Text preview for : LG BEKO 28CZ10RX SERVICE MANUAL.pdf part of LG 28CZ10RX SERVICE MANUAL
Back to : LG BEKO 28CZ10RX SERVICE | Home
TV
BEKO
BUYER NAME : LG BEKO MODEL : V30, T82 APPLICABLE SERIAL NO. : Immediately
TV
No. OF ISSUE : SB-BK0202 ISSUE DATE : 2002. 09. 06 BUYER(LGE) MODEL : 28CZ10RX, 32CZ10RX DATE OF CHANGE : 2002.08.24
SUBJECT : Damage of FBT due to Arcing (Replacing Termal brand FBT with Eldor FBT) ? Application Model : 1. GENERAL INFORMATION NO 1 1 « LOCA NO. TR502 TR502 R529 BEFORE PART NO. 058834-TR5 058234-TR5 119110 CHANGE DESC. / SPEC. 28" 16:9 FBT (Termal) 32" 16:9 FBT (Termal) RMF 1R J 1W AFTER PART NO. 057834-EL2 057234-EL3 119155 CHANGE DESC. / SPEC. 28" 16:9 FBT (Eldor) 32" 16:9 FBT (Eldor) RMF 1.5R J 1W I / N/C C C 3 C 3 C 3
2. SYMPTOM/REASON : The FBT is damaged due to arcing as shown in the attached picture. If the FBT is produced by Termal, it must be changed with an Eldor FBT. Note: The pin positions (on PCB) of Termal and Eldor brand FBT's are different. Thus, 3 metal eyelets should be removed and 5 eyelets should be added. Please apply the following procedure to replace Termal FBT with Eldor FBT: - Desolder the pins of Termal FBT and remove it. - Remove the metal eyelets in position E17, E19 and E20 by cutting heads on the component side of PCB (It is not necessary to remove E18) Not: It is needed to prevent a possible arcing from ferrite of Eldor FBT to the eyelets of old FBT. - Place metal eyelets (part code : 013114 ) to positions E12, E13, E14, E15 and E16. - Fasten eyelets by applying pressure to the solder side with a (+) type screwdriver and turn it. - Solder new Eldor FBT on the positions E12, E13, ... (see the component-side layout below). « If CPT brand is 28" Video Color (W66EJU023X015), then Heater resistor R529 has to be replaced from 1R to 1.5R to decrease the Heater voltage (for other CPT brands and screen sizes, the R529 should not be replaced). ? ? The part number of FBT is actually 058838(28") and 058238(32") in SPPL. So, if you order with those part number, Beko will deliver Eldor FBT automatically. « FILE THIS SERVICE BULLETIN WITH YOUR SERVICE MANUAL « I/C : INTERCHANGEABILITY CODE
code
N/C : NUMERAL CODE
1. To improve performance 2. To improve productivity 3. To improve reliability 4. Change of material or dimension 5. Addition 6. Deletion 7. Correction
A B
Interchangeable : Old and new parts can be used in products as the bulletin regardless of manufacture date. Old parts can be substituted for new parts : Old parts can be used in previous products only. But new parts can be used regardless of manufacture date. New parts can be substituted for old parts : Only new parts can be used in products regardless of manufacture date. Not interchangeable : New parts can be used in new products only.
Cengiz ARAT CHIEF ENGINEER, R&D Sükrü AKTAS MANAGER, QA
C D
l
Issued by BEKO Engineering & Customer Service Division
CONTENTS
PAGE
Safety Instructions 3 Technical Specifications 4 Pin Voltages of IC's 5 Pin Voltages of Some Transistors 8 Oscillograms 9 Electrical and Service Adjustments 12 Trouble Shooting Guide 16 Parts List 23 Circuit Diagram PIP Module 30 Circuit Diagrams Attached
27/05/2002, Version 2
SAFETY INSTRUCTIONS
GENERAL GUIDELINES 1. It is advised to insert an isolation transformer in the AC supply before servicing a hot chassis. 2. Potentials as high as 33KV are present when this receiver is in operation. Operation of the receiver without the rear cover involves the danger of a shock hazard from the receiver power supply. Servicing should not be attempted by any one who is not competent with the precautions necessary when working on the high voltage equipment. Always discharge the anode of the tube. 3. When servicing observe the original lead dress in the high voltage circuits. If a short circuit is found, replace all the parts which have been overheated or damaged by the short circuit. 4. Always use the manufacturer's replacement safety components. The critical safety components marked with on the schematics diagrams should not be replaced by other substitutes. Other substitute may create the electrical shock, fire or other hazards. Take attention to replace the spacers with the originals. Furthermore where a short circuit has occurred, replace those components that indicate evidence of overheating. 5. After servicing, see that all the protective devices such as insulation barriers, insulation papers, shields and isolation R-C combinations are correctly installed. 6. When the receiver is not being used for a long time of period of time, unplug the power cord from the AC outlet. 7. After servicing make the following leakage current checks to prevent the customer from being exposed to shock hazard. LEAKAGE CURRENT COLD CHECK 1. Unplug the AC cord and connect a jumper between the two prongs of the plug. 2. Turn the receiver's power switch on. 3. Measure the resistance value with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the receiver, such as screw heads, aerials, connectors, control shafts etc. When the exposed metallic part a return path to the chassis the reading should be between 4Mohm and the 20Mohm. When the exposed metal does not have a return path to the chassis, the reading must be infinite. LEAKAGE CURRENT HOT CHECK 1. Plug the AC cord directly in to the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 2Kohm 10W resistor in series with an exposed metallic part on the receiver and an earth, such as a water pipe. 3. Use an AC voltmeter with high impedance to measure the potential across the resistor. 4. Check each exposed metallic part and check the voltage at the each point. 5. Reverse the AC plug at the outlet and repeat each of the above measurements. 6. The potential at the any point should not exceed 1.4 Vrms. In case a measurement is outside the limits specified, there is the possibility of a shock hazard, and the receiver should be repaired and rechecked before it is returned to the customer.
HOT CHECK CIRCUIT AC-Voltmeter
TO INSTRUMENTS EXPOSED METALLIC PARTS
Water pipe (earth)
2 K Ohm
Figure 1 X-RAY RADIATION WARNING The primary source of X-ray radiation in this receiver is the picture tube. The chassis is specially constructed to limit X-ray radiation. For continued X-ray radiation protection, replace the tube with the same type of the original one. CAUTION AFTER REMOVAL OF THE ANODE CAP, DISCHARGE THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE CARBON PAINTED ON THE CRT WITH A HIGH VOLTAGE PROBE AND MULTIMETER (SELECT VDC) AND THEN SHORT CIRCUIT DIRECTLY TO DISCHARGE COMPLETELY.
TECHNICAL SPECIFICATIONS
Power source: Power consumption (max.) 1: 220-240 VAC, 50-60Hz 120 W 125 W 145 W 140 W 150 W 155 W 165 W 160 W 3W 75Ohm, coaxial type PAL BG PAL SECAM BG PAL SECAM BG DK PAL SECAM BG LL' PAL I VHF BAND I , VHF BAND III , CABLE TV UHF BAND 3.58&4.43 MHz Stereo : Mono : High Voltage : 2 x 10W RMS at %10 THD (Except 21" Pure Flat) 2 x 7W RMS at %10 THD (21" Pure Flat) + 20W RMS at %10 THD (if subwoofer available) 2 x 7W RMS at %10 THD 25", 28"4/3 28"16/9, 29", 32" Super Flat 32" Pure Flat, 33" CH2-4 CH5-12 S1-41 CH21-69 21" Pure Flat 25", 28" Mono 25", 28" 4/3, 29" Pure Flat 29" Super Flat 28" 16/9 Super Flat 28" 16/9 Pure Flat, 32" Super Flat 32" Pure Flat 33"
Standby power consumption : Aerial impedance : Receiving system 2:
Receiving channels:
NTSC Playback Frequencies: Audio outputs :
28.5 ± 0.5 KV 29.0 ± 0.5 KV 29.5 ± 0.5 KV %25.6 ± %38 of EHT 0-1400 V 6.2 ± 0.2 Vrms AV1/2 IN AV1 IN AV1/2 OUT AV2 IN (RCA)
Focus voltage : Grid 2 voltage : Heater voltage : Video/Audio Terminals :
Video : 1 Vpp,75 Ohm Audio : 0.5 Vrms, >10 Kohm RGB Video : 1 Vpp, 75 Ohm Audio : 0.5 Vrms, <1 Kohm Video : 1 Vpp, 75 Ohm Audio : 0.5 Vrms, >10 Kohm
Operating temperature : Safety X-Ray radiation
1 2
0-45 Degrees IEC 65 /BS P2N ACC. IEC 65/BS P2N
: :
: 20W should be added to find the max. power consumption of the models with subwoofer. : TV set is produced to receive "one" of these colour and sound systems.
12
IC 301 (MSP 3400G) MULTI STANDARD SOUND PROCESSOR
Pin 1 Not connected 2 Gnd 3 Gnd 4 Digital control input/output 5 Digital control input/output 6 Gnd 7 Standby (in normal operation it must be high) 8 Not connected 9 SCL 10 SDA 11 Not connected 12 Not connected 13 Not connected 14 Not connected 15 Not connected 16 Not connected 17 ADR Bus Clock Output 18 Digital Circuitry Supply Voltage 19 Digital Circuitry Supply Ground 20 Not connected 21 Not connected (Ground) 22 Not connected (Ground) 23 Not connected (Ground) 24 MSP RESET input 25 Headphone sound output (R) 26 Headphone sound output (L) 27 Reference analog ground 28 Speaker output (R) 29 Speaker output (L) 30 Not connected 31 Not connected 32 Not connected 0 0 0 0 0 4.9 4.9 2.4-2.6 1.8-2.1 2.4 2.4 2.4 4.9 0.7 0.7 0.7 4.9 0 0.7 0 0 0 4.9 2.1 2.1 0 0.1-2.1 0.1-2.1 0.1-2.1 0.1-2.1 0 Connection V DC Pin Connection V DC 3.7 3.7 0 3.7 3.7 8 0 3.7 3.7 3.7 0 3.7 3.7 0 3.7 3.7 0 3.7 3.7 2.5 3.7 0 4.9 1.5 1.5 0 0 2.3 2.3 0 33 Scart 2 sound output (R) 34 Scart 2 sound output (L) 35 Reference analog ground 36 Scart 1 sound output (R) 37 Scart 1 sound output (L) 38 Volume capacitor Headphone 39 Analog Supply High Voltage (8V) 40 Volume capacitor Speaker 41 Ground for Analog Power Supply High Voltage 42 Internal Analog Reference Voltage 43 Scart 4 input (L) 44 Scart 4 input (R) 45 Analog Shield Ground 46 CINCH - sound input (L) 47 CINCH - sound input (R) 48 Analog Shield Ground 49 Scart 2 sound input (L) 50 Scart 2 sound input (R) 51 Analog Shield Ground 52 Scart sound 1 input (R) 53 Scart 1 sound input (L) 54 A/D converter ref. Voltage 55 Mono sound input 56 Ground for Analog Power Supply Voltage 57 Analog Power Supply Voltage (5V) 58 IF input 1 59 IF Common reference for IF IN1/IN2 60 IF input 2 61 Factory test mode enable (ground) 62 Crystal oss. input 63 Crystal oss. output 64 Not connected (Ground)
IC303, IC304 (TDA7263) Audio Output IC
Pin 1 Left In 2 Left In V 3 Mute 4 Right In V 5 Right In 6 Gnd Connection V DC 1.6 1.6 15.3 1.6 1.6 0 Pin 7 8 Right out 9 VS 10 Left out 11 12 Left In Connection V DC 0,5-0,9 14.2 28 13.9 0,5-0,9 0.6
IC501 (TDA835X) Vertical Deflection Output IC
Pin 1 Input A 2 Input B 3 Supply voltage 4 Output B 5 Gnd Connection V DC 0,98 (0) 0.94 (0) 14,7 (1.0) 7,55 (0,4) 0 (0) Pin Connection V DC 45,6 (10,9) 7,64 (0,1) 0,3 (0) 7,9 (0) 6 Vertical Flyback Supply Voltage 7 Output A 8 Guard Output 9 Feedback Input
IC601 (MC44608 AP) Power Supply IC
Pin 1 Demag 2 I sense 3 Control input 4 Gnd (*) Standby values are given in parenthesis Connection V DC 0.85 (0.0) 0.1 (0.32) 5 (5.5) 0 Pin 5 Driver 6 VCC 7 Not connected 8 VI Connection V DC 2.1 (0.14) 12.3 (8.8) 116 (117)
14
PIN VOLTAGES OF SOME TRANSISTORS
1. PH601 (PC127FY) PHOTOCOUPLER Standby VDC ON VDC Pin 12.5 11 1 2 3 4 11.5 5.5 8.8 10 5 12.3 4. T605 (BC848) NPN TV ON VDC B C E 0 T605 Standby VDC B C E 0 TV ON VDC B 0.1 C 0.7 E 0 2. T603 (BC848) NPN Standby VDC B C E T603 0.6 0.02 0 TV ON VDC B C E 0.1 0.3 0
3. T604 (BC848) NPN Standby VDC B T604 C E 0
0.02 12.7
0.7 0.05
0.6 0.02
5. T606 (BC848) NPN Standby VDC B T606 0.6 C 0 E 0 TV ON VDC B 1 C 6.8 E 0
6. T607 (BC848) NPN Standby VDC B T607 0.6 C 0 E 0 TV ON VDC B 0.1 C 2.5 E 0
7. T307 (BC848) NPN Standby VDC B T307 0.6 C 0 E 0 TV ON VDC B 0.1 C 15 E 0
OSCILLOSGRAPHS OF SOME IC PINS
Note: TV is connected to a patern generator (Colour bar, sound 1 kHz).
1. IC101 (TDA956X)
Pin 30 2V/div, 20 usn/div, Vpp=4.9 V, 15625 kHz
Pin 31 2V/div, 20 usn/div, Vpp=5.6 V, 15625 kHz
Pin 38 2V/div, 20 usn/div, Vpp=2.9 V, 15625 kHz
Pin 40 500 mV/div, 20 usn/div, Vpp=1.2 V, 15625 kHz
Pin 47 500 mV/div, 20 usn/div, Vpp=2.1 V, 15625 kHz
Pin 55 500 mV/div, 20 usn/div, Vpp=1.65 V, 15625 kHz
Pin 56 500 mV/div, 20 usn/div, Vpp=2.7 V, 15625 kHz
Pin 57 500 mV/div, 20 usn/div, Vpp=2.6 V, 15625 kHz
Pin 58 500 mV/div, 20 usn/div, Vpp=2.4 V, 15625 kHz
Pin 71 2 V/div, 1 msn/div, Vpp=5.2 V
Pin 72 2 V/div, 1 msn/div, Vpp=5.2 V
2. IC301 (MSP34XX)
Pin 28 500 mV/div, 1 msn/div, Vpp=1.8 V
Pin 29 500 mV/div, 1 msn/div, Vpp=1.8 V
3. IC501 (TDA835X)
Pin 1 500 mV/div, 10 msn/div, Vpp=1.4 V, 50Hz
Pin 2 500 mV/div, 10 msn/div, Vpp=1.4 V, 50Hz
Pin 7 500 mV/div, 10 msn/div, Vpp=44.6 V, 50Hz
4. T501 (2SK2381)
Gate (EW drive) 200 mV/div, 50 usn/div, Vpp=268 mV, 15625 Hz
Drain (EW drive) 2 V/div, 10 usn/div, Vpp=10.7 V, 50 Hz
1. ELECTRICAL ADJUSTMENTS
1.1. Supply Voltage Adjustment Connect a digital voltmeter to the cathode of diode D611 at the AV1 mode of the TV and set the screen voltage to the minimum with the screen potentiometer. Adjust the main supply voltage (B+) with P601 potentiometer to the following value (after adjustment, readjust Screen voltage). 21" Pure Flat : 132 VDC 25" : 145 VDC 28" : 145 VDC (147 VDC for A66EAK071X11) 28" Pure Flat 16/9 : 140 VDC 28" Super Flat 16/9 : 140 VDC 29" Pure Flat : 125 VDC 29" Super Flat : 125 VDC 32" Pure Flat 16/9 : 140 VDC 32" Super Flat 16/9 : 131 VDC 33" : 158 VDC
2. SERVICE ADJUSTMENTS
You need the special service remote control to enter and exit the service menu of the TV (you can order it from the manufacturer). All buttons of the Service RC are same with the user remote control, only service menu In / Out is added to it (please see the picture below). Navigation Service In/Out : Enters to / exits from the Service Menu P+ / P: Moves upward / downward inside the menu V+ / V: Changes the values or options
2.1. AGC Adjustment · · · Apply an RF signal with amplitude 70±1 dBuV to the antenna input of TV with a pattern generator (switch sound carrier to Off and switch "Video Ext" to On). Switch on the Service Menu with the Service RC and find the AGC with P+ / P- buttons. Measure the 38.9 MHz signal on pin 11 (IF) of Tuner with an oscilloscope. Adjust "AGC" to get following values: PAL BG, PAL SECAM BG, PAL SECAM BG-DK, PAL I versions : 840 ± 20 mVpp PAL SECAM BG-LL version : 600 ± 20 mVpp PAL BG MONO, PAL SECAM BG MONO : 750 ± 20 mVpp PAL I MONO : 900 ± 20 mVpp Substract 5 from "AGC" value and change "TEST" to this value. Exit from the service menu with the Service RC.
· ·
2.2. Screen Adjustment Adjustment is change according to SW versions. New SW versions start from SB8643_A05, SB8643_B04, SB8643_C04, SB8643_D04, SB8645_A05, SB8645_B04, SB8645_C03 and SB8645_D04. · If CRT brand is Philips and SW is old version, then Set Brightness value to "00" in the Picture menu and store. · Enter the Service Menu with the Service RC and select "SCRN" option with P+ / P- buttons and switch to ON with V+ / V- button. For new SW versions (or Philips CRT) "BRI 00" is shown on the screen. For old SW versions "BRI 32" is shown on the screen. · Adjust the screen potentiometer to the level where the screen is just black. · By pressing one of V+ / V- buttons, get the picture (SCRN is switched to Off). · Exit from the Service menu. · If CRT brand is Philips and SW is old version, Set Brightness value to "32" in the Picture menu and store. 2.3. Geometry Adjustments · · · · · · · · · · Apply a Cross Hatch Test pattern. Enter Service Menu with Service RC and select "VSLP" option with P+ / P- buttons (In this option, the upper half part of the pattern is shown and lower half part is blanked). Adjust VSLP such that middle line of the pattern is cut. For 16/9 sets, adjust VZOM to 25. On 4/3 sets, when VZOM is selected, set switches to 16/9 mode. In this case, adjust the circle of the pattern just touches to the upper and lower edges. Re adjust the VSLP if required. Adjust vertical position with VSHT, vertical linearity with SCOR and vertical height with VAMP. For 4/3 sets, adjust the horizontal amplitude with EWW. For 16/9 sets, adjust the 16/9 horizontal amplitude with EWW1 and 4/3 horizontal amplitude with EWW (EWW value is 21 lower than EWW1 value). For 16/9 sets, find the VZM1 option and adjust such that second lines from top and bottom just touches to the edges. Adjust horizontal centering with HSHT, parabola with EWPW and trapezium with EWT. For 4/3 sets, adjust the 16/9 general parabola with EWP1. Adjust the upper corner parabola with EWCU and lower corner parabola with EWCL, vertical parallelogram with HPAR, horizontal bow with HBOW.
For PIP versions : Select "PIP PRESS OK" and press "OK" button in the service menu. Adjust "HORPOS0" for horizontal shift of PIP window, "VERPOS0" for vertical shift of PIP window (press "POS" button to place PIP to the left-top corner), "HORPOS1" for 12-window PIP horizontal shift, "HORPOS2" for 11-window PIP horizontal shift, "HORPOS4" for right PIP horizontal shift. 2.4. White Balance Adjustment · · · · Enter the Service Menu with the Service RC and select "GRN" option with P+ / P- buttons and adjust it to "32" V+ / V- button. Adjust RED and BLUE for white balance. If white balance can not be adjusted properly change GRN value. Adjust BLOR and BLOG for red and green cut off. Exit from the Service menu.
2.5. Feature Options Tuner STD Head SCRN AV SSTD STYP Toptext Fasttext : Panasonic, Phillips, Sharp, Temic : STBY-On (Default, Automatic switch off is active), STBY-Off (can be used during repair) : Yes (Headphone available), No : Off, On (used for screen adjustment) : 01 (1 Scart), 03 (2 Scarts), 04 (2 Scarts + Front AV), 05 (2 Scarts + Front AV+ SVHS) : BG only, I only, BG+DK, BG + LL', All SYS : NICAM On (available), NICAM Off : Yes (available), No : Yes (available), No
: West (West Europe), East (East Europe), Cyrillic, Arabic, Hebrew, Greek A type SW includes East, West, Greek. B type SW includes East, West, Cyrillic, Arabic. C type SW includes East, West, Cyrillic, Hebrew. D type SW includes East, West, Cyrillic. Hotel : On (Hotel Mode), Off (TV Mode) Subwoofer : Yes (available), No CRT : 4/3, 16/9 Peak1 : Yes (16/9 sets), No (4/3 sets) AVV : Yes (Auto AV switching is active), No (Deactive). PAL : Yes (PAL only versions), No (Other versions) SAWF 1) : 01 (PAL BG, PAL-SECAM BG, PAL I or PAL-SECAM BG-DK without FTZ) 02 (SECAM LL' or PAL-SECAM BG-DK with FTZ) 1) Available in only SW versions of Mono versions. 2.6. Factory Settings for Service Mode 1. Values given in Table 1 are typical values and can vary according to the CRT type. 2. PF means Pure Flat and SF means Super Flat. 3. The values in the table are decimal and shown in paranthesis on the OSD of TV. 28" 28" 32" 32" 29" 29" 21" 25" 28" 16/9 16/9 16/9 16/9 PF SF PF PF SF PF SF 14 14 14 14 14 14 14 14 00 00 00 00 00 00 00 00 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 40 40 35 35 32 35 40 40 34 34 32 33 26 33 34 34 32 30 28 30 25 30 31 31 40 36 41 40 33 40 41 41 04 04 04 04 04 04 04 04 20 20 20 20 20 20 20 20 32 32 32 32 32 32 32 32 40 40 40 40 40 40 40 40 04 05 04 04 05 05 04 04 32 32 32 32 32 32 32 32 28 28 17 24 28 27 24 24 40 32 22 14 32 39 07 07 55 32 48 38 38 42 22 22 04 17 08 08 14 12 12 12 38 35 35 40 31 29 29 29 60 60 37 36 55 57 39 39 48 46 42 42 43 45 45 45 30 25 25 17 31 25 17 17 24 29 27 28 28 26 31 31 27 32 32 32 34 29 35 35 01 01 10 10 01 01 10 10 39 39 39 39 39 39 39 39 06 11 06 06 11 11 06 06 32 32 32 32 32 32 32 32 48 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 09 09 09 09 09 09 09 09 02 08 05 05 09 09 05 05 58 57 - 60 60 58 59 - 59 59
TXT table
33" 14 00 32 32 42 34 27 37 04 20 32 40 05 32 26 27 37 20 35 62 48 25 25 32 01 39 11 32 32 32 09 13 -
AGC EEPE PEAK GRN RED BLUE BLOG BLOR YDLY SAT HUE CON CDR BRI EWT EWCU EWCL EWPW HSHT EWW VAMP SCOR VSHT VSLP RGB 1) VZOM PWLT IFOF HPAR HBOW TEST EWP1 EWW1 VZM1 Table 1
1)
Automatic gain control Reset the eeprom, all values lost Peaking Green level Red level Blue level Black level offset green Black level offset red Luminance delay Saturation Sharpness Contrast Cathode Drive Level Brightness East West Trapezium EW upper corner EW lower corner EW parabola width Horizontal shift East West Width Vertical amplitude S correction Vertical shift Vertical slope OSD brightness level Vertical zoom Peak white limiting Offset IF demodulator Horizontal parallelogram Horizontal bow Added for EMC purposes (=AGC-5) 16/9 EW parabola width (for only 4/3 sets) East West Width (for only 16/9 sets) Vertical Zoom (for only 16/9 sets)
For old SW versions (see section 2.2) RGB value is "01". For new SW, RGB is "01" for 4/3 and "10" for 16/9 sets.
2.7 Software Versions During exit from service menu, the software version and feature options (hexadecimal number) are shown on the screen. For example: SB8643_X05, C697H. Stereo software versions of 14.2 are named as follows: SB8643_X.. for TDA9563 (intercarrier) SB8645_X.. for TDA9565 (QSS) Mono Software versions are named as follows: SC3325-X.. for TDA9555H (only QSS) PIP Software versions are names as follows: SB8963_X.. for TDA9563 (intercarrier) SB8965_X.. for TDA9565 (QSS) ".." shows version number (for example 05). "X" shows OSD language group. OSD Languages per group are given below: 1. 2. 3. 4. 5. 6. 7. 8. GROUP A ENGLISH GERMAN FRENCH ITALIAN SPANISH PORTUGAL DUTCH GREEK GROUP B ENGLISH FRENCH POLISH HUNGARY SLOVAK CZECH IRAN ARABIAN GROUP C ENGLISH GERMAN TURKISH SWISS DANISH NORWEGIAN FINNISH HEBREW GROUP D ENGLISH RUSSIAN SERBIAN BULGARIAN ROMANIAN MACEDONIAN CROATIAN SLOVENIAN
Note: 1. All values in the diagrams are for 230 VAC mains supply. 2. Before replacing T601, check following components: R640, R604, R605, R609, C615. 3. Burst type standby mode was designed (Fixed frequency is 21.5 kHz for standby and 38.8 kHz for normal operation) . In standby the output voltages drop to about 1/10 of the normal operation values (except +12V which stays same), i.e. from +145V to 14.7V, from 15V to 1.1V, from 28V to 2.5V. In standby, Standby signal from IC101 is high. Then, T605 conducts, T604 blocks and thristor TH601 conducts. Therefore, +145 line which is now14.7V is connected to 12V. The regulation is done by ZD603 in standby and by ZD602 (TL431) in normal mode.
POWER SUPPLY DEFECTS (I)
No operation Stand-by LED is off No SMPS Voltages
Check 300V DC on C613
NO
Check Fuse ST601
YES
Check power switch, L601, Diode SD602, D605, D604, Capacitor C603, P603
YES
Check transistor T601 is OK. Drain 300 VDC, 2.3-2.8 VAC Gate 1.2 VDC
NO YES
Check and replace Fuse ST601
NO
If C613 has a voltage lover than 300 VDC replace it
YES NO
Check 120 VDC at pin 8 of IC601, MC44608
D601 and 602 are open circuit
YES NO
Check 8.8 VDC at pin 6 of IC601
C610 is open or capacitor value is low. D6107 is short or IC601 is defective.
YES NO
Check 1.2 VDC at pin 5 of IC601
YES
If R639 is OK, replace IC601
Check and replace T601, 2SK2545
POWER SUPPLY DEFECTS (II)
No operation Stand-by Voltages OK
Check 4.2 VDC at pin 6 of IC101
NO
Check connection to R409 and R641
YES NO
Switch on the TV set. Check voltage 0.05 V pin 6 of IC101 and 0.28 V at R439
Check the voltage 3.3 V at pins 59, 66 of IC101 and pin 8 of IC402
YES
Check and replace IC101
POWER SUPPLY DEFECTS (III)
Stand-by Voltages are abnormal
Check the standby voltage (it should be 14.7V). This voltage is 20V-50V.
YES
Check and replace R617, R641, R626, T603, ZD603, T604, T605, T607, C621, C623
NO YES
Standby voltage is around 160 V instead of 14.7V
Check the voltage 4 VDC at the cathode of D615. Check and replace T605 and PH601
POWER SUPPLY DEFECTS (IV)
When TV is on, voltages 145V,15V,11.8V, 3.3V, 8V, 5V, 28V are not at their proper values
+B voltage is around 160V instead of 145V.
YES
Check and replace T607, R625, R645, PH601, ZD602.
NO
+B voltage is 20-80V instead of 145V.
YES
There should be 14 VAC at R612 and 11.8 VDC at cathode of D614.
NO
Voltages 15V, 8V, 5V are missing. Other voltages are OK.
YES
Check the voltage 16 VAC at fuse S602. If it is missing check and replace S602 and D613
NO
Voltages 8V, 5V are missing. Other voltages are OK.
YES
Check and replace IC603, R631, R627, T606, C638, IC602, C637.
PICTURE AND COLOUR DEFECTS
No picture Raster OK
Check video out signal at pin 38 of IC101
NO
Check the tuner pin voltages. Check the voltage 3.6-4.6 V at pin 18, 19 of IC101. Check and replace F101, IC101.
YES
Only white raster visible on screen
YES
Check CVBS signal with an oscilloscope. The video signal goes through R103, T104, R154, F104, T105, C150 to pin 40 of IC101
NO
There are flyback lines on the screen
YES
Check Hor. Flyback signal at pin 31 of IC101. Check and replace C129 which is connected to pin 11 of IC101.
NO
There are black drops on the screen.
YES
Check and replace C139
NO
No picture. There is a Red, Green or Blue raster on the screen.
NO
Check and replace R167, R206, R118, R136, R137, R135, IC101.
HORIZONTAL DEFLECTION CIRCUIT DEFECTS
Power supply voltages are OK. There is no high voltage
Check 15V at the collector of T503.
NO
Check and replace R503 and TR501 Hor. Driver transformer
YES
Check the voltages 1.42 VDC and 0.92 VAC at + pin of C502
NO
Check voltage 8V at pin 9, 39 of IC101. If present replace IC101.
YES
Check the voltages 0.28 VDC, 0.92 VAC and 15625 Hz signal at the base of T503.
NO
Check and replace D505 and C503.
YES
Remove T504. Check the voltage 145 VDC at the collector point.
NO
Check and replace R525 and Line Output Transformer.
YES
Check 2 VAC at the base of T504.
NO
Check and replace T503, TR501 and R513.
YES
Check and replace D507, D508, C518, C519, C521. Place T504 to its position. Check the operation of Line Output Transformer.
NO
Replace Line Output Transformer.
YES
There is a noise heard from Line Output Transformer. Check and replace T501, R516 and C520.
VERTCAL DEFLECTION CIRCUIT DEFECTS
There is a horizontal line on the screen
Check 16 VDC at pin 3 of IC501.
NO
Check and replace R127 (at pin 20 of IC101), C126 (at pin 21 of IC101), R526, D513, C527, R521.
YES
Check 35 VDC at pin 6 of IC501.
NO
Flyback lines are visible. Check and replace R527, D512, C526, R522, C517.
YES
Check 2.2 VDC at pin 1 of IC501.
NO
If R122 is open IC501 becomes defective and 16 VDC components fail. Check them before replacing IC501.
YES NO
Check 2.2 VDC at pin 2 of IC501.
Lower half of the screen is black. Check and replace R123 and IC101.
YES NO
Check 7.4 VDC at pin 7 of IC501. Check 7.2 VDC at pin 4 of IC501.
A Horizontal line is visible. Check and replace R518, R519 and IC501.
YES
Replace IC501
AUDIO DEFECTS (I)
No sound. Picture is OK.
Check 28 VDC at pin 9 of IC304.
NO
Check and replace components R341, D612, S603.
NO
Audio signal at pins 1,5 of IC304 are OK. No sound.
NO
YES
Check signals at pins 8, 10 of IC304. Check and replace IC304.
Audio signal at pins 28,29 of IC301 are OK. No sound.
NO
YES
Check and replace R307, T301, R310, C326, C332, R308, T305, R319.
Audio signal at R150 Trap Filter is OK. No sound.
NO
YES
Check and replace C230 and IC301.
Check and replace components R156, L105, L106, C158, C159, C160, R150.
AUDIO DEFECTS (II)
YES
Volume decreases to minimum.
Check and replace R437 and R444. Check 3.3 VDC at pin 80 of IC101.
NO
Volume increases to maximum.
YES
Check and replace R436 and R445. Check 3.3 VDC at pin 78 of IC101.
NO
Volume Up/Down buttons change programme numbers.
NO
YES
Check and replace R438 and R441. Check 3.3 VDC at pin 1 of IC101.
Pop sound is heard when switch off.
YES
Check and replace R429, R317, C335. Standby voltages of T307: B(0.6V), C(0V) Operation voltages of T307: B(0.1V), C(15.5V)
NO
Check and replace R321, R318, T307. Check and replace IC304.
PARTS LIST
PART NO 291103 293108 290473 252112 250113 292334 250111 292479 293230 250470 259223 294231 274107 290561 290222 250111 291822 294476 251107 294475 291822 292479 290684 291225 291473 291474 251478 250470 294111 294331 299152 292110 250227 292105 253101 252229 252112 253106 291477 290334 272101 251478 274230 200680 292223 252476 272154 272103 271331 294109 273104 273114 273119 273120 273131 273151 273228 273331 274563 274563 DESCRIPTION CC-CHIP 100PF J 50V /0805 N CC-CHIP 10NF K 50V /0805 X7 CC-CHIP 47PF J 50V /0805 NP EC 100UF 16V 11*6 R:5 C-ELA 1UF 25V 11*5 R:5 CC-CHIP 3.3NF K 50V /0805 X7R EC 1UF 16V 11*5 R:5 CC-CHIP 4.7NF K 50V /1206 X CC-CHIP 22NF K 50V /0805 X7 C-ELA 4.7UF 16V 11*5 R:5 EC 2.2UF 63V 11*5 R:5 CC-CHIP 220NF K 16V /0805 X C-PEM 100NF J 100V R:5 CC-CHIP 56PF J 50V NPO 0805 CC-CHIP 22PF J 50V /0805 NP C-ELA 1UF 16V 11*5 R:5 CC-CHIP 820PF J 50V /0805 NP0 CC-CHIP 470NF K 16V /0805 X EC 10UF M 16V 11*5 R:5 CC-CHIP 470NF M 25V /1206 Z CC-CHIP 820PF J 50V /0805 N CC-CHIP 4.7NF K 50V /1206 X7R CC-CHIP 68PF J 50V /0805 NP CC-CHIP 220PF K 50V /0805 X CC-CHIP 470PF K 50V /0805 X CC-CHIP 470PF J 50V /1206 N EC 47UF 16V 11*5 R:5 EC 4.7UF 16V 11*5 R:5 CC-CHIP 100NF K 25V /0805 X CC-CHIP 330NF K 16V /0805 X CC-CHIP 1.5PF C 25V/0805 CC-CHIP 1NF K 50V /0805 X7R EC 2.2UF 16V 11*5 R:5 CC-CHIP 1NF K 50V /1206 X7R EC 1000UF 35V 25*13 R:5 EC 220UF 16V 11*8 R:5 EC 100UF 16V 11*6 R:5 EC 1000UF 25V 20*13 R:5 CC-CHIP 470PF J 50V /0805 N CC-CHIP 33PF J 50V /0805 NP C-PEM 1NF K 50V R:5 EC 47UF 16V 11*5 R:5 C-PEM 220NF J 100V R:5 CC 68PF J 500V NPO R:5 CC-CHIP 2.2NF K 50V /0805 X EC 470UF 25V 11*10 R:5 C-PPM 1.5NF J 1600V R:15 C-PPM 1NF J 2KV R:15 C-PPM 330PF J 1500V/1600V R CC-CHIP 100NF K 50V /0805 X C-PPM 10NF J 1.5/1.6KV R:22 C-PPM 10NF J 1.5/1.6KV R:15 C-PPM 11NF J 1.5/1.6KV R:22 C-PPM 12NF J 1.5/1.6KV R:22 C-PPM 13.1NF J 1.5/1.6KV R: C-PPM 15NF J 1KV R:15 C-PPM 22NF J 1KV R:15 C-PPM 33NF J 1KV R:15 C-PPM 560NF J 250V R:15 C-PPM 560NF J 250V R:15 21",25",32",28"4/3 25",28"4/3 21" PF 33" 28"16/9 29",32" 16/9 sets 4/3 sets 21" PF 25",28"4/3 28"16/9 21"PF, 32" EXT.SPEAK. EXT.SPEAK. MONO SOUND MONO SOUND MONO SOUND MONO SOUND MONO SOUND 1. MONO SOUND NOTES C101 C103 C104 C105 C108 C109 C110 C112 C118 C123 C124 C125 C126 C131 C136 C142 C144 C145 C146 C151 C158 C178 C186 C202 C209 C214 C217 C220 C229 C239 C308 C322 C330A C332 C338 C344 C352 C354 C405 C413 C503 C504 C505 C506 C508 C512 C513 C513 C513 C515 C518 C518 C518 C518 C518 C519 C519 C519 C520 C521 C521 C516 C509 C527 C639 C524 C523 C334 C340 C346 C353 C355 C406 C337 C620 C401 C402 C203 C366 C210 C221 C222 C235 C241 C313 C324 C224 C226 C302 C225 C314 C160 C148 C162 C167 C638 C166 C165 C139 C507 C120 POSITION NUMBERS C111 C149 C107
PARTS LIST
PART NO 274684 274684 250100 251225 272110 274224 274105 202105 274102 252150 201471 203330 202220 253101 293681 293474 252104 251228 201108 294108 293332 293475 251120 251109 273225 202221 202106 273471 201472 291101 303195 303223 302296 302289 303195 303109 303244 302948 300305 303227 303209 303217 303308 303215 303214 303206 303228 303988 303942 303900 303993 303991 056749 056760 056709 056708 056767 056721 DESCRIPTION C-PPM 680NF J 250V R:15 C-PPM 680NF J 250V R:15 EC 1UF 160V 11*6.3 R:5 EC 22UF 16V 11*5 R:5 C-PEM 1NF J 100V R:5 C-PEM 220NF K 275V-AC R22. C-PEM 100NF J 250V R:10 CC 1NF K 1KV Y5P R:5 C-PEM 100NF J 63V R:5 EC 150UF 400V 40*22 R:10 CC 470PF 2KV C-PPM 33NF J 630V R:15 CC 2.2NF M 250VAC Y5U R:10 EC 1000UF 35V 25*13 R:5 CC-CHIP 68NF K 25V /0805 X7 CC-CHIP 47NF K 50V /0805 X7 EC 100UF 200V 25*16 R:7.5 EC 22UF 200V 11.5*8 R:5 CC 100PF 500V NPO R:5 CC-CHIP 100NF K 50V /1206 X CC-CHIP 33NF K 50V /0805 X7 CC-CHIP 47NF K 50V /1206 X7 EC 10UF 10V 5*4 R:5 EC 10UF 250V 16*10 R:5 C-PEM 22NF J 63V R:5 C-CE 2.2NF K 2KV Y5P R:7.5 CC 1NF K 50V Y5P R:5 C-PEM 47NF K 63V R:5 CC 470PF K 50V SL R:5 CC-CHIP 100PF J 50V /1206 N DIODE 4148 MELF DIODE-CHIP BA682 SOD80 DIODE 1N4148 26MM DIODE 1N4148 52MM DIODE 4148 MELF DIODE ERC06-1500 DIODE RGP30K DIODE 1N4007 DIODE BA157 DIODE RGP15J DIODE BAV21 DIODE RGP10J DIODE RF2007 DIODE RGP10G DIODE UF4006 DIODE RGP30MS DIODE RGP30D LED LTL 4224 RED (SHORT LEG LED LTL4224 RED LED ROT LED LTL4221N D:3 R/D RED LED IR SIR563SB3F 23/940 SAW FILTER OFW G1985M SAW FILTER OFW J1956M SAW FILTER OFW K3953M SAW FILTER OFW K3958M SAW FILTER OFW K9456M SER.FILTER TPS5.5MWA PAL BG PAL I PAL SECAM DK SECAM LL' SECAM LL' PAL SECAM BG DK 28" 25" 21",29",32",33" LL' LL' EXT.SPEAK. SVHS NOTES 33" 28"16/9 C521 C521 C522 C528 C529 C601 C603 C604 C606 C613 C614 C615 C616 C621 C624 C625 C629 C629 C631 C632 C634 C636 C637 C702 C704 C705 C920 C940 C962 C981 D102 D103 D401 D401 D503 D507 D508 D509 D510 D513 D515 D601 D602 D607 D608 D611 D612 D901 D901 D901 D980 D981 F101 F101 F101 F101 F102 F104 D613 D702 D615 D603 D614 D609 D604 D605 D703 D704 D701 D511 D512 D104 D402 D402 D504 D505 C921 C941 C963 C982 C922 C923 C901 C703 C326 C626 C627 C619 C602 C701 C605 C607 C608 POSITION NUMBERS
PARTS LIST
PART NO 56709 056745 053740 056640-01 056744 056640-01 458642 458643 458321 458964 458965 452510 452575-01 452800 452595 452374 452368 452482 452784 452976 452487-01 451517 451518 50S310 452520 451569 451570 451518 452521 452382 053711 053719 053794 053737 053735 051707 051585 051605 053330 052692 051729 051798-01 051813 051737 053734 053739 053352 053500 055139 055127 055597 133118 452408 056952 056946 056013 56161 DESCRIPTION SAW FILTER OFW K3953M SER.FILTER TPS6.0MB COIL 1UH K LAL03 SER.FILTER MKT40.4MA110P-TF SAW FILTER OFW G9353M SER.FILTER MKT40.4MA110P-TF IC-CHIP TDA9563H/N1/3 IC-CHIP TDA9565H/N1/3 IC-CHIP TDA9555H/N1/1I (32K IC-CHIP TDA9563/H/N1/I/4 IC-CHIP TDA9565/H/N1/I/4 IC 4053B CMOS 16SOIC IC MSP3400G IC MSP3410G PSDIP64 AUDIO P IC MSP3411G IC L78L05 ACZ TR IC TDA7262 PWR AMP SGS THOM IC TDA7263 IC-CHIP M24C08-WMN6 (EEPROM IC TDA8359 J IC MC44608P40 IC TDB7805CT T0220CASE IC KA317TU T0220CASE INSULATER BUZ90 17*12*.15 IC TDA6108JF IC-CHIP TDA9886T/V3 118(SO24) IC-CHIP SDA9489X SOP28 IC KA317TU T0220CASE IR RECEIVER TSOP 1838 IC-CHIP S3C1840DA9/SMB1 COIL 10UH K (TAIYO) LAL03 COIL CHIP 1UH COIL CHIP 330NH /0805 COIL-CHIP 8.2UH K /1206 COIL-CHIP 18UH K /12 COIL 6MH E/W 11.1 COIL H-LIN 70UH COIL H.LINEARITE 39UH COIL H.LINEARITE 45UH COIL LINEARITY 30UH (TERMAL BRIDGE COIL 1.5MH BRIDGE COIL 1.8MH BRIDGE COIL 850UH LINE FILTRE 2*18MH E-TYPE COIL 4.7UH LAL03 COIL CHOKE 50UH COIL- CHOKE 10UH R0814 14.1 BOBIN 10UH K AXIAL LAL04 CHOKE COIL 50MHZ 600R PH-WB CORE FERRIT FERRITE BEAD 12*8 R-VAR 10K V(2.5MM) 5*3 IC PC123FY2PHOTO COUPLER CRYSTAL 18.432MHZ +-30PPM CRYSTAL 12MHZ CRYSTAL 4 MHZ CRYSTAL 20.25MHZ PIP PIP P601 PH601 Q301 Q401 Q801 Q802 PIP 21" PF 25",29" 28" 16/9 28" 4/3, 32", 33" 25",28"4/3,33" 28"16/9,32" 29" PIP PIP PIP 33" NON VIRTUAL DOLBY NON VIRTUAL DOLBY, NICAM VIRTUAL DOLBY DK DK LL' BG,I (STEREO INTERCARRIER) BG/DK, LL' (STEREO QSS) MONO QSS PIP (INTERCARIER) PIP (QSS) PIP PI NOTES F801 F104 F105 F105 F106 F108 IC101 IC101 IC101 IC101 IC101 IC102 IC301 IC301 IC301 IC302 IC304 IC304 IC401 IC501 IC601 IC602 IC603 IC603 IC701 IC801 IC802 IC803 IC901 IC980 L101 L102 L102 L104 L201 L501 L502 L502 L502 L502 L503 L503 L503 L601 L603 L604 L701 L801 L962 L803 L963 L303 L301 L105 L302 L106 L401 L402 IC604 POSITION NUMBERS
PARTS LIST
PART NO 056210 172335 172683 171471 174151 174473 173154 174104 101683 172274 173392 171393 172273 173479 171182 179001 171150 171102 171221 173273 171332 179001 172333 170750 171334 172101 171104 172335 173104 172123 171821 170473 129150 119104 179002 170332 170390 170101 172474 172475 170472 171471 120234 110270 174180 173333 173276 114110 121182 109472 114151 119476 119271 119271 119181 119220 119221 129395 129395 119476 DESCRIPTION CER.RESONATOR GSB455E RC-CHIP 3.3K J 1/10W /0805 RC-CHIP 6.8K J 1/10W /0805 RC-CHIP 470R J 1/10W /0805 RC-CHIP 150K J 1/10W /0805 RC-CHIP 470K J 1/10W /0805 RC-CHIP 15K J 1/10W /0805 RC-CHIP 100K J 1/10W /0805 CFR 680R J 1/4W /6 52MM RC-CHIP 2.7K J 1/8W/1206 (T RC-CHIP 39K %1 1/10W/0805 RC-CHIP 390R J 1/10W /0805 RC-CHIP 2.7K J 1/10W /0805 RC-CHIP 47K J 1/10W /0805 RC-CHIP 180R J 1/10W /0805 RC-CHIP 0R /0805 2*1.25 RC-CHIP 150R J 1/10W /0805 RC-CHIP 100R J 1/10W /0805 RC-CHIP 220R J 1/10W /0805 CFR-CHIP 27K J 1/10W /0805 RC-CHIP 330R J 1/10W /0805 RC-CHIP 0R /0805 2*1.25 RC-CHIP 3.3K J 1/8W /1206 RC-CHIP 75R J 1/10W /0805 RC-CHIP 330R J 1/8W /1206 RC-CHIP 1K J 1/10W /0805 CFR-CHIP 100R J 1/8W /1206 RC-CIHP 3.3K J 1/10W /0805 RC-CHIP 10K J 1/8W /1206 RC-CHIP 1.2K J 1/8W /1206 RC-CHIP 820R J 1/8W /1206 CFR-CHIP 47R J 1/8W /1206 RWF 1.5R J 1.5W RWF 1R J 1.5W (UFLB) 73MM RC-CHIP 0R /1206 RC-CHIP 33R J 1/10W /0805 RC-CHIP 39R J 1/8W /1206 RC-CHIP 10R J 1/10W /0805 RC-CHIP 4.7K J 1/8W /1206 RC-CHIP 4.7K J 1/10W /0805 RC-CHIP 47R J 1/10W /0805 RC-CHIP 470R J 1/10W /0805 RMF 22R J 1/2W RMF 27R J .75W 52MM RC-CHIP 180K J 1/10W /0805 RC-CHIP 33K J 1/10W /0805 RC-CHIP 27K J 1/8W /1206 RM 100K %1 1/4W 26MM RW 180R J 2W 73MM CFR 0.47R J 1/2W /9 52MM RM 150K J 1/2W RMF 4.7R J 1W RM 2.7R J 1/2W RM 2.7R J 1/2W RMF 1.8R J 1W 52MM RM 2.2R J 1/2W RM 2.2R J 1W RMF 3.9R J 0.5W 52MM RMF 3.9R J 0.5W 52MM RMF 4.7R J 1W 28"4/3 28" 4/3 28"16/9 21" 32" 21",25",28" 16/9, 29",32",33" 25" 21", 25", 28" 4/3, 33" 21",25",28",29",32" 33" MONO SOUND MONO SOUND MONO SOUND MONO SOUND MONO SOUND MONO SOUND MONO SOUND NOTES Q980 R103 R107 R104 R109 R110 R112 R114 R124 R126 R127 R129 R130 R139 R147 R149 R154 R158 R164 R165 R170 R176 R201 R209 R214 R216 R220 R314 R317 R326 R328 R329 R341 R341 R342 R401 R404 R421 R434 R435 R437 R439 R503 R503 R504 R505 R506 R508 R510 R513 R514 R516 R518 R518 R518 R519 R519 R519 R519 R519 R527 R517 R527 R519 R519 R102 R440 R438 R218 R228 R412 R425 R151 C336 R213 R215 R217 R221 R310 R633 R330 R332 R162 R105 R429 R142 R163 R106 POSITION NUMBERS
PARTS LIST
PART NO 111224 119480 129471 122114 113113 119152 119184 129475 129109 103116 119684 119122 119155 119110 129109 113335 154216 154225 154234 112393 119336 111101 113681 115470 102105 119109 100473 110476 113475 173101 172273 114115 114152 112131 111391 172105 111241 100154 103273 103475 102159 102166 054261 054280 054263 054264 010760 031251 010861 010712-03 010971 010840-01 010840-01 010845 010844 401141 401141 401142 DESCRIPTION RMO 220R J 1W RM 0.47R J 1/2W RF 4.7R J 0.25W 52MM RWF 1K J 1.5W 73MM RMF 10K J 1/2W RMO 1.5R J 2W RMO 1.8R K 3W R:20 RW 4.7R J 7W (YATIK) RWF 0.1R J 0.75W 73MM CFR 10K J 1/4W /6 52MM RMF 0.68R J 1W RMF 1.2R J 1W RMF 1.5R J 1W RMF 1R J 1W RWF 0.1R J 0.75W 73MM RMO 33K J 1W NTC 5.1R M (S234R) PTC 18R/3 PIN PTC 9R/2 PIN - 3CYCLE RM 3.9K %1 1/4W 52MM RM 0.33R %1 1W RMO 1K J 1W RMO 68K J 2W RM 4.7M J 1/2W 52MM CFR 1K J 1/2W /6 52MM RNF 0.1R J 0.4W (UFLB) 52MM CFR 47R J 1/4W /6 52MM RMO 47R J 3W RMO 47K J 1W RC-CHIP 10K J 1/10W /0805 RC-CHIP 2.7K J 1/10W /0805 RM 115K %1 1/4W RM 150K F 1/4W 52MM RM 1.3K %1 1/4W 26MM RM 390R %1 1/4W 26MM RC-CHIP 1K J 1/8W /1206 RM 240R %1 1/4W 26MM CFR 15R J 1/2W 52MM CFR 27K J 1/4W /6 52MM CFR 47K J 1/4W /6 52MM CFR 1.5K J 1/2W /9 52MM CFR 1.5K J 1/4W /6 26MM FUSE 2.5AT (215 SER.) FUSE 3.15AT (215) FUSE T2A FUSE T4A SLIDE SWITCH 4P2P/4PST SCART SOCKET 14.1 ON/OFF SWITCH BK98 POWER SWITCH S40 4/100A-250 MAIN SWITCH GDE S40 4/100ATACT SW LONG STEN 2LEG TACT SW LONG STEN 2LEG TACT SW WITH GREEN LED TACT SWITCH 2 LEG (MTSB) TRN-CHIP BC848B SOT23 TRN-CHIP BC848B SOT23 TRN-CHIP BC858B SOT23 25" 28",29",32" 33" 33" 28" 32" 29" 25" MONO SOUND 32" 29" PAL I 32" PS 29" HHOP U44 EXT.SPEAK. 21", 28" 16:9, 29", 32" 25, 28" 4/3, 33" 28"16/9, 29",33" 21" 25" 28" 16/9 21", 32", 33" 28" 4/3 29" 29" 21" 21", 25" NOTES R520 R521 R522 R523 R524 R525 R525 R525 R526 R528 R529 R529 R529 R529 R529 R531 R601 R602 R602 R605 R607 R608 R609 R610 R611 R612 R617 R618 R621 R622 R623 R625 R625 R627 R628 R630 R631 R639 R645 R705 R711 R903 S601 S601 S602 S603 S960 SK202 SW601 SW601 SW601 SW901 SW901 SW901 SW901 T101 T103 T301 SW902 SW902 SW902 SW902 T102 T104 T302 T105 T303 T106 T305 T308 SK201 R713 R715 R716 R236 R632 R629 R626 R333 R606 R607 POSITION NUMBERS
PARTS LIST
PART NO 400989 401141 401279 401218 401215 401216-02 401047 401142 401141 410026 051709 057138-EL1 057834-TR2 058934-TR1 057534-EL2 057334-EL1 059138-EL1 059834-TR1 059934-TR1 059534-TR1 059834-TR1 059334-TR1 051805 7RZ136-PH3 S99136-PH1 7RZ136-PH4 031866 031035 031854 031858 031780 031872 031856 031794 031821 031675 031727 031882 031530-01 031530-02 031541 031413 31323 031165 031164 031163 031784 031423 031357 031021 031020 303826 302782 303771 451885-01 303799 TRN BC558B TRN-CHIP BC848B SOT23 TRN 2SK2381 TRN BC618 TRN BU508DF TRN 2SK2545 TRN BC337-25 TRN-CHIP BC858B SOT23 TRN-CHIP BC848B SOT23 THRYSTOR MCR22-8 DRIVER TRANSFORMER 11.1 FBT 21" 14:2 FBT 28" 16:9 14.1 FBT 29" 14.1 (C-TYPE) FBT 2528 14.1 FBT 33' 14.1 SMPS 21" 14.2 P.FLAT SMPS 28" 16:9/SLOT TR/..... SMPS 29" 14.1 SMPS 2528 14.1 SMPS 28" 16:9 14.1 SMPS 33" 14.1 COIL PFC 56MH DTH30563H ELI TUNER PH ASIMETRIK UV1316/A TUNER PH SPL ASIMETRIK UV1316 T TUNER PH ASIMET. UV1316/ALG-3 SV22 CONN.HOUSING X2006 GREY PIN HEADETR 2.5MM 7.PC.MOLE CONN.HOUSING X2003 GREY CONN.HOUSING X2004 GREY CONN.HOUSING 2'LI GREY CONN.HOUSING X2007 BLACK CONN.HOUSING X2003 BLACK CONN.MALE HOR. 4.PIN PLUG CON.HOUSING X2.5TMK 2204 GR CON.HOUSING 2P MALE CON.MALE. 2.5TMK 2009S CON.MALE X2.5TMK 2010G INCHANG/CRT SOCKET ISHM05SINCHANG/CRT SOCKET ISHM23SCRT SOCKET 29" DOUBLE FOCUS CONN.FEMALE 9 PIN CON.MKF19400-6-0-1010 KONN. CINCH ........... YEL KONN. CINCH ........... RED KONN. CINCH ........ WHITE KONN.S-VHS B10B MONAKOR HEADPHONE JACK YKB21-5103 CON.HOUSING X2.5TMK 2904 G PIN HEADETR 2.54MM 3.PC.MOL PIN HEADETR 2.54MM 4.PC.MOL DIODE Z. BZX55C 15V DOIDE Z. MTZJ18B DIODE Z. UZT33V IC TL431CLP (ON SEMICONDUCT D- ZENER MTZJ12B 21" Pure Flat EXT. SPEA. 29" 32" 29" 32" SVHS SVHS SVHS SVHS PIP PIP Non Pure Flat 21" Pure Flat Pure Flat LL' PIP PIP 21" PF 28" 16:9 29" 25", 28"4/3 33" 21" 32" 29" 25", 28" 28" 16:9 33" T980 T603 TH601 TR501 TR502 TR502 TR502 TR502 TR502 TR601 TR601 TR601 TR601 TR601 TR601 TR602 TU101 TU101 TU201 X102 X104 X301 X302 X303 X403 X404 X502 X503 X601 X662 X663 X703 X703 X703 X801 X802 X921 X922 X923 X924 X941 X962 X964 X965 ZD501 ZD501 ZD502 ZD602 ZD603 X602 X604 X605 X405 X402 X501 X940 T604 DESCRIPTION NOTES T306 T307 T501 T503 T504 T601 POSITION NUMBERS T309 T403
PARTS LIST
PART NO 300193 S99170 056321-PH7 056325-VC4 056428-SB1 056428-PS1 056328-VC6 056329-SB1 056329-VC2 056432-PS2 056432-VC2 056333-VC3 525167-AS 628167-AS 528166-AS 621167-AS 528169-AS 629167-AS 532168-AS 532169-AS 533167-AS 7P3187 6VM187 7UK187 7TK187 7PE187 5T1187 7UB109-AS 7UB107-AS 6X1107-AS 7UB108-AS 7VA108-AS DESCRIPTION DIODE Z. BZX55C9V1-GPS(VISH PIP MODULE KPL.14.2 CPT PH A51ERF135*70 P.FLAT CPT VC A59EHJ13X38 CPT SEB W66QDE893X286 (P.FLAT) CPT PS W66EHK51X36 CPT VC A66EHJ13X62 CPT SEB A68QCP891X404 CPT VC A68EGD049X30 (S.FLAT CPT PS W76EKW10X21 P.FLAT CPT VC W76EGV023X015 S FLAT CPT VC A80AEJ15X04 DEGAUSSING COIL ASSY 25" BA DEGAUSSING COIL ASSY 28" BA DEGAUSSING COIL ASSY DEGAUSSING COIL ASSY 21" BA DEGAUSSING COIL ASSY DEGAUSSING COIL 29" DEGAUSSING COIL ASSY DEGAUSSING COIL ASSY DEGAUSSING COIL 33" RC A TYPE PRINTED SIL RC A TYPE SILVER 14.1 RC A TYPE GREY 14.1 RC B TYPE FUME 14.1 RC B TYPE M.GREY 14.1 RC B TYPE SILV.14.1 SPE.SUB 4R/20W(NOM)21T04/25 SPEAKER 8R/15W(MAX)21T04/25 SPK.8R/15W(MAX) 32"T20/T21 TWEETER 10R/10W(N)21T04/25T TWEETER DYNAMIC D=52 8R/15W 29" 29" EXT.SPEAK. 29" 33" PIP 21" Pure Flat 25" 28"16/9 Pure Flat 28"16/9 Super Flat 28"4/3 29" Pure Flat 29" Super Flat 32" Pure Flat 32" Super Flat 33" 25" 28"4/3 28"16/9 Pure Flat 21" Pure Flat 28"16/9 Super Flat 29" 32" Pure Flat 32" Super Flat 33" NOTES ZD606 POSITION NUMBERS
Please note that Product Part List Files should be investigated for the mechanical parts like cabinets, etc.
PIP MODUL (PICTURE IN PICTURE OPTIONAL)
C846 R843 330R 470nF GND4
GND
+5V R846 47K R844 C847 330pF 680R C849 T806 BC848B CVBSIN3 CVBSIN2 R850 330R CVBSIN1 R859 0R OPT R847 33K R849 1K 470nF T807 BC858B R853 47K R854 47K R848 1K
+5V +5V C850 47nF
IC803 IN
LM317 OUT ADJ +3.3V R856 240R R857 390R C851 47nF C852 33nF +3.3V
CVBSsc2/Y
TU202 TUNER 15
CVBSINSC2
GND3 GND2 GND1 CHROMAIN CHROMA 47nF C829 Q802 1 XIN IC801 27pF 2 XQ 20.25 MHz R823 C827 3 100pF 4 HSP CVBS2 26 4 1 C802 HSYNC 2 VIF2 5 3 OP1
+3.3V +5V
14 13 12 R845 6K2 C848
AGC
TUNE
AS
SCL
SDA
NC
5V
ADC
33V
IFIN1
1
2
3
4
5
6
7
8
9
IFIN2
10
11
IC802 CVBS1 28 R824 75R VREFM 27 C831 1uF 25 VSP C826 100pF 5 100R R821 100R R820 VREFL C834 SDA 6 CVBS3 24 1uF 23 C835 10nF C836 SCL 100R C824 C825 10uF 16V 10nF 7 VSSA1 220nF R826 75R C837 VDD 8 VDDA1 22 1uF VSS 9 VREFH 21 C840 I2C VSSA2 20 10uF C839 1uF 10nF L804 10uH +5V C838 10nF R855 1R +3.3V C832 10nF C833 220nF
F801 K3953M 1 VIF1 T808 BC848B C828 27pF R852 330R R851 1K VSYNC +5V SDA L803 10uH SCL C814 C817 10uF R812 10nF 23 SIF2 24
C830 220nF
C801 47pF SIF1 22 2 SCL OP2 21 +5V C811 5 10nF DEEM C815 220nF 19 R811 330R T801 BC848 Vp 6 AFD VPLL 10nF 7 DGND 17 C818 C819 470nF 10 SDA 22pF 11 SCL 13 C821 10nF 13 IN3 14 C820 22nF R814 75R R815 75R R816 75R R817 75R TAGC 14 4.43 MHz REF 15 C823 10nF C822 10nF 11 IN1 12 Q801 AGND
+5V
R801
R802
SCL
47pF 100R R822
X801
SDA
100R
100R
9 SDA
3
8 4 C813 C812 390pF 20 10nF R810 5K6 C810 C803 4.7uF 8 AUD 16 R813 75R 220R CVBS 100pF 18 C816 1.5nF C804 FMPLL AFC
R825 75R
7
6
VSYNC
5
HSYNC
4
+33V
R803
+33V
+5V
3
L801
1K
+5VTUNER
10uH
2
CVBSsc2/Y
C806
C807
R819 4K7
1 R860 47K 9 TOP VAGC R809 100R R808 100R 12 SIOMAD TDA9886 R807 680R R805 33K n.c. R861 47K
CHROMA
C805 100uF 16V
10nF
100pF
PIP_9
R818 0R 10 INT VDDA2 19 C841 C842
10nF C843 OUT1 18 100uF 16V IN2 OUT2 17 C844 16 OUT3 100uF 16V C845 FSW SDA9489X
R831
R828 10K
R829 10K
R827 10K T802
R804 3K9
BC848
T803
BC848 15 SEL +5V 100uF 16V
10K 220R 10K 220R
T804
D801
1N4148
R832
R833
R834
R835
1 CVBS1_out
1K R837 R838 75R R839 75R R842 75R R841 1K R840 220R 75R
2
Rpip
3
Gpip
4
Bpip
5
CVBSsc1
6
Rsc1
7
Gsc1
8
Bsc1
9
FBLpip
10
FBLsc1
PIP_10
R836
X802
47uF 16V
220R
1nF
R806 12K
R830
T805 BC848
10K
C808
BC848
C809