Text preview for : 4526.pdf part of ON SEMICONDUCTOR 4526 Presettable 4-Bit Down Counters



Back to : 4526.pdf | Home

MC14526B Presettable 4-Bit Down Counters
The MC14526B binary counter is constructed with MOS P­channel and N­channel enhancement mode devices in a monolithic structure. This device is presettable, cascadable, synchronous down counter with a decoded "0" state output for divide­by­N applications. In single stage applications the "0" output is applied to the Preset Enable input. The Cascade Feedback input allows cascade divide­by­N operation with no additional gates required. The Inhibit input allows disabling of the pulse counting function. Inhibit may also be used as a negative edge clock. This complementary MOS counter can be used in frequency synthesizers, phase­locked loops, and other frequency division applications requiring low power dissipation and/or high noise immunity.
http://onsemi.com MARKING DIAGRAMS
16 PDIP­16 P SUFFIX CASE 648 MC14526BCP AWLYYWW 1 16 SOIC­16 DW SUFFIX CASE 751G 1 16 SOEIAJ­16 F SUFFIX CASE 966 MC14526B ALYW 1 Unit V V mA mW °C °C °C A WL, L YY, Y WW, W = Assembly Location = Wafer Lot = Year = Work Week 14526B

· Supply Voltage Range = 3.0 Vdc to 18 Vdc · Logic Edge­Clocked Design -- Incremented on Positive Transition · Asynchronous Preset Enable · Capable of Driving Two Low­power TTL Loads or One Low­power
Schottky TTL Load Over the Rated Temperature Range of Clock or Negative Transition of Inhibit

AWLYYWW

MAXIMUM RATINGS (Voltages Referenced to VSS) (Note 2.)
Symbol VDD Vin, Vout Iin, Iout PD TA Tstg TL Parameter DC Supply Voltage Range Input or Output Voltage Range (DC or Transient) Input or Output Current (DC or Transient) per Pin Power Dissipation, per Package (Note 3.) Operating Temperature Range Storage Temperature Range Lead Temperature (8­Second Soldering) Value ­0.5 to +18.0 ­0.5 to VDD + 0.5 ±10 500 ­55 to +125 ­65 to +150 260

ORDERING INFORMATION
Device MC14526BCP MC14526BDW MC14526BDWR2 MC14526BF Package PDIP­16 SOIC­16 SOIC­16 SOEIAJ­16 Shipping 2000/Box 47/Rail 1000/Tape & Reel See Note 1.

2. Maximum Ratings are those values beyond which damage to the device may occur. 3. Temperature Derating: Plastic "P and D/DW" Packages: ­ 7.0 mW/_C From 65_C To 125_C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high­impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS v (Vin or Vout) v VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open.

1. For ordering information on the EIAJ version of the SOIC packages, please contact your local ON Semiconductor representative.

© Semiconductor Components Industries, LLC, 2000

1

August, 2000 ­ Rev. 4

Publication Order Number: MC14526B/D

MC14526B
PIN ASSIGNMENT
Q3 P3 PE INHIBIT P0 CLOCK VSS 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VDD Q2 P2 CF 0" P1 RESET Q1

FUNCTION TABLE
Inputs Clock X X X X L H H Reset H H H L L L L L L L Inhibit X X X X H L L Preset Enable L H X H L L L L L L Cascade Feedback L L H X X X L L L L Output "0" L H H L L L L L L L Resulting Function Asynchronous reset reset* Asynchronous reset y Asynchronous reset A h Asynchronous preset Decrement inhibited ec e e b ed Decrement inhibited No change** (inactive edge) change No change** (inactive edge) change Decrement Decrement** Decrement**

X = Don't Care NOTES: ** Output "0" is low when reset goes high only it PE and CF are low. ** Output "0" is high when reset is low, only if CF is high and count is 0000.

http://onsemi.com
2

MC14526B

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS)
VDD Vdc 5.0 10 15 5.0 10 15 5.0 10 15 VIH 5.0 10 15 IOH Source 5.0 5.0 10 15 IOL 5.0 10 15 15 -- 5.0 10 15 5.0 10 15 ­ 3.0 ­ 0.64 ­ 1.6 ­ 4.2 0.64 1.6 4.2 -- -- -- -- -- -- -- -- -- -- -- -- ± 0.1 -- 5.0 10 20 ­ 2.4 ­ 0.51 ­ 1.3 ­ 3.4 0.51 1.3 3.4 -- -- -- -- -- ­ 4.2 ­ 0.88 ­ 2.25 ­ 8.8 0.88 2.25 8.8 ±0.00001 5.0 0.005 0.010 0.015 -- -- -- -- -- -- -- ± 0.1 7.5 5.0 10 20 ­ 1.7 ­ 0.36 ­ 0.9 ­ 2.4 0.36 0.9 2.4 -- -- -- -- -- -- -- -- -- -- -- -- ± 1.0 -- 150 300 600 mAdc 3.5 7.0 11 -- -- -- 3.5 7.0 11 2.75 5.50 8.25 -- -- -- 3.5 7.0 11 -- -- -- mAdc Characteristic Symbol VOL Min -- -- -- ­ 55_C 25_C 125_C Max Min -- -- -- Typ (4.) 0 0 0 Max Min -- -- -- Max Unit Vdc Output Voltage Vin = VDD or 0 "0" Level 0.05 0.05 0.05 -- -- -- 1.5 3.0 4.0 0.05 0.05 0.05 -- -- -- 1.5 3.0 4.0 0.05 0.05 0.05 -- -- -- 1.5 3.0 4.0 Vdc "1" Level Vin = 0 or VDD Input Voltage "0" Level (VO = 4.5 or 0.5 Vdc) (VO = 9.0 or 1.0 Vdc) (VO = 13.5 or 1.5 Vdc) "1" Level (VO = 0.5 or 4.5 Vdc) (VO = 1.0 or 9.0 Vdc) (VO = 1.5 or 13.5 Vdc) Output Drive Current (VOH = 2.5 Vdc) (VOH = 4.6 Vdc) (VOH = 9.5 Vdc) (VOH = 13.5 Vdc) (VOL = 0.4 Vdc) (VOL = 0.5 Vdc) (VOL = 1.5 Vdc) Input Current Input Capacitance (Vin = 0) Quiescent Current (Per Package) Total Supply Current (5.) (6.) (Dynamic plus Quiescent, Per Package) (CL = 50 pF on all outputs, all buffers switching) VIL -- -- -- -- -- -- 2.25 4.50 6.75 -- -- -- VOH 4.95 9.95 14.95 4.95 9.95 14.95 5.0 10 15 4.95 9.95 14.95 Vdc Vdc Sink Iin Cin IDD µAdc pF µAdc IT IT = (1.7 µA/kHz) f + IDD IT = (3.4 µA/kHz) f + IDD IT = (5.1 µA/kHz) f + IDD µAdc 4. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. 5. The formulas given are for the typical characteristics only at 25_C. 6. To calculate total supply current at loads other than 50 pF: IT(CL) = IT(50 pF) + (CL ­ 50) Vfk where: IT is in µA (per package), CL in pF, V = (VDD ­ VSS) in volts, f in kHz is input frequency, and k = 0.001.

http://onsemi.com
3

MC14526B

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
SWITCHING CHARACTERISTICS (7.) (CL = 50 pF, TA = 25_C)
Characteristic Output Rise and Fall Time tTLH, tTHL = (1.5 ns/pF) CL + 25 ns tTLH, tTHL = (0.75 ns/pF) CL + 12.5 ns tTLH, tTHL = (0.55 ns/pF) CL + 9.5 ns Symbol VDD 5.0 10 15 Min -- -- -- Typ (8.) 100 50 40 Max 200 100 80 Unit ns tTLH, tTHL (Figures 4, 5) Propagation Delay Time (Inhibit Used as Negative Edge Clock) Clock or Inhibit to Q tPLH, tPHL = (1.7 ns/pF) CL + 465 ns tPLH, tPHL = (0.66 ns/pF) CL + 197 ns tPLH, tPHL = (0.5 ns/pF) CL + 135 ns Clock or Inhibit to "0" tPLH, tPHL = (1.7 ns/pF) CL + 155 ns tPLH, tPHL = (0.66 ns/pF) CL + 87 ns tPLH, tPHL = (0.5 ns/pF) CL + 65 ns Propagation Delay Time Pn to Q Propagation Delay Time Reset to Q Propagation Delay Time Preset Enable to "0" Clock or Inhibit Pulse Width tPLH, tPHL (Figures 4, 7) tPHL (Figure 8) tPHL, tPLH (Figures 4, 9) tw (Figures 5, 6) Clock Pulse Frequency (with PE = low) fmax (Figures 4, 5, 6) Clock or Inhibit Rise and Fall Time tr, tf (Figures 5, 6) tsu (Figure 10) Hold Time Preset Enable to Pn Preset Enable Pulse Width th (Figure 10) tw (Figure 10) Reset Pulse Width tw (Figure 8) Reset Removal Time trem (Figure 8) tPLH, tPHL (Figures 4, 5, 6) 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 5.0 10 15 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 250 100 80 -- -- -- -- -- -- 90 50 40 30 30 30 250 100 80 350 250 200 10 20 30 550 225 160 240 130 100 260 120 100 250 110 80 220 100 80 125 50 40 2.0 5.0 6.6 -- -- -- 40 15 10 ­ 15 ­5 0 125 50 40 175 125 100 ­ 110 ­ 30 ­ 20 1100 450 320 480 260 200 520 240 200 500 220 160 440 200 160 -- -- -- 1.5 3.0 4.0 15 5 4 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- ns ns ns ns ns MHz µs Setup Time Pn to Preset Enable ns ns ns ns ns 7. The formulas given are for the typical characteristics only at 25_C. 8. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance.

http://onsemi.com
4

MC14526B
VDD = -VGS CF PE P0 P1 P2 P3 RESET INHIBIT CLOCK Q0 Q1 Q2 Q3 0" EXTERNAL POWER SUPPLY IOH VOH VDD = VGS CF PE P0 P1 P2 P3 RESET INHIBIT CLOCK Q0 Q1 Q2 Q3 0" EXTERNAL POWER SUPPLY IOL VOL

VSS

VSS

Figure 1. Typical Output Source Characteristics Test Circuit

Figure 2. Typical Output Sink Characteristics Test Circuit

VDD CF PE P0 P1 P2 P3 RESET INHIBIT CLOCK Q0 Q1 Q2 Q3 0" VSS PULSE GENERATOR CL CL CL CL CL Q or 0" CL* TEST POINT

DEVICE UNDER TEST

20 ns CLOCK

50%

20 ns VDD 90% 10% VSS VARIABLE 50% DUTY CYCLE WIDTH

* Includes all probe and jig capacitance.

Figure 3. Power Dissipation

Figure 4. Test Circuit

http://onsemi.com
5

MC14526B
SWITCHING WAVEFORMS
tr CLOCK 90% 50% 10% tw 1/fmax tPLH ANY Q OR 0" 90% 50% 10% tTLH tTHL tPHL ANY Q OR 0" 90% 50% 10% tTLH tTHL tPLH tf VDD INHIBIT VSS tf 90% 50% 10% tw 1/fmax tPHL tr VDD VSS

Figure 5.

Figure 6.

tw VDD RESET tr ANY P 90% 50% 10% tPLH ANY Q 50% tPHL tf VDD VSS ANY Q 50% VSS tPHL 50%

trem CLOCK VDD 50% VSS

Figure 7.

Figure 8.

VALID tr PRESET ENABLE 90% 50% 10% tPHL 0" 50% tPLH tf VDD GND PRESET ENABLE tw ANY P 50% VSS tsu 50% VSS th VDD VDD

Figure 9.

Figure 10.

http://onsemi.com
6

MC14526B
PIN DESCRIPTIONS Preset Enable (Pin 3) -- If Reset is low, a high level on the Preset Enable input asynchronously loads the counter with the programmed values on P0, P1, P2, and P3. Inhibit (Pin 4) -- A high level on the Inhibit input pre­ vents the Clock from decrementing the counter. With Clock (pin 6) held high, Inhibit may be used as a negative edge clock input. Clock (Pin 6) -- The counter decrements by one for each rising edge of Clock. See the Function Table for level requirements on the other inputs. Reset (Pin 10) -- A high level on Reset asynchronously forces Q0, Q1, Q2, and Q3 low and, if Cascade Feedback is high, causes the "0" output to go high. "0" (Pin 12) -- The "0" (Zero) output issues a pulse one clock period wide when the counter reaches terminal count (Q0 = Q1 = Q2 = Q3 = low) if Cascade Feedback is high and Preset Enable is low. When presetting the counter to a value other than all zeroes, the "0" output is valid after the rising edge of Preset Enable (when Cascade Feedback is high). See the Function Table. Cascade Feedback (Pin 13) -- If the Cascade Feedback input is high, a high level is generated at the "0" output when the count is all zeroes. If Cascade Feedback is low, the "0" output depends on the Preset Enable input level. See the Function Table. P0, P1, P2, P3 (Pins 5, 11, 14, 2) -- These are the preset data inputs. P0 is the LSB. Q0, Q1, Q2, Q3 (Pins 7, 9, 15, 1) -- These are the synchronous counter outputs. Q0 is the LSB. VSS (Pin 8) -- The most negative power supply potential. This pin is usually ground. VDD (Pin 16) -- The most positive power supply potential. VDD may range from 3 to 18 V with respect to VSS.

STATE DIAGRAM
MC14526B
0 1 2 3 4

15

5

14

6

13

7

12

11

10

9

8

http://onsemi.com
7

MC14526B
MC14526B LOGIC DIAGRAM (Binary Down Counter)
P0 5 Q0 7 P1 11 Q1 9 P2 14 Q2 15 P3 2 Q3 1

D R C T PE Q VDD

D RQ C T PE Q VDD

D RQ C T PE Q

D RQ C T PE Q

CF PE INHIBIT

13 3 4 12 0"

CLOCK RESET

10

6

http://onsemi.com
8

MC14526B
APPLICATIONS INFORMATION
Divide­By­N, Single Stage Cascaded, Presettable Divide­By­N

Figure 11 shows a single stage divide­by­N application. To initialize counting a number, N is set on the parallel inputs (P0, P1, P2, and P3) and reset is taken high asynchronously. A zero is forced into the master and slave of each bit and, at the same time, the "0" output goes high. Because Preset Enable is tied to the "0" output, preset is enabled. Reset must be released while the Clock is high so the slaves of each bit may receive N before the Clock goes low. When the Clock goes low and Reset is low, the "0" output goes low (if P0 through P3 are unequal to zero). The counter downcounts with each rising edge of the Clock. When the counter reaches the zero state, an output pulse occurs on "0" which presets N. The propagation delays from the Clock's rising and falling edges to the "0" output's rising and falling edges are about equal, making the "0" output pulse approximately equal to that of the Clock pulse. The Inhibit pin may be used to stop pulse counting. When this pin is taken high, decrementing is inhibited.

Figure 12 shows a three stage cascade application. Taking Reset high loads N. Only the first stage's Reset pin (least significant counter) must be taken high to cause the preset for all stages, but all pins could be tied together, as shown. When the first stage's Reset pin goes high, the "0" output is latched in a high state. Reset must be released while Clock is high and time allowed for Preset Enable to load N into all stages before Clock goes low. When Preset Enable is high and Clock is low, time must be allowed for the zero digits to propagate a Cascade Feedback to the first non­zero stage. Worst case is from the most significant bit (M.S.B.) to the L.S.B., when the L.S.B. is equal to one (i.e. N = 1). After N is loaded, each stage counts down to zero with each rising edge of Clock. When any stage reaches zero and the leading stages (more significant bits) are zero, the "0" output goes high and feeds back to the preceding stage. When all stages are zero, the Preset Enable automatically loads N while the Clock is high and the cycle is renewed.

N VDD VSS

P0 P1 P2 P3 CF RESET INHIBIT CLOCK PE

Q0 Q1 Q2 Q3 0"

BUFFER

fin

N

fin

Figure 11. ÷ N Counter

LSB N0 N1 N2 N3 P0 P1 P2 P3 CLOCK INHIBIT RESET CF 0" PE VSS Q0 Q1 Q2 Q3

N4 N5 N6 N7 P0 P1 P2 P3 CLOCK INHIBIT RESET CF 0" PE VSS Q0 Q1 Q2 Q3

MSB N8 N9 N10 N11 P0 P1 P2 P3 CLOCK INHIBIT RESET Q0 Q1 Q2 Q3 CF 0" PE VDD

fin VSS VDD

LOAD N

10 K VSS

BUFFER fin N

Figure 12. 3 Stages Cascaded

http://onsemi.com
9

MC14526B
PACKAGE DIMENSIONS

­A­
16 9

PDIP­16 P SUFFIX PLASTIC DIP PACKAGE CASE 648­08 ISSUE R
B

1

8

NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01

F S

C

L

­T­ H G D
16 PL

SEATING PLANE

K

J T A
M

M

0.25 (0.010)

M

SOIC­16 DW SUFFIX PLASTIC SOIC PACKAGE CASE 751G­03 ISSUE B
D
16 M 9

A

q
NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INLCUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A A1 B C D E e H h L q MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 10.15 10.45 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0_ 7_

H

B

1 16X

8

B T A
S

B B
S

0.25

M

A

h X 45 _
SEATING PLANE

M

8X

0.25

E

A1

14X

e

T

C

http://onsemi.com
10

L

MC14526B
PACKAGE DIMENSIONS

SOEIAJ­16 F SUFFIX PLASTIC EIAJ SOIC PACKAGE CASE 966­01 ISSUE O
LE Q1 E HE
1 8

16

9

M_ L DETAIL P

Z D e A VIEW P

NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.031

c

b 0.13 (0.005)
M

A1 0.10 (0.004)

http://onsemi.com
11

MC14526B

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.

PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303­675­2175 or 800­344­3860 Toll Free USA/Canada Fax: 303­675­2176 or 800­344­3867 Toll Free USA/Canada Email: [email protected] Fax Response Line: 303­675­2167 or 800­344­3810 Toll Free USA/Canada N. American Technical Support: 800­282­9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor ­ European Support German Phone: (+1) 303­308­7140 (Mon­Fri 2:30pm to 7:00pm CET) Email: ONlit­[email protected] French Phone: (+1) 303­308­7141 (Mon­Fri 2:00pm to 7:00pm CET) Email: ONlit­[email protected] English Phone: (+1) 303­308­7142 (Mon­Fri 12:00pm to 5:00pm GMT) Email: [email protected] EUROPEAN TOLL­FREE ACCESS*: 00­800­4422­3781 *Available from Germany, France, Italy, UK CENTRAL/SOUTH AMERICA: Spanish Phone: 303­308­7143 (Mon­Fri 8:00am to 5:00pm MST) Email: ONlit­[email protected] ASIA/PACIFIC: LDC for ON Semiconductor ­ Asia Support Phone: 303­675­2121 (Tue­Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001­800­4422­3781 Email: ONlit­[email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4­32­1 Nishi­Gotanda, Shinagawa­ku, Tokyo, Japan 141­0031 Phone: 81­3­5740­2745 Email: [email protected] ON Semiconductor Website: http://onsemi.com

For additional information, please contact your local Sales Representative.

http://onsemi.com
12

MC14526B/D