Text preview for : SONY CPD 100ES X2R CHASSIS.pdf part of Sony CPD 100ES SONY CPD 100ES X2R CHASSIS
Back to : SONY CPD 100ES X2R CHASSI | Home
CPD-100ES
SERVICE MANUAL
CPD-100ES
CPD-100ES
Southern Hemisphere Model Equator Model
Chassis No.SCC-L15B-A
X2R CHASSIS
SPECIFICATIONS
Picture Tube 0.25 mm aperture grill pitch 15 inches measured diagonally 90-degree deflection (14" maximum viewing image) Approx. 284 x 212 mm (w/h) (111/4 x 83/8 inches) Horizontal: Max. 1280 dots Vertical: Max. 1024 lines Horizontal: Max. 1024 dots Vertical: Max. 768 lines Standard image area Deflection frequency AC input voltage / current Dimensions Mass Approx. 270 x 202 mm (w/h) (103/4 x 8 inches) Horizontal: 30 to 70 KHz Vertical: 50 to120 Hz 100 to 120 V, 50-60 Hz, 1.8 A 220 to 240 V, 50-60 Hz, 1.0 A 368 x 373 x 384.5 mm (w/h/d) (141/2 x 143/4 x 151/4 inches) Approx. 14.0kg (30 lb 14 oz)
Video image area
Logical resolution Physical resolution
Design and specifications are subject to change without notice.
TRINITRON® COLOR COMPUTER DISPLAY
MICROFILM
--1--
CPD-100ES
POWER SAVING FUNCTION
This monitor meets the power saving guidelines set by the EPA Energy Star Program as well as the more stringent TC092 guidelines (NUTEK). It is capable of reduced power consumption when used with a computer equipped with Display Power Management Signaling (DPMS). By sensing the absence of the sync signal coming from the computer, it will reduce the power consumption as follows:
CAUTION: The Power Saving function will automati-
cally put the monitor into Active-off state if the power switch is turned on without any video signal input. Once the horizontal and vertical syncs are sensed, the monitor will automatically return to its Normal operation state.
State 1 2 3 4 5
Normal Operation Suspend (1st step of power saving) Active-off (2nd step of power saving) Active-off (3rd step of power saving) Power - Off
Power consumption
<110 W <15 W <15 W <8 W 0W
Required resumption time
u Power indicator
green on
approx. 3 sec. approx. 10 sec. approx. 10 sec.
orange and green flashes alternately orange and green flashes alternately orange on off
TIMING SPECIFICATION
Mode Resolution(H x V) Dot Clock(MHz) Horizontal Hor. Freq. (kHz) H-Total H-Blanking H-Front Porch H-Sync. H-Back Porch H-Active (µsec) Vertical Ver. Freq. (Hz) V-Total V-Blanking V-Front Porch V-Sync. V-Back Porch V-Active (lines) Sync. INT(G) EXT (H/V)/POLARITY EXT (CS)/POLARITY INT/NON INT NO YES -/NO NON INT NO YES -/NO NON INT NO YES +/+ NO NON INT NO YES +/+ NO NON INT NO YES -/NO NON INT NO YES +/+ NO NON INT NO YES +/+ NO NON INT NO YES +/+ NO NON INT NO YES -/+ NO NON INT 59.940 525 45 10 2 33 480 85.008 509 29 1 3 25 480 75.000 625 25 1 3 21 600 85.061 631 31 1 3 27 600 74.550 667 43 1 3 39 624 75.029 800 32 1 3 28 768 84.997 808 40 1 3 36 768 60.020 1066 42 1 3 38 1024 70.087 449 49 12 2 35 400 31.469 31.778 6.356 0.636 3.813 1.907 25.422 43.269 23.111 5.333 1.556 1.556 2.222 17.778 46.875 21.333 5.172 0.323 1.616 3.232 16.162 53.674 18.631 4.409 0.569 1.138 2.702 14.222 49.725 20.111 5.586 0.559 1.117 3.910 14.524 60.023 16.660 3.657 0.203 1.219 2.235 13.003 68.677 14.561 3.725 0.508 1.016 2.201 10.836 63.981 15.630 3.778 0.444 1.037 2.296 11.852 31.469 31.777 6.355 0.636 3.813 1.907 25.422 1 640 x 480 25.175 2 640 x 480 36.000 3 800 x 600 49.500 4 800 x 600 56.250 5 832 x 624 57.283 6 1024 x 768 78.750 7 8 9 720 x 400 28.322
1024 x 768 1280 x 1024 108.000 94.500
--2--
CPD-100ES
TABLE OF CONTENTS
Section Title Page
1. GENERAL ................................................................................... 4
2. DISASSEMBLY
2-1. 2-2. 2-3. 2-4. Cabinet Removal ............................................................7 Service Position ...............................................................7 D Board Removal ............................................................7 Picture Tube Removal ................................................... 8
3. SAFETY RELATED ADJUSTMENT................................. 9 4. ADJUSTMENTS ........................................................................ 10 5. DIAGRAMS
5-1. BlockDiagram .................................................................15 5-2. Circuit Boards Location ................................................. 18 5-3. Schematic Diagrams and Printed Wiring Boards ...... 18 1. D Board - Schematic Diagram ................................. 19 2. A Board - Schematic Diagram ................................. 23 5-4. Semiconductors ..............................................................27
6. EXPLODED VIEWS
6-1. Chassis ............................................................................ 29 6-2. Packing Materials .......................................................... 30
7. ELECTRICAL PARTS LIST ................................................ 31
--3--
CPD-100ES
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
SECTION 1 GENERAL
Getting Started
Before using this monitor, please make sure that the following items are included in your package: Multiscan 100ES/200ES monitor (1), power cord (1), warranty card (1), "Windows95 Monitor Information Disk" (1), and this operating instruction manual (1). This monitor will sync with any IBM or compatible system equipped with VGA or greater graphics capability. Although this monitor will sync to other platforms running at horizontal frequencies between 30 and 70 kHz, including Macintosh and Power Macintosh system, a cable adapter is required. Please consult your dealer for advice on which adapter is suitable for your needs. Step 1: With the computer switched off, attach the video signal cable to the video output.
Using Your Monitor
Preset and User Modes
The Multiscan 100ES/200ES has factory preset modes for the 8 most popular industry standards for true "plug and play" capability. For less common modes, the Multiscan 100ES/200ES's Digital Multiscan Technology will perform all of the complex adjustments necessary to ensure a high quality picture for any timing between 30 and 70 kHz.
Adjustments
When one of the preset-type signals is input, no picture adjustment is necessary. You can, however, adjust the picture to your preferences by following the procedure described below. You can adjust all items on the OSD (On Screen Display).
Control Panel
p p
Before adjusting the items, turn on the unit and feed the video signal from the connected computer/work station. Adjustments will be stored automatically.
CPD-100ES/100EST and CPD-200ES/200EST
No. Resolution Horizontal Vertical Graphics (dots × lines) Frequency Frequency Mode 1 2 3 4 5 640 × 480 640 × 480 800 × 600 800 × 600 832 × 624 1024 × 768 1024 × 768 1280 × 1024 31.5 kHz 43.3 kHz 46.9 kHz 53.7 kHz 49.7 kHz 60.0 kHz 68.7 kHz 64.0 kHz 60 Hz 85 Hz 75 Hz 85 Hz 75 Hz 75 Hz 85 Hz 60 Hz VGA Graphic 1) VESA 2) VESA 2) VESA2) Macintosh 16" Color 2) VESA 2) VESA 2) VESA 2)
RESET
COLOR
GEOM
SIZE
CENTER
Adjusting the Picture Contrast
The adjustment data becomes the common setting for all input signals.
Adjusting the Picture Centering
The adjustment data becomes the individual setting for each input signal received.
1
IBM or compatible computer to video output
6 7 8
Press the > ?// button. The "BRIGHTNESS/CONTRAST" OSD appears.
BRIGHTNESS/CONTRAST 100 50
1
Press the CENTER button. The "CENTER" OSD appears.
CENTER
CENTER 32 68
--4--
Apple computer to video output Macintosh adapter (not supplied)
For the customers using the Windows®4)95 Install the new model information of the Sony computer display
from "Windows95 Monitor Information Disk" into your PC. (To install the file, refer to the attached "About the Windows95 Monitor Information Disk/File".)
3 1 . 5 kHz/70Hz
2
Horizontal frequency Vertical frequency
For vertical adjustment Press the ¨ >/. buttons.
Step 2:
Attach the power cord to the monitor and the other end to a power outlet.
Power cord (supplied) to a power outlet
This monitor complies with "VESA DDC", the standards of Plug&Play. If your PC/graphic board complies with DDC, select "Plug and Play Monitor (VESA DDC)" or this monitor's model name (CPD-100ES/100EST or CPD-200ES/ 200EST) as "Monitor type" from "Control Panel" on Windows95. Some PC/graphic boards do not comply with DDC. Even if they comply with DDC, they may have some problems on connecting to this monitor. In this case, select this monitor's model name (CPD-100ES/100EST or CPD200ES/200EST) as "Monitor type" on Windows95.
Recommended horizontal timing conditions
Horizontal sync width should be: >1.0 µsec. Horizontal blanking width should be: >3.6 µsec. (Multiscan 100ES)/ >3.0 µsec. (Multiscan 200ES). Vertical sync width should be: < 560 µsec.
2
Press the > ?// buttons to adjust picture contrast. / . . . for more contrast ? . . . for less contrast > . . . to move up . . . . to move down For horizontal adjustment Press the > ?// buttons.
The "BRIGHTNESS/CONTRAST" OSD disappears 3 seconds after you release the buttons. To reset, press the RESET button while the OSD is on.
Adjusting the Picture Brightness
The adjustment data becomes the common setting for all input signals.
Step 3: Step 4:
Turn on the monitor and computer. If necessary, adjust the user controls according to your personal preference.
Note
CPD-100ES/100EST and CPD-200ES/200EST does not apply to Macintosh 21" color mode.
1
The installation of your Multiscan 100ES/200ES is complete. Enjoy your monitor. 1) VGA is a trademark of IBM Corporation. 2) VESA is a trademark of the non-profit organization, Video Electronics Standard Association. 3) Macintosh is a trademark of Apple Computer Inc. 4) Windows® is a registered trademark of Microsoft Corporation in the United States and other countries.
Press the ¨ >/. button. The "BRIGHTNESS/CONTRAST" OSD appears.
BRIGHTNESS/CONTRAST 100 50
? . . . to move left / . . . to move right To erase the "CENTER" OSD, press the CENTER button again. The "CENTER" OSD automatically disappears 10 seconds after you release the buttons. To reset, press the RESET button while the OSD is on.
3 1 . 5 kHz/70Hz
Horizontal frequency Vertical frequency
2
Press the ¨ >/. buttons to adjust picture brightness.
. . . . for less brightness > . . . for more brightness The horizontal and vertical frequencies for each input signal received appear on the "BRIGHTNESS/CONTRAST" OSD.
The "BRIGHTNESS/CONTRAST" OSD disappears 3 seconds after you release the buttons.
4
To reset, press the RESET button while the OSD is on.
5
Adjustments Adjusting the Picture Size
The adjustment data becomes the individual setting for each input signal received.
2
Press the ¨ >/. buttons. > . . .to rotate clockwise . . . . to rotate counterclockwise
Setting the Color Temperature
The selected color temperature becomes the common setting for all input signals.
Resetting the Adjustment Data to Factory-preset Levels
To reset an adjustment item
Press the button of the adjustment item you want to reset, and then press the RESET button before the OSD (On Screen Display) disappears.
1
Press the SIZE button. The "SIZE" OSD appears.
SIZE
1
SIZE 32 68
Press the COLOR button. The "COLOR TEMPERATURE" OSD appears.
COLOR
To erase the "GEOMETRY" OSD, press the GEOM button again. The "GEOMETRY" OSD automatically disappears 10 seconds after you release the buttons. To reset, press the RESET button while the OSD is on.
COLOR TEMPERATURE VAR I ABLE 5000K 9300K 50
2
To reset all adjustment data at once (for the received signal)
Press the RESET button when no OSD is shown.
RESET
For vertical adjustment Press the ¨ >/. buttons.
2
Adjust with the > ?// and ¨ >/. buttons. To select 5000K or 9300K Press the > ?// buttons. The selected color temperature is indicated in yellow.
Adjusting the Pincushion
The adjustment data becomes the individual setting for each input signal received. > . . . to enlarge . . . . to diminish For horizontal adjustment Press the > ?// buttons.
1
Press the GEOM button. The "GEOMETRY" OSD appears.
GEOM
To reset all adjustment data to factorypreset levels
Press and hold the RESET button for more than 2 seconds. All adjustment data are reset to factory-preset levels.
RESET
GEOMETRY 32 68
? . . . to select 5000K / . . . to select 9300K To obtain the desired color temperature between 5000K and 9300K Press the ¨ >/. buttons.
--5--
? . . . to diminish / . . . to enlarge To erase the "SIZE" OSD, press the SIZE button again. The "SIZE" OSD automatically disappears 10 seconds after you release the buttons. To reset, press the RESET button while the OSD is on.
2
Press the > ?// buttons.
? . . . to diminish the picture sides
> . . . for higher temperature . . . . for lower temperature Your most recent adjusted color temperature will be recalled by pressing the ¨ >/. button. To erase the "COLOR TEMPERATURE" OSD, press the COLOR button again. The "COLOR TEMPERATURE" OSD automatically disappears 10 seconds after you release the buttons.
Adjusting the Picture Rotation
The adjustment data becomes the common setting for all input signals.
/ . . . to expand the picture sides
1
Press the GEOM button. The "GEOMETRY" OSD appears.
GEOM
To erase the "GEOMETRY" OSD, press the GEOM button again. The "GEOMETRY" OSD automatically disappears 10 seconds after you release the buttons.
GEOMETRY
To reset, press the RESET button while the OSD is on.
To reset, press the RESET button while the OSD is on.
32 68
CPD-100ES
6
7
CPD-100ES
Entering New Timings
When using a video mode that is not one of the factory preset modes, some fine tuning may be required to optimize the display to your preferences. Simply adjust the monitor according to the preceding adjustment instructions. The adjustments will be stored automatically and recalled whenever that mode is used. A total of 8 user-defined modes can be stored in memory. If the 9th mode is entered, it will replace the first.
Plug and Play
This monitor complies with DDCTM1 and DDC2B, which are the Display Data Channel (DDC) standards of VESA. When a DDC1 host system is connected, the monitor synchronizes with the V. CLK in accordance with the VESA standards and outputs the EDID (Extended Display Identification Data) to the data line. When a DDC2B host system is connected, the monitor automatically switches to the DDC2B communication. DDCTM is a trademark of the Video Electronics Standard Association.
Troubleshooting
This section may help you isolate a problem and as a result, eliminate the need to contact technical support, allowing continued productivity. No picture / If the u POWER indicator is not lit. -- Check that the power cord is properly connected. -- Check that the u POWER switch is in the "ON" position. / If the u POWER indicator is flashing in green and orange alternately. -- Check that your computer power switch is in the "ON" position. -- The monitor will recover when you press any key on the keyboard of the computer. -- Check that the video cable is properly connected. -- Ensure that no pins are bent or pushed in the HD15 connector of the cable. -- Check that the video card is seated completely in a proper bus slot. -- Check that the video sync signal is within that specified for the monitor. -- If using a Macintosh system, check that a proper HD15 - D15 adapter is provided to work correctly with your Macintosh. -- The monitor has a self-diagnose function. After disconnecting the video signal cable from the computer, turn on the u POWER switch of the monitor. Press and hold the "+" side of the > button for 2 seconds, then color bars will appear. The monitor is operating normally if the red, green, and blue color bars appear. Contact the maker of the computer to which the monitor is connected. / If the u POWER indicator is flashing. -- There is a potential monitor failure. Contact your dealer. If the message of "OUT OF SCAN RANGE" appears on the screen / Check that the video sync signal is specified for the monitor. Picture is scrambled / Check your graphics board manual for the proper monitor setting on your Multiscan 100ES/ 200ES. / Check this manual and confirm that the graphic mode and the frequency at which you are trying to operate is supported. Even within the proper range some video boards may have a sync pulse that is too narrow for the monitor to sync correctly. Color is not uniform / If the monitor is close to any potential sources of magnetic fields such as a speaker, or you turn the monitor while the u POWER switch is in the "ON" position, color may not be uniform. Trip the u POWER switch once to activate the Autodegauss cycle*. Picture is flickering / If the refresh rate is not appropriate, the picture may flicker. Set the refresh rate of the non-interlace mode as high as possible on the computer. For detailes on how to set the refresh rate, consult the dealer of your computer or Screen image is not centered or sized properly / Adjust the "CENTER," "SIZE," or "GEOMETRY" on the OSD (pages 5, 6). / Some video modes do not fill the screen to the edge of the monitor. There is no single answer to solve the problem. There is a tendency to have this problem on higher refresh timings and Macintosh video timings. Picture is fuzzy / Adjust the "CONTRAST" and "BRIGHTNESS" on the OSD (page 5). We have come across several brands of SVGA boards that have an excessive video output level which creates a fuzzy picture at max contrast. / Trip the u POWER switch once to activate the Auto-degauss cycle. Picture bounces or has wavy oscillations / Isolate and eliminate any potential sources of electric or magnetic fields. Common causes for this symptom are electric fans, fluorescent lighting, laser printers, and so on. / If you have another monitor close to this monitor, increase the distance between them to reduce the interference. / Try plugging the monitor into a different AC outlet, preferably on a different circuit. / Try the monitor on a completely different computer in a different room. Picture appears to be ghosting / Eliminate the use of video cable extension cables and/or video switch boxes if this symptom occurs. Excessive cable length or weak connections can produce this symptom. A fine horizontal line (wire) is visible / This wire stabilizes the vertically striped Aperture Grille (page 8). This Aperture Grille allows more light to pass through to the screen giving the Trinitron CRT more color and brightness. Wavy or elliptical (moire) pattern is visible / Due to the relationship between resolution, monitor AG pitch and the pitch of some image patterns, certain screen backgrounds, especially gray, sometimes show moire. This can only be eliminated by changing your desktop pattern. Just after turning the monitor on, a "boon" noise is heard / Just after turning the monitor on, a noise may be heard for about 3 seconds. This noise is not failure, it is caused by the Autodegauss cycle. The Auto-degauss function demagnetizes the metal frame of the CRT to obtain a neutral field for uniform color reproduction. If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. · If the problem persists, call your authorized Sony dealer from a location near your monitor. · Note the model name and the serial number of your monitor. Also note the make and name of your computer and video board.
Power Saving Function
This monitor meets the power saving guidelines set by the International ENERGY STAR Program as well as the more stringent TCO92 803299 (NUTEK) guidelines. It is capable of reduced power consumption when used with a computer equipped with Display Power Management Signaling (DPMS). By sensing the absence of the sync signal coming from the computer, it will reduce the power consumption as follows: CAUTION: The Power Saving function will automatically put the monitor into Active-off state if the power switch is turned on without any video signal input. Once the horizontal and vertical syncs are sensed, the monitor will automatically return to its Normal operation state.
Power consumption 110 W 15 W Required resumption time approx. 3 sec. approx. 3 sec. approx. 10 sec. u POWER indicator green on Orange and green flashes alternately Orange and green flashes alternately Orange on off
Use of the Tilt-Swivel
With the tilt-swivel, this unit can be adjusted to be viewed at your desired angle within 180° horizontally and 20° vertically. To turn the unit vertically and horizontally, hold it at its bottom with both hands.
15° 90°
--6--
90° 5°
State 1 2 Normal operation Stand-by (1st step of power saving) Suspend (2nd step of power saving) Active-off (3rd step of power saving) Power-off
3
15 W
Damper Wire
Using a white background, very thin horizontal stripes on the screen are visible as shown on the illustration. These stripes are damper wires. These wires are attached to the aperture grille inside the Trinitron tube and are there to dampen vibrations of the aperture grille in order to prevent them from influencing the picture quality.
Damper wire Approx. 6 cm (CPD-200ES/ 200EST only)
4 5
8W 0W
Approx. 6 cm
8
10
video board.
CPD-100ES
SECTION 2 DISASSEMBLY
2-1. CABINET REMOVAL
2-2. SERVICE POSITION
3 Cabinet
2 Screw cover
A board
1
3
2 Screw cover
D board
1 Four screws
2
(BVTP 4 x 16)
2-3. D BOARD REMOVAL
1 A board
6 Five screws
(BVTP 3 x 12)
2 One screw
(BVTT 4 x 8)
3 Cable stopper 4 Two screws
(BVTP 3 x 12)
5 Cable bracket
7 D board
--7--
CPD-100ES
2-4. PICTURE TUBE REMOVAL
9 Demagnetization coil
3 Two screws 10 Tension spring
(BVTP 4 x 16)
2 A board
5 Neck assy
6 Deflection yoke
Two degaussing 12 Tow degaussing coil holders coil holders
8 Picture tube 7 Four screws
(Tapping screw 5)
4 Stand assy
(D board)
1 Anode cap
Two degaussing 11 Tow degaussing
coil holders
Cushion
· REMOVAL OF THE ANODE-CAP
NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after removing the anode.
· REMOVAL PROCEDURES
Turn up one side of the rubber cap in the direction indicated by arrow .
Use your thumb to pull the rubber cap firmly in the direction indicated by arrow .
When one side of the rubber cap separates from the anode button, the anodecap can be removed by turning the rubber cap and pulling it in the direction of arrow .
· HOW TO HANDLE AN ANODE-CAP
Do not use sharp objects which may cause damage to the surface of the anode-cap. Do not squeeze the rubber covering too hard to avoid damaging the anode-cap. A material fitting called a shatter-hook terminal is built into the rubber. Do not force turn the foot of the rubber cover. This may cause the shatter-hook terminal to protrude and damage the rubber.
--8--
CPD-100ES
SECTION 3 SAFETY RELATED ADJUSTMENT
When replacing parts shown in the table below, the following operational checks must be performed as a safety precaution against X-rays emissions from the unit.
D - BOARD Part Replaced ([)
RV501
b) HV Hold-Down Check 1) Using an external DC Power supply, apply the voltage shown below between cathode of D511 on "D" Board and GND, and confirm that the HV Hold-Down circuit works. (Raster disappears) Standard voltage: 35.20 + 0.05 VDC Check Condition · Input voltage : 120 + 2 VAC · Input signal : Any pattern (fH = 64 kHz) · Controls : CONT and BRT 2 Minimum : Screen VR (G2)2 Cutoff
Part Replaced (])
IC801, IC901, IC904, FBT (T501) D511, R532, R533, R534, R535, R538, R539, R542, R543, R544, R545, R807, R822, R939, R996, RV501, C509, C515, C516, C528, C542, C548, C549, C802, C814, C910 D515, R540, R823, C517, C815, D596, R541, R824, C519, C904,
Allow the unit to warm up for one minute prior to checking the following conditions.
c) Beam Protector Check (Software logic) 1) Using an external DC power supply, apply the voltage 7.00 + 0.05 VDC between pin 11 of FBT (T501) and GND, and confirm that the voltage of both ends C519 is with in the voltage range shown below. Standard voltage: Less than 3.26 VDC Check Condition · Input voltage : 120 + 2 VAC · Input signal : Any pattern (fH = 64 kHz) · Controls : CONT and BRT 2 Minimum : Screen VR (G2) 2 Cutoff
a) HV Regulator Check
Input white cross hatch signal. (fH = 64 kHz) Minimum CONT and BRT controls. Cut off Screen VR (G2). Input voltage: 120 + 2 VAC Confirm that the voltage is within the voltage range shown below. Standard voltage: 25.0KV + 0.5KV 6) When replacing components identified by ], make sure to recheck the High Voltage. 7) Verify the High Voltage as shown above (25.0KV + 0.5KV) is within specification. If not, set H. SIZE data at minimum (-127) and then adjust RV501 on "D" Board. 8) After adjusting the High Voltage within specification, put the RV cover on RV501 as shown below and apply sufficient amount of RTV around RV501. 1) 2) 3) 4) 5)
d) +B MAX. Check 1) Input white cross hatch (fH = 64 kHz) signal. 2) Minimum CONT and BRT controls. 3) Input voltage: 120 + 2 VAC Note: Use NF power supply or make sure that distortion factor is 3% or less. 4) Confirm that the voltage is within the voltage range shown below. Standard voltage: 143 + 2 VDC
10
RV501
4
--9--
CPD-100ES
SECTION 4 ADJUSTMENTS
Connect the communication cable of the connector located on the D board on the monitor. Run the service software and then follow the instructions.
1 1-690-391-21
2 A-1500-819-A Interface Unit
3 3-702-691-01 Connector Attachment
IBM AT Computer as a Jig
To BUS CONNECTOR
D-sub (9 Pin [female])
mini Din (8Pin)
4 Pin
4 Pin
4 Pin
*The parts above ( 1 ~ 3 ) are necessary for DAS adjustment.
Allow a 30 minute warm-up period prior to making the following adjustments. Landing Rough Adjustment Enter the full white signal. Adjust the contrast to the maximum. Make the screen monogreen. Reverse the DY, and adjust coarsely the purity magnet so that a green raster positions in the center of screen. 5. Moving the DY forward, adjust so that an entire screen becomes monogreen. 6. Adjust the tilt of DY, and fix lightly with a clamp. 1. 2. 3. 4. Landing Fine Adjustment Place the set in the Helmholtz coil. Enter a green signal only. Degauss the entire screen with hand-degausser. Attach a wobbling coil to the specified position of CRT neck. 5. Attach a landing adjuster sensor on the CRT. 6. Using a landing checker, adjust the DY position, purity, tilt of DY. 7. Clamp the DY screw. Clamping torque: 22 + 2 kgcm (2.2+ 0.2 N.m) · Convergence Rough Adjustment 1. Enter the white crosshatch signal. 2. Adjust roughly the horizontal and vertical convergence at four-pole magnet. 3. Adjust roughly HMC and VMC at six-pole magnet. · 1. 2. 3. 4. Convergence Fine Adjustment Set DY four-pole magnet to mechanical center before adjustment. Set the This should be prime mode. finger
Mechanical Center
NECK Assy 6-pole Mg P.S Mg
XBV
DY
CRT
4-pole Mg
1. 2
Receive R.B. cross-hatch. Adjust H.STAT and V.STAT at four-pole magnet.
< 4 Pole Magnet>
2
1
1
R B R
1 + 2 R B
2 B
2
1
R B
1 + 2 R
1
B 2 RB
-- 10 --
CPD-100ES
3. 4. Receive White cross-hatch. Adjust HMC and VMC at six-pole magnet. < 6 Pole Magnet>
2 1
Purity 4-Pole Mg 6-Pole Mg
G
2
G
1
DY XBV
Dot adjustment
5. 6.
Receive R.B. cross-hatch. Adjust XBV at DY four-pole magnet. XBV Correction
R
a When
B
Less than 10 mm
Vertical and Horizontal Position and Size Specification
a
1) Open DY four-pole. (Do not move H.STAT) 2) Re-adjust V.STAT with four-pole at NECK Ass'y.
A
a < 2.5mm b < 2.5mm
a
b When
R B
A 202
B b b
B 270
Less than 10 mm
1) Close DY four-pole. (Do not move H.STAT) 2) Re-adjust V.STAT with four-pole at NECK Ass'y. 7. 8. 9. Repeat the above procedure so that R.G.B. will on X, Y axis. Adjust H.TILT by swinging the DY neck right and left. Adjust XCV with XCV core. XCV movement
B
Convergence Specification
B A A B 0.24mm 0.30mm 0.30mm 0.35mm
R
10.
Adjust V.TILT with TLV VR. TLV movement
R B R B
R B B
Focus adjustment Adjust focus (V) and focus (H) for optimum focus.
A-BOARD
R
11.
Adjust Y.CROSS with YCH VR. YCH movement
Focus (H)
R B
12.
Paint lock the four-pole and six-pole Mg.
XCV
Focus (V)
YCH TLV
FBT
-- 11 --
CPD-100ES
5-2. CIRCUIT BOARDS LOCATION
A
D
5-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
Note: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytic. · Indication of resistance, which does not have one for rating electrical power, is as follows. Pitch: 5 mm Rating electrical power 1/4 W (CHIP: 1/10 W) · All resistors are in ohms. · f : nonflammable resistor. · F : fusible resistor. · : internal component. · p : panel designation and adjustment for repair. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · When replacing parts shown in the table below, be sure to perform the safety related adjustment.
D - BOARD Part Replaced ([)
RV501
Part Replaced (])
IC801, IC901, IC904, FBT (T501) D511, D515, D596, R532, R533, R534, R535, R538, R539, R540, R541, R542, R543, R544, R545, R807, R822, R823, R824, R939, R996, RV501, C509, C515, C516, C517, C519, C528, C542, C548, C549, C802, C814, C815, C904, C910
· ·
· The components identified by [ in this basic schematic diagram have been carefully factory-selected for each set in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used. · When replacing components identified by ], make the necessary adjustments by using RV501 ([) as indicated. (See page 9)
e E
: earth-ground. : earth-chassis.
· · · · · · · ·
Note: The components identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
All voltages are in Volts. Readings are taken with a 10 digital multimeter. Readings are taken with a color-bar signal input. Voltage variations may be noted due to normal production tolerances. * : Cannot be measured. Circled numbers are waveform references. : B +bus. : B - bus.
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
-- 18 -- -- 12 --
5-4. SEMICONDUCTORS
MTZJ-T-77-4.7B MTZJ-T-77-5.6B MTZJ-T-77-8.2B RB441QT-77 RD27ES-T1B2 MTZJ-T-77-10B MTZJ-T-77-18 RD4.7ES-T1B2 RD5.6ES-T1B2 1SS119-25TD
EGP20DPKG23 EGP10GPKG23 1SS133T-77
CATHODE
CATHODE
UF3ML-6505 RGP02-20EL-6394 3DL41A (LC6-15) HSS 82
2SC5022-02
EGP30D 2SA1037K-T-146-QR
TDA6103Q
SB340L-6489
5TUZ52
CATHODE
CATHODE
C B E
ANODE
9 12 8 7
36 4
5
54 6
ANODE
B
ANODE
3
C
72 8
CATHODE
9
E
1
ANODE
ANODE
LM1281
SN74HCT02AN
SNY425
TDA9105S
VPC5023CS-095
ST7272N5B1/CKO
MC 44603P
TL 431CLP
28
15
14
8
24
13
42
22
22
12
16
56 29
9
1
14
1
7
1
12
1
21
1
28
1
11
1
8
NJM4558D
GP104005-E-G23
GBU4JL-6088
TDA 8172
UF4007G23
2SD2394-F
LA 6500-FA
8
CATHODE
7
{
CATHODE
` `
|
SEL1422G-C SG232D-658 SEL1922D-C SY432W-M-658
1
6 2 3 4
8 7
{
5
ANODE
` ` |
1 7
B
ANODE
1
C E
5
ANODE
CATHODE
6
2SC3941A-Q2 (TA)
1
5
2SA1048TP-VGR 2SC3311A-QRSTA 2SA1309A-QRSTA
LETTER SIDE
3
2SC3209-TK
2SC2001TP-K2
4
2SB1375 2SB1565F
2SC5129
LM2406T
PST600D-T
B
1 1
Vcc
11
14
E C B
E C B
E C B
E C B
B
C E
C E
GND
OUT
IRFIBC40G-LF38
2SD1640Q
M0C8105TV
IRFI9630
DTC124ES-TP
2SK1904
2SK2562-01-F165
6
1 i `2 j i { j 3 i ` j
5 12 3
6
4
5
or 12 B C 3
E
G
D
S
1 i `2 j i | j 3 i ` j
4
G G D SD S
1
2
E
3
C
G
D
D S
B
G
S
CPD-100ES
SECTION 6 EXPLODED VIEWS
· Items with no part number and no description are not stocked because they are PART NO. required for routine REF.NO. seldom DESCRIPTION service. · The component parts of an assembly are indicated by the reference numbers in the remarks column. · Items marked " * " are not stocked since they are seldom required for routine service. Some delay REF.NO. PART NO. should be REMARK anticipated when ordering these items. The components Identified by shading and mark ˇ a re critical for safety. Replace only with part number REMARK specified. DESCRIPTION
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
6-1. CHASSIS
r 7-685-648-79 ˘ 7-685-663-71 SCREW +BVTP 3X12 SCREW +BVTP 4X16
16 15 14 13
33
32 7 34 35 4 6 7 10
17 25 12 23 24 26 27 28 29 30 31
5 8 9 19 18 4 3 2 36
REF.NO. 1 2 3 4 5 5 * PART NO. X-4034-789-1 4-060-162-01 4-060-157-01 4-045-123-01 8-734-827-05 8-734-829-05 4-365-808-01 4-060-166-01 8-451-469-21 1-500-386-11 1-452-756-11 A-1298-209-A 4-060-175-01 4-060-153-01 4-060-184-01 1-409-799-11 DESCRIPTION BEZEL ASSY SPRING, COMPRESSION BUTTON, POWER HOLDER, DEGAUSSING COIL CRT 15FR2 (M36LDJ15X) (EQ) CRT 15FR2 (M36LDJ15X) (SH) SCREW (5), TAPPING SPACER, DY DY Y15FRF2M2 FILTER CLAMP (FERRITE CORE) NECK ASSY (NA293) A BOARD, COMPLETE CUSHION (A) LABEL, X-RAY SPRING, TENSION COIL, DEMAGNETIZATION REMARK 2-3
11 21 20
22
1
REF.NO. 19 ˇ 20 21 22 23 * 24 * 25 26 * 27 * 28 29 30 31 32 33 * * * *
PART NO. X-4033-083-1 1-543-653-11 4-389-025-01 7-685-659-71 4-060-151-01 4-060-150-01 1-776-975-11 4-060-177-01 4-060-178-01 4-060-183-01 4-060-179-01 4-060-180-01 X-4034-791-1 4-060-155-01 4-060-154-01
DESCRIPTION
REMARK
ˇ ˇ
TRANSFORMER ASSY, FLYBACK (NX-4130//J1E) CORE ASSY, BEAD (DIVISION TYPE) SCREW (M4x8)(EXT.TOOTHWASHER) SCREW + BVTT 4x8 (S) STOPPER, CABLE BRACKET, CABLE CABLE ASSY (15P D-SUB) COVER, BOTTOM HOLDER, STAND STOPPER (A), STAND SLIDER RING, TILT SWIVEL STAND BASE, ASSY HOLDER, HV CABLE LABEL, INFORMATION
6 7 8 ˇ 9 10 ˇ 11 12 13 14 15 * * *
ˇ
16 17 18 *
4-060-149-01 CABINET 4-060-165-01 COVER, SCREW A-1346-652-A D BOARD, COMPLETE
34 35 * 36 *
1-452-032-00 MAGNET, DISC X-4034-792-1 PERMALLOY ASSY, STAND 4-060-152-01 LABEL, ENERGY STAR
-- 29 --
CPD-100ES
REF.NO.
6-2. PACKING MATERIALS
PART NO. DESCRIPTION
REMARK
REF.NO.
PART NO.
DESCRIPTION
REMARK
53 52
51 54
55
56
REF.NO. 51 52 * 53 ˇ 53 ˇ
PART NO. 3-860-654-01 4-060-187-01 1-765-717-11 1-558-481-11
DESCRIPTION
REMARK
MANUAL, INSTRUCTION CUSHION (TOP) ASSY. CORD SET, POWER (EQ) CORD SET, POWER (SH) BAG, POLYETHYLENE CUSHION (BOTTOM) ASSY. INDIVIDUAL CARTON
54 * 4-060-194-01 55 * 4-060-192-01 56 * 4-060-871-01
-- 30 --
CPD-100ES
SECTION 7 ELECTRICAL PARTS LIST
Note:
The REF.NO. components Identified by shading PART NO. DESCRIPTION and mark ˇ a re critical for safety. Replace only with part number specified.
The components identified by [ in this manual have been carefully factory-selected for each set in order REMARK to satisfy regulations regarding XREF.NO. PART NO. ray radiation. Should replacement be required, replace only with the value originally used. · Items marked " " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
A
RESISTORS
· All resistors are in ohms DESCRIPTIONnonflammable REMARK · F:
CAPACITORS INDUCTORS
*
·
MF = µF
Note:
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
UH = µH MMH = MH
When indicating parts by reference number, please include the board name.
· All variable and adjustable resistors have characteristic curve B, unless otherwise noted.
REF.NO.
PART NO.
DESCRIPTION
REMARK
REF.NO. C035 C036 C040 C041 C050 C055 C088 C092 C093 C100 C101 C103 C104 C105 C106 C107 C201 C202 C203 C204 C205 C206 C207 C301 C302 C303 C304 C305 C306 C307 C330 C334 C351
PART NO. 1-115-349-51 1-163-231-11 1-164-004-11 1-164-004-11 1-164-004-11 1-163-231-11 1-126-934-11 1-164-004-11 1-104-396-11 1-104-664-11 1-126-960-11 1-164-004-11 1-107-823-11 1-164-004-11 1-137-528-11 1-164-346-11 1-126-960-11 1-164-004-11 1-164-004-11 1-107-823-11 1-164-004-11 1-137-528-11 1-164-346-11 1-126-960-11 1-164-004-11 1-164-004-11 1-107-823-11 1-164-004-11 1-137-528-11 1-164-346-11
DESCRIPTION CERAMIC CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM CERAMIC CHIP 0.01MF 15PF 0.1MF 0.1MF 0.1MF 15PF 220MF 0.1MF 10MF 47MF 1MF 0.1MF 0.47MF 0.1MF 0.1MF 1MF 1MF 0.1MF 0.1MF 0.47MF 0.1MF 0.1MF 1MF 1MF 0.1MF 0.1MF 0.47MF 0.1MF 0.1MF 1MF 4.7MF 0.1MF 0.1MF
REMARK 2KV 50V 25V 25V 25V 50V 16V 25V 16V 25V 50V 25V 16V 25V 250V 16V 50V 25V 25V 16V
A
* A-1298-209-A A BOARD, COMPLETE
4-382-854-01 SCREW (M3X8), P, SW (+)
5% 10% 10% 10% 5% 20% 10% 20% 20% 20% 10% 10% 10% 10%
CAPACITOR
C001 C002 C003 C004 C005 C006 C007 C008 C009 C010 C011 C012 C013 C014 C015 C016 C017 C018 C019 C020 C022 C023 C024 C025 C026 C027 C028 C029 C030 C031 1-136-169-00 1-137-528-11 1-137-528-11 1-164-004-11 1-163-263-11 1-126-933-11 1-104-664-11 1-164-004-11 1-164-004-11 1-164-004-11 1-128-562-11 1-164-004-11 1-126-933-11 1-106-220-00 1-164-004-11 1-126-933-11 1-104-664-11 1-107-652-11 1-164-004-11 1-163-227-11 1-164-346-11 1-163-275-11 1-163-263-11 1-163-251-11 1-163-251-11 1-164-346-11 1-104-664-11 1-107-823-11 1-164-489-11 1-162-318-11 FILM FILM FILM CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT MYLAR CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC 0.22MF 0.1MF 0.1MF 0.1MF 330PF 100MF 47MF 0.1MF 0.1MF 0.1MF 47MF 0.1MF 100MF 0.1MF 0.1MF 100MF 47MF 10MF 0.1MF 10PF 1MF 0.001MF 330PF 100PF 100PF 1MF 47MF 0.47MF 0.22MF 0.001MF 5% 10% 10% 10% 5% 20% 20% 10% 10% 10% 20% 10% 20% 10% 10% 20% 20% 20% 10% 0.5PF 50V 250V 250V 25V 50V 16V 25V 25V 25V 25V 100V 25V 16V 100V 25V 16V 25V 200V 25V 50V 16V 50V 50V 50V 50V 16V 25V 16V 16V 500V
20% 10% 10% 10%
10% 25V 10% 250V 16V 20% 50V 10% 25V 10% 10% 10% 10% 25V 16V 25V 250V 16V
5% 5% 5% 5%
1-126-963-11 ELECT 1-164-004-11 CERAMIC CHIP 1-137-528-11 FILM
20% 50V 10% 25V 10% 250V
20% 10% 10% 10%
CONNECTOR
CN301 CN302 1-506-108-41 PIN, CONNECTOR (TERMINAL PIN) 1-695-915-11 TAB (CONTACT)
-- 31 --
CPD-100ES
A
REF.NO. CN303 CN305 CN306 * CN307 * CN308 PART NO. 1-695-915-11 1-564-513-11 1-564-510-11 1-564-512-11 1-695-915-11
Note:
The components Identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
Note:
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
DESCRIPTION TAB (CONTACT) PLUG, CONNECTOR 10P PLUG, CONNECTOR 7P PLUG, CONNECTOR 9P TAB (CONTACT)
REMARK
REF.NO.
PART NO.
DESCRIPTION
REMARK
FILTER
FL001 FL101 ˇ FL201 ˇ FL301 ˇ 1-421-995-11 1-414-793-21 1-414-793-21 1-414-793-21 FILTER, NOISE INDUCTOR INDUCTOR INDUCTOR
CN309 1-564-511-11 PLUG, CONNECTOR 8P CN310 * 1-564-507-11 PLUG, CONNECTOR 4P CN311 * 1-564-507-11 PLUG, CONNECTOR 4P
IC
IC001 IC002 IC003 IC004 IC005 8-759-366-36 8-759-399-84 8-759-399-76 8-759-434-40 8-759-634-51 IC LM1281 IC LM2406T IC SNY425 IC TDA6103Q/N3,112 IC M5218AP
DIODE
D002 D014 D016 D017 D101 D102 D104 D105 D106 D201 D202 D204 D205 D206 D301 D302 D304 D305 D306 8-719-911-19 8-719-911-19 8-719-109-89 8-719-109-89 8-719-911-19 8-719-911-19 8-719-970-83 8-719-970-83 8-719-970-83 8-719-911-19 8-719-911-19 8-719-970-83 8-719-970-83 8-719-970-83 8-719-911-19 8-719-911-19 8-719-970-83 8-719-970-83 8-719-970-83 DIODE 1SS119-25 DIODE 1SS119-25 DIODE RD5.6ESB2 DIODE RD5.6ESB2 DIODE 1SS119-25 DIODE 1SS119-25 DIODE HSS82 DIODE HSS82 DIODE HSS82 DIODE 1SS119-25 DIODE 1SS119-25 DIODE HSS82 DIODE HSS82 DIODE HSS82 DIODE 1SS119-25 DIODE 1SS119-25 DIODE HSS82 DIODE HSS82 DIODE HSS82
JACK
J001 ˇ 1-251-335-11 SOCKET, CRT
COIL
L001 L101 L201 L301 1-412-537-31 1-407-500-00 1-407-500-00 1-407-500-00 INDUCTOR INDUCTOR INDUCTOR INDUCTOR 10 4.7MMH 4.7MMH 4.7MMH
TRANSISTOR
Q001 Q002 Q003 Q004 Q005 Q006 8-729-032-61 8-729-216-22 8-729-216-22 8-729-120-28 8-729-216-22 8-729-216-22 TRANSISTOR 2SC5022-02 TRANSISTOR 2SA1162-G TRANSISTOR 2SA1162-G TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1162-G TRANSISTOR 2SA1162-G
FERRITE BEAD RESISTOR
FB001 FB002 FB003 FB004 FB005 FB006 FB007 FB008 FB009 FB010 FB011 FB012 FB101 ˇ FB110 FB201 ˇ 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-500-104-21 1-412-911-11 1-500-104-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR R001 R002 R003 R004 R005 R006 R007 R008 R010 R011 R012 R013 R014 R015 R016 R017 R018 1-216-049-91 1-216-661-11 1-216-101-00 1-216-085-00 1-216-049-91 1-216-025-91 1-216-049-91 1-216-025-91 1-216-049-91 1-216-091-00 1-216-109-00 1-216-675-11 1-216-025-91 1-216-053-00 1-216-073-00 METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE 1K 2.7K 150K 33K 1K 100 1K 100 1K 56K 330K 10K 100 1.5K 10K 100 100 5% 1/10W 0.50% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W
5% 1/10W 0.50% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 5% 1/10W 1/10W
FB210 1-412-911-11 INDUCTOR FB301 ˇ 1-500-104-21 INDUCTOR FB310 1-412-911-11 INDUCTOR
1-216-025-91 METAL GLAZE 1-216-025-91 METAL GLAZE
-- 32 --
CPD-100ES
Note:
The components Identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
Note:
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
AD
REMARK 390 100 1K 75 47 100K 100 10K 10K 4.7K 1M 220K 390 100 1K 5% 1/4W 20% 1/2W 5% 1/10W 0.50% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 0.50% 1/10W 5% 1% 5% 20% 5% 1/10W 1/4W 1/4W 1/2W 1/10W
REF.NO. R019 R020 R021 R022 R024 R025 R026 R027 R028 R029 R030 R031 R032 R033 R035 R036 R039 R040 R045 R048 R049 R053 R057 R058 R064 R077 R097 R098 R101 R102 R103 R104 R106 R107 R108 R109 R110 R111 R151 R162 R201 R202 R203 R204 R206 R207 R208 R209 R210
PART NO. 1-216-025-91 1-216-025-91 1-216-025-91 1-216-049-91 1-216-065-00 1-216-065-00 1-216-073-00 1-218-756-11 1-216-372-11 1-216-099-00 1-216-097-91 1-216-049-91 1-216-665-11 1-216-679-11 1-216-017-91 1-216-017-91 1-218-764-11 1-216-121-91 1-216-057-00 1-211-885-21 1-216-099-00 1-219-621-91 1-216-057-00 1-216-041-00 1-202-830-00 1-216-047-91 1-216-295-91 1-216-295-91 1-216-624-11 1-216-017-91 1-216-675-11 1-216-025-91 1-216-073-00 1-216-073-00 1-216-667-11 1-216-121-91 1-215-477-00 1-249-412-11 1-202-549-00 1-216-049-91 1-216-624-11 1-216-017-91 1-216-097-91 1-216-041-00 1-216-073-00 1-216-073-00 1-216-667-11 1-216-121-91 1-215-477-00
DESCRIPTION METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL CHIP METAL OXIDE METAL GLAZE METAL GLAZE METAL GLAZE METAL CHIP METAL CHIP METAL GLAZE METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL METAL GLAZE METAL METAL GLAZE METAL GLAZE SOLID METAL GLAZE SHORT SHORT METAL CHIP METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE METAL CHIP METAL GLAZE METAL CARBON SOLID METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL CHIP METAL GLAZE METAL 100 100 100 1K 4.7K 4.7K 10K 150K 1.8 120K 100K 1K 3.9K 15K 47 47 330K 1M 2.2K 2.2M 120K 22M 2.2K 470 10K 820 0 0 75 47 10K 100 10K 10K 4.7K 1M 220K 390 100 1K 75 47 100K 470 10K 10K 4.7K 1M 220K
REMARK 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W
REF.NO. R211 R251 R262 R301 R302 R303 R304 R306 R307 R308 R309 R310 R311 R351 R362
PART NO. 1-249-412-11 1-202-549-00 1-216-049-91 1-216-624-11 1-216-017-91 1-216-097-91 1-216-025-91 1-216-073-00 1-216-073-00 1-216-667-11 1-216-121-91 1-215-477-00 1-249-412-11 1-202-549-00 1-216-049-91
DESCRIPTION CARBON SOLID METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL GLAZE METAL CHIP METAL GLAZE METAL CARBON SOLID METAL GLAZE
5% 1/10W 5% 1/10W 0.50% 1/10W 5% 2W F 5% 1/10W 5% 1/10W 5% 1/10W 0.50% 1/10W 0.50% 1/10W 5% 1/10W 5% 1/10W 0.50% 1/10W 5% 1/10W 5% 1/10W 5% 1W 5% 10% 5% 5% 20% 5% 1/10W 1/4W 1/10W 1/10W 1/2W 1/10W
SPARK GAP
SG001 ˇ SG101 ˇ SG201 ˇ SG301 ˇ 1-519-422-11 1-519-504-11 1-519-504-11 1-519-504-11 GAP, SPARK GAP, DISCHARGE GAP, DISCHARGE GAP, DISCHARGE
CRYSTAL
X1 1-567-890-11 VIBRATOR, CRYSTAL
D
* A-1346-652-A D BOARD, COMPLETE
1-533-223-11 1-900-214-27 1-900-801-67 4-045-132-01 HOLDER, FUSE LEAD ASSY, FOCUS CONNECTOR ASSY HOLDER (A), LED
0.50% 1/10W 5% 1/10W 0.50% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 0.50% 1/10W 5% 1% 5% 20% 5% 1/10W 1/4W 1/4W 1/2W 1/10W C401 C402 C403 C404 C405 C406 C410 C420 C500
*
4-382-854-11 SCREW (M3X10), P, SW (+) 4-389-025-01 SCREW (M4) (EXT TOOTH WASHER)
CAPACITOR
1-128-528-11 1-106-228-00 1-137-399-11 1-107-894-11 1-101-006-00 1-137-375-11 1-107-914-11 1-137-368-11 1-136-169-00 ELECT MYLAR FILM ELECT CERAMIC FILM ELECT FILM FILM 470MF 0.22MF 0.1MF 220MF 0.047MF 0.068MF 1000MF 0.0047MF 0.22MF 20% 10% 5% 20% 25V 100V 50V 35V 50V 50V 25V 50V 50V
0.50% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 0.50% 1/10W 5% 1/10W 1% 1/4W
5% 20% 5% 5%
-- 33 --
CPD-100ES
D
REF.NO. C502 C503 C505 C506 C507 C508 C509 C511 C512 C513 C514 C515 C516 C517 C518 C519 C520 C521 C523 C527 C528 C532 C533 C534 C535 C540 ˇ C541 ˇ C542 C544 C547 C548 C549 C550 C562 C565 C566 C567 C568 C569 C570 C576 C582 C583 C593 C598 C599 C601 C602 ˇ C603 ˇ PART NO. 1-137-370-11 1-107-667-11 1-126-964-11 1-137-370-11 1-162-318-11 1-109-878-11 1-136-169-00 1-101-810-00 1-137-399-11 1-106-383-00 1-126-941-11 1-136-203-11 1-126-960-11 1-137-370-11 1-102-002-00 1-126-963-11 1-107-955-11 1-126-960-11 1-106-375-12 1-162-117-00 1-126-965-11 1-106-367-00 1-164-735-11 1-115-349-51 1-161-754-00 1-136-064-00 1-113-576-11 1-137-368-11 1-115-349-51 1-126-941-11 1-137-425-11 1-137-399-11 1-117-206-21 1-115-511-11 1-136-169-00 1-137-370-11 1-137-370-11 1-137-370-11 1-137-370-11 1-115-519-11 1-115-516-11 1-161-754-00 1-106-375-12 1-117-206-21 1-137-399-11 1-128-582-11 1-104-708-11 1-107-533-11 1-113-912-11
Note:
The components Identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
Note:
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
DESCRIPTION FILM ELECT ELECT FILM CERAMIC CERAMIC FILM CERAMIC FILM MYLAR ELECT FILM ELECT FILM CERAMIC ELECT ELECT ELECT MYLAR CERAMIC ELECT MYLAR CAPACITOR CERAMIC CERAMIC FILM FILM FILM CERAMIC ELECT FILM FILM FILM FILM FILM FILM FILM FILM FILM FILM FILM CERAMIC MYLAR FILM FILM ELECT FILM FILM CERAMIC 0.01MF 2.2MF 10MF 0.01MF 0.001MF 15PF 0.22MF 100PF 0.1MF 0.047MF 470MF 10000PF 1MF 0.01MF 680PF 4.7MF 100MF 1MF 0.022MF 100PF 22MF 0.01MF 0.0015MF 0.01MF 0.001MF 2200PF 0.0043MF 0.0047MF 0.01MF 470MF 0.33MF 0.1MF 0.36MF 0.12MF 0.22MF 0.01MF 0.01MF 0.01MF 0.01MF 0.56MF 0.33MF 0.001MF 0.022MF 0.36MF 0.1MF 10MF 0.47MF 1MF 0.0047MF
REMARK 5% 20% 20% 5% 10% 5% 5% 5% 5% 10% 20% 5% 20% 5% 10% 20% 20% 20% 10% 10% 50V 160V 50V 50V 500V 2KV 50V 500V 50V 200V 25V 630V 50V 50V 500V 50V 200V 50V 100V 500V
REF.NO. C604 ˇ C605 ˇ C606 ˇ C607 C608 C609 C610 C611 C612 C614 C615 C616 C617 C618 C619 C620 ˇ C621 C622 ˇ C628 C634 C635 C650 C651 C652 C653 C662 C675 C678 C802 C803 C804 C805 C806 C807 C808 C810 C811 C812 C813 C814 C815 C817 C818 C819 C820 C821 C822 C901 C902
PART NO. 1-113-912-11 1-113-896-11 1-113-896-11 1-137-368-11 1-107-894-11 1-137-399-11 1-102-115-00 1-136-177-00 1-137-370-11 1-102-973-00 1-137-364-11 1-113-912-11 1-106-343-00 1-107-884-11 1-137-366-11 1-109-984-11 1-136-203-11 1-113-912-11 1-137-399-11 1-126-941-11 1-126-935-11 1-125-700-11 1-107-933-11 1-107-914-11 1-126-941-11 1-126-941-11 1-137-364-11 1-162-115-00 1-102-116-00 1-102-106-00 1-137-364-11 1-126-965-11 1-126-767-11 1-137-399-11 1-137-364-11 1-124-768-11 1-137-399-11 1-137-365-11 1-137-370-11 1-136-169-00 1-137-367-11 1-126-933-11 1-137-399-11 1-136-173-00 1-137-366-11 1-102-112-00 1-137-368-11 1-137-399-11 1-137-368-11
DESCRIPTION CERAMIC CERAMIC CERAMIC FILM ELECT FILM CERAMIC FILM FILM CERAMIC FILM CERAMIC MYLAR ELECT FILM ELECT FILM CERAMIC FILM ELECT ELECT ELECT ELECT ELECT ELECT ELECT FILM CERAMIC CERAMIC CERAMIC FILM ELECT ELECT FILM FILM ELECT FILM FILM FILM FILM FILM ELECT FILM FILM FILM CERAMIC FILM FILM FILM 0.0047MF 220PF 220PF 0.0047MF 220MF 0.1MF 560PF 1MF 0.01MF 100PF 0.001MF 0.0047MF 0.001MF 1000MF 0.0022MF 390MF 10000PF 0.0047MF 0.1MF 470MF 470MF 220MF 100MF 1000MF 470MF 470MF 0.001MF 330PF 680PF 100PF 0.001MF 22MF 1000MF 0.1MF 0.001MF 4.7MF 0.1MF 0.0015MF 0.01MF 0.22MF 0.0033MF 100MF 0.1MF 0.47MF 0.0022MF 330PF 0.0047MF 0.1MF 0.0047MF
REMARK 20% 10% 10% 5% 20% 5% 10% 5% 5% 5% 5% 20% 10% 20% 5% 20% 5% 20% 5% 20% 20% 20% 20% 20% 20% 20% 5% 10% 10% 10% 5% 20% 20% 5% 5% 20% 5% 5% 5% 5% 5% 20% 5% 5% 5% 10% 5% 5% 5% 250V 250V 250V 50V 35V 50V 50V 50V 50V 50V 50V 250V 100V 16V 50V 400V 630V 250V 50V 25V 16V 200V 100V 25V 25V 25V 50V 2KV 50V 50V 50V 50V 16V 50V 50V 35V 50V 50V 50V 50V 50V 16V 50V 50V 50V 50V 50V 50V 50V
20% 50V 10% 200V 10% 500V 2KV 10% 2KV 2KV 2.5KV 50V 2KV 20% 25V 10% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 10% 10% 5% 5% 20% 20% 20% 20% 100V 50V 250V 250V 50V 50V 50V 50V 50V 250V 250V 2KV 100V 250V 50V 100V 250V 250V 250V 3% 3% 5%
-- 34 --
CPD-100ES
Note:
The components Identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
Note:
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
D
REMARK 330PF 330PF 0.22MF 10% 50V 10% 50V 5% 50V
REF.NO. C903 C904 C905 C906 C907 C908 C910 C911 C912 C913 C915 C916 C917 C918 C919 C920 C921 C923 C924 C925 C926 C927 C928 C929 C931 C932 C933 C934 C935 C937 C939 C940 C941 C942 C943 C944 C945 C946 C948 C950 C955 C960 C961 C962 C963 C967 C968 C969 C970
PART NO. 1-102-951-00 1-137-399-11 1-137-399-11 1-136-173-00 1-126-963-11 1-102-951-00 1-104-664-11 1-126-768-11 1-126-961-11 1-126-961-11 1-124-768-11 1-126-961-11 1-126-961-11 1-126-961-11 1-126-961-11 1-126-961-11 1-126-961-11 1-137-370-11 1-137-399-11 1-126-934-11 1-137-364-11 1-104-664-11 1-137-370-11 1-137-399-11 1-136-169-00 1-137-399-11 1-126-934-11 1-126-961-11 1-136-169-00 1-126-935-11 1-137-374-11 1-137-374-11 1-136-169-00 1-126-926-11 1-137-372-11 1-137-366-11 1-137-372-11 1-102-106-00 1-137-399-11 1-117-378-91 1-102-106-00 1-136-177-00 1-137-399-11 1-137-399-11 1-137-399-11 1-102-106-00 1-126-960-11 1-137-364-11 1-102-106-00
DESCRIPTION CERAMIC FILM FILM FILM ELECT CERAMIC ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT FILM FILM ELECT FILM ELECT FILM FILM FILM FILM ELECT ELECT FILM ELECT FILM FILM FILM ELECT FILM FILM FILM CERAMIC FILM FILM CERAMIC FILM FILM FILM FILM CERAMIC ELECT FILM CERAMIC 15PF 0.1MF 0.1MF 0.47MF 4.7MF 15PF 47MF 2200MF 2.2MF 2.2MF 4.7MF 2.2MF 2.2MF 2.2MF 2.2MF 2.2MF 2.2MF 0.01MF 0.1MF 220MF 0.001MF 47MF 0.01MF 0.1MF 0.22MF 0.1MF 220MF 2.2MF 0.22MF 470MF 0.047MF 0.047MF 0.22MF 1000MF 0.022MF 0.0022MF 0.022MF 100PF 0.1MF 1MF 100PF 1MF 0.1MF 0.1MF 0.1MF 100PF 1MF 0.001MF 100PF
REMARK 5% 5% 5% 5% 20% 5% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 5% 5% 20% 5% 20% 5% 5% 5% 5% 20% 20% 5% 20% 5% 5% 5% 20% 5% 5% 5% 10% 5% 5% 10% 5% 5% 5% 5% 10% 20% 5% 10% 50V 50V 50V 50V 50V 50V 25V 16V 50V 50V 35V 50V 50V 50V 50V 50V 50V 50V 50V 16V 50V 25V 50V 50V 50V 50V 16V 50V 50V 16V 50V 50V 50V 10V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V
REF.NO. C1801 C1802 C1803
PART NO.
DESCRIPTION
1-102-112-00 CERAMIC 1-102-112-00 CERAMIC 1-136-169-00 FILM
CONNECTOR
CN501 * CN503 * CN504 CN505 CN508 * CN509 * CN511 CN512 CN600 ˇ CN601 1-580-798-11 1-900-801-16 1-695-915-11 1-564-513-11 1-564-514-11 1-508-879-11 1-564-511-11 1-695-915-11 1-251-227-11 1-691-960-11 CONNECTOR PIN (DY) 6P CONNECTOR ASSY, 2P BOARD IN TAB (CONTACT) PLUG, CONNECTOR 10P PLUG, CONNECTOR 11P BASE POST PLUG, CONNECTOR 8P TAB (CONTACT) INLET, AC PIN, CONNECTOR (PC BOARD) 3P
CN605 * 1-506-371-00 PIN, CONNECTOR 2P CN610 1-695-915-11 TAB (CONTACT)
DIODE
D401 D402 D403 D501 D502 D503 D504 D505 D506 D508 D509 D510 D511 ˇ D515 D522 D526 D534 D544 D595 D596 D598 D601 ˇ D602 D603 D604 D605 D607 D608 D609 8-719-010-34 8-719-979-58 8-719-908-03 8-719-061-21 8-719-110-49 8-719-911-19 8-719-051-97 8-719-110-17 8-719-110-67 8-719-975-77 8-719-979-58 8-719-979-58 8-719-110-67 8-719-979-58 8-719-911-19 8-719-018-82 8-719-911-55 8-719-979-58 8-719-911-19 8-719-911-19 8-719-110-49 8-719-025-88 8-719-970-83 8-719-110-49 8-719-053-19 8-719-970-83 8-719-979-58 8-719-986-73 8-719-982-03 DIODE UZ-4.7BSC DIODE EGP10D DIODE GP08D DIODE FMQ-G5FMS DIODE RD18ESB2 DIODE 1SS119-25 DIODE 3DL41A(LC6-15) DIODE RD10ESB2 DIODE RD27ESB2 DIODE SB340 DIODE EGP10D DIODE EGP10D DIODE RD27ESB2 DIODE EGP10D DIODE 1SS119-25 DIODE RGP02-20EL-6394 DIODE U05G DIODE EGP10D DIODE 1SS119-25 DIODE 1SS119-25 DIODE RD18ESB2 DIODE GBU4JL-6088 DIODE HSS82 DIODE RD18ESB2 DIODE UF4007G23 DIODE HSS82 DIODE EGP10D DIODE RB441Q DIODE MTZJ-3.6A
-- 35 --
CPD-100ES
D
REF.NO. D650 D651 D652 D653 D654 D670 D801 D903 D906 D907 D908 D909 D910 D913 D915 D916 D917 D918 D920 D921 D922 D923 D924 D944 D945 D946 PART NO. 8-719-048-62 8-719-979-58 8-719-979-50 8-719-979-84 8-719-051-97 8-719-911-19 8-719-911-19 8-719-970-83 8-719-109-89 8-719-109-89 8-719-911-19 8-719-109-89 8-719-911-19 8-719-067-04 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-010-34 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19
Note:
The components Identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
Note:
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
DESCRIPTION DIODE UF3ML-6505 DIODE EGP10D DIODE EGP30D DIODE EGP20DPKG23 DIODE 3DL41A(LC6-15) DIODE 1SS119-25 DIODE 1SS119-25 DIODE HSS82 DIODE RD5.6ESB2 DIODE RD5.6ESB2 DIODE 1SS119-25 DIODE RD5.6ESB2 DIODE 1SS119-25 DIODE LT2463-23 DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25 DIODE UZ-4.7BSC DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25
REMARK
REF.NO. FB613 ˇ FB614 ˇ FB615 ˇ FB901 FB902 FB903 FB904 FB905
PART NO. 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11
DESCRIPTION INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR
REMARK
1-412-911-11 INDUCTOR 1-412-911-11 INDUCTOR 1-412-911-11 INDUCTOR
TERMINAL
GT001 * 1-537-738-21 TERMINAL, EARTH GT002 * 1-537-738-21 TERMINAL, EARTH
IC
IC400 IC401 IC601 ˇ IC603 ˇ IC604 ˇ IC652 ˇ IC801 ˇ IC901 IC902 ˇ IC903 IC904 ˇ 8-759-803-42 8-759-980-58 8-759-399-81 8-749-012-59 8-759-072-98 8-759-466-13 8-759-466-15 8-759-399-80 8-759-269-04 8-759-165-81 8-759-399-77 IC LA6500-FA IC TDA8172 IC MC44603P IC MOC8105TV IC TDA8138A IC TL431ACLPRP IC UPC6753 IC ST7272N5B1/CKO IC SN74HCT02AN IC PST600D-T IC TDA9105
COIL FUSE
F601 ˇ 1-576-231-11 FUSE (H.B.C.) 4A/250V L501 L504 L505 L506 L507 L513 L650 L651 L652 L653 L801 L900 1-412-550-11 1-459-104-00 1-412-531-31 1-459-104-00 1-412-531-31 1-409-896-11 1-412-537-31 1-412-537-31 1-406-665-11 1-412-537-31 INDUCTOR COIL, WITH CORE INDUCTOR COIL, WITH CORE INDUCTOR 1.2MMH 33UH 33UH
FERRITE BEAD
FB501 FB502 FB503 FB524 FB525 FB601 FB602 FB603 FB604 FB605 FB606 FB607 FB608 ˇ FB609 ˇ FB610 ˇ 1-410-396-41 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 0.45UH
COIL, HORIZONTAL LINEARITY INDUCTOR 10 INDUCTOR 10 COIL, CHOKE 10 INDUCTOR 10 10 10
1-410-645-31 INDUCTOR 1-410-645-31 INDUCTOR
FILTER
LF601 ˇ 1-429-180-11 TRANSFORMER, LINE FILTER
TRANSISTOR
Q500 Q501 8-729-031-89 TRANSISTOR 2SC3941A-Q(TA) 8-729-119-76 TRANSISTOR 2SA1175-HFE
FB611 ˇ 1-412-911-11 INDUCTOR FB612 ˇ 1-412-911-11 INDUCTOR
-- 36 --
CPD-100ES
Note:
The components Identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
Note:
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
D
REMARK 4.7 47 120K 10K 10K 470K 220K 1K 1K 47K 1K 4.7 1K 0.47 27 5.6K 0.47 270 68 100K 82 82 4.7 560K 82K 100K 8.2K 22 1K 200K 100K 1M 2.2K 2.2K 56K 47K 22 100 3.3K 10 10K 1.2K 2.2 2.2K 2.2K 0.47 2.2K 2.2K 5% 5% 5% 5% 5% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 1% 1% 5% 5% 1% 1% 1% 1% 1% 1% 1% 1% 5% 5% 1% 5% 5% 1% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/2W 1/4W F 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W 2W F F F F F
REF.NO. Q502 ˇ Q503 Q504 Q505 Q507
PART NO. 8-729-043-37 8-729-027-97 8-729-119-78 8-729-119-76 8-729-027-95
DESCRIPTION TRANSISTOR IRFU214 TRANSISTOR IRFI9630G-LF TRANSISTOR 2SC2785-HFE TRANSISTOR 2SA1175-HFE TRANSISTOR 2SC5129(LBSONY)
REMARK
REF.NO. R510 R511 R512 R513 R514 R515 R516 R517 R518 R519 R520 R521 R522 R523 R524 R525 R526 R527 R528 R529 R530 R531 R532 R533 ˇ R534 ˇ
PART NO. 1-249-389-11 1-249-401-11 1-247-881-00 1-249-429-11 1-249-429-11 1-215-485-00 1-219-683-11 1-249-417-11 1-249-417-11 1-249-437-11 1-249-417-11 1-249-389-11 1-249-417-11 1-249-377-11 1-216-447-00 1-249-426-11 1-249-377-11 1-216-477-11 1-215-910-00 1-249-441-11 1-216-474-11 1-216-474-11 1-249-389-11 1-215-487-00 1-215-467-00 1-215-469-00 1-249-428-11 1-249-397-11 1-215-421-00 1-215-476-00 1-215-469-00 1-215-493-00 1-215-429-00 1-215-429-00 1-215-463-00 1-215-461-00 1-249-397-11 1-247-807-31 1-215-433-00 1-215-880-00 1-249-429-11 1-215-423-00 1-249-385-11 1-249-421-11 1-249-421-11
DESCRIPTION CARBON CARBON CARBON CARBON CARBON METAL METAL CARBON CARBON CARBON CARBON CARBON CARBON CARBON METAL OXIDE CARBON CARBON METAL OXIDE METAL OXIDE CARBON METAL OXIDE METAL OXIDE CARBON METAL METAL METAL CARBON CARBON METAL METAL METAL METAL METAL METAL METAL METAL CARBON CARBON METAL METAL OXIDE CARBON METAL CARBON CARBON CARBON
Q508 ˇ 8-729-042-24 TRANSISTOR 2SB949-LE Q509 ˇ 8-729-042-33 TRANSISTOR 2SD1275Q-LE Q510 8-729-027-82 TRANSISTOR IRFPE40LF20 4-047-285-01 SHEET, INSULATING Q512 8-729-087-14 TRANSISTOR 2SK1904 Q513 Q514 Q515 Q528 Q529 Q602 Q654 Q655 Q656 ˇ Q670 Q901 Q902 Q903 8-729-027-14 8-729-027-14 8-729-140-50 8-729-140-50 8-729-028-34 8-729-926-79 8-729-141-83 8-729-119-78 8-729-119-78 8-729-142-46 8-729-119-78 TRANSISTOR 2SK1904 TRANSISTOR 2SK1904 TRANSISTOR 2SC3209LK TRANSISTOR 2SC3209LK TRANSISTOR 2SD1640Q,R TRANSISTOR IRFIBC40 TRANSISTOR 2SB1094-LK TRANSISTOR 2SC2785-HFE TRANSISTOR 2SC2785-HFE TRANSISTOR 2SC2001-LK TRANSISTOR 2SC2785-HFE
1/4W 1/4W F 3W F 3W F 1/4W 3W F 3W F 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W F 1/4W 1/4W 2W F 1/4W 1/4W 1/4W F 1/4W 1/4W
8-729-029-86 TRANSISTOR DTC124ESA 8-729-107-78 TRANSISTOR 2SC3623-K
RESISTOR
R401 R407 R408 R410 R411 R412 R418 R421 R422 R423 R424 R425 R426 R427 R500 R501 R503 R504 R505 R506 R507 R508 R509 1-249-425-11 1-215-447-00 1-249-383-11 1-215-859-00 1-215-445-00 1-215-421-00 1-214-798-21 1-214-800-11 1-215-866-11 1-215-439-00 1-215-447-00 1-215-439-00 1-249-383-11 1-215-447-00 1-249-405-11 1-247-863-91 1-249-437-11 1-215-888-00 1-247-863-91 1-216-392-11 CARBON METAL CARBON METAL OXIDE METAL METAL METAL METAL METAL OXIDE METAL METAL METAL CARBON METAL CARBON CARBON CARBON METAL OXIDE CARBON METAL OXIDE 4.7K 12K 1.5 22 10K 1K 1.8 2.2 330 5.6K 12K 5.6K 1.5 12K 100 22K 47K 220 22K 1.8 47K 1.8 4.7 5% 1% 5% 5% 1% 1% 1% 1% 5% 1% 1% 1% 5% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W F 1W F 1/4W 1/4W 1/2W 1/2W 1W F 1/4W 1/4W 1/4W 1/4W F 1/4W 1/4W F 1/4W 1/4W 2W F 1/4W 3W F 1/4W 3W F 1/4W F
R535 ˇ R536 R537 R538 R539 R540 R541 R542 ˇ R543 ˇ R544 ˇ R545 ˇ R546 R547 R548 R549 R550 R551 R552 R553 R554 R555 R563 R564
1-249-437-11 CARBON 1-216-392-11 METAL OXIDE 1-249-389-11 CARBON
1-249-377-11 CARBON 1-249-421-11 CARBON 1-249-421-11 CARBON
5% 1/4W F 5% 1/4W 5% 1/4W
-- 37 --
CPD-100ES
D
REF.NO. R567 R601 ˇ R602 ˇ R603 ˇ R604 R605 R606 R607 R608 R609 R610 R611 R612 R613 R614 R615 R619 R621 R623 R631 R651 R652 ˇ R654 ˇ R655 R656 R657 R658 R659 R660 R661 R662 R663 R664 R665 R666 R667 ˇ R670 R671 R672 R673 R674 R801 R807 R808 R809 R811 R815 R817 PART NO. 1-215-880-00 1-202-847-00 1-205-998-11 1-202-933-61 1-215-926-00 1-249-437-11 1-249-417-11 1-247-791-91 1-249-429-11 1-216-381-11 1-215-925-11 1-247-885-00 1-249-431-11 1-249-411-11 1-249-421-11 1-249-377-11 1-249-425-11 1-249-434-11 1-215-445-00 1-215-405-00 1-215-878-00 1-211-874-11 1-219-154-11 1-249-417-11 1-249-417-11 1-249-429-11 1-215-417-00 1-215-483-00 1-215-443-00 1-247-895-91 1-215-459-00 1-249-429-11 1-216-349-00 1-249-429-11 1-249-429-11 1-211-881-11 1-249-417-11 1-249-417-11 1-249-403-11 1-249-429-11 1-249-429-11 1-249-377-11 1-249-438-11 1-215-485-00 1-215-483-00
Note:
The components Identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
Note:
Les composants identifies per un trame et une marque ˇ sont critiques pout la securite. Ne les remplacer que par une piece portant le numero specifie.
DESCRIPTION METAL OXIDE SOLID WIREWOUND FUSIBLE METAL OXIDE CARBON CARBON CARBON CARBON METAL OXIDE METAL OXIDE CARBON CARBON CARBON CARBON CARBON CARBON CARBON METAL METAL METAL OXIDE FUSIBLE FUSIBLE CARBON CARBON CARBON METAL METAL METAL CARBON METAL CARBON METAL OXIDE CARBON CARBON FUSIBLE CARBON CARBON CARBON CARBON CARBON CARBON CARBON METAL METAL 10 560K 1 0.1 33K 47K 1K 22 10K 0.22 22K 180K 15K 330 2.2K 0.47 4.7K 27K 10K 220 33K 0.12 0.12 1K 1K 10K 680 390K 8.2K 470K 39K 10K 1 10K 10K 0.47 1K 1K 68 10K 10K 0.47 56K 470K 390K 18K 33K 47K
REMARK 5% 20% 5% 10% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 1% 5% 10% 10% 5% 5% 5% 1% 1% 1% 5% 1% 5% 5% 5% 5% 10% 5% 5% 5% 5% 5% 5% 5% 1% 1% 5% 1% 1% 2W F 1/2W 10W 1/2W F 3W F 1/4W 1/4W 1/4W 1/4W 3W F 3W F 1/4W 1/4W 1/4W 1/4W 1/4W F 1/4W 1/4W 1/4W 1/4W 1W F 1/2W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1W F 1/4W 1/4W 1/2W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W F 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W
REF.NO. R819 R820 R821 R822 R823 R824 R830 R831 R900 R901 R902 R903 R904 R905 R906 R907 R908 R909 R910 R911 R912 R915 R916 R917 R918 R919 R920 R921 R924 R925 R926 R927 R928 R929 R930 R931 R932 R933 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943
PART NO. 1-215-457-00 1-215-455-00 1-215-465-00 1-215-469-00 1-215-477-00 1-249-429-11 1-215-461-00 1-215-405-00 1-249-417-11 1-249-425-11 1-249-425-11 1-249-425-11 1-249-425-11 1-249-425-11 1-215-449-00 1-249-417-11 1-249-425-11 1-249-437-11 1-247-895-91 1-249-431-11 1-249-413-11 1-249-417-11 1-249-417-11 1-249-417-11 1-249-435-11 1-249-425-11 1-249-417-11 1-247-863-91 1-249-434-11 1-249-432-11 1-249-434-11 1-249-434-11 1-249-434-11 1-249-436-11 1-249-434-11 1-249-428-11 1-249-428-11 1-249-431-11 1-249-429-11 1-249-428-11 1-249-425-11 1-249-428-11 1-249-428-11 1-249-417-11 1-249-434-11
DESCRIPTION METAL METAL METAL METAL METAL CARBON METAL METAL CARBON CARBON CARBON CARBON CARBON CARBON METAL CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON 33K 27K 68K 100K 220K 10K 47K 220 1K 4.7K 4.7K 4.7K 4.7K 4.7K 15K 1K 4.7K 47K 470K 15K 470 1K 1K 1K 33K 4.7K 1K 22K 27K 18K 27K 27K 27K 39K 27K 8.2K 8.2K 15K 10K 8.2K 4.7K 8.2K 8.2K 1K 27K 8.2K 27K 8.2K
REMARK 1% 1% 1% 1% 1% 5% 1% 1% 5% 5% 5% 5% 5% 5% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W
1-249-432-11 CARBON 1-215-457-00 METAL 1-215-461-00 METAL
1-249-428-11 CARBON 1-249-434-11 CARBON 1-249-428-11 CARBON
-- 38 --
CPD-100ES
Note:
The components Identified by shading and mark ˇ are critical for safety. Replace only with part number specified.
Note:
The components identified by [ in this manual have been carefully factory-selected for each set in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used.
D
REMARK 330 470 470 680 100K 1.5K 1.5K 3.3K 3.3K 470 100K 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W
REF.NO. R944 R945 R946 R947 R948 R949 R950 R951 R952 R954 R956 R957 R958 R959 R960 R962 R963 R964 R965 R966 R968 R972 R973 R975 R976 R977 R979 R980 R981 R983 R984 R985 R986 R987 R989 R990 R991 R992 R993 R994 R995 R996 R997 R998 R999 R1801 R1806 R1810
PART NO. 1-249-424-11 1-249-424-11 1-247-903-00 1-247-883-00 1-247-883-00 1-247-883-00 1-247-883-00 1-247-883-00 1-247-883-00 1-249-425-11 1-249-421-11 1-215-441-00 1-249-420-11 1-249-428-11 1-249-425-11 1-249-429-11 1-249-429-11 1-247-883-00 1-249-415-11 1-247-895-91 1-247-883-00 1-24