPROM Version Nr.
Grundig
CUC1826
CTV
Grundig
CUC1826
CTV
ROM Data Loading
Grundig Grundig Grundig
CUC1826 CUC1826 CUC1827
CTV CTV CTV
Service Mode Volume Offset Cancel Child Lock Cancel Default Values Entering
Grundig
CUC1827
CTV
Grundig
CUC1827
CTV
EPROM Version Nr. Service Mode Volume Offset Cancel Child Lock Cancel
Grundig Grundig Grundig
CUC1827 CUC1827 CUC1828
CTV CTV CTV
Manufacturer
Model
Chassis
Product
Mode
Enter
Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. General reset with number 7038. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. General reset with number 7038. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. General reset with number 7038. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button).
Grundig
CUC1828
CTV
Demo Mode
Grundig
CUC1828
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Grundig
CUC1828
CTV
Grundig Grundig
CUC1828 CUC1829
CTV CTV
Grundig
CUC1829
CTV
Demo Mode
Grundig
CUC1829
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Grundig
CUC1829
CTV
Grundig Grundig
CUC1829 CUC1830
CTV CTV
Grundig
CUC1830
CTV
Demo Mode
Grundig
CUC1830
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Grundig
CUC1830
CTV
Grundig Grundig
CUC1830 CUC1836
CTV CTV
Grundig
CUC1836
CTV
Demo Mode
Manufacturer
Grundig
Model
Chassis
CUC1836
Product
CTV
Mode
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Enter
Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Special functions', 'Service', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Special functions', 'Service', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Special functions', 'Service', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Menu guide: 'i', 'Special functions', 'Service', 'Code 8500'.
Grundig
CUC1836
CTV
Grundig Grundig
CUC1836 CUC1842
CTV CTV
Grundig
CUC1842
CTV
Demo Mode
Grundig
CUC1842
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel EPROM Version Nr. Service Mode Child Lock Cancel EPROM Version Nr. Service Mode Child Lock Cancel EPROM Version Nr. Service Mode Child Lock Cancel EPROM Version Nr. Service Mode
Grundig
CUC1842
CTV
Grundig Grundig
CUC1842 CUC1851
CTV CTV
Grundig
CUC1851
CTV
Grundig Grundig
CUC1851 CUC1852
CTV CTV
Grundig
CUC1852
CTV
Grundig Grundig
CUC1852 CUC1881
CTV CTV
Grundig
CUC1881
CTV
Grundig Grundig
CUC1881 CUC1892
CTV CTV
Grundig
CUC1892
CTV
Grundig
CUC1892
CTV
Manufacturer
Grundig
Model
Chassis
CUC1894
Product
CTV
Mode
Child Lock Cancel
Enter
Press VOL+, VOL-, PR-, PR+, OK. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. General reset with number 7038. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK.
Grundig
CUC1894
CTV
Demo Mode
Grundig
CUC1894
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Grundig
CUC1894
CTV
Grundig Grundig
CUC1894 CUC1929
CTV CTV
Grundig
CUC1929
CTV
Demo Mode
Grundig
CUC1929
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Grundig
CUC1929
CTV
Grundig Grundig
CUC1929 CUC1952
CTV CTV
Grundig
CUC1952
CTV
Demo Mode
Grundig
CUC1952
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Grundig
CUC1952
CTV
Grundig Grundig
CUC1952 CUC1962
CTV CTV
Manufacturer
Model
Chassis
Product
Mode
Enter
Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Demo on: Depress and hold button 'L+' on the TV and switch the TV on with the mains button. Press the 'P+' button within a time of 10s. Demo off: ATS Reset (by depressing the 'L+' button on the TV while switching on with the mains button). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Buttons 'AUX', 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Depress and hold button 'i' on the RC while switching on with the mains button. Move the bar to 'AGC' in the Service Menu and operate the buttons 'AUX', 'OK' in this order. General reset with number 7038.
Grundig
CUC1962
CTV
Demo Mode
Grundig
CUC1962
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Grundig
CUC1962
CTV
Grundig Grundig
CUC1962 CUC1983
CTV CTV
Grundig
CUC1983
CTV
Demo Mode
Grundig
CUC1983
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Child Lock Cancel
Grundig
CUC1983
CTV
Grundig Grundig
CUC1983 CUC1984
CTV CTV
Grundig
CUC1984
CTV
Demo Mode
Grundig
CUC1984
CTV
EPROM Version Nr. Factory Default Values Resetting Service Mode Band Limits Cancelling Child Lock Cancel
Grundig
CUC1984
CTV
Grundig
CUC1984
CTV
Grundig
CUC2020
CTV
Grundig
CUC2020
CTV
Manufacturer
Model
Chassis
Product
Mode
Enter
Depress and hold the button 'P-' on the RC while switching on with the mains button. (Additionally on replacement of the memory, the Hotel Mode and the band limits are to be deactivated and the AGC and AFC are to be readjusted).
Grundig
CUC2020
CTV
Default Values Entering
Grundig
CUC2020
CTV
Hotel Mode
Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Depress and hold button 'i' on the RC while switching on with the mains button. Move the bar to 'AGC' in the Service Menu and operate the buttons 'AUX', 'OK' in this order. General reset with number 7038. Depress and hold the button 'P-' on the RC while switching on with the mains button. (Additionally on replacement of the memory, the Hotel Mode and the band limits are to be deactivated and the AGC and AFC are to be readjusted).
Grundig Grundig
CUC2020 CUC2020
CTV CTV
OSD position Service Mode Band Limits Cancelling Child Lock Cancel
Grundig
CUC2030
CTV
Grundig
CUC2030
CTV
Grundig
CUC2030
CTV
Default Values Entering
Grundig
CUC2030
CTV
Hotel Mode
Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Depress and hold button 'i' on the RC while switching on with the mains button. Move the bar to 'AGC' in the Service Menu and operate the buttons 'AUX', 'OK' in this order. General reset with number 7038. Depress and hold the button 'P-' on the RC while switching on with the mains button. (Additionally on replacement of the memory, the Hotel Mode and the band limits are to be deactivated and the AGC and AFC are to be readjusted).
Grundig Grundig
CUC2030 CUC2030
CTV CTV
OSD position Service Mode Band Limits Cancelling Child Lock Cancel
Grundig
CUC2031
CTV
Grundig
CUC2031
CTV
Grundig
CUC2031
CTV
Default Values Entering
Manufacturer
Model
Chassis
Product
Mode
Enter
Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Depress and hold button 'i' on the RC while switching on with the mains button. Move the bar to 'AGC' in the Service Menu and operate the buttons 'AUX', 'OK' in this order. General reset with number 7038. Depress and hold the button 'P-' on the RC while switching on with the mains button. (Additionally on replacement of the memory, the Hotel Mode and the band limits are to be deactivated and the AGC and AFC are to be readjusted).
Grundig
CUC2031
CTV
Hotel Mode
Grundig Grundig
CUC2031 CUC2031
CTV CTV
OSD position Service Mode Band Limits Cancelling Child Lock Cancel
Grundig
CUC2050
CTV
Grundig
CUC2050
CTV
Grundig
CUC2050
CTV
Default Values Entering
Grundig
CUC2050
CTV
Hotel Mode
Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Depress and hold button 'i' on the RC while switching on with the mains button. Move the bar to 'AGC' in the Service Menu and operate the buttons 'AUX', 'OK' in this order. General reset with number 7038. Depress and hold the button 'P-' on the RC while switching on with the mains button. (Additionally on replacement of the memory, the Hotel Mode and the band limits are to be deactivated and the AGC and AFC are to be readjusted).
Grundig Grundig
CUC2050 CUC2050
CTV CTV
OSD position Service Mode Band Limits Cancelling Child Lock Cancel
Grundig
CUC2051
CTV
Grundig
CUC2051
CTV
Grundig
CUC2051
CTV
Default Values Entering
Grundig
CUC2051
CTV
Hotel Mode
Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'.
Manufacturer
Grundig Grundig Grundig
Model
Chassis
CUC2051 CUC2051 CUC6300
Product
CTV CTV CTV
Mode
OSD position Service Mode Child Lock Cancel Default Values Entering
Enter
Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Menu guide: 'i', 'Dialog Center', 'Service', 'Only for retailer', 'Code 8500'. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the 'i' button on the RC while switching on with the mains button. Menu guide: 'Horizontal Position', 'OK', 'OK', press 'i' to leave the menu. Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the 'i' button on the RC while switching on with the mains button. Menu guide: 'Horizontal Position', 'OK', 'OK', press 'i' to leave the menu. Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the 'i' button on the RC while switching on with the mains button. Menu guide: 'Horizontal Position', 'OK', 'OK', press 'i' to leave the menu. Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'.
Grundig
CUC6300
CTV
Grundig
CUC6300
CTV
Hotel Mode
Grundig Grundig
CUC6300 CUC6301
CTV CTV
OSD position Child Lock Cancel Default Values Entering
Grundig
CUC6301
CTV
Grundig
CUC6301
CTV
Hotel Mode
Grundig Grundig
CUC6301 CUC6310
CTV CTV
OSD position Child Lock Cancel Default Values Entering
Grundig
CUC6310
CTV
Grundig
CUC6310
CTV
Hotel Mode
Grundig
CUC6310
CTV
OSD position
Manufacturer
Model
Chassis
Product
Mode
Enter
Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'.
Grundig
CUC6330
CTV
Hotel Mode
Grundig
CUC6331
CTV
Hotel Mode
Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the button 'P-' on the RC while switching on with the mains button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Depress and hold button 'P/C' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'P/C' button on the RC while switching on with the mains button. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the button 'P-' on the RC while switching on with the mains button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Depress and hold button 'P/C' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'P/C' button on the RC while switching on with the mains button. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button.
Grundig
CUC6360
CTV
Child Lock Cancel Default Values Entering
Grundig
CUC6360
CTV
Grundig
CUC6360
CTV
EPROM Version Nr.
Grundig
CUC6360
CTV
Hotel Mode
Grundig Grundig Grundig
CUC6360 CUC6360 CUC6365
CTV CTV CTV
Service Mode Volume Offset Cancel Child Lock Cancel Default Values Entering
Grundig
CUC6365
CTV
Grundig
CUC6365
CTV
EPROM Version Nr.
Grundig
CUC6365
CTV
Hotel Mode
Grundig Grundig
CUC6365 CUC6365
CTV CTV
Service Mode Volume Offset Cancel
Manufacturer
Grundig
Model
Chassis
CUC6380
Product
CTV
Mode
Child Lock Cancel Default Values Entering
Enter
Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the button 'P-' on the RC while switching on with the mains button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Depress and hold button 'P/C' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'P/C' button on the RC while switching on with the mains button. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the button 'P-' on the RC while switching on with the mains button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Depress and hold button 'P/C' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'P/C' button on the RC while switching on with the mains button. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the button 'P-' on the RC while switching on with the mains button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version.
Grundig
CUC6380
CTV
Grundig
CUC6380
CTV
EPROM Version Nr.
Grundig
CUC6380
CTV
Hotel Mode
Grundig Grundig Grundig
CUC6380 CUC6380 CUC6450
CTV CTV CTV
Service Mode Volume Offset Cancel Child Lock Cancel Default Values Entering
Grundig
CUC6450
CTV
Grundig
CUC6450
CTV
EPROM Version Nr.
Grundig
CUC6450
CTV
Hotel Mode
Grundig Grundig Grundig
CUC6450 CUC6450 CUC6460
CTV CTV CTV
Service Mode Volume Offset Cancel Child Lock Cancel Default Values Entering
Grundig
CUC6460
CTV
Grundig
CUC6460
CTV
EPROM Version Nr.
Manufacturer
Model
Chassis
Product
Mode
Enter
Depress and hold button 'P/C' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'P/C' button on the RC while switching on with the mains button. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. Press VOL+, VOL-, PR-, PR+, OK. Depress and hold the button 'P-' on the RC while switching on with the mains button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Depress and hold button 'P/C' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'P/C' button on the RC while switching on with the mains button. Press and hold the 'AUX' button on the RC while switching the TV on with the mains button. Depress and hold down button 'P-' on the RC and switch the TV on from Standby with the local 'P+' button. (This is only possible once on replacement of the NVM or uP). Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Depress and hold button 'P/C' while switching on from Standby with button 'P+' on the TV. Set the Hotel Mode to 'OFF' with 'OK'. Depress and hold the 'AUX' button on the RC while switching the TV on from Standby with the local 'P+' button. Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold down button 'P-' on the RC and switch the TV on from Standby with the local 'P+' button. (This is only possible once on replacement of the NVM or uP).
Grundig
CUC6460
CTV
Hotel Mode
Grundig Grundig Grundig
CUC6460 CUC6460 CUC6469
CTV CTV CTV
Service Mode Volume Offset Cancel Child Lock Cancel Default Values Entering
Grundig
CUC6469
CTV
Grundig
CUC6469
CTV
EPROM Version Nr.
Grundig
CUC6469
CTV
Hotel Mode
Grundig Grundig
CUC6469 CUC6469
CTV CTV
Service Mode Volume Offset Cancel Default Values Entering EPROM Version Nr.
Grundig
CUC7300
CTV
Grundig
CUC7300
CTV
Grundig
CUC7300
CTV
Hotel Mode Volume Offset Cancel
Grundig
CUC7300
CTV
Grundig
CUC7301
CTV
Hotel Mode
Grundig
CUC7302
CTV
Default Values Entering
Manufacturer
Grundig
Model
Chassis
CUC7302
Product
CTV
Mode
EPROM Version Nr.
Enter
Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Depress and hold button 'P/C' while switching on from Standby with button 'P+' on the TV. Set the Hotel Mode to 'OFF' with 'OK'. Depress and hold the 'AUX' button on the RC while switching the TV on from Standby with the local 'P+' button. Depress and hold button 'i' on the RC while switching on with the mains button. Move the bar to 'AGC' in the Service Menu and operate the buttons 'AUX', 'OK' in this order. Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Depress and hold button 'i' on the RC while switching on with the mains button. Move the bar to 'AGC' in the Service Menu and operate the buttons 'AUX', 'OK' in this order. Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Depress and hold the 'i' button on the RC while switching on with the mains button. Set the OSD position in the menu and store with 'OK'. Depress and hold button 'i' on the RC while switching on with the mains button. In the menu line 'HOTEL' select 'ON' and leave the menu with button 'i'. Cancelling the Hotel Mode: Repeat the steps above but change 'HOTEL' to 'OFF'. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Press VOL+, VOL-, PR-, PR+, OK.
Grundig
CUC7302
CTV
Hotel Mode Volume Offset Cancel Band Limits Cancelling
Grundig
CUC7302
CTV
Grundig
CUC7303
CTV
Grundig
CUC7303
CTV
Hotel Mode
Grundig
CUC7303
CTV
OSD position Band Limits Cancelling
Grundig
CUC7305
CTV
Grundig
CUC7305
CTV
Hotel Mode
Grundig
CUC7305
CTV
OSD position
Grundig
CUC7350
CTV
Hotel Mode
Grundig
CUC7851
CTV
Child Lock Cancel EPROM Version Nr. Child Lock Cancel EPROM Version Nr. Child Lock Cancel
Grundig
CUC7851
CTV
Grundig
CUC7880
CTV
Grundig
CUC7880
CTV
Grundig
CUC7890
CTV
Manufacturer
Grundig
Model
Chassis
CUC7890
Product
CTV
Mode
EPROM Version Nr. Child Lock Cancel EPROM Version Nr.
Enter
Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Press VOL+, VOL-, PR-, PR+, OK. Press button 'i' to call up the 'Dialog Center' --> OK. The version number is shown by pressing the 'AUX' button. The index 01 of the part nr. (19798-300.01) indicates the EPROM version. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the STOP button. Press the 'STANDBY' button on the remote control handset until 'FREE' is indicated on the display of the video recorder. Press the 'STAND-BY' button on the RC until 'FREE' appears on the display of the recorder. Enter the numbers 4 9 3 4 on the remote control handset in this order and confirm with the button 'OK'. Press the STOP button. With the video recorder switched off (Stand-by) press the Stop button on the RC until 'UNLO' appears on the display of the recorder. With the video recorder switched off (Stand-by) press the Stop button on the RC until 'UNLO' appears on the display of the recorder. With the video recorder switched off (Stand-by) press the Stop button on the RC until 'FREE' appears on the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. With the video recorder switched off (Stand-by) press the Stop button on the RC until 'UNLO' appears on the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. With the video recorder switched off (Stand-by) press the Stop button on the RC until 'UNLO' appears on the display of the recorder.
Grundig
CUC7951
CTV
Grundig
CUC7951
CTV
Grundig
GV200 to GV250
VCR
Electronic Lock Cancel
Grundig Grundig
GV201-1 GV25SV/5 GV45SV/5 GV280PC GV280S GV400 GV400GB GV400OST GV4000VPS GV4001 GV4003VPS
VCR VCR
Electronic Lock Cancel Electronic Lock Cancel Electronic Lock Cancel Electronic Lock Cancel Electronic Lock Cancel Electronic Lock Cancel
Grundig
VCR
Grundig
VCR
Grundig
VCR
Grundig
VCR
Grundig
GV400VPS GV401VPT
VCR
Electronic Lock Cancel
Grundig
GV4010SV-VPT GV4092.. GV4192VPS GV4200SV-VPT GV4400HiFi GV4592.. GV402
VCR
Electronic Lock Cancel
Grundig
VCR
Electronic Lock Cancel
Grundig
GV404SV GV405EURO GV406EURO
VCR
Electronic Lock Cancel
Grundig
GV410
VCR
Electronic Lock Cancel
Manufacturer
Model
Chassis
Product
Mode
Enter
Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press and hold the 'STAND-BY' button on the RC (ca. 5s), until 'UNLOCKED' appears on the display of the recorder. With the video recorder switched off (Stand-by) press the Stop button on the RC until 'UNLO' appears on the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. With the video recorder switched off (Stand-by) press the Stop button on the RC until 'UNLO' appears on the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'STAND-BY' button on the RC until 'FREE' appears on the display of the recorder.
Grundig
GV410VPS GV411
VCR
Electronic Lock Cancel
Grundig
GV411-1 GV411OST GV412
VCR
Electronic Lock Cancel Electronic Lock Cancel
Grundig
VCR
Grundig
GV414SV GV415EURO GV416EURO GV420VPT
VCR
Electronic Lock Cancel
Grundig
GV430 GV430GB
VCR
Electronic Lock Cancel
Grundig
GV430VPS GV434SV GV435EURO
VCR
Electronic Lock Cancel
Grundig
GV440.. GV450.. GV460.. GV464.. GV465EURO GV470..
VCR
Electronic Lock Cancel
Grundig
GV500.. GV501VPT GV505EURO GV506EURO GV5000 GV5000GB GV5000VPS GV5000VPS/5 GV5002VPS GV5003 GV5008 GV5050 GV5050SV GV5050SV/1 GV5055EURO GV5095..
VCR
Electronic Lock Cancel
Grundig
VCR
Electronic Lock Cancel
Grundig
VCR
Electronic Lock Cancel
Press the 'STAND-BY' button on the RC until 'FREE' appears on the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains.
Grundig
VCR
Electronic Lock Cancel
Manufacturer
Model
GV510SV GV511 GV515EURO GV530.. GV535EURO GV540.. GV545EURO GV560.. GV565EURO GV5300..
Chassis
Product
Mode
Enter
Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'STAND-BY' button on the RC until 'FREE' appears on the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains.
Grundig
VCR
Electronic Lock Cancel
Grundig
VCR
Electronic Lock Cancel
Grundig
GV5395.. GV5400.. GV5695HiFi
VCR
Electronic Lock Cancel
Grundig
GV600 GV630 GV640HiFi GV640NIC GV645EURO GV650HiFi GV660HiFi GV660NIC GV665EURO GV670SHiFi GV670SNIC GV690SHiFi GV690SNIC GV6096SV GV6096SV/1 GV6396SV GV6596HiFi GV6596NIC
VCR
Electronic Lock Cancel
Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains.
Grundig
VCR
Electronic Lock Cancel
Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press and hold down the buttons 'STAND-BY' and 'SELECT' simultaneously on the RC until key simbol disappears from the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press and hold down the buttons 'STAND-BY' and 'SELECT' simultaneously on the RC until key simbol disappears from the display of the recorder.
Grundig
GV740.. GV745EURO
VCR
Electronic Lock Cancel
Grundig
GV7400..
VCR
Electronic Lock Cancel
Grundig
GV7497NIC
VCR
Electronic Lock Cancel
Grundig
GV8.. KV8.. SE8..
VCR
Electronic Lock Cancel
Manufacturer
Grundig Grundig Grundig
Model
GVP600ICNEURO KV5001VPS/5 KV5301VPS/5 MV4005 MV4105
Chassis
Product
VCR VCR VCR
Mode
Electronic Lock Cancel Electronic Lock Cancel Electronic Lock Cancel
Enter
Press the 'STAND-BY' button on the RC until 'FREE' appears on the display of the recorder. Press the 'STAND-BY' button on the RC until 'FREE' appears on the display of the recorder. With the video recorder switched off (Stand-by) press the Stop button on the RC until 'UNLO' appears on the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press and hold down the buttons 'STAND-BY' and 'SELECT' simultaneously on the RC until key simbol disappears from the display of the recorder. Press the 'CODE' button on the remote control handset. Enter the numers 4 9 3 4 on the remote control handset in this order and confirm with the 'OK' button. Press the 'STAND-BY' button or disconnect the recorder from the mains. Press and hold STOP button on the RC and depress the PLAY button on the video recorder. Press the 'STAND-BY' button or disconnect the video recorder from the mains. Press the cursor buttons on the RC in this order: VOL+, VOL-, PR+, PR-. Interconnect the service test points on the keyboard control unit for a short period. Switch the unit off and disconnect it from mains.
Grundig
SE4100VPS SE4104SV SE4120SV
VCR
Electronic Lock Cancel
Grundig
SE5102SV SE5104SV SE5106HiFi
VCR
Electronic Lock Cancel
Grundig
SE6102SV SE6104SV SE6106HiFi
VCR
Electronic Lock Cancel
Grundig
SE7104SV
VCR
Electronic Lock Cancel
Grundig
SE7105
VCR
Electronic Lock Cancel
Grundig
SE7106HiFi
VCR
Electronic Lock Cancel
Grundig
TVR3700 TVR3701 TVR3705 TVR3710 TVR3720 TVR3730 TVR4500 TVR4510
VCR
Electronic Lock Cancel
Grundig
VCR
Electronic Lock Cancel
Grundig
VCR
Electronic Lock Cancel
Manufacturer
Grundig
Model
TVR5100 TVR5130 TVR5500 TVR5510
Chassis
Product
VCR
Mode
Electronic Lock Cancel Electronic Lock Cancel Electronic Lock Cancel
Enter
Press the cursor buttons on the RC in this order: VOL+, VOL-, PR+, PR-. Interconnect the service test points on the keyboard control unit for a short period. Switch the unit off and disconnect it from mains. Press the cursor buttons on the RC in this order: VOL+, VOL-, PR+, PR-. Switch the video recorder off. Remove the top of the cabinet. Unplug the B1 connector on the sequence control. Switch the recorder on. After approx. 2 seconds, re-insert the B1 connector. Switch the video recorder off. Re-fit the top of the cabinet. Switch the video recorder off. Remove the top of the cabinet. Switch the recorder on. Interconnect the service test points on the keyboard control unit for a short period. Press the STOP button. Switch the video recorder off. Re-fit the top of cabinet. Enter the numbers 4 9 3 4 on the remote control handset in this order and confirm with the button '0000'. Press the STOP button. Enter the numbers 4 9 3 4 on the remote control handset in this order and confirm with the button 'OK'. Press the STOP button. Switch the video recorder off. Remove the top of the cabinet. Switch the recorder on. Interconnect the service test points on the keyboard control unit for a short period. Press the STOP button. Switch the video recorder off. Re-fit the top of cabinet. Enter the numbers 4 9 3 4 on the remote control handset in this order and confirm with the button 'OK'. Press the STOP button. MUTE --> OK (M) --> TV Controls: cursor buttons. Store: OK (M). Exit: TV Simultaneous press OK on RC & local panel. Simultaneous press OK on RC & local panel. Simultaneous press CM on the RC & "Service" key on the control panel. Select: MEM IN/OUT. Adjust: VOL +/-. Store: X. Exit: TV. Simultaneous press VT on the RC & "Service" key on the control panel. Select: MEM IN/OUT. Adjust: VOL +/-. Store: X. Exit: TV.
Grundig
VCR
Grundig
TVR5530
VCR
Grundig
VS200 to VS267
VCR
Electronic Lock Cancel
Grundig
VS300 to VS460
VCR
Electronic Lock Cancel
Grundig
VS500
VCR
Electronic Lock Cancel
Grundig
VS505 to VS510
VCR
Electronic Lock Cancel
Grundig
VS520 to VS550
VCR
Electronic Lock Cancel
Grundig
VS600 to VS960
VCR
Electronic Lock Cancel
ITT LG LG Loewe. MC64 MC84 Art.-Nr. 64420 66426 66449 66450 66460 66480 66490 Art.-Nr. 64420 66426 66449 66450 66460 66480 66490
STEREO PLUS
CTV CTV CTV
Service Mode Service Mode Service Mode TV Service Mode
C9000
CTV
Loewe.
C9000
CTV
VT Service Mode
Loewe.
C9003
CTV
On the local control press function key five times (indication "Service" will appear), afterwards Service Mode within a sec. press key "MEN" on the remote control. Store: X. Exit: TV. Service Mode Go to 'SERVICE' in menu and then quick press 'MENU' on the RC. Select: yellow cursors. Adjust: +/-. Store: 'X'. Exit: 'TV'.
Loewe.
Q2200
CTV
Manufacturer
Luxor Mitsubishi
Model
5585-21A1 7057-27 63/7954 CT21M5E XExx XPxx XVxx 6364, 7364
Chassis
STEREO PLUS
Product
CTV CTV
Mode
Service Mode Service Mode
Enter
MUTE --> OK (M) --> TV Controls: cursor buttons. Store: OK (M). Exit: TV Press S701 (on board) and button 9 (in 5s). Store: '0'. Exit: stand-by. Select DISPLAY MODE. Press PROCEED. Press and hold RESET. Then simultaneous press + & -. 'Warning Entering Service Menu...' appears. Press PROCEED for enter. Be careful! You can damage a monitor! Quick press: --\-, MENU, TV. In 1s press buttons '-/--', 'MENU', 'TV'. Select: PR+/-. Adjust: VOL+/-. Store: fill-dot-symbol on RC (near 'i' button). Exit: 'STANDBY'. MUTE --> OK (M) --> TV Controls: cursor buttons. Store: OK (M). Exit: TV i --> M --> PROGR. Controls: cursor buttons. Store: M. Exit: TV Switch to Standby. Switch off with the mains switch. Press and hold red button on RC and then switch on with the mains switch (cca 10s). Select: numbers buttons. Adjust: +/-. Store: red button. Exit: 'MUTE'. Switch to Standby. Switch off with the mains switch. Press and hold red button on RC and then switch on with the mains switch (cca 10s). Select: numbers buttons. Adjust: +/-. Store: red button. Exit: 'MUTE'. After replacement of the MDA2061 (IR73) the TV receiver acts as folows: a) All programme storages have stored Ch00. b) The indicator shows German function characters. c) PAL and SECAM EAST standard recepcion is possible (not NTSC and/or SECAM WEST). If required to change according to paragr. b and c then switch off the set by the mains switch. Press both buttons + and - for volume on TV and simultaneously switch the set on with the mains switch. Keep the two volume buttons pressed until the display indicates Pr. After 8s the display indicates __. Now the following buttons can be presseed on the RC, thus additional corresponding segments will be illuminated: Button '1' function symbols indicate international display. Reversible to German display with button '2'. Button '5' additional SECAM WEST and/or NTSC reception (Multistandard). Reversible to Single Standard with button '3'. Store: Stand-By. Switch to Stand By. Switch off with the mains switch. Press and hold 'VT' on RC then switch on with the mains switch.
NEC
MON
Service Mode
Nokia Nokia
2B-F EUROSTEREO
CTV CTV
Service Mode Service Mode
Nokia
63/7168 55A1-0 45H1-0 55Y2-0 63/7157 63/7177
STEREO PLUS
CTV
Service Mode
Nokia
STEREO PLUS
CTV
Service Mode
Nordmende
DC1
CTV
Service Mode
Nordmende
DC2
CTV
Service Mode
Nordmende
Color 3038
F15-03 110°
CTV
MDA2061 Replacement
Nordmende
ICC10
CTV
Service Mode
Manufacturer
Model
Chassis
Product
Mode
Enter
Nordmende
ICC9
CTV
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED switch off. Simultaneous press blue button on Service Mode RC and switch on TV with main switch. Press blue button again. (WARNING: scart must be free.) Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneously press P- & P+ on local keyboard. Commands: arrows. Store: OK. Exit: TV. In Sound-Menu Low-tone-regel to MAX and High-tone-regel to MIN. Press VOL- on TV and RESET on RC in some time. Select: red and green buttons. Adjust: yellow and blue buttons. Store: 'STORE'. Exit: switch off. In Sound-Menu Low-tone-regel to MAX and High-tone-regel to MIN. Press 'F' button on TV. Then press VOL- on TV and REVEAL on RC in some time. Select: red and green buttons. Adjust: yellow and blue buttons. Store: 'STR'. Exit: 'N' on RC. ON: Press simultaneously 'OFF TIMER' on RC and 'CH.UP' local. OFF: Press simultaneously 'OFF TIMER' on RC and 'VOL-' local. Simultaneously press 'RECALL' on RC and 'VOL-' local. Exit: 'NORMAL' on RC. ON: Set HOTEL ON in Service Menu. Select programm 38. Simultaneous press (3 sec) INSTALL & P- on local keyboard. OFF: Set HOTEL OFF in Service Menu. Simultaneously press VOL+ & P- on RC. Exit: STANDBY. OFF: Select programm 38. Simultaneous press (3 sec) PR+ & VOL- on local keyboard. ON: Select programm 38. Simultaneous press (3 sec) STORE & PR- on local keyboard. With special service RC. Or short M25, M25 on board and then switch on TV. Exit: st-by. Select program 38 on the TV. Simultaneously press the keys VOLUME- and VOLUME+ on the keyboard of the TV and the OSD key of the remote control. This model also supports the 062596 sequence followed by [MENU] (service default) or [i+]/[OSD] (service mode). There is a small Service jumper to short on the small signal PCB. When the TV is in this first level service mode, you can go in the second level service mode by pressing both MENU and - keys on top of the TV at the same time. There you can read much parameters and proceed with most of the adjustments. In fact this method let you use an ordinary Remote control but you also need to open the back cover. With the special service remote control, a special code is sent to enter the service mode.
Palladium
TV-100
CTV
Service Mode
Panasonic
EURO-1
CTV
Service Mode
Panasonic
EURO-2
CTV
Service Mode
Panasonic
MX-3 MX-3C MX-3 MX-3C ANUBIS B
CTV
Hotel Mode
Panasonic
CTV
Service Mode
Philips
CTV
Hotel Mode
Philips
ANUBIS B
CTV
Service Mode
Philips
Anubis S
CTV
Hotel Mode
Philips
L7.1A
CTV
Service Mode
Philips
L9.1
CTV
Hotel Mode
Philips
L9H
CTV
Service Mode
Philips
MD1.2E
CTV
Service Mode
Manufacturer
Model
Chassis
Product
Mode
Enter
Philips
MG3.1E
CTV
Option 1: In the TV-set itself is a 3-pin connector with which either SERVICE-DEFAULT or SERVICE-MODE can be activated. This connector is depicted 0356 (SERVICE-PINS) on page K7 (TXT&CONTROL). Shorting pins 1-2 will activate SERVICE-MODE. Shorting pins 2-3 will activate SERVICE-DEFAULT. Option 2: Activate these modes using the remote control. Obviously option 2 is the preferred method because the settings have to be changed using a remote control anyway.... To activate SERVICE-DEFAULT: Press 0 6 2 5 9 6 and then the [menu] button. The message `Service Default' Service Mode appears and channel `SER T' will be selected. This only sets some settings to a preset value (color/brightness/volume and such). This mode is primarily intended to be used when the non volatile memory has been replaced. It is then loaded with the default values. To activate SERVICE-MODE: Press 0 6 2 5 9 6 and then the [i+] button. After pressing 0 6 2 5 9 6 the message `Dealer' should have appeared. Do not worry about the channel changing while you press the numbers. Service technicians have the m service mode using a special re Use the standard remote control an key in a special sequence 0 6 2 5 9 6 followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press 'MENU' again to clear it. The other way is to Service Mode short the two service pins on the signal panel (pins 2 and 3 of connector 0356). The advantage of this last method is that all the software protections are turned off. Use the standard remote control an key in a special sequence 0 6 2 5 9 6 followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press 'MENU' again to clear it. Without cassette. Press and hold SYSTEM till 'G591' appears. Press and hold CLEAR(CL) till 'MOFF' appears. Exit: TV/STANBY. Without cassette. Press and hold SYSTEM till 'MOFF' appears. Press and hold CLEAR(CL) till 'G591' appears. Exit: TV/STANBY. Press CHILD LOCK (key-simbol) on the RC for 5s with the VCR switched on. Without cassette. Press and hold STOP on the RC and then press STOP/EJECT on VCR. Select the line 'MODULATOR' on the TV screen or 'MOD+' in the display with P+/-. In the display select 'OFF' / 'MOD-' (modulator off) with VOLor 'MOD+' (modulator on). Confirm with OK. Exit with MENU
Philips
29PT9416
MG7.1
CTV
Philips
Y6
CTV
Service Mode
Philips
VR210/58
VCR
Modulator off Modulator on Child Lock Cancel
Philips Philips
VR210/58 VR220/58
VCR VCR
Philips
VR220/58
VCR
Modulator on/off
Manufacturer
Model
Chassis
Product
Mode
Enter
Without cassette. Hold the STOP button on the RC. In addition press the STOP/EJECT button on the VCR until the pre-set modulator frequency appears in the display, e.g. 'M591' (591MHz or 36 ch. UHF). Select line 'OPTIMIZE FREQUENCY' using P+/-. Enter new modulator frequency with the numbers 0-9. In line 'SOUND SYSTEM' select the TV system using VOL+/-. 'G' = PAL B/G. 'K' = SECAM D/K. Confirm with OK. 'STORED' will appear briefly on the screen. Disconect from the mains power supply. Press and hold the STANDBY/ON button on the device and reconnect to the mains power supply. Release the button when 'OSD' appears in the VCR display. Press and hold STOP till [] appears. Without cassette. Press and hold SYSTEM till 'G591' appears. Press and hold CLEAR(CL) till 'MOFF' appears. Exit: TV/STANBY. Without cassette. Press and hold SYSTEM till 'MOFF' appears. Press and hold CLEAR(CL) till 'G591' appears. Exit: TV/STANBY. Without cassette. VCR st-by. Press and hold SYSTEM till 'G591' appears. System change: SELECT. Freq. Change: P +/-. Store: OK. Exit: TV/STANBY.
Philips
VR220/58
VCR
Modulator preset
Philips
VR220/58
VCR
Reset to factory settings Auto ST-BY off Modulator off Modulator on Modulator preset
Philips Philips
VR400/58 VR400/58
VCR VCR
Philips
VR400/58
VCR
Philips
VR400/58
VCR
Revox
D-TV
C9003
CTV
On the local control press function key five times (indication "Service" will appear), afterwards Service Mode within a sec. press key "MEN" on the remote control. Store: X. Exit: TV. Switch off set with main switch. Switch on set with main switch and during doing this press the buttons + and - of volume control on the set's control bord simultaneously until the display lights. Display: SS... Press the button 'S' on the RC. Switch off with RC. Now the combination lock is unlocked and one can switch on again in the normal manner.
Saba
ULTRACOLOR T55U42 T55U43 T63U42 T63U43
ICC5115ML 110 ICC5116MM 90°
CTV
Combination Lock Cancel
Saba
ICC9
CTV
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED Service Mode switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again. (WARNING: scart must be free.) Put TV into standby, then turn power off, then turn power on whilst holding standby button on remote and step through menus to `vol set` and increase level to max. Quick press: --\-, MENU, TV. MUTE --> OK (M) --> TV Controls: cursor buttons. Store: OK (M). Exit: TV
Saba Salora Salora
T7032VT 28N8S 17/21SF 25/28X71 25/28SP50
TX92 2B-F STEREO PLUS
CTV CTV CTV
Hotel Mode Cancel Service Mode Service Mode
Manufacturer
Model
CB-14F1 CB-20P30 CB-20H1 CB-20S20 CB-21H1 CB-21P30 CB-21S20 CB-3373 CB-5020 CB-5073 CB-5079 CB-5320 CB-5373 CB-5379
Chassis
Product
Mode
Enter
Samsung
S15A
CTV
Service Mode
STAND-BY --> DISPLAY --> P.STD --> MUTE --> POWER ON. Controls: VOL +/-, CH +/-. Exit: POWER OFF.
Samsung
CK5038
SCT11B
CTV
Service Mode
Samsung
CX5944 CX6844 CB-14V10 CB-3373 CB-14V20 CB-5073 CB-20P30 CB-5079 CB-20S10 CB-5373 CB-20S20 CB-21P30 CB-21S10 CB-21S20 CS7272 CS-721 CS-723 TVP3350 TVP5050
SCT12B
CTV
Service Mode
STAND-BY --> P.STD --> HELP --> SLEEP --> POWER ON. Controls: VOL +/-, CH +/-. Exit: STATUS. STAND-BY --> P.STD --> HELP --> SLEEP --> POWER ON. FACTORY MODE: set PSL=15 and PVA=63. Controls: VOL +/-, CH +/-. Exit: STATUS
Samsung
SCT13B
CTV
Service Mode
STAND-BY --> P.STD --> HELP --> SLEEP --> POWER ON. Controls: VOL +/-, CH +/-. Exit: STATUS.
Samsung Samsung Samsung Schneider
SCT51A SCT52A SCV11A SCV11B DTV 1
CTV CTV
Service Mode Service Mode
CTV/VCR Service Mode CTV Service Mode
Schneider
DTV 100
CTV
Service Mode
PICTURE OFF --> SLEEP --> P.STD --> MUTE --> PICTURE ON PICTURE OFF --> SLEEP --> P.STD --> MUTE --> PICTURE ON STAND-BY --> P.STD --> MENU --> SLEEP --> POWER ON Simultaneous press Service-button on digibord & button C on RC. Selection: Bass +/-. Adjust: Volume +/-. Store: T. Exit: TV. Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneous press P- & P+ on local keyboard. Commands: arrows. Store: OK. Exit: TV.
Schneider
DTV 2
CTV
Like DTV 1 or simultaneous press Servicebutton (down right on RC) & C button on RC. Service Mode Selection: Bass +/-. Adjust: Volume +/-. Store: IDEAL. Exit: TV. Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneous press P- & VOL+ on local keyboard. Selection: wheel. Adjust: ring. Store: red button. Exit: OFF. Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneous press P- & VOL+ on local keyboa