Text preview for : 21HT15C.pdf part of SHARP 21HT-15C Service manual for PAL SECAM B/G, D/K SYSTEM COLOUR TELEVISION models: 21HT-15C , 21HT-16C
Back to : 21HT15C.part1.rar | Home
21HT-15C 21HT-16C
SERVICE MANUAL
SE0021HT1*C00
Issued: 14th Nov 2002
GA-1E CHASSIS PAL SECAM B/G, D/K SYSTEM COLOUR TELEVISION
MODELS
21HT-15CS 21HT-16CS
In the interests of user safety (required by safety regulations in some countries) the set should restored to its original condition and only parts identical to those specified should be used.
CONTENTS
ELECTRICAL SPECIFICATIONS ..................... 3 IMPORTANT SERVICING NOTES .................. 4 CONTROLS & TERMINALS ............................. 5 SERVICE ADJUSTMENTS .............................. 6 HOTEL MODE FUNCTIONS .......................... 12 CHASSIS LAYOUTS .......................................14 LED FLASHING CODE ...................................15 PRINTED WIRING BOARDS ........................... 15 ICs ADDITIONAL INFORMATION ..................20 SCHEMATIC DIAGRAMS .............................. 26 BLOCK DIAGRAMS ....................................... 32 TROUBLESHOOTING TABLES ...................... 35 PARTS LISTING .............................................. 38 CRT ADAPTATION ........................................ 42 SOURCE OF DOCUMENTATION ................. 43
SHARP CORPORATION This document has been published to
1
be used for after sales service only.
21HT-15C 21HT-16C
Service Manual update log sheet
Technical Report No. Technical Bulletin No. Cause / Solution Part No. Page No. Application Data /Serial No.
Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc. If only part number changes are required, just change part number directly the part number in the Parts Listing Section. If you need more information, please refer to the Technical Report (Bulletin).
2
21HT-15C 21HT-16C
ELECTRICAL SPECIFICATIONS
·Power Input .................... 220V-240 Volts AC 50Hz ·Power Consumption
·Sound Carrier Trap
B/G ................................................ 33.4MHz D/K ................................................ 32.4MHz B/G ................................................ 40.4MHz D/K ................................................ 40.4MHz B/G ............................................... 31.9MHz D/K ............................................... 30.9MHz VHF/UHF .................... 75 ohm Unbalanced VHF ......................... CH02-CH12, R01-R12 S1-S41 (HYPERBAND) UHF ....................................... CH21 - CH69
Normal Operation (Method IEC60107) ........ 43W Stand-by Operation .................................. 3W
·Adjacent Sound Carrier Trap
·Audio Power Output Rating .............. 4W x 1 (MPO) ·Speaker ............................ 16 4W, 9 x 5 cm, 1pc ·Convergence ................... Self Converging System ·Focus ............................... Bi-Potential Electrostatic ·Sweep Deflection ..................................... Magnetic ·Picture Intermediate Frequency
·Adjacent Picture Carrier Trap
·Aerial Input Impedance
·Tuning Ranges ......... 48.25MHz thru 855.25 MHz
B/G ................................................. 38.9MHz D/K ................................................. 38.9MHz
·White Level
Set the brightness control, with no signal connected, so that the CRT cathode current is 600µA. The maximum correction applied to each cathode current to achieve a screen temperature of 7250 degrees K-11 MPCD should not exceed 15% of its original value.
X 0.304 + 0.015
Y 0.306 + 0.015
Screen temperature 7250º K-11 MPCD
Specifications are subject to change without prior notice.
MODEL DIFFERENCES AND DESTINATION (Operation Manual languages) 21HT15C: 21HT15CS: 21HT16C: 21HT16CS: English, Polish, Russian, Czech, Slovak, Hungarian, Romanian. Silver Cab. English, Polish, Russian, Czech, Slovak, Hungarian, Romanian. Cyrillic European TXT. English, Polish, Russian, Czech, Slovak, Hungarian, Romanian. Cyrillic European TXT, Silver Cab. English, Polish, Russian, Czech, Slovak, Hungarian, Romanian.
WARNING The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to qualified service personnel.
3
21HT-15C 21HT-16C
IMPORTANT SERVICING NOTES
Only qualified service personnel are allowed to carry out maintenance and repair of this receiver.
Servicing of high voltage system and CRT
It is important that the static charge is removed from the high voltage system when carrying out work on the receiver. This can be achieved by connecting a 10K resistor (with a suitably insulated lead) from the CRT cavity connector to the CRT ground tag. This must be carried out with the AC supply disconnected from the receiver. Note the following: · The CRT in this receiver employs Integral Implosion Protection. · If the CRT has to be changed it MUST be replaced with the correct type for continued safe working · DO NOT lift the CRT by its neck. · When handing the CRT, ensure that shatterproof goggles are worn. · Ensure that the CRT is discharge before handling.
X-Ray
This receiver is designed to keep any x-ray emission to an absolute minimum. Some fault conditions and servicing procedures may produce potentially hazardous x-ray radiation levels. This is a problem when in close proximity to the receiver for long periods of time. To reduce any risks associated with this, please observe the following precautions: 1. When undertaking any servicing on this chassis, DO NOT increase the EHT to more than 30.5 KV, (at a instantaneous beam current of 1300µA). 2. Ensure that during normal operation the EHT does not exceed 25.0 KV±1.5KV (at a beam current of 1100µA). This level has been preset in the factory. Always check that this level has not been exceeded after carrying out any repair on the receiver. 3. DO NOT replace the CRT with any other type than that specified in the parts listing as this may cause excessive x-ray radiation.
Before returning the receiver to the customer
In addition to the above checks, the following should also be carried out before returning the receiver to the customer. 1. Inspect all the leads to ensure that they are dressed correctly and that they are not obstructed or pinched by any other parts. 2. Ensure that all protective devices are in good condition. These will include nonmetallic control knobs, insulating fish papers, cabinets backs, compartment covers or shields, mechanical insulators, etc.
4
21HT-15C 21HT-16C
CONTROLS & TERMINALS
Remote Control
Infrared Transmitter Window Aim this window at the infrared sensor on your TV set TV/VIDEO Select button Single/Double Entry button ( )
CALL ( SOUND MUTE ( POWER/STANDBY (
)/CHILD LOCK ( ) button ) button
) button
TV/VIDEO
Programme Select buttons
1
FLASHBACK ( ) button Returns to previously viewed programme VOLUME UP ( )/DOWN ( ) button ( ) Increases sound ( ) Decreases sound (These are also used for menu set up)
2 5 8 0
3 6 9
MENU
CHANNEL (PROGRAMME) UP ( 6
4 7
)/ DOWN ( ) button ( ) Selects next higher programme ( ) Selects next lower programme (These are also used for menu set up) )
CH CH
Text/Mix/Picture ( Select button (Teletext)
CLOCK ( REVEAL ( HALF PAGE ( CANCEL ( RESET (
) button (Teletext)
?)
COLOUR buttons
? I
button (Teletext)
X
INDEX ( HOLD (
I
) button (Teletext) ) button (Teletext)
i
S
) button (Teletext)
X)
LIST
button (Teletext)
TV/TEXT REMOTE CONTROL
LIST Select button (Teletext) 25 STORE (
S
i
) button (Teletext)
) button (Teletext)
TV Front
MENU CH
Power (
) button Channel Up ( Volume Up ( Menu button )/Down ( ) buttons
Power/On Timer indicator Remote Control Sensor
)/Down (
) buttons
Euro-SCART 21-Pin Terminal
For greater A/V enjoyment, various audio and video devices may be connected via the Euro-SCART 21-Pin Terminal.
21-Pin Euro-SCART
1. 2. 3. 4. 5. 6.
Audio right output Audio right input Audio left output Common earth for audio Earth for blue Audio left input
7. Blue input 8. Audio-video control 9. Earth for green 10. Not used 11. Green input 12. Not used
13. Earth for red 14. Not used 15. Red input 16. Red/Green/Blue control 17. Earth for video 18. Earth for video
19. Video output 20. Video input 21. Plug shield
5
21HT-15C 21HT-16C
SERVICE ADJUSTMENTS
· Service Mode function
All required adjustments for servicing this TV set, may be done in "service mode", excepting G2 and FOCUS. How to access the Service Mode 1. 2. 3. 4. 5. 6. 7. Turn the receiver on and ensure that it is tuned into a test pattern. Turn the receiver off using the mains switch. Press the volume down and channel up buttons together. See Fig.1. Continue pressing the volume down and channel up buttons while turning the mains on using the mains switch. See Fig.1. Keep pressing the volume down and channel up buttons until the picture appears. When <> appears on the screen, release the two buttons. The receiver is now in the service mode. Fig. 1
To move between the various service mode functions, use the channel up and down buttons. Use the volume buttons to change the data to the desired value. The data will be stored automatically when exiting the service mode. To exit the service mode press the stand-by button on the remote control or turn the receiver off with the mains switch.
Fig. 2
Fig. 3
SHARP X
X VXX.XX Adjustment (Yellow) XXXX: XX: Value (Green)
STS0: XXXX XXXX STS1: XXXX XXXX STS2: XXXX XXXX
6
21HT-15C 21HT-16C
· Service adjustment and data list
The table below shows the various service mode positions, range of values and default value. The columns are headed as below. Heading: OSD Function Range Initial Default FIX/ADJ Descriptions: This is what will appear on the screen at this position. This is the description of the mode's function. This is the range of values that can be entered while in this mode. This is the initial value, i.e. just after changing the NVM. Shadowed values are those to be modified in Default. This is the recommended default value for this mode. If this is ADJ, then it may be necessary to adjust this value away from the default.
No. OSD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 AGC V-LIN V-AMP V-CENT H-CENT H-CENT60 EW / / HB S-COR DRI-RS DRI-GS DRI-BS DRI-RW DRI-GW DRI-BW DRI-RC DRI-GC DRI-BC SUB-VOL SUB-CON SUB-COL SUB-BRI TINT SUB-SHP HTL-VOL
Function AGC Take Over Point Vertical Slope [VS] Vertical Amplitude [VA] Vertical Shift [VSH] Horizontal shift [HS] offset to H-CENT for60 Hz Horizontal Parallelogram [HP] Horizontal Bow S-Correction [SC] White point Red Standard white temp. White point Blue Standard white temp White point Red Warm white temp. White point Green Warm white temp. White point Blue Warm white temp. White point Red Cold white temp. White point Green Cold white temp. White point Blue Cold white temp. Max Volume Sub Contrast Sub Colour Sub Brightness Sub Tint Sub Sharpness Max Hotel Volume
Range 0...63 0...63 0...63 0...63 0...63 0...31 data(-16..+15) 0...63 0...63 0...63 0...63 0...63 0...32 0...32 0...32 0...32 0...32 0...32 0...63 0...63 0...63 0...63 0...63 0...63 0...63
Initial 14 32 32 32 32 16 32 32 0 32 32 32 16 16 16 16 16 16 60 63 32 32 32 32 30
Default 34 33 18 17 34 20 32 32 22 42 42 42 16 9 9 9 9 16 60 63 25 34 32 11 30
FIX/ADJ ADJ ADJ ADJ ADJ ADJ FIX FIX FIX FIX ADJ ADJ ADJ FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX
White point Green Standard white temp. 0...63
7
21HT-15C 21HT-16C
No. OSD 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 HTL-PRG RGB SEARCH-SYS CUT-R CUT-G CDL DL-PT DL-ST DL-4T COL-OP COL-OS COL-O4 SHP-OP SHP-OS SHP-O4 SC-VOL PRE-SC PRE-FM PRE-NICAM AVC-DKY AC-OFF-TIM DISP
Function Hotel Program number OSD RGB Reference Sound system for auto turning Black Level off-set R [BLR] Black Level off-set G (BLG) Cathode Drive Level [CL] Y-Delay time for PAL (TV) [YD] Y-Delay time for SECAM (TV) [YD] Y-Delay time for N443 (TV) [YD] COLOUR OFFSET (PAL) COLOUR OFFSET (SECAM) COLOUR OFFSET (NTSC443) SHARPNESS OFFSET(PAL) SHARPNESS OFFSET(SECAM) SHARPNESS OFFSET(NTSC443) SCART volume Prescaler SCART input Prescaler FM/AM Prescaler SCART input AVC Decay Time to set the AC-OFF timer is in steps of 10minutes Language or symbols
Range 0...99 or > 99 for none 0...15 0(L-BG),1(BG),2(I),3(DK) 0...63 0...63 0...15 0...15 0...15 0...15 0...15 0...15 0...15 0...15 0...15 0...15 0..255 0..127 0..127 0..127 1...4 data(1.2.4.8.) 0..15 0(symboles), 1(English), 2(French) 0 (teletext pan-european language) 1 (second language;cyrillic) 2(third language;Greek) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 for 1 AV or 1 for 2 AV 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (westem) or 1 (eastem) 0 (disable) or 1 (enable) 0 for Ph1 or 1 for Ph2 0 (fast tuning) or 1 (moderate speed tuning) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 or 1 0 (disable) or 1 (enable)
Initial 255 15 1 0 0 0 12 15 12 8 8 4 8 4 8 115 25 72 0 2 0 0
Default 255 0 3 0 10 5 4 8 8 8 8 4 8 4 8 115 25 72 0 2 0 0
FIX/ADJ FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX
48
TXT-EUR
Teletext pan-European language
0 0 1 0 0 0 0 1 1 1 1 1 0 0 1 0 1 0 1 0 0 0 1 1 0 0 0 0 0 0 0 0 0 1
0 (...15C) FIX 1 (...16C) 1 1 0 1 0 1 0 1 1 1 0 0 0 0 1 0 1 0 0 0 1 1 1 1 0 0 0 0 0 0 1 1
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
BKS AVC FFI ACL S-L S-DK S-I S-BG BLUE-BACK VMC HTL BTSC AV FMWS SM0 SM1 AGC0 AGC1 FOA-FE FOB-FE FOA-AV FOB-AV TXT TXT-W/E FSL HP2 CP
Black Stretch Automatic Volume Control(AVL) Fast Filter IF-PLL Auto Colour Limit Sound system L Sound system DK Sound system I Sound system BG Video mute at Ident loss Video Mute at program/source Change Hotel mode Reduced FM demodulator Gain (for BTSC sig) Number of external AV sources FM Window Selection Sound Mute bit 0 Sound Mute bit 1 IF AGC speed bit0 IF AGC speed bit1 Phi 1 time constant for FE(RF) Phi 2 time constant for FE(RF) Phi 1 time constant for AV Phi 2 time constant for AV Teletext Teletext Western or Eastern characters Forced V-SYNC slicing level Sync of OSD Charge pump NICAM decoding enabled IGR decoding enabled Start auto tuning at POWER-ON Function of TXT key Enable Vertical Guard
FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX
76 NICAM 77 IGR 78 AUTO 79 TXT-TGL 80 EVG
8
21HT-15C 21HT-16C
· Screen adjustment
1. G2 Adjustment 1. 2. 3. 4. 5. 6. 7. 8. 9. Enter the service mode (see page 6). Use the channel up or channel down buttons to enter the << BLUE-BACK >> function. Set this to << BLUE-BACK: 0 >>, i.e. blue background is turned off. Turn the set off at the mains. Turn the set back on. Set the picture control settings to normal. Select the SCART input by pressing the TV/SCART button on the remote control. Do not connect an input to the SCART socket. A blank raster will appear. Connect an oscilloscope to TP851 on the CRT PWB. The waveform as in figure 4 should be displayed. Adjust the G2 control (screen voltage) so that the peak of this waveform is 3.0V +/-0.1V above the zero volt line.
9GF
9
9
Fig. 4
10. Enter the service mode. 11. Turn the blue background function back on again - set << BLUE-BACK: 1 >>. 12. Turn off the receiver using the mains button. 13. The G2 adjustment is now complete.
2. Focus Adjustment 1. 2. 3. Receive a monoscope pattern signal at a level of 60 to 80 dBµV. Set the picture settings to normal. Adjust the focus potentiometer to obtain maximum definition.
· AGC Adjustment
1. 2. 3. 4. 5. 6. 7. 8. Tune the receiver into a colour bar signal on channel E-12. Set the RF generator to an output signal strength of 59 dB/µV (+/-1dBµV) 75 Ohms. Connect an oscilloscope to TP201. TP201 is one end of R201. Enter the service mode (see page 6). Use the channel up and channel down buttons to enter the AGC mode. By using the volume up and the volume down buttons, adjust the AGC until the voltage on TP201 drops by 0.1V to 0.3V below its maximum value. Change the input signal strength to 66-70dBµV and make sure that there is no noise apparent in the picture. Turn the receiver off at the mains, this will exit the service mode and store the adjustment.
9
21HT-15C 21HT-16C
· Geometry adjustment procedure
To adjust the geometry, follow the procedure outlined below: 1. Tune the set into a Philips test pattern. 2. Enter the service mode as described on page 6. 3. Use the channel up or channel down buttons to enter the desired mode 4. Use the volume buttons to achieve correct setting. 5. When adjustments are complete, use the stand-by button to turn off the set. The adjustment values will be stored at this point.
V-LIN Adjust the vertical linearity control so that the picture centring is as shown in figure 5.
Fig. 5 V-AMP Adjust the vertical amplitude control so that the picture overscans as shown in figure 6.
Fig. 6 V-CENT Adjust the vertical centring control so that the picture is centred as shown in figure 7.
Fig. 7 H-CENT Adjust the horizontal centring control so that the picture is centred as shown in figure 8.
Fig. 8
10
21HT-15C 21HT-16C
· Colour adjustment procedure
The following adjustments should only be carried out when the CRT or IC801 are replaced. Notes:
· This adjustment must be done after warming up the unit for 30 minutes or longer with a beam current over 700 µA. · The red value «DRI-RS» should be fixed to 42. (Refer to "How to access service mode" section). · «DRI-GS» adjustment alters "Y" coordinate. · «DRI-BS» adjustment alters "X" and "Y" coordinates.
Adjustment method 1 (using the signal generator, varying the picture signal) 1. 2. 3. 4. 5. Adjust G2. Input a white pattern with burst signal from SCART. Position the colorimeter in the centre of screen. Adjusting input signal level, select a luminance of 70 nits. Operate again in "service mode" and select «DRI-GS» and/or «DRI-BS» locations to obtain colour coordinates:
X 0.304 + 0.015
Y 0.306 + 0.015
Screen temperature 7250º K-11 MPCD
6. Reset the T V with the mains switch button to store the adjustment and exit service mode. 7. Check colour coordinates "X" and "Y" at 20 a 120 Nits. It may be necessary to repeat the same procedure to obtain the above values.
Adjustment method 2 (using the signal generator, with a fixed picture signal) 1. 2. 3. 4. 5. Adjust G2. Tune a white pattern with burst signal. Operate in "service mode": Using «SUB-CON», select a luminance of 70 nits. Operate again in "service mode" and select «DRI-GS» and/or «DRI-BS» locations to obtain colour coordinates:
X 0.304 + 0.015
Y 0.306 + 0.015
Screen temperature 7250º K-11 MPCD
6. Select «SUB-CON». Return data to "63". 7. Reset the TV with the mains switch button to store the adjustment and exit service mode. 8. Check colour coordinates "X" and "Y" at 20 a 120 Nits. It may be necessary to repeat the same procedure to obtain the above values.
11
21HT-15C 21HT-16C
HOTEL MODE FUNCTIONS
The following procedure details how to set up the Hotel Mode Functions. 1. Short Description 1.1. Hotel Mode "HTL": Main Hotel Mode. It deactivates "Channel Setting" functions. It reduces the Maximum Volume. 1.2. Hotel Mode "HTL-VOL": Maximum Volume Level Regulation. 1.3 Hotel Mode "HTL-PRG": Fixing start up program when the TV set is switched on.
2. Before start 2.1. It is necessary to program "Channel Setting" before setting up Hotel Mode "HTL" because after that Channel Setting are deactivated. 2.2. Consider that regarding TXT Features, after activate any of the Hotel modes in the "List Mode" will not be stored any page. 2.3. Consider that changed video control values are not stored. 3. Procedure 3.1. Hotel Mode "HTL" (Main Hotel Mode). 3.1.1. Previous Service Information: Initial Value: 0. Range: 0 to 1. Service Mode Indication: HTL. 3.1.2. Access the Service Mode (see this procedure on page 6). 3.1.3. Select "HTL" by using channel up/down buttons. 3.1.4. Change initial value from "0" (off ) to "1" (on). 3.1.5. Notes: 3.1.5.1. The maximum volume level has been reduced from 60 to 30. For other value go to 3.2. Hotel Mode "HTL-VOL" 3.1.5.2. "Channel Setting" functions have been deactivated. 3.1.5.3. It is necessary to select Hotel Mode "HTL" to be able to set up Hotel Mode "HTL-VOL" or Hotel Mode "HTL-PRG". 3.1.5.4. If you do not need to set up Hotel Mode "HTL-VOL" or "HTL-PRG" get out from Service Mode (To exit the Service Mode press the stand-by button on the remote control or turn the receiver off with the mains switch). 3.2. Hotel Mode "HTL-VOL" (Maximum Volume Level Regulation) 3.2.1. Previous Service Information: Initial value: 30. Range: 0 to 60. Service Mode indication: HTL-VOL. 3.2.2. To activate this Hotel Mode it is necessary activate previously Hotel Mode "HTL". Then the maximum volume level changed fro 60 to 30 as initial value.
12
21HT-15C 21HT-16C
3.2.3. Select "HTL-VOL" by using channel up/down buttons. 3.2.4. Set the value according to your necessities by using volume up/down buttons. 3.2.5. Change initial value from "0" (off ) to "1" (on). 3.2.6. Note: If you do not need to set up Hotel Mode "HTL-PRG" get out from Service Mode (To exit the Service Mode press the stand-by button on the remote control or turn the receiver off with the mains switch).
3.3. Hotel Mode "HTL-PRG" (Fixing start up program when the TV Set is switched on) 3.3.1. Initial value: 255. Range: 0 to 255. Service Mode indication: HTL-PRG. 3.3.2. To activate this Hotel Mode it is necessary activate previously Hotel Mode "HTL". 3.3.4. Select "HTL-PRG" by using channel up/down buttons. 3.3.3. The initial value to 255, ensures that the TV Set starts up in the same program number that it was been displayed before turn it off. 3.3.4 If you want to fix other program number proceed as follows set the value according to your necessities by using volume up / down buttons. Use values between 0 to 99. In this way, the new program number appear fixed when you start up the TV set. Example: If you would like to set starting program number "2", change from 255 to 2. 3.3.5. Get out from Service Mode (To exit the Service Mode press the stand-by button on the remote control or turn the receiver off with the mains switch).
13
21HT-15C 21HT-16C
CHASSIS LAYOUTS
Mother unit
21HS50C
21HS50F
21HS50C
CRT unit
14
21HT-15C 21HT-16C
LED FLASHING CODE
PURPOSE: The led indicates the power mode, occurred I2C error and On timer INPUT: Current power mode - I2C Errors - On timer
Processing: - If in STANDBY mode and On timer inactive then switch LED off. - If in STANDBY and On timer active set LED to blinking, (switch on and off at 1 Hz with a 50% duty cycle). - If in POWER-ON mode, switch LED on. - If an I2C error occurred, let the LED blink at 1 Hz, 50 % duty cycle. For the blinking times see the Table below. Note: Only when an I2C error occurs for a number of times, or for a number of seconds, the I 2C error is handled by the system (that is ,only then the set will go to standby, the led starts blinking).
IC/Module Name
Slave Address
Bus Error LED Remarks Blinking Time 2 3 6 6 512x8 EEPROM,1024x8 EEPROM Address of internal TV processor PLL Tuner
Ref. No.
M24C04, M24C08 TDA935x/6x/8x VTST6HD64 or CTF551 Table Error LED blinking times
A0,A2 8A C0 C0
IC1002 IC801 TU201
PRINTED WIRING BOARDS
F 7341N0 PWB. Components side.
6
5
4
3
2
1 Y 0 X 1 2 3 4 5 6 7 8 9 10
15
21HT-15C 21HT-16C
F 7340N7A PWB. Component side
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 17
2
1 Y 0 X 1 2 3 4 5 6 7 8 9 10 11 12 13
16
21HT-15C 21HT-16C
F 7340N7A PWB. Component side
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 16
2
1 Y 12 13 14 15 16 17 18
17
19
20
21
22
23
24
X
25
21HT-15C 21HT-16C
F 7340N7A PWB. Copper side
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 19
2
1 Y 0 X 1 2 3 4 5 6 7 8 9 10 11 12 13
18
21HT-15C 21HT-16C
F 7340N7A PWB. Copper side
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 18
2
1 Y 12 13 14 15 16 17 18 19 20 21 22 23 24
19
X
25
21HT-15C 21HT-16C
ICs ADDITIONAL INFORMATION
TDA9351(IC801)
QUICK REFERENCE DATA SYMBOL Supply VP IP Input voltages ViVIFrms) ViSIF(rms) ViAUDIO(rms) ViCVBS(p-p) ViCHROMA(p-p) ViRGB(p-p) ViYIN(p-p) ViUVIN(p-p) Vo(IFVO)(p-p) Vo(QSSO)(rms) video IF amplifier sensitivity (RMS value) QSS sound IF amplifier sensitivity (RMS value) external audio input (RMS value) external CVBS/Y input (peak-to-peak value) external chroma input voltage (burst amplitude) (peak-to-peak value) RGB inputs (peak-to-peak value) luminance input signal (peak-to-peak value) U/V input signal (peak-to-peak value) - - - - - - - - - - - 0 - 10 1 1.2 75 60 500 1.0 0.3 0.7 1.4 - - - - - - - µV µV mV V V V V V supply voltages supply current - - 8.0/3.3 135/60 - - V mA PARAMETER MIN. TYP. MAX. UNIT
1.33/1.05 - 2.5 100 500 - 2.0 - - - - - - 5 - - - -
Output signals demodulated CVBS output (peak-to-peak value) sound IF intercarrier output in QSS versions (RMS value) V mV mV mA V mA mA mA
Vo(AMOUT)(rms) demodulated AM sound output in QSS versions (RMS value) Io(AGCOUT) VoRGB(p-p) IoHOUT IoVERT IoEWD tuner AGC output current range RGB output signal amplitudes (peak-to-peak value) horizontal output current vertical output current (peak-to-peak value) EW drive output current
AVL/SNDIF/ REFO/AMOUT
32
MXXxxx
DECDIG
VP2
SECPLL
VSSA
P0.6
P0.5
VSSC/P
P3.3/ADC3
P3.2/ADC2
P3.1/ADC1
P3.0/ADC0
P2.0/TPMW
P1.7/SDA
P1.6/SCL
P1.3/T1
GND2
AUDEEM/SIFIN1 DECSDEM/SIFIN2
TUNERAGC
VSC
IREF
IFIN2
IFIN1
VDRB VDRA
AVL/EWD
DECBG
GND3
PH1LF
PH2LF
SNDPLL/SIFAGC
handbook, halfpage
Pin configuration (SDIP 64)
31 34
30
29
28
27
26
25
24
23
22
21
20
19
18
TDA935X/6X/8X PS/N2
33 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
XXX
EHTO AUDEXT/QSSO/ AMOUT
FBISO HOUT
INSSW2
PLLIF
IFVO/SVO
VP1
CVBSINT
GND1
CVBS/Y
CHROMA
AUDOUT/AMOUT
R2/VIN
G2/YIN
20
B2/UIN
BCLIN
BLKIN
RO
GO
BO
VDDA
VPE
VDDC
OSCGND
XTALIN
XTALOUT
RESET
VDDP
P1.0/INT1
P1.1/T0
P1.2/INT0
SNDIF
RESET
SOUND TRAP SCL SDA +3.3 V VPE VST OUT AUDEXT AUDOUT
BLOCK DIAGRAM
LED OUT (2x)
TDA9351(IC801)
TUNERAGC 10/11 (20) 29 28 (32) 35 1+62-64 DEEMPHASIS ENHANCED 1/10 PAGE MEMORY 80C51 CPU VST PWM-DAC I/O PORTS AUDIO SWITCH (AVL) VOLUME CONTROL I2C-BUS TRANSCEIVER 5-8 44 60 55 59 58 57 3 4 9 2 12 54 56 61
27
37
38
(32) 31
23
IFIN
24
VISION IF ALIGNMENT-FREE PLL DEMOD. AGC/AFC VIDEO AMP.
ADC IN (4x)
I/O PORTS (4x)
40 CVBS ROM/RAM ACQUISITION V TELETEXT
VIDEO SWITCH
H TELETEXT/OSD DISPLAY
CVBS/Y
42
VIDEO IDENT.
CHROMA 43 SYNC REF BASE-BAND DELAY LINE LUMA DELAY PEAKING BLACK STRETCH COR
VIDEO FILTERS
AGC CIRCUIT NARROW BAND PLL DEMODULATOR R G
REF
B BL CONTR/BRIGHTN OSD/TEXT INSERT CCC WHITE-P. ADJ. R G B 51 52 53 49 50 RGB/YUV INSERT RO GO B0 BCLIN BLKIN
21
H-DRIVE V-DRIVE + V GEOMETRY (EW GEOMETRY) 2nd LOOP H-SHIFT 34 16 33 25 26 22 21 36 (20) HOUT V-DRIVE EHTO EWD
13
PAL/SECAM/NTSC DECODER (32)
30
41
18 Y U V
+8V
39
H/V SYNC SEP.
RGB/YUV MATRIX SATURATION YUV/RGB MATRIX 46 47 48 45
14
H-OSC. + PLL
19
H
15
17
R/V G/Y B/U BL
21HT-15C 21HT-16C
Block diagram TDA935X/6X8X PS/N2 with mono intercarrier sound demodulator
21HT-15C 21HT-16C
TDA9351(IC801)
PINNING SYMBOL P1.3/T1 P1.6/SCL P1.7/SDA P2.0/TPWM P3.0/ADC0 P3.1/ADC1 P3.2/ADC2 P3.3/ADC3 VSSC/P P0.5 P0.6 VSSA SECPLL VP2 DECDIG PH2LF PH1LF GND3 DECBG AVL/EWD (1) VDRB VDRA IFIN1 IFIN2 IREF VSC TUNERAGC AUDEEM/SIFIN1(1) DECSDEM/SIFIN2(1) GND2 SNDPLL/SIFAGC(1) AVL/SNDIF/REF0/ AMOUT(1) HOUT FBISO AUDEXT/ QSSO/AMOUT(1) EHTO PLLIF IFVO/SVO VP1 CVBSINT GND1 CVBS/Y CHROMA AUDOUT /AMOUT(1) PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 DESCRIPTION port 1.3 or Counter/Timer 1 input port 1.6 or I2C-bus clock line port 1.7 or I2C-bus data line port 2.0 or Tuning PWM output port 3.0 or ADC0 input port 3.1 or ADC1 input port 3.2 or ADC2 input port 3.3 or ADC3 input digital ground for µ-Controller core and periphery port 0.5 (8 mA current sinking capability for direct drive of LEDs) port 0.6 (8 mA current sinking capability for direct drive of LEDs) analog ground of Teletext decoder and digital ground of TV-processor SECAM PLL decoupling 2nd supply voltage TV-processor (+8V) decoupling digital supply of TV-processor phase-2 filter phase-1 filter ground 3 for TV-processor bandgap decoupling Automatic Volume Levelling /East-West drive output vertical drive B output vertical drive A output IF input 1 IF input 2 reference current input vertical sawtooth capacitor tuner AGC output audio deemphasis or SIF input 1 decoupling sound demodulator or SIF input 2 ground 2 for TV processor narrow band PLL filter /AGC sound IF Automatic Volume Levelling / sound IF input / subcarrier reference output /AM output (non controlled) horizontal output flyback input/sandcastle output external audio input /QSS intercarrier out /AM audio output (non controlled) EHT/overvoltage protection input IF-PLL loop filter IF video output / selected CVBS output main supply voltage TV-processor (+8 V) internal CVBS input ground 1 for TV-processor external CVBS/Y input chrominance input (SVHS) audio output /AM audio output (volume controlled)
22
21HT-15C 21HT-16C
TDA9351(IC801)
SYMBOL INSSW2 R2/VIN G2/YIN B2/UIN BCLIN BLKIN RO GO BO VDDA VPE VDDC OSCGND XTALIN XTALOUT RESET VDDP P1.0/INT1 P1.1/T0 P1.2/INT0 Note
PIN 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 2nd
DESCRIPTION RGB / YUV insertion input 2nd R input / V (R-Y) input 2nd G input / Y input 2nd B input / U (B-Y) input beam current limiter input / (V-guard input, note 2) black current input / (V-guard input, note 2) Red output Green output Blue output analog supply of Teletext decoder and digital supply of TV-processor (3.3 V) OTP Programming Voltage digital supply to core (3.3 V) oscillator ground supply crystal oscillator input crystal oscillator output reset digital supply to periphery (+3.3 V) port 1.0 or external interrupt 1 input port 1.1 or Counter/Timer 0 input port 1.2 or external interrupt 0 input
1. The function of pin 20, 28, 29, 31, 32, 35 and 44 is dependent on the IC version (mono intercarrier FM demodulator / QSS IF amplifier and East-West output or not) and on some software control bits. The valid combinations are given in table 1. 2. The vertical guard function can be controlled via pin 49 or pin 50. The selection is made by means of the IVG bit in subaddress 2BH. Table 1 Pin functions for various versions FM-PLL version QSS version
IC version
East-West Y/N N Y N Y CMB1/CMB0 bits 00 01/10/11 00 01/10/11 00 01/10/11 00 01/10/11 AM bit - - - - - 0 1 - 0 1 Pin 20 AVL EWD AVL EWD Pin 28 AUDEEM SIFIN1 Pin 29 DECSDEM SIFIN2 Pin 31 SNDPLL SIFAGC REFO(2) AMOUT REFO(2) Pin 32 SNDIF(1) REFO(2) AVL/SNDIF(1) REFO(2) AMOUT Pin 35 AUDEXT AUDEXT QSSO AMOUT AUDEXT QSSO AMOUT Pin 44 AUDOUT controlled AM or audio out Note 1. When additional (external) selectivity is required for FM-PLL system pin 32 can be used as sound IF input. This function is selected by means of SIF bit in subaddress 28H. 2. The reference output signal is only available for the CMB1/CMB0 setting of 0/1. For the other settings this pin is a switch output (see also table 67).
23
21HT-15C 21HT-16C
TEA1507(IC701)
ndbook, full pagewidth
VCC
1
SUPPLY MANAGEMENT internal UVLO start supply
START-UP CURRENT SOURCE
8
DRAIN HVS n.c.
clamp VALLEY
7
GND
2
S1
M-level
VOLTAGE CONTROLLED OSCILLATOR
4
LOGIC
100 mV
DEM
FREQUENCY CONTROL
OVERVOLTAGE PROTECTION
OVERTEMPERATURE PROTECTION
LOGIC
DRIVER
Iss
6
DRIVER
CTRL
3
-1
POWER-ON RESET
S
Q
LEB blank
soft start S2
0.5 V
2.5 V burst detect
UVLO
R
Q
5 OCP Isense
TEA1507
MAXIMUM ON-TIME PROTECTION
short winding
0.75 V
OVERPOWER PROTECTION
MGU230
Block diagram.
PINNING SYMBOL PIN VCC GND CTRL DEM Isense DRIVER HVS DRAIN 1 2 3 4 5 6 7 8 ground control input input from auxiliary winding for demagnetization timing, OVP and OPP programmable current sense input gate driver output high voltage safety spacer, not connected drain of external MOS switch, input for start-up current and valley sensing Pin configuration. DESCRIPTION supply voltage
handbook, halfpage
VCC 1 GND 2
8 DRAIN 7 HVS
TEA1507
CTRL 3 DEM 4
MGU231
6 DRIVER 5 Isense
24
21HT-15C 21HT-16C
AN7523(IC303)
Circuit Function Block Diagram
Pin Descriptions
Pin No. 1 2 3 4 5 6 7 8 9 Description Vcc Ch Output (+) GND Ch Output (-) Standby Ch Input GND N.C Volume
VCC 1
2
3
4
5
6
7
8
Standby
Note: Do not apply voltage or current to NC pin from outside
AN5522(IC501)
Volume
Output
Output
GND
GND
Input
N.C.
9
Circuit Function Block Diagram
Pin Descriptions
Pin No. Pin Name Inverting Input Power Supply Pump-up Output GND Vertical Output Vertical Output Power Supply Non-inverting Input
Thermal Protection
1 2 3 4 5 6 7
Pump Up
Amp +
1
Inverting Input
2
Vcc
3
Pump Up Out
4
GND
5
Output
6
Output Vcc
7
Non-inverting Input
25
21HT-15C 21HT-16C
SCHEMATIC DIAGRAMS
Description
Safety note: 1. Disconnect the AC plug from the AC outlet before replacing parts. 2. Semiconductor heat sinks should be regarded as potential shock hazards when the chassis is operating.
Note:
1. The unit of resistance «ohm»is omitted (K=1000 ohms. M= Megaohm). 2. All resistors are 1/16 watt. unless otherwise noted. 3. All capacitors are µF, unless otherwise noted (P= µµF). 4. The capacitor with Part No. RC-FZ9XXXBMNJ is designed to with stand 63V. 5. The capacitor with Part No. RC-FZ4XXXBMNJ is designed to with stand 50V.
Important safety note: Parts marked with « ! » ( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Service precaution: The area enclosed by this line is directly ( ) connected with AC mains voltage. When servicing the area, connect an insulating transformer between TV receiver and AC line to eliminate hazard of electric shock.
CAUTION This circuit diagram is original one, therefore there may be slight difference from yours.
Waveform measurement condition: Colour bar generator signal of 70 dB from RF input.
Waveforms
26
21HT-15C 21HT-16C
27
21HT-15C 21HT-16C
Schematic Diagram of Mother Unit (F7340N7A, 00 Version)
I
H
G
F
E
D
C
B
Page 29
A
1
2
3
4
5
6
7
28
21HT-15C 21HT-16C
Schematic Diagram of Mother Unit (F7340N7A, 00 Version)
I
H
G
F
E
D
C
B
Page 30
Page 28
A
8
9
10
11
12
13
14
29
21HT-15C 21HT-16C
Schematic Diagram of Mother Unit (F7340N7A, 00 Version)
I
H
G
F
E
D
C
Page 29
B
A
8
9
10
11
12
13
14
30
21HT-15C 21HT-16C
Schematic Diagram of CRT Unit (F7341N0, 00 Version)
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
31
21HT-15C 21HT-16C
BLOCK DIAGRAMS
Mother Unit
I
H
G
F
E
D
C
B
Page 33
A
1
2
3
4
5
6
7
32
21HT-15C 21HT-16C
Mother Unit
I
H
G
F
E
D
C
B
Page 32
A
8
9
10
11
12
13
14
33
21HT-15C 21HT-16C
CRT Unit
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
34
21HT-15C 21HT-16C
TROUBLESHOOTING TABLES
NO RASTER
Check F701
NO Does F701 appear blown out?
YES
Replace the fuse Check T701 pin 16 voltage.
NO
Does F701 appear blown out again?
YES
NO
Does 290V appear at pin (16) of T701 (SMT Transf.)
YES
END Check R701,S701 and AC in. NO YES
Check IC701, D701, D702, D703, D704, C705, Q701
Does 110V appear in Main+B C752) ?
Check F751, D758, C702 IC702, Q752 and R615 line
NO
Check D1001 Does Power LED bright red Turn on?
YES
NO
Check CRT connector K1-K5 BIAS
YES
See Many often D1001 Flashes in red, this indicates which IC to check up.
Check C878
Check IC801 Heater
Explanation: NVM (IC1002) TV Processor (IC801) TUNER (TU201) Power LED dark red Protector Circuit
(R1028,D615,D612,D509,D510,D614,D604,D605,Q603)
2 Times Flash 3 Times Flash 6 Times Flash
35
21HT-15C 21HT-16C
NEITHER VERTICAL NOR HORIZONTAL SYNCHRONIZATION
CIRCUIT TO BE CHECKED: Sync. Separator Circuit.
Check pin33 and 34 of IC801.
DEFECTIVE VERTICEL AMP. AND VERTICAL LINEARITY
Readjusted vertical size. (Bass Data)
Vertical linearity and size is abnormal.
Check R502,R505
NO VERTICAL SCAN
Check IC501 bias. Normal Abnormal
Check C502 and C514.
Check IC501.
NO SPECIFIC COLOUR
NO YES
Is some colour produced in B/W broadcast reception? Check IC801,R801,R802, R803,D804,D805,D806 and Q801.
YES
Is the white balance properly adjusted?
NO
Readjusted the white balance.
The picture colour is cyan.
The picture colour is magenta.
The picture colour is yellow.
Check Q870,Q885 and their adjacent circuits.
Check Q871,Q883 and their adjacent circuits.
Check Q872,Q887 and their adjacent circuits.
36
21HT-15C 21HT-16C
NO PICTURE, NO SOUND
CIRCUITS TO BE CHECKED: Tuner. PIF. Automatic Gain Control. 5V, 32V Power Source.
Does the noise level increase at max. Contrast,Brightness and Sound controls?
Noise increase but no signal is received.
No snow noise.
Check the tuner supply voltage LB and HB must be approx. 5V, BT must be approx. 32V,and CH preset data check.
Does noise or signal appear at pin40 of IC801?
NO YES
Normal
Does noise or signal appear at pin38 of IC801?
NO YES
Check IC801 and its related circuit.
Check the tuner AGC at TP201. Normal Abnormal
Does noise or signal appear at pin23 and 24 of IC801?
NO YES
Check Q401 Q402 and related circuit.
Check pin38 of IC801.
Check pin27 of IC801,Tuner and related circuit.
Check pin1,2 of SF201,Tuner and related circuit.
Check pin37 of IC801 and related circuit.
NO SOUND CIRCUITS TO BE CHECKED: Audio Output Circuit. NO Does signal appear at pin6 of IC302/303? YES Check Speaker. NO Check IC302/303 and peripheral circuit. Check IC3001 and its related circuit.
37
21HT-15C 21HT-16C
PARTS LISTING
REPLACEMENT PARTS
Replacement parts which have special safety characteristics are identified in this manual. Electrical components having such features are identified by ! in the Replacement Part List. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended is not permitted. Replacement parts not shown in this service manual may create shock fire, or other hazards.
REF No.
D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D 0201 0303 0351 0451 0452 0453 0454 0456 0457 0501 0502 0503 0504 0505 0507 0508 0509 0510 0601 0602 0603 0604 0605 0606 0607 0608 0609 0610 0611 0612 0614 0615 0631 0632 0701 0702 0703 0704 0705 0708 0709 0751 0752 0753 0754 0755 0756 0759 0804 0805 0806 0807 1001
PARTS
RH-EX0676GEZZ RH-DX0045BMZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-DX0131CEZZ RH-DX0441CEZZ RH-EX0684GEZZ RH-EX0684GEZZ RH-DX0131CEZZ RH-EX0603GEZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-EX0627GEZZ RH-DX0302CEZZ RH-DX0045BMZZ RH-DX0131CEZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-EX0653GEZZ RH-DX0577BMZZ VHD1SS244//-1 RH-DX0045BMZZ RH-EX0615GEZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-EX0627GEZZ RH-DX0045BMZZ RH-DX0571BMZZ RH-DX0571BMZZ RH-DX0571BMZZ RH-DX0571BMZZ VHD1SS244//-1 RH-DX0045BMZZ RH-EX0656GEZZ RH-DX0302CEZZ RH-DX0064GEZZ RH-EX0612GEZZ RH-DX0302CEZZ RH-DX0045BMZZ RH-EX0615GEZZ RH-DX0045BMZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-PX0013PEZZ
DESCRIPTION
ZENER DIODE MTZJ33CT ROHM DIODE 1N4148 ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC DIODE EU-1 SANKEN DIODE IN4002G23 GENERAL INSTRUMENT ZENER DIODE MTZJ39BT ROHM ZENER DIODE MTZJ39BT ROHM DIODE EU-1 SANKEN Z.DIODE MTZJ 3.9A DIODE 1N4148 DIODE 1N4148 ZENER DIODE MTZJ8.2BT ROHM DIODE UZA DIODE 1N4148 DIODE EU-1 SANKEN DIODE 1N4148 DIODE 1N4148 DIODE 1N4148 DIODE ZENER MTZJ18C ROHM DIODE 1N4935 ACPA SW DIODE 1SS244T-72 DIODE 1N4148 ZENER DIODE 5.6V DIODE 1N4148 DIODE 1N4148 DIODE 1N4148 ZENER DIODE MTZJ8.2BT ROHM DIODE 1N4148 DIODE 1N4005 ACPA DIODE 1N4005 ACPA DIODE 1N4005 ACPA DIODE 1N4005 ACPA SW DIODE 1SS244T-72 DIODE 1N4148 ZENER DIODE MTZJ20C ROHM DIODE UZA DIODE AK04V1 SANKEN ZENER DIODE MTZJ5.1BT ROHM DIODE UZA DIODE 1N4148 ZENER DIODE 5.6V DIODE 1N4148 ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC LED L-53ID-13.95L/F
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AB AB AB AB AB AB AB AA AA AB AA AA AA AA AB AA AB AA AA AA AA AE AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AC AA AB AA AA AA AB AB AB AB AB
HOW TO ORDER REPLACEMENT PARTS
To have your order completed promptly and correctly please supply the following information. 1. MODEL NUMBER 3. PART NO. 5. CODE
MARK *: SPARE PARTS
2. REF. NO. 4. DESCRIPTION 6. QUANTITY
DELIVERY SECTION
REF No.
PARTS
VB51EFS83912E
DESCRIPTION PICTURE TUBE
CRT 21" THA51EFS83X391+DYW
* SN CODE EX CODE
S BN CD
!
MISCELLANEOUS PARTS
!
RCILG0408BMZZ LHLDC3009CEFN LHLDC3500BMFW LHLDW1514BM00 QEARC0009BMZZ
DEGUSSING COIL ADG COIL HOLDER HOLDER HOLDER UNEX 2233 C.EARTH ELECTROMONTAJES
S S S S S
AH AA AA AA AB
AP AB AB AA AF
PRINTED WIRING BOARDS (Not replacement item)
DUNTK7340CJV9 ADJUST CHASSIS 21HT15C DUNTK7341BMV9 CRT UNIT 21HT15C S BG S AK BY AV
PWB-A
TU 0201
MOTHER UNIT TUNER
VTUCTF5511+++ TUNER THOMSON S AN AZ
INTEGRATED CIRCUITS
IC 0303 IC 0501 IC 0601 IC 0701 IC 0702 IC 0751 IC 0801 IC 1002 VHIAN7523++-1 VHIAN5522++-1 VHIKA7808AP-1 VHITEA1507/-1 RH-FX0008GEZZ VHITA48M033-1 RH-IX3560CEN1 VHIM24C08W6-1 IC AN7523 MATSUSHITA IC AN5522 MATSUSHITA IC KIA7808API KOREA ELECTRONICS IC TEA1507P/N1 PHILIPS P/COUPLER RANK-S SHARP IC TA48M033F(S) TOSHIBA IC TDA9351PS/N2 PHILIPS IC M24C08-WMN6T ST MICRO S S S S S S S S AC AC AA AC AA AB AV AB AH AG AE AH AD AF BG AF
!
TRANSISTORS
Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q 0331 0341 0342 0351 0352 0401 0402 0451 0501 0502 0601 0602 0603 0604 0605 0631 0701 0752 0753 0754 1005 1006 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC2482//-1 VS2SD2586//1E VS2SC3928AR-1 VS2SC1815GW-1 VS2SA1530ARS1 VS2SA1530ARS1 VSSTP4NC80Z1E VS2SC1815GW-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRT 2SC2482 TOSHIBA TRT 2SD2586 TOSHIBA TRANSISTOR TRT NPN 60V 150MA 400MW smt transistor smt transistor MOS FET STP4NC80ZFP TOMEN TRT NPN 60V 150MA 400MW TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AK AA AA AA AA AH AA AA AA AA AA
PACKAGED CIRCUITS
PR 0701 X 1001 RMPTP0001BMZZ PTC B59250-C1080-B70 RCRSB0300CEZZ CRYSTAL HC-49/U-S 12000KHz-A1 MURATA S AA S AB AD AF
COILS
L L L L L L L L L L L L L L 0201 0204 0308 0351 0353 0354 0403 0451 0602 0701 0801 0802 1002 3030 VP-DF270K0000 VP-DF270K0000 VP-CF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-XF120K0000 VP-DF3R3K0000 RCILP0225CEZZ RCILF0111BMZZ VP-XF100K0000 VP-XF100K0000 VP-XF100K0000 VP-CF3R3K0000 PEAK COIL 27UH 10% PEAK COIL 27UH 10% PEAK COIL 3.3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 12UH 10% 1/8W PEAK COIL 3,3UH 10% COIL SL_A TOKYO COIL HR-19043 PEAK COIL 10UH 10% 1/8W PEAK COIL 10UH 10% 1/8W PEAK COIL 10UH 10% 1/8W PEAK COIL 3.3UH 10% S S S S S S S S S S S S S S AA AA AB AB AB AB AA AB AA AE AA AA AA AB AB AB AB AB AB AB AA AB AD AL AA AA AA AB
DIODES
CERAMIC FILTERS
38
21HT-15C 21HT-16C
REF No.
CF 0401 SF 0201
PARTS
RFILC0168GEZZ RFILC0291BMZZ
DESCRIPTION
SIF TRAP 5.5/6.5MHZ (MRT) SAW FILTER K2955M SIEMENS
* SN CODE EX CODE
S AA S AH AE AP
REF No.
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 0605 0606 0607 0608 0609 0610 0611 0614 0615 0616 0617 0619 0621 0622 0631 0632 0633 0701 0702 0703 0704 0705 0707 0708 0709 0710 0712 0713 0716 0751 0752 0753 0754 0755 0756 0757 0758 0759 0761 0762 0764 0765 0767 0801 0803 0804 0805 0806 0807 0808 0809 0810 0811 0812 0813 0814 0815 0817 0818 0819 0822 0823 1001 1002 1006 1009 1011 1012 1013 1014 1015 1017 1018
PARTS
VCEA0A1AW227M VCEA0A1CW107M VCKYPA1HF103Z VCKYCY1EF104Z VCKYPA2HB102K VCFYSB2EB823J VCFPVC3CA912H VCFPVC2DB564J RC-EZ0724CEZZ VCQYTA1HM104J VCEA0A1HW105M VCEA0A1HW106M VCEA0A2CW105M VCEA0A1CW227M VCKYCY1EF104Z VCKYCY1HB222K VCEA0A1CW107M RC-FZ0176BMZZ RC-KZ0029CEZZ RC-KZ0029CEZZ RC-KZ0029CEZZ RC-EZ0150BMZZ VCEA0A1EW107M VCQYTA1HM104J VCFYFA1HA474J RC-KZ0040CEZZ RC-KZ0105GEZZ VCKYPA1HB102K VCKYPA2HB102K RC-KZ0299CEZZ RC-EZ0724CEZZ VCKYPA1HB102K VCEA0A1CW108M VCEA0A1CW227M VCEA0A0JW227M VCKYPA2HB102K VCEA0A1EW477M VCKYPA1HB102K VCKYCY1EF104Z VCCCPA1HH680J VCEA0A1EW107M VCEA0A1CW107M VCKYCY1HF103Z VCEA0A1CW227M VCFYFA1HA224J VCFYFA1HA224J VCKYCY1HB222K VCEA0A1HW105M VCKYCY1HB472K VCKYCY1HF223Z VCEA0A1CW106M VCEA0A1HW474M VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB561K VCEA0A1CW227M VCKYCY1HF103Z VCKYCY1HF103Z VCEA0A1CW227M VCKYCY1HF103Z VCKYCY1HF103Z VCCCCY1HH330J VCCCCY1HH330J VCKYCY1HF223Z VCEA0A0JW107M VCEA0A0JW107M VCKYCY1EF104Z VCKYCY1HF103Z VCEA0A0JW107M VCEA0A1CW106M VCKYCY1HF103Z VCKYCY1HF103Z
DESCRIPTION
ELEC C 220UF 20% 10V ELEC C 100UF 20% 16V C.CAPACITOR 0.01U-F 50V S CHIP TAPE CAP 0.1UF/25V CERAM C 1NF 10% 500V POL FILM C 82NF 5% 100V PP FILM C 9,1NF 3% 1600V PP FILM C 560NF 5% 200V ELEC C 100UF 160V KMF160VB-100MMC NICHIC F. CAPACITOR 0.1 UF 50 V ELEC C 1UF 20% 50V ELEC C 10UF 20% 50V ELEC C 1UF 20% 160V E CAPACITOR 220UF 16V 6.3x11 S CHIP TAPE CAP 0.1UF/25V S CHIP CAPACITOR 0.0022UF/50V TAPED ELEC C 100UF 20% 16V POL C B81130 100NF 275V X2 CERAM C 10NF 80,20% 250V CERAM C 10NF 80,20% 250V CERAM C 10NF 80,20% 250V ELEC C 100uF 400V LPN100M2GN JAMICON E. CAPACITOR 100UF 25V 6.3x11 F. CAPACITOR 0.1 UF 50 V FILM CAPACITOR 474 MAT CERAM C 820PF 2KV C. CAP 2200PF/4KV-KX C.CAPACITOR 1000PF/50V CERAM C 1NF 10% 500V CERAM C DE1105-979BN821K2K-A3 MURATA ELEC C 100UF 160V KMF160VB-100MMC NICHIC C.CAPACITOR 1000PF/50V ELEC C 1000MF 16V 10X16MM E CAPACITOR 220UF 16V 6.3x11 E CAPACITOR 220UF/6.3V-5X11 CERAM C 1NF 10% 500V ELEC C 470UF 20% 25V C.CAPACITOR 1000PF/50V S CHIP TAPE CAP 0.1UF/25V CERAM C 68PF 5% 50V E. CAPACITOR 100UF 25V 6.3x11 ELEC C 100UF 20% 16V CHIP CAP 0.01UF/50V E CAPACITOR 220UF 16V 6.3x11 PP FILM C 220NF 5% 50V PP FILM C 220NF 5% 50V S CHIP CAPACITOR 0.0022UF/50V TAPED ELEC C 1UF 20% 50V S.CHIP CAP 4700PF/50V T SC CAPACITOR 0.022UF 50V TAPED ELEC C 10UF 20% 16V ELEC C 0,47UF 20% 50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V S. CAPACITOR 560PF/50V E CAPACITOR 220UF 16V 6.3x11 CHIP CAP 0.01UF/50V CHIP CAP 0.01UF/50V E CAPACITOR 220UF 16V 6.3x11 CHIP CAP 0.01UF/50V CHIP CAP 0.01UF/50V S. CHIP CAP 33PF/50V S. CHIP CAP 33PF/50V SC CAPACITOR 0.022UF 50V TAPED ELEC C 100UF 20% 6,3V ELEC C 100UF 20% 6,3V S CHIP TAPE CAP 0.1UF/25V CHIP CAP 0.01UF/50V ELEC C 100UF 20% 6,3V ELEC C 10UF 20% 16V CHIP CAP 0.01UF/50V CHIP CAP 0.01UF/50V
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AC AC AC AD AA AA AA AD AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AC AD AE AA AA AA AA AB AA AA AA AB AC AC AC AL AA AA AB AD AB AA AA AB AE AA AB AB AA AA AB AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA
TRANSFORMERS
! !
T 0601 T 0602 T 0701
RTRNZ0026PEZZ DRIVER TRANSFORMER RTRNF2053CEZZ FBT BSC21-2643S SHENZHEN RTRNW0005CEZZ TRANSF. SMT 130010012 TABUCHI
S AB S AM S AE
AE AY AP
CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 0201 0202 0204 0206 0207 0208 0209 0210 0211 0212 0215 0302 0305 0307 0308 0311 0320 0322 0324 0328 0331 0341 0342 0343 0345 0346 0348 0349 0351 0352 0354 0358 0359 0361 0362 0363 0402 0403 0404 0431 0432 0433 0451 0453 0502 0504 0505 0506 0507 0508 0509 0511 0512 0513 0514 0515 0521 0522 0531 0532 0533 0599 0602 0603 0604 VCEA0A1CW476M VCEA0A1AW107M VCEA0A1HW106M VCKYCY1HF223Z VCKYCY1HB472K VCKYCY1HB821K VCKYCY1EF104Z VCCCCY1HH220J VCKYPA1HF103Z VCKYPA1HF103Z VCCCCY1HH220J VCEA0A1CW106M VCEA0A1EW337M VCEA0A1CW226M VCKYCY1HF103Z VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HF103Z VCKYCY1HB102K VCCCCY1HH221J VCEA0A1HW225M VCKYCY1HB332K VCEA0A1CW106M VCEA0A1CW106M VCKYCY1HB222K VCKYCY1HF103Z VCEA0A1HW105M VCKYCY1HF103Z VCKYCY1HB102K VCEA0A1CW107M VCEA0A1CW107M VCEA0A1CW106M VCKYCY1HB102K VCKYCY1HB102K VCEA0A1CW106M VCKYCY1HB102K VCCCCY1HH220J VCKYCY1HF103Z VCEA0A1CW106M VCKYCY1HF223Z VCKYCY1HB102K VCKYCY1EF104Z VCEA0A1CW106M VCKYCY1HF103Z VCEA0A1EW477M VCKYPA1HB102K VCEA0A1HW107M VCKYPA1HB102K VCKYCY1HF103Z RC-FZ0272CEZZ VCQYTA2AA563J VCKYPA1HB102K VCKYCY1HF103Z VCKYPA2HB102K VCEA0A1EW477M VCQYTA1HM103J VCKYCY1HB102K VCKYPA1HB102K VCKYCY1HB102K VCKYCY1HB102K VCQYTA1HM104J VCKYCY1HB102K VCEA0A1CW477M VCEA0A1CW107M VCKYPA1HF103Z ELEC C 47UF 20% 16V ELEC C 100UF 20% 10V ELEC C 10UF 20% 50V SC CAPACITOR 0.022UF 50V TAPED S.CHIP CAP 4700PF/50V T GRM39B 821K 50 (1608)SMD CAPACITOR S CHIP TAPE CAP 0.1UF/25V S. CHIP CAP 22PF/50V TAPED C.CAPACITOR 0.01U-F 50V C.CAPACITOR 0.01U-F 50V S. CHIP CAP 22PF/50V TAPED ELEC C 10UF 20% 16V ELEC C 330UF 20% 25V ELEC C 22UF 20% 16V CHIP CAP 0.01UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V CHIP CAP 0.01UF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 220PF/50V TAPED ELEC C 2,2UF 20% 50V s.chip cap 3300pf /50v ELEC C 10UF 20% 16V ELEC C 10UF 20% 16V S CHIP CAPACITOR 0.0022UF/50V TAPED CHIP CAP 0.01UF/50V ELEC C 1UF 20% 50V CHIP CAP 0.01UF/50V S. CHIP CAP 0.001UF/50V ELEC C 100UF 20% 16V ELEC C 100UF 20% 16V ELEC C 10UF 20% 16V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V ELEC C 10UF 20% 16V S. CHIP CAP 0.001UF/50V S. CHIP CAP 22PF/50V TAPED CHIP CAP 0.01UF/50V ELEC C 10UF 20% 16V SC CAPACITOR 0.022UF 50V TAPED S. CHIP CAP 0.001UF/50V S CHIP TAPE CAP 0.1UF/25V ELEC C 10UF 20% 16V CHIP CAP 0.01UF/50V ELEC C 470UF 20% 25V C.CAPACITOR 1000PF/50V ELEC C 100UF 20% 50V C.CAPACITOR 1000PF/50V CHIP CAP 0.01UF/50V C POL P 0,39UF 100V POL FILM C 56NF 5% 100V C.CAPACITOR 1000PF/50V CHIP CAP 0.01UF/50V CERAM C 1NF 10% 500V ELEC C 470UF 20% 25V F. CAPACITOR 0.01UF/50V S. CHIP CAP 0.001UF/50V C.CAPACITOR 1000PF/50V S. CHIP CAP 0.001UF/50V S. CHIP CAP 0.001UF/50V F. CAPACITOR 0.1 UF 50 V S. CHIP CAP 0.001UF/50V ELEC C 470UF 20% 16V ELEC C 100UF 20% 16V C.CAPACITOR 0.01U-F 50V S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AC AB AA AA AA AB AA AA AA AA AA AA AA AA AA AA
!
!
39
21HT-15C 21HT-16C
REF No.
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 0201 0202 0208 0209 0290 0302 0303 0306 0310 0312 0313 0331 0332 0333 0339 0340 0341 0342 0343 0344 0345 0351 0352 0356 0357 0359 0360 0362 0363 0364 0365 0366 0367 0390 0391 0401 0403 0405 0406 0407 0408 0409 0451 0452 0453 0454 0455 0456 0457 0458 0459 0460 0461 0490 0491 0492 0501 0502 0503 0504 0505 0507 0509 0511 0512 0513 0514 0515 0516 0517 0518 0531
PARTS
VRD-RA2BE332J VRS-CY1JF681J VRS-CY1JF102J VRS-CY1JF391J VRS-CY1JF000J VRS-CY1JF472J VRD-RA2BE331J VRS-CY1JF392J VRD-RA2BE101J VRS-CY1JF153J VRS-CY1JF223J VRS-CY1JF103J VRS-CY1JF473J VRD-RA2BE103J VRD-RA2BE101J VRS-CY1JF821J VRS-CY1JF101J VRS-CY1JF821J VRS-CY1JF471J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF104J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF104J VRS-CY1JF472J VRS-CY1JF104J VRS-CY1JF561J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF181J VRS-CY1JF102J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE102J VRD-RA2EE750J VRS-CY1JF104J VRS-CY1JF223J VRS-CY1JF562J VRD-RA2EE750J VRD-RA2EE750J VRD-RA2EE750J VRS-CY1JF103J VRD-RA2EE750J VRD-RA2EE750J VRD-RA2BE224J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRD-RA2BE392J VRN-VV3DB2R7J VRD-RA2HD331J VRS-CY1JF181J VRD-RA2BE1R0J VRS-CY1JF181J VRD-RA2BE102J VRD-RA2HD102J VRD-RA2BE100J VRD-RA2BE103J VRS-CY1JF103J VRS-CY1JF153J VRS-CY1JF153J VRS-CY1JF223J VRS-CY1JF334J VRD-RA2BE101J
DESCRIPTION RESISTORS
RES 3,3KOHM 5% 1/8W S. CHIP RES. 680-OHM TAPED S.CHIP RES TAPE 1K OHM SURFACE MOUNT CHIP RESISTOR 390 OHM S. CHIP RES. 0-OHM TAPED S. RES. 4.7K OHM TAPED RES 330 OHM 5% 1/8W S. CHIP RES. 3.9K-OHM TAPED RES 100 OHM 5% 1/8W S CHIP RES. 15K-OHM TAPED S.CHOP REG 22K-OHM T S.C. RESISTOR 10K OHM S. CHIP RES 47K-OHM TAPED RES 10KOHM 5% 1/8W RES 100 OHM 5% 1/8W S. CHIP RES. 820-OHM S. CHIP RES. 100-OHM TAPED S. CHIP RES. 820-OHM S. CHIP RES. 470-OHM TAPED S.CHIP RES TAPE 1K OHM S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 100K-OHM TAPED S.CHIP RES TAPE 1K OHM S.C. RESISTOR 10K OHM S.CHIP RES TAPE 1K OHM S.C. RESISTOR 10K OHM S. RES. 4.7K OHM TAPED S. CHIP RES. 100K-OHM TAPED S. RES. 4.7K OHM TAPED S. CHIP RES. 100K-OHM TAPED S. CHIP RES 560-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 100-OHM TAPED S.CHIP RES TAPE 1K OHM S CHIP RES. 180-OHM TAPED S.CHIP RES TAPE 1K OHM RES 100 OHM 5% 1/8W RES 100 OHM 5% 1/8W RES 1KOHM 5% 1/8W RES 75 OHM 5% 1/4W S. CHIP RES. 100K-OHM TAPED S.CHOP REG 22K-OHM T S. CHIP RES. 5.6K-OHM TAPED RES 75 OHM 5% 1/4W RES 75 OHM 5% 1/4W RES 75 OHM 5% 1/4W S.C. RESISTOR 10K OHM RES 75 OHM 5% 1/4W RES 75 OHM 5% 1/4W RES 220KOHM 5% 1/8W S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED RES 3,9KOHM 5% 1/8W MET FILM R 2,7 OHM 5% 2W RES 330 OHM 5% 1/2W S CHIP RES. 180-OHM TAPED RES 1 OHM 5% 1/8W S CHIP RES. 180-OHM TAPED RES 1KOHM 5% 1/8W RES 1KOHM 5% 1/2W RES 10 OHM 5% 1/8W RES 10KOHM 5% 1/8W S.C. RESISTOR 10K OHM S CHIP RES. 15K-OHM TAPED S CHIP RES. 15K-OHM TAPED S.CHOP REG 22K-OHM T S. CHIP RES. 330K-OHM TAPED RES 100 OHM 5% 1/8W
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA
REF No.
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 0532 0533 0603 0604 0605 0606 0607 0608 0609 0610 0611 0612 0613 0614 0615 0616 0618 0619 0620 0621 0623 0624 0625 0626 0627 0629 0630 0631 0632 0633 0634 0636 0637 0638 0639 0640 0701 0706 0707 0708 0710 0711 0712 0713 0716 0718 0752 0753 0761 0762 0763 0766 0768 0770 0771 0772 0773 0774 0801 0802 0803 0804 0805 0806 0807 0808 0809 1001 1002 1003 1004 1005 1006 1008
PARTS
VRD-RA2BE101J VRD-RA2BE393J VRD-RA2BE102J VRD-RA2HD472J VRS-KT3LB332J VRD-RA2HD102J VRD-RA2BE104J VRN-RV3ABR82J VRD-RA2HD101J VRS-CY1JF102J VRS-CY1JF103J VRD-RA2BE331J VRD-RA2HD184J VRD-RA2HD472J VRD-RA2HD472J VRD-RA2HD182J VRD-RA2BE123J VRS-CY1JF000J VRD-RA2HD220J VRD-RA2HD820J VRG-RL2HB562J VRD-RA2BE123J VRD-RA2BE103J VRS-CY1JF562J VRS-CY1JF103J VRD-RA2EE151J VRD-RA2BE101J VRD-RA2BE391J VRD-RA2BE273J VRS-CY1JF822J VRS-CY1JF102J VRS-CY1JF154J VRS-CY1JF333J VRS-CY1JF221J VRD-RA2BE333J VRD-RA2BE101J VRW-KP3HC5R6K VRD-RA2BE122J VRD-RA2BE393J VRD-RA2BE102J VRN-VV3ABR27J VRD-RA2BE270J VRD-RA2HD100J VRD-RA2BE394J RR-HZ0014GEZZ VRD-RA2BE824J VRD-RA2HD102J VRN-VV3DB5R6J VRD-RA2BE152J VRD-RA2HD184J VRD-RA2BE822J VRD-RA2EE183J VRD-RA2HD124J VRD-RA2HD181J VRD-RA2HD181J VRS-CY1JF333J VRS-CY1JF153J VRS-CY1JF332J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF223J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF181J VRS-CY1JF221J VRS-CY1JF331J VRS-CY1JF681J VRS-CY1JF472J VRS-CY1JF101J VRS-CY1JF000J
DESCRIPTION
RES 100 OHM 5% 1/8W RES 39KOHM 5% 1/8W RES 1KOHM 5% 1/8W RES 4.7KOHM 5% 1/2W MET OX RES 3,3KOHM 5% 3W RES 1KOHM 5% 1/2W RES 100KOHM 5% 1/8W MET FILM R 0,82 OHM 5% 1W RES 100 OHM 5% 1/2W S.CHIP RES TAPE 1K OHM S.C. RESISTOR 10K OHM RES 330 OHM 5% 1/8W RES 180KOHM 5% 1/2W RES 4.7KOHM 5% 1/2W RES 4.7KOHM 5% 1/2W RES 1,8KOHM 5% 1/2W RES 12KOHM 5% 1/8W S. CHIP RES. 0-OHM TAPED RES 22 OHM 5% 1/2W RES 82 OHM 5% 1/2W FUS RES 5,6KOHM 5% 1/2W RES 12KOHM 5% 1/8W RES 10KOHM 5% 1/8W S. CHIP RES. 5.6K-OHM TAPED S.C. RESISTOR 10K OHM RES 150 OHM 5% 1/4W RES 100 OHM 5% 1/8W RES 390 OHM 5% 1/8W RES 27KOHM 5% 1/8W S. CHIP RES. 8.2K-OHM TAPED S.CHIP RES TAPE 1K OHM S CHIP RES. 150K-OHM TAPED S. CHIP RES. 33K-OHM TAPED S. CHIP RES. 220-OHM TAPED RES 33KOHM 5% 1/8W RES 100 OHM 5% 1/8W WOUND RES 5,6 OHM 10% 5W RES 1,2KOHM 5% 1/8W RES 39KOHM 5% 1/8W RES 1KOHM 5% 1/8W MET FILM R .27 OHM 5% 1W RES 27 OHM 5% 1/8W RES 10 OHM 5% 1/2W RES 390KOHM 5% 1/8W high vol. resistor 12m ohm RES 820KOHM 5% 1/8W RES 1KOHM 5% 1/2W MET FILM R 5.6 OHM 5% 2W RES 1,5KOHM 5% 1/8W RES 180KOHM 5% 1/2W RES 8,2KOHM 5% 1/8W RES 18KOHM 5% 1/4W RES 120KOHM 5% 1/2W RES 180 OHM 5% 1/2W RES 180 OHM 5% 1/2W S. CHIP RES. 33K-OHM TAPED S CHIP RES. 15K-OHM TAPED S. CHIP RES. 3.3K-OHM TAPED S. CHIP RES. 100-OHM TAPED S. CHIP RES. 100-OHM TAPED S. CHIP RES. 100-OHM TAPED S. CHIP RES. 100-OHM TAPED S.CHOP REG 22K-OHM T S. CHIP RES. 100-OHM TAPED S. CHIP RES. 100-OHM TAPED S. CHIP RES. 100-OHM TAPED S. CHIP RES. 100-OHM TAPED S CHIP RES. 180-OHM TAPED S. CHIP RES. 220-OHM TAPED S CHIP RES TAPE 330 OHM S. CHIP RES. 680-OHM TAPED S. RES. 4.7K OHM TAPED S. CHIP RES. 100-OHM TAPED S. CHIP RES. 0-OHM TAPED
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AD AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
!
!
40
21HT-15C 21HT-16C
REF No.
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 1009 1014 1015 1016 1017 1018 1019 1020 1022 1023 1024 1025 1026 1027 1028 1029 1033 1034 1035 1036 1037 1038 1040 1041 1043 1044 1047 1048 1052 1053 1054 1056 1057 1058
PARTS
VRS-CY1JF000J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE332J VRD-RA2BE101J VRD-RA2BE332J VRS-CY1JF101J VRS-CY1JF153J VRS-CY1JF101J VRD-RA2BE153J VRS-CY1JF101J VRS-CY1JF122J VRS-CY1JF224J VRS-CY1JF101J VRD-RA2BE101J VRS-CY1JF101J VRS-CY1JF101J VRD-RA2BE332J VRS-CY1JF101J VRD-RA2BE332J VRD-RA2BE101J VRS-CY1JF223J VRS-CY1JF152J VRS-CY1JF152J VRS-CY1JF562J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF391J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF101J
DESCRIPTION
S. CHIP RES. 0-OHM TAPED RES 100 OHM 5% 1/8W RES 100 OHM 5% 1/8W RES 3,3KOHM 5% 1/8W RES 100 OHM 5% 1/8W RES 3,3KOHM 5% 1/8W S. CHIP RES. 100-OHM TAPED S CHIP RES. 15K-OHM TAPED S. CHIP RES. 100-OHM TAPED RES 15KOHM 5% 1/8W S. CHIP RES. 100-OHM TAPED S. RESISTOR 1.2K OHM S. CHIP RES. 220K-OHM TAPED S. CHIP RES. 100-OHM TAPED RES 100 OHM 5% 1/8W S. CHIP RES. 100-OHM TAPED S. CHIP RES. 100-OHM TAPED RES 3,3KOHM 5% 1/8W S. CHIP RES. 100-OHM TAPED RES 3,3KOHM 5% 1/8W RES 100 OHM 5% 1/8W S.CHOP REG 22K-OHM T S. CHIP RES. 1.5K-OHM S. CHIP RES. 1.5K-OHM S. CHIP RES. 5.6K-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED SURFACE MOUNT CHIP RESISTOR 390 OHM S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 100-OHM TAPED S.C. RESISTOR 10K OHM S. RES. 4.7K OHM TAPED S. CHIP RES. 100-OHM TAPED
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
REF No.
RJ 0058 RJ 0059 RJ 0061 RJ 0062 RJ 0064 RJ 0065 RJ 0067 RJ 0068 RJ 0070 RJ 0071 RJ 0072 RJ 0074 RJ 0075 RJ 0080 RJ 0085 RMC1001 S 0701 S 1001 S 1002 S 1003 S 1004 S 1005 SC 0451 VA 0701
PARTS
VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J RRMCU0235CEZZ QSW-P0591CEZZ QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ QSW-K0003AJZZ QSOCZ2107BMZZ RH-VX0047CEZZ
DESCRIPTION
S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED R/M RECEIVER TSOP1838UH1-A VISHAY SWITCH SDDFC3-A ALPS SWITCH SWITCH SWITCH SWITCH SWITCH SOCKET VARISTOR SIOV-S14K420M4 MATSUSHITA
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AD AA AA AA AA AA AF AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AG AL AA AA AA AA AA AE AC
!
PWB-B
Q Q Q Q Q Q 0870 0871 0872 0883 0885 0887 VSBF422////-1 VSBF422////-1 VSBF422////-1 VSBF421////-1 VSBF421////-1 VSBF421////-1
CRT UNIT TRANSISTORS
TRT BF422 PHILIPS TRT BF422 PHILIPS TRT BF422 PHILIPS TRT BF421 PHILIPS TRT BF421 PHILIPS TRT BF421 PHILIPS S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA
MISCELLANEOUS PARTS
! !
DIODES
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AC AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AD AB AB AB AB AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
D D D D D 0811 0812 0880 0881 0882 RH-DX0045BMZZ RH-DX0045BMZZ VHD1SS82///1A VHD1SS82///1A VHD1SS82///1A DIODE 1N4148 DIODE 1N4148 DIODE 1SS82-A HITACHI DIODE 1SS82-A HITACHI DIODE 1SS82-A HITACHI S S S S S AA AA AA AA AA AA AA AB AB AB
F 0701 F 0751 FB 0451 FB 0452 FB 0601 FB 0701 FH 0701 FH 0702 P 0301 P 0601 P 0602 P 0701 P 0702 P 0801 P 1001 RJ 0001 RJ 0004 RJ 0008 RJ 0009 RJ 0010 RJ 0011 RJ 0019 RJ 0020 RJ 0024 RJ 0026 RJ 0027 RJ 0029 RJ 0031 RJ 0033 RJ 0035 RJ 0036 RJ 0044 RJ 0046 RJ 0047 RJ 0048 RJ 0055 RJ 0056 RJ 0057
QFS-C3229CEZZ QFS-J2521CEZZ RBLN-0037CEZZ RBLN-0037CEZZ RBLN-0037CEZZ RBLN-0037CEZZ QFSHD1001BMZZ QFSHD1002BMZZ QPLGN0241CEZZ QPLGN0441CEZZ QPLGN0560CEZZ QPLGN0360CEZZ QPLGN0260CEZZ QPLGN0541CEZZ QPLGN0641CEZZ VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J
FUSE S506-3.15A-A1 TOKYO COMPONENTS FUSE 2,5A 125V LITTELFUSE (KURODA9 BALUN FBA04HA90088-00 T/Y BALUN FBA04HA90088-00 T/Y BALUN FBA04HA90088-00 T/Y BALUN FBA04HA90088-00 T/Y FUSE HOLD.EYF52BC=PANASON FUSE HOLD.EYF52BC=PANASON PLUG PLUG 4PIN CONNECTOR 5 PIN TV-50P-05-V2 A TAIKO CONNECTOR 3 PIN TV-50P-03-V2 A TAIKO CONNECTOR