Text preview for : SyncMaster 470STFT.pdf part of Samsung SyncMaster 470STFT COLOR MONITOR TFT SyncMaster 470STFT (RN14AS)



Back to : SyncMaster 470STFT.rar | Home

COLOR MONITOR
SyncMaster 470STFT
(RN14AS)

SERVICE
COLOR MONITOR

Manual
CONTENTS
1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Troubleshooting 5. Exploded View & Parts List 6. Electrical Parts List 7. Block Diagram

AUTO

EXIT

MENU

8. Wiring Diagram 9. Schematic Diagrams

1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock.

1-1 Safety Precautions
1-1-1 Warnings
1. 2. 3. For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC Power Jack before servicing. When the chassis is operating, semiconductor heatsinks are potential shock hazards.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES (READING SHOULD NOT BE ABOVE 0.5mA)

LEAKAGE CURRENT TESTER

1-1-2 Servicing the LCD Monitor
1. When servicing the LCD Monitor, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead. (Disconnect the AC line cord from the AC outlet.) It is essential that service technicians have an accurate voltage meter available at all times. Check the calibration of this meter periodically.

2-WIRE CORD

ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)

EARTH GROUND

2.

Figure 1-1. Leakage Current Test Circuit
4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.

1-1-3 Fire and Shock Hazard
Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

2.

1-1-4 Product Safety Notices
Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by ! on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate.

3.

SyncMaster 470STFT

1-1

1 Precautions

1-2 Servicing Precautions
WARNING: Caution: Note: An electrolytic capacitor installed with the wrong polarity might explode. Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.

1-2-1 General Servicing Precautions
1. Always unplug the unit's AC power cord from the AC power source and disconnect the DC Power Jack before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect a test component in parallel with an electrolytic capacitor. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged. 4. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 6. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.

5.

2.

3.

1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs. Use only a grounded-tip soldering iron to solder or desolder ESDs. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESDs. 8. 6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

7.

2.

3.

Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.
Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.

4. 5.

1-2

SyncMaster 470STFT

2 Product Specifications
2-1 Specifications
Item LCD Panel Scanning Frequency Display Colors Maximum Resolution Input Video Signal Input Sync Signal Description TFT-LCD panel, RGB vertical stripe, normaly white, 14-Inch viewable, 0.27825 (H) x 0.27825 (V) pixel pitch Horizontal Vertical 262,144 colors Horizontal Vertical : : 1024 Pixels 768 Pixels : : 30 kHz to 61 kHz (Automatic) 50 Hz to 75 Hz (Automatic)

Analog, 0.714 Vp-p ± 5% positive at 75 , internally terminated Type:Seperate H/V sync, Composite H/V, Sync-on-Green, automatic synchronization without external switch of sync type Level: TTL level 80 MHz 284.9 mm / 213.7 mm AC 90 to 264 Volts, 60/ 50 Hz to 12V/3A 35W (max.)

Maximum Pixel Clock rate Active Display Horizontal/Vertical AC power voltage & Frequency Power Consumption Dimensions / Unit Weight / incl.Carton Unit (W x H x D) with: Simple base MultiMedia base Pivot-MM base Angle-Pivot base Wire-frame base Carton (W x H x D) Environmental Considerations

375.4 x 361.7 x 168 mm / 5.15kg / 8.35kg 375.4 x 403.2 x 174 mm / 5.9kg / 9.1kg 375.4 x 403.2 x 174 mm / 5.9kg / 9.1kg 375.4 x 428.6 x 173.9 mm / 6.55kg /9.75kg 375.4 x 336.2 x 92.7 mm / 4.35kg / 7.55kg 415 x 282 x 510 mm Operating Temperature : Humidity : 10 % to 80 % Storage Temperature : Humidity : 5 % to 95 % 50°F to 104°F (10°C to 40°C) -13°F to 113°F (-25°C to 45°C)

Audio Characteristics

· Audio Characteristics · Built-in Microphone: High-sensitivity condenser microphone (mono) · Audio input: Left/Right Stereo phone jack, 0.5 Vrms · Sound output: 1.0 W (left) + 1.0 W (right)/THD 1% at 8ohm · Frequency response: 80 Hz~20 kHz (at ­3dB) · Headphone: Max 50mW output (3.5-pi jack) · Speaker: Internal semi Dome (16ohm x 2)

·SyncMaster 470STFT comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields. ·Designs and specifications are subject to change without prior notice.

SyncMaster 470STFT

2-1

2 Product Specifications

2-2 Pin Assignments
Sync Type Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Separate Red Green Blue GND GND (DDC Return) GND-R GND-G GND-B No Connection GND-Sync/Self Test GND DDC Data H-Sync V-Sync DDC Clock 15-Pin Signal Cable Connector Composite Red Green Blue GND GND (DDC Return) GND-R GND-G GND-B No Connection GND-Sync/Self Test GND DDC Data H/V-Sync Not Used DDC Clock Sync-on-green Red Green + H/V Sync Blue GND GND (DDC Return) GND-R GND-G GND-B Not Used GND-Sync/Self Test GND DDC Data Not Used Not Used DDC Clock

2-2

SyncMaster 470STFT

2 Product Specifications

2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Mode VGA1/70 Hz 640 x 350 31.469 31.778 3.813 1.589 26.058 0.318 70.086 14.268 0.064 1.716 11.504 0.985 25.175 IBM VGA2/70 Hz 720 x 400 31.469 31.777 3.813 1.589 26.058 0.318 70.087 14.268 0.064 0.858 13.155 0.191 28.322 VGA3/60 Hz 640 x 480 31.469 31.778 3.813 1.589 26.058 0.318 59.940 16.683 0.064 0.794 15.761 0.064 25.175 640/72 Hz 640 x 480 37.861 26.413 1.270 3.810 20.825 0.508 72.809 13.735 0.079 0.528 13.100 0.026 31.500 VESA 640/75 Hz 640 x 480 37.500 26.667 2.032 3.810 20.317 0.508 75.000 13.333 0.080 0.427 12.800 0.027 31.500 800/56 Hz 800 x 600 35.156 28.444 2.000 3.556 22.222 0.667 56.250 17.778 0.057 0.626 17.067 0.028 36.000 800/60 Hz 800 x 600 37.879 26.400 3.200 2.200 20.000 1.000 60.317 16.579 0.106 0.607 15.840 0.026 40.000

Timing fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock Frequency (MHz) Polarity H.Sync V.Sync Remark

Positive Negative Separate

Negative Positive Separate

Negative Negative Separate

Negative Negative Separate

Negative Negative Separate

Positive Negative Separate

Positive Positive Separate

Separate Sync
Horizontal
Video Video
CC

Vertical
Video Video DD E E
Q

Q

RR

S S

Sync Sync B B AA

Sync Sync

PP
O O

A : Line time total C : Back porch E : Front porch SyncMaster 470STFT

B : Horizontal sync width D : Active time

O : Frame time total Q : Back porch S : Front porch

P : Vertical sync width R : Active time

2-3

2 Product Specifications

Table 2-1. Timing Chart Continued Mode 800/72 Hz 800 x 600 48.077 20.800 2.400 1.280 16.000 1.120 72.188 13.853 0.125 0.478 12.480 0.770 50.000 800/75 Hz 800 x 600 46.875 21.333 1.616 3.232 16.162 0.323 75.000 13.333 0.064 0.448 12.800 0.021 49.500 VESA 1024/60 Hz 1024 x 768 48.363 20.677 2.092 2.462 15.754 0.369 60.004 16.666 0.124 0.600 15.880 0.062 65.000 1024/70 Hz 1024 x 768 56.476 17.707 1.813 1.920 13.653 0.320 70.069 14.272 0.106 0.513 13.599 0.053 75.000 1024/75 Hz 1024 x 768 60.023 16.660 1.219 2.235 13.003 0.203 75.029 13.328 0.050 0.466 12.795 0.017 78.750 MAC. 640/67 Hz 640 x 480 35.000 28.571 2.116 3.175 21.164 2.116 66.667 15.000 0.086 1.114 13.714 0.086 30.240 832/75 Hz 832 x 624 49.726 20.110 1.117 3.910 14.524 0.559 74.551 13.414 0.060 0.784 12.549 0.020 57.284

Timing fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock Frequency (MHz) Polarity H.Sync V.Sync Remark

Positive Positive Separate

Positive Positive Separate

Negative Negative Separate

Negative Negative Separate

Positive Positive Separate

Negative Negative Separate

Negative Negative Separate

Separate Sync
Horizontal
Video Video
CC

Vertical
Video Video DD E E
Q

Q

RR

S S

Sync Sync B B AA

Sync Sync

PP
O O

A : Line time total C : Back porch E : Front porch

B : Horizontal sync width D : Active time

O : Frame time total Q : Back porch S : Front porch

P : Vertical sync width R : Active time

2-4

SyncMaster 470STFT

3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the SyncMaster 470STFT monitor. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components.

3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly. 2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

3-1-1 Removing the Stand
1. Remove 4 screws in the hinge area. 2. Pry it off the back of the monitor. 3. Disconnect Power Cord and Signal Cable.

4. Remove the 4 screws. 5. Disconnect CN805, CN806, CN807, CN808, CN809, CN812 and F1. 6. Remove the Back Cover of the Stand Front assembly. 7. Remove 4 screws on the external adaptor and remove the adaptor. 8. Remove 2 screws between hinge and Stand Body. 9. Remove the hinge 10. Remove 2 screws on Audio main PCB and remove it 11. Remove 2 screws on the Audio Function PCB and remove it.

3-1-2 Main Body Disassembly
1. Remove the 4 screws on the four corner of the Rear Cover. 2. Remove Rear Cover from the Front Cover. 3. Remove 11 screws on the Shield and remove the shield. 4. Disconnect Inverter wire, Function PCB wire and Interface wire. Remove 4 screws on the Main PCB and remove 2 screws on the D sub shield. 5. Remove the Main PCB Assembly. 6. Remove 6 screws on the Rear Panel Bracket. 7. Remove the Bracket Assembly from the Front Cover. 8. Remove 3 screws on the Function PCB from locking area of Function knob and remove Function PCB. 9. Remove 4 screws on the Shield of Panel. 10. Remove the Shield. 11. Remove Rear Bracket from Panel. 12. Remove 2 screws between Panel Rear and Inverter PCB. 13. Remove the Interface wire on the Rear Side of Panel.

3-1-4 Multi-media Stand Disassembly (Multi-media pivot stand Disassembly) Pivot Stand Disassembly
1. Remove the cap pivot from the stand assembly. 2. Remove the 4 screws on the hinge assembly. 3. Remove the 4 screws on the Stand Rear 4. Remove the Stand Rear from the Stand assembly. 5. Remove the Stand Front from the Stand assembly. 6. Remove the Neck Rear from the Stand assembly. 7. Remove the 4 Rubbers on the four corner of the Stand Bottom and the 4 screws on the four corner of the Stand Bottom.

3-1-3 Multi-media Stand Disassembly (option)
1. Stand the stand assembly with the base close to you. 2. Remove the 4 screws on the back cover of the stand and remove it. 3. Stand the stand assembly upside down. SyncMaster 470STFT

8. Remove the 5 stopper hings from the Bracket Bottom. 9. Remove the Stand Base from the Stand Assembly.

3-1-5 Standard Stand Disassembly
1. Remove 5 screws from the Stand Rear 3-1

3 Disassembly and Reassembly 2. Remove 4 screws from the Stand Bottom. 3. Remove Stand Front from the Stand assembly. 4. Remove 2 screws from the Stand assembly. 5. Remove the Stand Rear from the Stand assembly. 6. Remove 5 screws on the Vesa Brkt from the Stand assembly. 7. Remove cover hinge from the Stand assembly. 8. Remove Stand Base from the Stand assembly.

3-1-5 Wire frame stand Disassembly
1. Carefully pull the cover hinge. 2. Remove the cover vesa from the Stand assembly. 3. Remove 4 screws on the assembly Bracket assembly.

3-2 Replacement Order of Lamp Assemblies
1. Disconnect lamp leadconnectors from the inverter. (2EA) * Replacement of lamp assemblies should be done at the power off state and recommended clean bench condition.

2. Remove 2 screws which are used to hold the lamp assemblies on. 3. Replace 2 lamp assemblies. 4. Assemble new lamp assemblies according to the counter order.

3-3 Reassembly
Reassembly procedures are in the reverse order of Disassembly procedures.

3-2

SyncMaster 470STFT

4 Troubleshooting
Notes: 1. Before troubleshooting, setup the PC's display as below. · Resolution: 1024 x 768 · H-frequency: 48 kHz · V-frequency: 60 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. · No raster appears: Audio PCB, SMPS PCB, Main PCB · 12V develop but no screen: Main PCB · 12V does not develop: Audio PCB, SMPS PCB 4. If you push and hold the "EXIT" button for more than 5 seconds, the monitor automatically turns back to the factory preset.

4-1 No Power
Does proper DC 12 V appear at DC jack connected to CN101? No Check SMPS or CN809.

Yes

Does proper DC 5 V appear at Pin 4 of IC101?

No

Check FT104 and IC101.

Yes

Check IC102, IC103, IC104 or IC901.

SyncMaster 470STFT

4-1

4 Troubleshooting

4-2 No Video
Power indicator is green

Does the clock pulse appear at Pin 81, 83 and 84 of IC201?

No

5

Does the H-sync pulse appear at Pin 94 of IC201?

No

6

7

Does the pulse appear at Pin 9 of IC106 or Pin 1 of IC105? Yes

No

Yes Yes Replace IC201.

Replace IC106. Replace IC104 (SOG) or check R102 and Pin 13 of CN201 No Check IC201 and IC401.

9

10

Does the sync pulses appear at Pins 20 and 22 of IC303?

No

11

1

Does the sync pulses appear at Pins 34 and 39 of IC303? Yes

Yes

Replace IC303 or check its related circuit.

2

3

Do the sync pulses appear at Pins 25 and 26 of IC304?

No

8

Do the sync pulses appear at Pins 141 and 142 of IC301? Yes

No

Replace IC301 or check its related circuit.

Yes

Replace IC304 and IC305 or check its related circuit. No Replace IC304 and IC305 or check its related circuits.

4

Do the waveforms appear at Pins 1 and 16 of CN301? Yes Replace LCD Panel

4-2

SyncMaster 470STFT

4 Troubleshooting

WAVEFORMS
1 IC303 #39 2 IC304 #25 3 IC304 #26 4 CN301 #1~16

CH1 RMS = 3.6 V

CH1 RMS = 2.8 V

CH1 RMS = 2.12 V

CH1 RMS = 1.18 V

5 IC201 #94

6 IC106 #9

7 IC105, #1

8 IC301 #141

CH1 RMS = 3.5 V

CH1 RMS = 3.1 V

CH1 RMS = 4.56 V

CH1 RMS = 2.3 V

9 IC303 #20

10 IC303 #22

11 IC303 #34

CH1 RMS = 1.24 V

CH1 RMS = 400 mV

CH1 RMS = 4.4 V

SyncMaster 470STFT

4-3

4 Troubleshooting

4-3 No Video of Alternate Vertical Line
One or more even or odd vertical lines do not display.

4

Does the waveform appear at Pin 10 or Pin 2 of CN301? Yes Replace LCD panel.

No

Replace IC304 or IC305 or check its related circuit.

WAVEFORMS
4 CN301 #20

CH1 RMS = 1.18 V

4-4 No OSD
WAVEFORMS
There is video but no OSD.
12 IC302 #12

12

While pushing a front control button does any pulse appear at Pin 12 of IC302? Yes Replace IC302.

No

13

Do sync signals appear at Pins 5 and 10 of IC302? 14 Yes Replace IC302 or check its related circuit. Replace IC301.

No
CH1 RMS = 2.2 V

13 IC302 #5

CH1 RMS = 1.7 V

14 IC302 #10

CH1 RMS = 4.3 V

4-5 User Controls Don't Work
Does the DC level change at Pins 13 and 14 of IC401 when you push the front panel button? Yes Go to 4-4 No OSD Display. 4-4 SyncMaster 470STFT

No

Check the buttons. (SW801 ~ SW808)

4 Troubleshooting

4-6 No Sound

Does the DC 12 V appear at Pin 2 of IC801, Pin 6 of CN801? Yes Does the sound input signal appear at Pins 6 and 7 of IC801? Yes Do the sound signals appear at Pins 1 and 3 of IC801? Yes Check CN805, CN806 outputs.

No

Check IC801, VR803 and related circuit.

No

Check Pins 1 and 3 of CN801 and related circuits.

No

Check IC801 and related circuits.

SyncMaster 470STFT

4-5

4 Troubleshooting

4-7 Microphones Don't Work

Does the PC's sound program operate well? Yes Is the connection between the PC and monitor secure? Yes Is the Internal Microphone connector attached? Yes Does the Internal Microphone work? Yes Does the External Microphone work? Yes OK

No

Check the PC's sound program and compatibility.

No

Connect the cable between the PC and monitor.

No

Check the connection between CN808 on the Audio PCB and the Internal Microphone.

No

Check Q801 and related circuits.

No

Check the CN803 jack.

4-8 Headphones Don't Work
Check CN802 on the Audio PCB and related circuit D805, D806, R811, R812.

Can you hear any sound from the Headphones? Yes OK

No

4-6

SyncMaster 470STFT

5 Exploded View and Parts List
5-1 Simple base

5-1

SyncMaster 470STFT

5 Exploded View & Parts List

5-2 MultiMedia base

SyncMaster 470STFT

5-2

6 Electrical Parts List

Loc. No. C137 C138 C139 C140 C141 C142 C143 C144 C145 C146 C147 C148 C149 C150 C151 C152 C153 C154 C155 C156 C157 C158 C159 C160 C161 C162 C163 C164 C201 C202 C203 C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C301 C302 C303 C304 C305

Code No. 2203-000260 2203-000204 2203-000260 2203-000204 2203-000260 2203-000204 2203-000455 2203-001391 2203-000260 2203-000260 2203-000609 2203-000260 2203-000260 2203-000260 2203-000609 2203-000260 2203-000260 2203-000260 2203-000609 2203-000260 2203-000151 2203-000260 2203-000260 2203-000204 2203-000204 2402-000108 2203-000204 2402-000108 2203-000260 2203-000260 2203-000204 2203-000260 2203-000204 2203-000818 2203-000260 2203-000204 2203-000260 2203-000204 2203-000260 2203-000204 2203-000260 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204

Description ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 1nF,5%,50V,NPO,2012,TP ccap, C-CERAMIC,CHIP, 150nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 22nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 22nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 22nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 1.5nF,5%,50V,NPO,TP,2012 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 33pF,5%,50V,NPO,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012

Remarks

6-2

SyncMaster 470STFT

6 Electrical Parts List

Loc. No. C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 C324 C325 C326 C327 C328 C329 C330 C331 C332 C333 C334 C335 C336 C337 C338 C339 C340 C341 C342 C343 C344 C345 C346 C381 C382 C383 C401 C402 C403

Code No. 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000204 2203-000683 2402-000108 2203-000260 2402-000108 2203-000260 2203-000818 2203-000818 2203-000260 2402-000108 2203-000260 2402-000108 2203-000260 2402-000108 2203-000260 2402-000108 2203-000260 2402-000108 2203-000260 2402-000108 2203-000260 2203-000260 2203-000260 2203-000260 2402-000108 2203-000260 2203-000455

Description ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ccap, C-CERAMIC,CHIP, 27pF,5%,50V,NPO,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 33pF,5%,50V,NPO,2012,TP ccap, C-CERAMIC,CHIP, 33pF,5%,50V,NPO,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 1nF,5%,50V,NPO,2012,TP

Remarks

SyncMaster 470STFT

6-3

6 Electrical Parts List

Loc. No. C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C415 C416 C417 C418 C419 C420 C902 CFT301 CL101 CN101 CN201 CN301 CN401 CN402 D101 D102 D103 D104 D201 D401 D402 FT101 FT102 FT103 FT104 FT201 FT202 FT203 FT204 FT301 FT302 FT303 FT304 FT305 FT306 FT307

Code No. 2203-000555 2203-000555 2203-000204 2402-000108 2402-000108 2203-000260 2402-000108 2203-000260 2402-000108 2203-000260 2203-000239 2203-000204 2402-000108 2203-000260 2203-000260 2203-000260 2402-000108 2402-000170 2901-001115 BN27-20001C 3722-000117 3701-001129 3711-003161 3711-002049 3711-000556 0401-001056 0401-001056 0401-001056 0402-000553 0401-001056 0401-001056 0401-001056 2901-001114 2901-001114 2901-001114 3301-001145 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114 2901-001114

Description ccap, C-CERAMIC,CHIP, 20pF,5%,50V,NPO,2012,TP ccap, C-CERAMIC,CHIP, 20pF,5%,50V,NPO,2012,TP ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 100pF,5%,50V,NPO,TP,2012 ccap, C-CERAMIC,CHIP, 100nF,10%,25V,X7R,TP,2012 ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ccap, C-CERAMIC,CHIP, 10nF,10%,50V,X7R,2012,TP ecap, C-AL,SMD, 10uF,20%,16V,WT,TP,4.3x4.3x5.4 ecap, C-AL,SMD, 1uF,20%,50V,GP,4x5.4,1mm,TP filter3p_3, FILTER-EMI SMD, 50VDC,500mADC,20pF,3.1x1.6x2 coil, COIL-SMD, 105UH,20%,SMD,TAPING dcjhp_7, JACK-DC POWER, 3P,3.5mm,AG,BLK,NO tpcon19p, CONNECTOR-DSUB, 15P,3R,FEMALE,ANGLE,AUF slcon22p_1, CONNECTOR-HEADER, BOX,20P,1R,1.25mm,ANGLE,SN slcon8p, CONNECTOR-HEADER, BOX,6P,1R,1.25mm,SMD-A,SN slcon14p_1, CONNECTOR-HEADER, BOX,12P,1R,1.25mm,SMD-A,SN diode_acc, DIODE-SWITCHING, MMBD4148SE,75V,600mA,SOT-23,TP diode_acc, DIODE-SWITCHING, MMBD4148SE,75V,600mA,SOT-23,TP diode_acc, DIODE-SWITCHING, MMBD4148SE,75V,600mA,SOT-23,TP diode_sch, DIODE-RECTIFIER, SS24,40V,2.0A,DO-214AA diode_acc, DIODE-SWITCHING, MMBD4148SE,75V,600mA,SOT-23,TP diode_acc, DIODE-SWITCHING, MMBD4148SE,75V,600mA,SOT-23,TP diode_acc, DIODE-SWITCHING, MMBD4148SE,75V,600mA,SOT-23,TP filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter_smd, CORE-FERRITE BEAD, AB,4.5x1.6x1.6mm filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1 filter3p_1, FILTER-EMI SMD, 25VDC,2.0ADC,100nF,3.2x1.6x1

Remarks

6-4

SyncMaster 470STFT

6 Electrical Parts List

Loc. No. IC101 IC102 IC103 IC104 IC105 IC106 IC107 IC201 IC202 IC301 IC302 IC303 IC304 IC305 IC401 IC401_SOCKET IC402 IC403 IC404 IC901 L101 L103 Q101 Q102 Q103 Q104 Q401 Q402 Q901 Q903 R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 R111 R112 R113 R114 R115 R116 R117

Code No. 1203-001448 0505-001170 1203-001293 1203-001488 1204-000292 0803-000122 1203-001538 1002-001099 0803-000275 BN13-00004A BN09-10001C BN13-00002A 1003-001023 1003-001023 0903-001063 3704-001071 1203-001109 1103-001087 1103-001023 0505-001170 2703-001070 2703-001070 0501-002080 0501-002080 0501-002080 0501-002080 0501-002080 0501-002080 0501-002080 0501-002080 2007-000872 2007-000282 2007-000282 2007-000300 2007-000282 2007-000872 2007-000290 2007-000290 2007-000290 2007-000468 2007-000300 2007-000872 2007-000023 2007-001113 2007-001166 2007-001166 2007-001166

Description lm2596, IC-POSI.FIXED REG., 2596,TO-263,5P,PLASTIC,4.750 si9933, FET-SILICON, SI9933ADY-T1,P,-20V,3.4A,0.075 icreg3p, IC-POSI.FIXED REG., 033,T0-252,3P,6.5MIL,PLASTIC,3 icreg3p, IC-POSI.FIXED REG., 7805,T0-252,3P,PLASTIC,4.8/5 ic_8p_1, IC-VIDEO SYSTEM, IC-VIDEO,LM1881M,SOP,8P,150MIL ic_14p, IC-TTL, 74F125,BUFFER,SOP,14P,150MIL,Q icreg3p, IC-POSI.ADJUST REG., 431,SOT-89,3P,PLASTIC,2.47/3 tda8752, IC-A/D CONVERTER, TDA8752,8BIT,QFP,100P,+-0.5 ic_14p, IC-TTL, 74F32,OR GATE,SOP,14P,150MIL,Q sdp_9801, IC-MEMORY, SDP_9801, 256P, 0.4mm ic_16p, IC-OSD PROCESSOR, LSA820/LSB810,LSC3851DW,16P,EN svsp_d1, IC-ASIC, XB(LCD),FG60A018HM_L18,QFP,48P ic_48p, IC-VFD, DS90CF561,DIP,48P,600MIL,SINGL ic_48p, IC-VFD, DS90CF561,DIP,48P,600MIL,SINGL st72e75, IC-MICROCONTROLLER, 72E75,8BIT,DIP,42P,600MIL,24MH SOCKET-IC;42P,DIP,SN,1.778mm icreg3p, IC-VOL. DETECTOR, 7045,SOT-89,3P,PLASTIC,4.3/4 24lc21, IC-EEPROM, 24LC21A,128X8BIT,DIP,8P,150MIL 24C08,1028*8BIT,SOP,8P,150MIL si9933, FET-SILICON, SI9933ADY-T1,P,-20V,3.4A,0.075 induct2p, INDUCTOR-SMD, 100uH,10%,4.5x3.2x3.2mm induct2p, INDUCTOR-SMD, 100uH,10%,4.5x3.2x3.2mm npn_bec, TR-SMALL SIGNAL, 2SC2412K,NPN,200mW,SOT-23,TP,1 npn_bec, TR-SMALL SIGNAL, 2SC2412K,NPN,200mW,SOT-23,TP,1 npn_bec, TR-SMALL SIGNAL, 2SC2412K,NPN,200mW,SOT-23,TP,1 npn_bec, TR-SMALL SIGNAL, 2SC2412K,NPN,200mW,SOT-23,TP,1 npn_bec, TR-SMALL SIGNAL, 2SC2412K,NPN,200mW,SOT-23,TP,1 npn_bec, TR-SMALL SIGNAL, 2SC2412K,NPN,200mW,SOT-23,TP,1 npn_bec, TR-SMALL SIGNAL, 2SC2412K,NPN,200mW,SOT-23,TP,1 npn_bec, TR-SMALL SIGNAL, 2SC2412K,NPN,200mW,SOT-23,TP,1 res, R-CHIP, 4.7Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 10Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 4.7Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 1Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 10Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 4.7Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 120ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 680Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 75ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 75ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 75ohm,5%,1/10W,DA,TP,2012

Remarks

SyncMaster 470STFT

6-5

6 Electrical Parts List

R118 R119 R120 R121 R201 R202 R203 R204 R205 R206 R207 R209 R211 R213 R301 R302 R303 R304 R400 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R417 R418 R419 R420 R421 R422 R423 R424 R425 R426 R427 R428 R430

2007-000493 2007-000300 2007-000290 2007-001166 2007-000290 2007-000872 2007-000468 2007-000468 2007-000593 2007-000593 2007-000593 2007-000781 2007-000781 2007-000781 2007-000781 2007-000290 2007-000290 2007-000468 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000468 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000290 2007-000941

res, R-CHIP, 2.2Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 10Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 75ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 4.7Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 1Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 1Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 22ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 22ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 22ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 33ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 33ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 33ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 33ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 1Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 1Kohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 100ohm,5%,1/10W,DA,TP,2012 res, R-CHIP, 47Kohm,5%,1/10W,DA,TP,2012

6-6

SyncMaster 470STFT

24
digital R/G/B

36
digital R/G/B

SyncMaster 470STFT

7 Block Diagram

analog R/G/B ADC (TDA8752) Scaler (SDP-9801) LVDS (90CF561)

LVDS

H/V

Sync Proc. (LM1881 & F125)

Micom (ST7275)

OSD & EEPROM (LSC3851) (2408 & 2421)

12V

DC-DC Converter

5V 3.3V 12V

Auto (sVSP-D1)

VOLUME TONE CTRL

TDA2822M (Audio Amp)

SPEAKER SPEAKER

7-1

7 Block Diagrams

Memo

7-2

SyncMaster 470STFT

8 Wiring Diagram

SyncMaster 470STFT

8-1

9 Schematic Diagrams
9-1 DAC & IO Part Schematic Diagram

5

7

6

9-1

SyncMaster 470STFT

9 Schematic Diagrams
5 IC201 #94 6 IC106 #9 7 IC105, #1

CH1 RMS = 3.5 V

CH1 RMS = 3.1 V

CH1 RMS = 4.56 V

SyncMaster 470STFT

9-2

9 Schematic Diagrams

9-2 ZOOM & FRC Part Schematic Diagram

8

3

2

1 4 13 11 14

12

9 10

9-3

SyncMaster 470STFT

9 Schematic Diagrams
1 IC303 #39 2 IC304 #25 3 IC304 #26 4 CN301 #1~16

CH1 RMS = 3.6 V

CH1 RMS = 2.8 V

CH1 RMS = 2.12 V

CH1 RMS = 1.18 V

8 IC301 #141

9 IC303 #20

10 IC303 #22

11 IC303 #34

CH1 RMS = 2.3 V

CH1 RMS = 1.24 V

CH1 RMS = 400 mV

CH1 RMS = 4.4 V

12 IC302 #12

13 IC302 #5

14 IC302 #10

CH1 RMS = 2.2 V

CH1 RMS = 1.7 V

CH1 RMS = 4.3 V

SyncMaster 470STFT

9-4

9 Schematic Diagrams

9-3 Micom Part Schematic Diagram

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

0~5 0, 5 5 5 4.62 0 5 5 GND 5 5 NC 5 5 Pulse Pulse 5 NC NC Pulse Pulse

22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Pulse GND Pulse 5 5 0 0 5 5 0 Clock Clock 5 NC 3.8 5 0 5 5 GND NC

Table 9-8. IC403
pin # MODES 1024 x 768 / 75 Hz NC NC NC GND 4.43 4.46 4.87 5.03

1 2 3 4 5 6 7 8

Unit: Vrms

Table 9-9. IC404
pin # MODES 1024 x 768 / 75 Hz GND GND GND GND 5.03 5.03 GND 5.03

1 2 3 4 5 6 7 8

Unit: Vrms

9-5

SyncMaster 470STFT

Samsung Electronics Co., Ltd. September 1999. Printed in Korea Code No.: BN68-00056G