Text preview for : KD-G814.pdf part of JVC KD-G814 Service manual for CD RECEIVER (mp3)
Back to : KD-G814.part1.rar | Home
SERVICE MANUAL
CD RECEIVER
3 2005 MA185
KD-G814
Area suffix UI -------------------------- India
TABLE OF CONTENTS
1 2 3 4 5 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-29
COPYRIGHT © 2005 Victor Company of Japan, Limited
No.MA185 2005/3
SPECIFICATION
AUDIO AMPLIFIER SECTION Maximum Power Output Front Rear Continuous Power Output (RMS) Front Rear Load Impedance Equalizer Control Range Low Mid High Frequency Response Signal-to-Noise Ratio Line-Out Level/Impedance Output Impedance Subwoofer-Out Level/Impedance Other Terminals Frequency Range FM Tuner FM AM Usable Sensitivity 50 dB Quieting Sensitivity Frequency Response Stereo Separation Capture Ratio AM Tuner Sensitivity Selectivity Type Signal Detection System Number of Channels Frequency Response Dynamic Range Signal-to-Noise Ratio Wow and Flutter MP3 Decoding Format WMA (Windows Media Audio) Decoding Format GENERAL Power Requirement Grounding System Allowable Operating Temperature Dimensions (W × H × D) Mass (approx.) Design and specifications are subject to change without notice. Installation Size (approx.) Panel Size (approx.) Operating Voltage DC 14.4 V (11 V to 16 V allowance) Negative ground 0°C to +40°C 182 mm × 52 mm × 159 mm 188 mm × 58 mm × 12 mm 1.5 kg (excluding accessories) 50 W per channel 50 W per channel 19 W per channel into 4 , 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. 19 W per channel into 4 , 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. 4 (4 to 8 allowance) ±12 dB (60 Hz, 80 Hz, 100 Hz, 120 Hz) ±12 dB ±12 dB (8 kHz, 10 kHz, 12 kHz, 15 kHz) 40 Hz to 20 000 Hz 70 dB 5.0 V/20 k load (full scale) 1 k 2.0 V/20 k load (full scale) CD changer, SUBWOOFER TUNER SECTION 87.5 MHz to 108.0 MHz 531 kHz to 1 602 kHz 11.3 dBf (1.0 µV/75 ) 16.3 dBf (1.8 µV/75 ) 40 Hz to 15 000 Hz 35 dB 1.5 dB 20 µV 35 dB CD PLAYER SECTION Compact disc player Non-contact optical pickup (semiconductor laser) 2 channels (stereo) 5 Hz to 20 000 Hz 96 dB 98 dB Less than measurable limit MPEG1/2 Audio Layer 3 Max. Bit Rate: 320 kbps Max. Bit Rate: 192 kbps
Alternate Channel Selectivity (400 kHz) 65 dB
1-2 (No.MA185)
SECTION 1 PRECAUTIONS
1.1 Safety Precautions
!
Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.
!
Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
(No.MA185)1-3
1.2
Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players. Be careful to use proper grounding in the area where repairs are being performed. (1) Ground the workbench Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the traverse unit (optical pickup) on it. (2) Ground yourself Use an anti-static wrist strap to release any static electricity built up in your body.
(caption) Anti-static wrist strap
1M
(3) Handling the optical pickup · In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition. (Refer to the text.) · Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily destroy the laser diode. 1.3 Handling the traverse unit (optical pickup) (1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit. (2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a time when attaching it to the connector. (3) Handle the flexible cable carefully as it may break when subjected to strong force. (4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it. 1.4 Attention when traverse unit is decomposed *Please refer to "Disassembly method" in the text for the CD pickup unit. · Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit. (If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.) · In the assembly, be sure to remove solder from the short land after connecting the flexible wire.
Conductive material (conductive sheet) or iron plate
Short-circuit point (Soldering) Flexible wire
Pickup
1-4 (No.MA185)
1.5
Important for laser products
1.CLASS 1 LASER PRODUCT 2.DANGER : Invisible laser radiation when open and inter lock failed or defeated. Avoid direct exposure to beam. 3.CAUTION : There are no serviceable parts inside the Laser Unit. Do not disassemble the Laser Unit. Replace the complete Laser Unit if it malfunctions. 4.CAUTION : The CD,MD and DVD player uses invisible laser radiation and is equipped with safety switches which prevent emission of radiation when the drawer is open and the safety interlocks have failed or are defeated. It is dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able to function. 6.CAUTION : Use of controls, adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure.
!
Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
REPRODUCTION AND POSITION OF LABELS WARNING LABEL
CLASS 1 LASER PRODUCT
CAUTION : Visible and Invisible laser radiation when open and interlock failed or defeated. AVOID DIRECT EXPOSURE TO BEAM. (e)
ADVARSEL : Synlig og usynlig laserstråling når maskinen er åben eller interlocken fejeler. Undgå direkte eksponering til stråling. (d)
VARNING : Synlig och osynling laserstrålning när den öppnas och spärren är urkopplad. Betrakta ej strålen. (s)
VARO : Avattaessa ja suojalukitus ohitettuna tai viallisena olet alttiina näkyvälle ja näkymättömälle lasersäteilylle. Vältä säteen kohdistumista suoraan itseesi. (f)
(No.MA185)1-5
SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
1-6 (No.MA185)
SECTION 3 DISASSEMBLY
3.1 Main body section 3.1.1 Removing the front panel assembly (See Fig.1) (1) Push the detach button in the lower right part of the front panel assembly. (2) Take out the front panel assembly.
Front panel assembly
Detach button
Fig.1 3.1.2 Removing the heat sink (See Fig.2) (1) From the left side of the main body, remove the two screws A and three screws B attaching the heat sink. (2) Take out the heat sink.
A
B
A
Heat sink
Fig.2
(No.MA185)1-7
3.1.3 Removing the top chassis assembly (See Figs.3 to 6) · Prior to performing the following procedures, remove the heat sink. Reference: Remove the front panel assembly as required. (Refer to "3.1.1 Removing the front panel assembly") (1) From the bottom side of the main body, remove the two screws C attaching the top chassis assembly to the bottom chassis assembly. (See Fig.3) (2) From the both and rear sides of the main body, remove the four screws D attaching the top chassis assembly to the bottom chassis assembly. (See Figs.4 to 6) (3) Lift the top chassis assembly in the direction of the arrow, and disconnect the connector CN501 on the mechanism control board from the connector CN101 on the main board. (See Figs.5 and 6) (4) Take out the top chassis assembly from the bottom chassis assembly.
Bottom chassis assembly
C C
Top chassis assembly
Fig.3
Top chassis assembly
Bottom chassis assembly
Fig.4
D
Top chassis assembly
Mechanism control board CN501
D
Main board CN101 Bottom chassis assembly
Fig.5
D
Top chassis assembly
D
Bottom chassis assembly
Fig.6
Rear bracket
1-8 (No.MA185)
3.1.4 Removing the front chassis (See Figs.7 and 8) · Prior to performing the following procedure, remove the front panel assembly, heat sink and top chassis assembly. (1) From the both sides of the top chassis assembly, remove the two screws E attaching the front chassis. (See Figs.7 and 8) (2) Take out the front chassis
Top chassis assembly
E
Front chassis
Fig.7
Top chassis assembly
E
Front chassis
Fig.8 3.1.5 Removing the mechanism control board (See Fig.9) · Prior to performing the following procedures, remove the front panel assembly, heat sink and top chassis assembly. Reference: Remove the front chassis as required. (Refer to "3.1.4 Removing the front chassis") (1) Disconnect the card wire from the connector CN601 on the mechanism control board. (2) Remove the five screws F attaching the mechanism control board. (3) Release the claw a, and take out the mechanism control board. Reference: After attaching the mechanism control board, attach it to the claw a and pass the slot b of it into the boss of the CD mechanism assembly.
Mechanism control board
CN601
F
F
Slot b
Craw a
F
Fig.9
(No.MA185)1-9
3.1.6 Removing the CD mechanism assembly (See Fig.10) · Prior to performing the following procedures, remove the front panel assembly, heat sink and top chassis assembly. Reference: Remove the front chassis and mechanism control board as required.(Refer to "3.1.4 Removing the front chassis" and "3.1.5 Removing the mechanism control board") (1) From the inside of the top chassis assembly, remove the three screws G attaching the CD mechanism assembly. (2) Take out the CD mechanism assembly from the top chassis.
Top chassis
G
G
3.1.7 Removing the main board (See Figs.11 and 12) · Prior to performing the following procedures, remove the front panel assembly, heat sink and top chassis assembly. (1) From the rear side of the bottom chassis assembly, remove the two screws H attaching the rear bracket to the bottom chassis assembly. (See Fig.11) (2) From the top side of the bottom chassis assembly, remove the two screws J attaching the main board to the bottom chassis assembly. (See Fig.12) (3) Release the stopper of the connector CN702 on the main board in an upward direction, disconnect the card wire from the connector CN702. (See Fig.12) (4) Disconnect the wire from the connector of the front door mechanism assembly. (See Fig.12) (5) Disconnect the wire from the connector CN951 on the main board. (See Fig.12) Reference: After connecting the wires, fix the wires with the wire clamp. (6) Take out the main board from the bottom chassis assembly.
CD mechanism assembly
Fig.10
G
Rear bracket
H
Bottom chassis assembly
Fig.11
Front door mechanism assembly Connector Wire clamp Bottom chassis assembly Card wire CN702 Stopper
J
J
Main board
CN951
Fig.12
Wires
1-10 (No.MA185)
3.1.8 Removing the rear bracket (See Fig.13) · Prior to performing the following procedures, remove the front panel assembly, heat sink, top chassis assembly and main board. (1) From the rear side of the main board, remove the wires from the rear bracket in the direction of the arrow. (2) Remove the screw K, three screws L and screw M attaching the rear bracket to the main board. Reference: After attaching the rear bracket to the main board, pass the wires through the wire holder and insert them into the slots of the rear bracket.
Main board Wire Rear bracket
Wire holder
Slots Rear bracket
M
L
3.1.9 Removing the front door mechanism assembly (See Fig.14) · Prior to performing the following procedures, remove the front panel assembly, heat sink, top chassis assembly and main board. (1) From the top side of the bottom chassis assembly, remove the screw N attaching the FPC guide to the bottom chassis. (2) Remove the five screws P attaching the front door mechanism assembly to the bottom chassis. Reference: When attaching the screws N and P, apply a locking agent them. (3) Take out the front door mechanism assembly from the bottom chassis.
K
Fig.13
L
Front door mechanism assembly Bottom chassis
P
P
FPC guide
Fig.14
N
(No.MA185)1-11
3.1.10 Removing the switch board (See Figs.15 to 17) · Prior to performing the following procedures, remove the front panel assembly. (1) From the rear side of the front panel assembly, remove the four screws Q attaching the rear cover assembly to the front panel assembly. (See Fig.15) (2) Release the twelve joints c of the front panel assembly and remove the rear cover assembly. (See Fig.16) (3) Take out the switch board from the front panel assembly. (See Fig.17) Note: When removing the rear cover assembly and front board, be careful not to lose the comp. spring. (See Fig.17)
Q
Rear cover assembly
Q
Q
Fig.15
Rear cover assembly Joints c Joints c
Joints c
Fig.16
Joints c
Front panel assembly Switch board
Comp. spring
Fig.17
1-12 (No.MA185)
3.2
CD Mechanism section
3.2.1 Removing the top cover (See Figs.1 and 2) (1) Remove the four screws A on the both side of the body. (2) Lift the front side of the top cover and move the top cover backward to release the two joints a.
A
Top cover Joints a
A
A
Fig.1
Joints a
Top cover
Fig.2
(No.MA185)1-13
3.2.2 Removing the connector board (See Figs.3 to 5) CAUTION: Before disconnecting the flexible wire from the pickup, solder the short-circuit point on the pickup. No observance of this instruction may cause damage of the pickup. (1) Remove the screw B fixing the connector board. (2) Solder the short-circuit point on the pickup. (3) Disconnect the flexible wire from the pickup. (4) Move the connector board in the direction of the arrow to release the two joints b. (5) Unsolder the wires on the connector board if necessary. CAUTION: Unsolder the short-circuit point after reassembling.
Wires
B
Connector board
Joints b
Short-circuit point Fig.3
Pickup
Short-circuit point (Soldering) Flexible wire
Pickup Fig.4
Connector board
B
Flexible wire
Frame
Fig.5
1-14 (No.MA185)
3.2.3 Removing the DET switch (See Figs.6 and 7) (1) Extend the two tabs c of the feed sw. holder and pull out the switch. (2) Unsolder the DET switch wire if necessary.
DET switch
Connector board
Pickup
Fig.6
DET switch
Tab c
DET switch wire
Tab c
Fig.7
Feed sw. holder
(No.MA185)1-15
3.2.4 Removing the chassis unit (See Figs.8 and 9) · Prior to performing the following procedure, remove the top cover and connector board. (1) Remove the two suspension springs (L) and (R) attaching the chassis unit to the frame. CAUTION: · The shape of the suspension spring (L) and (R) are different. Handle them with care. · When reassembling, make sure that the three shafts on the underside of the chassis unit are inserted to the dampers certainly.
Chassis unit Suspension spring (R) Suspension spring (L) Frame
Suspension spring (R)
Fig.8
Suspension spring (L)
Chassis unit
Shaft
Shafts
Damper
Damper
Damper
Fig.9
Frame
1-16 (No.MA185)
3.2.5 Removing the clamper assembly (See Figs.10 and 11) · Prior to performing the following procedure, remove the top cover. (1) Remove the clamper arm spring. (2) Move the clamper assembly in the direction of the arrow to release the two joints d.
Clamper arm spring
Joint d
Clamper assembly Fig.10 Clamper arm spring
Chassis rivet assembly Joint d
Clamper assembly Joint d Joint d
Chassis rivet assembly Fig.11
(No.MA185)1-17
3.2.6 Removing the loading / feed motor assembly (See Figs.12 and 13) · Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw C and move the loading / feed motor assembly in the direction of the arrow to remove it from the chassis rivet assembly. (2) Disconnect the wire from the loading / feed motor assembly if necessary. CAUTION: When reassembling, connect the wire from the loading / feed motor assembly to the flame as shown in Fig.12.
Loading / feed motor assembly Fig.12
Loading / feed motor assembly
C
Fig.13
1-18 (No.MA185)
3.2.7 Removing the pickup unit (See Figs.14 to 18) · Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw D and pull out the pu. shaft holder from the pu. shaft. (2) Remove the screw E attaching the feed sw. holder. (3) Move the part e of the pickup unit upward with the pu. shaft and the feed sw. holder, then release the joint f of the feed sw. holder in the direction of the arrow. The joint g of the pickup unit and the feed rack is released, and the feed sw. holder comes off. (4) Remove the pu. shaft from the pickup unit. (5) Remove the screw F attaching the feed rack to the pickup unit. 3.2.8 Reattaching the pickup unit (See Figs.14 to 17) (1) Reattach the feed rack to the pickup unit using the screw F. (2) Reattach the feed sw. holder to the feed rack while setting the joint g to the slot of the feed rack and setting the joint f of the feed rack to the switch of the feed sw. holder correctly. (3) As the feed sw. holder is temporarily attached to the pickup unit, set to the gear of the joint g and to the bending part of the chassis (joint h) at a time. CAUTION: Make sure that the part i on the underside of the feed rack is certainly inserted to the slot j of the change lock lever. (4) Reattach the feed sw. holder using the screw E. (5) Reattach the pu. shaft to the pickup unit. Reattach the pu. shaft holder to the pu. shaft using the screw D.
Pickup unit
Part e
Feed rack
Fig.15
Feed sw. holder Pu. shaft
Part i Pickup unit
E
Slot j Joint g Joint f Joint h
D
Pu. shaft holder
Feed sw. holder
Fig.16
F
Pickup unit
Feed rack
Feed sw. holder
Joint f
E
Pu. shaft Joint g
Fig.17
Pickup unit Joint g
D
Pu. shaft holder Pickup unit Fig.14 Part e
Joint f Feed rack Feed sw. holder Fig.18
(No.MA185)1-19
3.2.9 Removing the trigger arm (See Figs.19 and 20) · Prior to performing the following procedure, remove the top cover, connector board and clamper unit. (1) Turn the trigger arm in the direction of the arrow to release the joint k and pull out upward. CAUTION: When reassembling, insert the part m and n of the trigger arm into the part p and q at the slot of the chassis rivet assembly respectively and join the joint k at a time.
Joint k
Trigger arm
Chassis rivet assembly Fig.19
Part p Trigger arm Part m Part n Chassis rivet assembly Part q
Fig.20 3.2.10 Removing the top plate assembly (See Fig.21) · Prior to performing the following procedure, remove the top cover, connector board, chassis unit, and clamper assembly. (1) Remove the screw H. (2) Move the top plate assembly in the direction of the arrow to release the two joints r. (3) Unsolder the wire marked s if necessary.
Top plate assembly
H
Joints r
s
Fig.21
1-20 (No.MA185)
3.2.11 Removing the mode sw. / select lock arm (See Figs.22 and 23) · Prior to performing the following procedure, remove the top plate assembly. (1) Bring up the mode sw. to release from the link plate (joint t) and turn in the direction of the arrow to release the joint u. (2) Unsolder the wire of the mode sw. marked s if necessary. (3) Turn the select lock arm in the direction of the arrow to release the two joints v. (4) The select lock arm spring comes off the select lock arm at the same time.
Link plate
Joint t Mode sw. Select lock arm
Joint u
s Fig.22 Select lock arm Top plate
Hook w Select lock arm Top plate Select lock arm spring
Joints v Link plate
Fig.23
(No.MA185)1-21
3.2.12 Reassembling the mode sw. / select lock arm (See Figs.24 to 26) REFERENCE: Reverse the above removing procedure. (1) Reattach the select lock arm spring to the top plate and set the shorter end of the select lock arm spring to the hook w on the top plate. (2) Set the other longer end of the select lock arm spring to the boss x on the underside of the select lock arm, and join the select lock arm to the slots (joint v). Turn the select lock arm as shown in the figure. (3) Reattach the mode sw. while setting the part t to the first peak of the link plate gear, and join the joint u. CAUTION: When reattaching the mode sw., check if the points y and z are correctly fitted and if each part operates properly.
Select lock arm spring Hook w Joint v Joint v
Select lock arm Boss x
Fig.24
Joint t Point y Link plate Point z
Fig.25
Mode sw.
Select lock arm
Joint t Link plate Joint u Fig.26
1-22 (No.MA185)
3.2.13 Removing the select arm R / link plate (See Figs.27 and 28) · Prior to performing the following procedure, remove the top plate assembly. (1) Bring up the select arm R to release from the link plate (joint a') and turn as shown in the figure to release the two joints b' and joint c'. (2) Move the link plate in the direction of the arrow to release the joint d'. Remove the link plate spring at the same time. REFERENCE: Before removing the link plate, remove the mode sw..
Select arm R
Link plate Joint c' Joint b'
Joint r
Joint b'
Joint a' Fig.27 Link plate spring Top plate Joint d'
Link plate Fig.28
3.2.14 Reattaching the Select arm R / link plate (See Figs.29 and 30) REFERENCE: Reverse the above removing procedure. (1) Reattach the link plate spring. (2) Reattach the link plate to the link plate spring while joining them at joint d'. (3) Reattach the joint a' of the select arm R to the first peak of the link plate while joining the two joints b' with the slots. Then turn the select arm R as shown in the figure. The top plate is joined to the joint c'. CAUTION: When reattaching the select arm R, check if the points e' and f' are correctly fitted and if each part operates properly.
Link plate spring Select arm R Joint c' Joint d'
Joint b' Joint b' Joint a' Fig.29
Joint a'
Link plate Point e' Point f'
Fig.30
(No.MA185)1-23
3.2.15 Removing the loading roller assembly (See Figs.31 to 33) · Prior to performing the following procedure, remove the clamper assembly and top plate assembly. (1) Push inward the loading roller assembly on the gear side and detach it upward from the slot of the joint g' of the lock arm rivet assembly. (2) Detach the loading roller assembly from the slot of the joint h' of the lock arm rivet assembly. The roller guide comes off the gear section of the loading roller assembly. Remove the roller guide and the HL washer from the shaft of the loading roller assembly. (3) Remove the screw J attaching the lock arm rivet assembly. (4) Push the shaft at the joint i' of the lock arm rivet assembly inward to release the lock arm rivet assembly from the slot of the L side plate. (5) Extend the lock arm rivet assembly outward and release the joint j' from the boss of the chassis rivet assembly. The roller guide springs on both sides come off at the same time. CAUTION: When reassembling, reattach the left and right roller guide springs to the lock arm rivet assembly before reattaching the lock arm rivet assembly to the chassis rivet assembly. Make sure to fit the part k' of the roller guide spring inside of the roller guide. (Refer to Fig.34.)
Loading roller assembly Roller guide spring
Part k'
Loading roller assembly
Roller guide spring
Fig.32
Chassis rivet assembly
Boss
Roller guide HL washer Loading roller assembly
J
Roller guide
L side plate Roller guide spring
Joint h'
Lock arm rivet assembly Joint j' Roller guide spring Joint g'
Fig.33
Joint i'
Roller guide spring
Roller guide HL washer Roller shaft assembly
Loading roller assembly Roller guide spring Lock arm rivet assembly Fig.31
Loading roller Lock arm rivet assembly Roller guide spring Fig.34
1-24 (No.MA185)
3.2.16 Removing the loading gear 5, 6 and 7 (See Figs.35 and 36) · Prior to performing the following procedure, remove the top cover, chassis unit, pickup unit and top plate assembly. (1) Remove the screw K attaching the loading gear bracket. The loading gear 6 and 7 come off the loading gear bracket. (2) Pull out the loading gear 5.
K
Loading gear bracket Loading gear 6
Loading gear 5
Loading gear 3
Fig.35
K
Loading gear bracket Loading gear 6 Loading gear 5 Loading gear 7
Fig.36
(No.MA185)1-25
3.2.17 Removing the gears (See Figs.37 to 40) · Prior to performing the following procedure, remove the top cover, chassis unit, top plate assembly and pickup unit. · Pull out the loading gear 3. (See Fig.35.) (1) Pull out the feed gear. (2) Move the loading plate assembly in the direction of the arrow to release the L side plate from the two slots m' of the chassis rivet assembly. (See Fig.37.) (3) Detach the loading plate assembly upward from the chassis rivet assembly while releasing the joint n'. Remove the slide hook and loading plate spring from the loading plate assembly. (4) Pull out the loading gear 2 and remove the change lock lever. (5) Remove the E ring and washer attaching the change gear 2. (6) The change gear 2, change gear spring and adjusting washer come off. (7) Remove the loading gear 1. (8) Move the change plate rivet assembly in the direction of the arrow to release from the three shafts of the chassis rivet assembly upward. (See Fig.38.) (9) Detach the loading gear plate rivet assembly from the shaft of the chassis rivet assembly upward while releasing the joint p'. (See Figs.38 and 40.) (10) Pull out the loading gear 4.
Joint p' Change plate rivet assembly Shafts Loading gear 4 Loading gear plate rivet assembly Shaft Loading gear 2 Loading gear 1 Chassis rivet assembly Change gear 2 Fig.38 Joint n' Slide hook Loading plate spring
E ring
Loading plate assembly
L side plate Slot m' L side plate Loading plate assembly Joint n' Feed gear Slot m' E ring Chassis rivet assembly
Fig.37
Slot m'
Slot m' Chassis rivet assembly
Fig.39
Washer Change gear 2 Change gear spring Adjusting washer Change plate rivet assembly
Loading gear 1 Loading gear 2 Change lock lever Loading gear 4
Chassis rivet assembly Loading gear plate rivet assembly
Fig.40
1-26 (No.MA185)
3.2.18 Removing the turn table / spindle motor (See Figs.41 and 42) · Prior to performing the following procedure, remove the top cover, connector board, chassis unit and clamper assembly. (1) Remove the two screws L attaching the spindle motor assembly through the slot of the turn table on top of the body. (2) Unsolder the wire on the connector board if necessary.
Turn table
L
Fig.41
L
Turn table
Spindle motor Fig.42
(No.MA185)1-27
SECTION 4 ADJUSTMENT
4.1 Adjustment method Standard measuring conditions Power supply voltage Load impedance Output Level DC14.4V(10.5 to 16V) 20K(2 Speakers connection) Line out 5.0V (Vol. MAX) Test instruments required for adjustment (1) Digital oscilloscope (100MHz) (2) Electric voltmeter (3) Digital tester (4) Tracking offset meter (5) Test Disc JVC :CTS-1000 (6) Extension cable for check EXTSH002-22P × 1 Standard volume position Balance and Bass &Treble volume : lndication"0" Loudness : OFF How to connect the extension cable for adjusting Caution: Be sure to attach the heat sink and rear bracket onto the power amplifier IC and regulator IC respectively, before supply the power. If voltage is applied without attaching these parts, the power amplifier IC and regulator IC will be destroyed by heat.
Dummy load Exclusive dummy load should be used for AM,and FM. For FM dummy load,there is a loss of 6dB between SSG output and antenna input.The loss of 6dB need not be considered since direct reading of figures are applied in this working standard.
Extension cable: EXTSH002-22P
Heat sink
Rear bracket
1-28 (No.MA185)
SECTION 5 TROUBLESHOOTING
5.1 Feed section
Is 5v or 0V at IC621 pin 40?
NO
Is the wiring for IC621 pin 40 correct?
YES
Is 5V present at IC681 pin 6? YES Check the vicinity of IC621. Check the feed motor connection wiring.
NO
Check CD8V.
YES Is 4V present at both sides of the feed motor? YES Check the feed motor.
5.2 Focus section
NO NO Is 6V or 2V present at YES IC681 pins 17 and 18? NO Check IC681.
When the lens is moving:
4V
NO
Check the circuits in the vicinity of IC681 pins 1 and 2.
Does the S-search waveform appear at IC681 pins 13 and 14?
YES Check the pickup and its connections.
YES
5.3 Spindle section
Is the disk rotated? YES Does the RF signal appear at IC601 pin 19? YES Is the RF waveform at IC601 pin 19 distorted? YES Proceed to the Tracking section
5.4 Tracking section
NO
Is 4V present between IC681 pins 15 and 16? YES Check the spindle motor and its wiring.
NO
Is 4V present at IC621 pin 41? YES Check the vicinity of IC681.
NO Check IC621.
NO NO
Check the circuits in the vicinity of IC601 or the pickup.
When the disc is rotated at first:
Approx. 1.2V
NO
Check the circuits in the vicinity of IC601 pins 2 to 12.
NO
Check the pickup and its connections.
Is the tracking error signal output at IC601 pins 11 and 12? YES Check IC621.
(No.MA185)1-29
5.5
Signal processing section
Is the sound output from NO both channels (L, R)? YES Normal
No sound from either channel. YES Is 9V present at IC161 pin 40?
NO
Compare the L-ch and R-ch to locate the defective point.
NO
Is 9V present at IC901 pin 13? YES Check the connection between IC901 pin13 and IC161 pin 40.
NO
Check IC901 and its peripheral circuits.
YES
Is the audio signal (including sampling output components) output to IC572 pins 1 and 7 during playback? YES Is the audio signal output at IC161 pins 36 to 39 during playback? YES
NO
Check IC572 and its peripheral circuits.
NO
Check IC161 and its peripheral circuits.
Is the audio signal output NO at IC361/IC381 pins 12 and 13 during playback? YES Check the power amp. IC301.
Check IC361/IC381 and its peripheral circuits.
1-30 (No.MA185)
5.6
Maintenance of laser pickup
5.7
Replacement of laser pickup
(1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens with a alcohol soaked cotton swab. (2) Life of the laser diode When the life of the laser diode has expired, the following symptoms will appear. · The level of RF output (EFM output: amplitude of eye pattern) will be low.
Turn of the power switch and, disconnect the power cord.
Replace the pickup with a normal one. (Refer to "Removing the pickup unit" on the previous page.)
Is RF output 1.3 0.4Vp-p?
NO Replace it. Plug the power cord in, and turn the power on. At this time, check that the laser emits for about seconds and the objective lens moves up and down. Note: Do not observe the laser beam directly.
YES OK
(3) Semi-fixed resistor on the APC PC board The semi-fixed resistor on the APC printed circuit board which is attached to the pickup is used to adjust the laser power.Since this adjustment should be performed to match the characteristics of the whole optical block, do not touch the semi-fixed resistor. If the laser power is lower than the specified value, the laser diode is almost worn out, and the laser pickup should be replaced. If the semi-fixed resistor is adjusted while the pickup is functioning normally, the laser pickup may be damaged due to excessive current.
Play a disc.
Check the eye-pattern at RF test point.
Finish.
(No.MA185)1-31
5.8
16 PIN CORD DIAGRAM
BK RD BL BL/WH YL
8 7 6 5
16
OR/WH 15 NC BR 14 13
BK RD BL
Black Red Blue
GN VI GY
YL
Green Violet Gray
4 3 2 1
WH GN VI GY
WH White
WH/BK 12 GN/BK VI/BK GY/BK 11 10 9
Yellow
Orange
BR
Brown
OR
16 YL 8 BK 7 RD 15 OR/WH 13 BR 3 GN 11 GN/BK 2 VI 10 VI/BK 4 WH 12 WH/BK 1 GY 9 GY/BK 5 BL/WH
MEMORY GND ACC ILL TEL RL+ RLRR+ RRFL+ FLFR+ FRREMOTE
ION! CAUT REMOTE OUTPUT ONLY
GND
6 BL
ANT
RR FR FL RL REMOTE TEL
1-32 (No.MA185)
Rear Front Front Rear
Right Right Left Left
ANT ACC ILL GND MEMORY
POWER ANTENNA
Auto ACC
Antenna Line Control
Illuminations Ground Memory
Remote out Telephone muting
Backup
Battery+
(No.MA185)1-33
Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY CAR ELECTRONICS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(No.MA185)
Printed in Japan VPT
CD RECEIVER
KD-G814
For canceling the display demonstration, see page 8.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0306-001A
[UI]
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. 3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Warning:
If you need to operate the receiver while driving, be sure to look ahead carefully or you may be involved in a traffic accident.
How to reset your unit
Caution on volume setting:
Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.
This will reset the microcomputer. Your preset adjustments will also be erased.
How to forcibly eject a disc
If a disc cannot be recognized by the receiver or cannot be ejected, eject the disc as follows.
If this does not work, reset your receiver.
2
Contents
How to reset your unit ........................... How to forcibly eject a disc ................... How to read this manual ........................ How to use the MODE button ............... 2 2 4 4
Sound adjustments ................ 17 Selecting preset sound modes (iEQ: intelligent equalizer) ................ 17
Adjusting the sound ............................... 18 Storing your own sound adjustments..... 19
Control panel --
KD-G814 ......... RM-RK50
5
5 6
Parts identification .................................
General settings -- PSM ......... 20
Basic procedure ..................................... 20
Remote controller --
... 6
Main elements and features ...................
Other main functions ............. 22
Assigning titles to the sources ............... 22 Changing the control panel angle .......... 23 Detaching the control panel ................... 23
Getting started ....................... 7 Basic operations .................................. 7
Canceling the display demonstrations ... Setting the clock .................................... 8 8
Radio operations ................... 9 Listening to the radio........................... 9
Storing stations in memory .................... 10 Listening to a preset station ................... 10
External component operations... 24 Playing an external component ............ 24 Maintenance .......................... 25 More about this receiver ........ 26 Troubleshooting ..................... 28 Specifications ......................... 31
Disc operations ...................... 11 Playing a disc in the receiver ............... 11 Playing discs in the CD changer ........... 12
Other main functions ............................. 14 Changing the display information ......... 15 Selecting the playback modes................ 16
*For safety....
· Do not raise the volume level too much, as this will block outside sounds, making driving dangerous. · Stop the car before performing any complicated operations.
*Temperature inside the car....
If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit. 3
How to read this manual
The following methods are used to made the explanations simple and easy-to-understand: · Some related tips and notes are explained in "More about this receiver" (see pages 26 and 27). · Button operations are mainly explained with the illustrations as follows:
How to use the MODE button
If you press MODE, the receiver goes into functions mode, then the number buttons and 5/ buttons work as different function buttons. Ex.: When number button 2 works as MO (monaural) button.
Press briefly.
Press repeatedly.
Press either one.
Time countdown indicator
Press and hold until your desired response begins. Press and hold both buttons at the same time.
To use these buttons for original functions again after pressing MODE, wait for 5 seconds without pressing any of these buttons until the functions mode is cleared. · Pressing MODE again also clears the functions mode.
The following marks are used to indicate... : Built-in CD player operations. : External CD changer operations.
4
Control panel --
KD-G814
Parts identification
Display window
1 2 3 4 5 6 7 8 9 p
q w e r t y u i o ; a s
(standby/on attenuator) button DISP (display) button SEL (select) button Control dial Display window (angle) button 0 (eject) button 5 (up) button / +10 button (down) button / 10 button MODE button Remote sensor · DO NOT expose the remote sensor to strong light (direct sunlight or artificial lighting). SOURCE button BAND button Reset button EQ (equalizer) button MO (monaural) button SSM (Strong-station Sequential Memory) button INT (intro) button RPT (repeat) button RND (random) button Number buttons 4 / ¢ buttons (control panel release) button
Display window
d Disc information indicators--TAG (ID3 Tag), (track/file), (folder) f MP3 indicator g CH (CD changer) indicator · Lights up only when CD-CH is selected for the playback source. h CD indicator j WMA indicator k Main display l Equalizer pattern indicator Audio level indicator / EQ (equalizer) indicator z Band indicators--FM1, FM2, FM3, AM x Tuner reception indicators--ST (stereo), MO (monaural) c Playback mode / item indicators-- (folder), (disc), RND (random), INT (intro), RPT (repeat) v TRACK indicator b Source / clock display n LOUD (loudness) indicator m Audio / volume level indicator
5
Remote controller --
Installing the lithium coin battery (CR2025)
RM-RK50
Main elements and features
· When operating, aim the remote controller directly at the remote sensor on the receiver. Make sure there is no obstacle in between.
1
Warning:
· Store the battery in a place where children cannot reach to avoid risk of accident. · To prevent the battery from over-heating, cracking, or starting a fire: Do not recharge, short, disassemble, or heat the battery or dispose of it in a fire. Do not leave the battery with other metallic materials. Do not poke the battery with tweezers or similar tools. Wrap the battery with tape and insulate when throwing away or saving it.
2
3 4
5
Caution:
6
(standby/on/attenuator) button · Turns on and off the power and also attenuates the sound. 5 U (up) / D (down) buttons · 5 U: Changes the FM/AM bands. · D : Changes the preset stations. · Changes the folder of the MP3/WMA discs. · While playing an MP3 disc on an MP3-compatible CD changer: Changes the disc if pressed briefly. Changes the folder if pressed and held. VOL / VOL + buttons · Adjusts the volume level. SOUND button · Selects the sound mode (iEQ: intelligent equalizer). SOURCE button · Selects the source. 2 R (reverse) / F (forward) 3 buttons · Searches for stations if pressed briefly. · Fast-forwards or reverses the track if pressed and held. · Changes the tracks of the disc.
6
Getting started
Basic operations
~ Y
/
Adjust the volume.
Volume level appears.
You cannot select some sources if they are not ready.
Volume level indicator
!
For FM/AM tuner only
@
Adjust the sound as you want. (See pages 17 19.)
To drop the volume in a moment (ATT)
To restore the sound, press it again.
To turn off the power
7
Canceling the display demonstrations
If no operations are done for about 20 seconds, display demonstration starts. [Initial: DEMO ON]--see page 20.
Setting the clock
1
1
2 Set the hour and minute.
1 Select "CLOCK HOUR," then adjust the hour. 2 Select "CLOCK MINUTE," then adjust the minute.
2
3 Finish the procedure. 3
To check the current clock time when the power is turned off
4 Finish the procedure.
To activate the display demonstration
In step 3 above...
8
Radio operations
Listening to the radio
~ Y
Selected band appears.
To tune in to a station manually
In step ! on the left... 1
2 Select the desired station frequencies.
Lights up when receiving an FM stereo broadcast with sufficient signal strength.
!
When an FM stereo broadcast is hard to receive
1
Start searching for a station.
2
When a station is received, searching stops. To stop searching, press the same button again.
Lights up when monaural mode is activated.
Reception improves, but stereo effect will be lost. To restore the stereo effect, repeat the same procedure so that the MO indicator goes off. 9
Storing stations in memory
You can preset six stations for each band.
2 3
FM station automatic presetting-- SSM (Strong-station Sequential Memory) 1 4 2 Select the FM band (FM1 FM3)
you want to store into.
Preset number flashes for a while.
3 1 4
"SSM" appears, then disappears when automatic presetting is over. Local FM stations with the strongest signals are searched and stored automatically in the FM band.
Listening to a preset station
2 3 Select the preset station (1 6) you
want.
Manual presetting
Ex.: Storing FM station of 92.5 MHz into the preset number 4 of the FM1 band.
or
1
10
Disc operations
Playing a disc in the receiver
All tracks will be played repeatedly until you change the source or eject the disc.
About MP3 and WMA discs
MP3 and WMA (Windows Media® Audio) "tracks" (words "file" and "track" are used interchangeably) are recorded in "folders." · When inserting an MP3 or a WMA disc:
· When inserting an audio CD or a CD Text disc:
Total playing time Total track number of the inserted disc of the inserted disc
Total folder number
Total file number
CD Text: Disc title/performer = Track title appears automatically (see page 15).
Elapsed playing time Current track number
* Disc information appears automatically (see page 15).
To stop play and eject the disc
Elapsed playing time Current track number
The receiver draws the disc, then the control panel goes back to previous position (see page 23).
Selected folder number
* Either the MP3 or WMA indicator lights up depending on the detected file. 11
Playing discs in the CD changer
About the CD changer
It is recommended to use the JVC MP3compatible CD changer with your receiver. · You can also connect other CH-X series CD changers (except CH-X99 and CH-X100). However, they are not compatible with MP3 discs, so you cannot play back MP3 discs. · You cannot use the KD-MK series CD changers with this receiver. · Disc text information recorded in the CD Text can be displayed when a JVC CD Text compatible CD changer is connected. Before operating your CD changer: · Refer also to the Instructions supplied with your CD changer. · You cannot control and play any WMA disc in the CD changer.
~
* If you have changed "EXTERNAL IN" setting to "EXTERNAL IN" (see page 21), you cannot select the CD changer.
Selected disc number
Y
Select a disc.
For disc number from 01 06:
All tracks of the inserted discs in the magazine will be played repeatedly until you change the source or eject the magazine from the CD changer.
For disc number from 07 12:
12
· When the current disc is an MP3 disc:
To fast-forward or reverse the track
Fast-forwards.
Folder name*
Reverses.
To go to the next or previous tracks
Selected folder number To the following tracks.
Disc information appears automatically (see page 15).
Elapsed playing Current track time number
To the beginning of the current track, then the previous tracks.
To go to the next or previous folders (only for MP3 and WMA discs)
For MP3 discs: * "ROOT" appears if no folder is included in the disc. For WMA discs:
To next folders.
· When the current disc is an audio CD or a CD Text disc:
To previous folders.
CD Text: Disc title/performer = Track title appears automatically (see page 15).
Elapsed playing Current track time number
13
To locate a particular track (for CD) or folder (for MP3 or WMA discs) directly
To select a number from 01 06:
2
To select a number from 07 12:
First time you press +10 or 10 button, the track skips to the nearest higher or lower track with a track number of multiple ten (ex. 10th, 20th, 30th). Then each time you press the button, you can skip 10 tracks. · After the last track, the first track will be selected and vice versa.
3
· To use folder search on MP3/WMA discs, it is required that folders are assigned with 2-digit numbers at the beginning of their folder names--01, 02, 03, and so on. · To select a particular track in a folder (for MP3 or WMA disc) after selecting a folder:
Prohibiting disc ejection
You can lock a disc in the loading slot.
Other main functions
Skipping a track quickly during play
To cancel the prohibition, repeat the same procedure. · For MP3 or WMA disc, you can skip a track within the same folder. Ex.: To select track 32 while playing track 6
1
14
Changing the display information
While playing an audio CD or a CD Text (
/
)
*1 If no title is assigned to an audio CD, "NO NAME" appears. To assign a title to an audio CD, see page 22.
While playing an MP3 (
/
) or WMA (
) disc
· When "TAG DISPLAY" is set to "TAG DISP ON" (see page 21)
*2 If an MP3/WMA file does not have ID3 tags, folder name and file name appear. In this case, the TAG indicator will not light up. · When "TAG DISPLAY" is set to "TAG DISP OFF"
15
Selecting the playback modes
You can use only one of the following playback modes at a time.
1 2 Select your desired playback mode.
Repeat play Mode
TRK RPT
Plays repeatedly
: The current track. · RPT lights up. FLDR RPT*1 : All tracks of the current folder. · and RPT light up. DISC RPT*2 : All tracks of the current disc. · and RPT light up. RPT OFF : Cancels.
Ex.: When "TRK RPT" is selected while playing an MP3 disc in the receiver
Random play
Mode
FLDR RND*1
Plays at random
: All tracks of the current folder, then tracks of the next folder and so on. · and RND light up. : All tracks of the current disc. · and RND light up. : All tracks of the inserted discs. · RND lights up. : Cancels.
DISC RND MAG RND*2
Ex.: When "DISC RND" is selected while playing an MP3 disc in the receiver
RND OFF
Intro scan
Mode
TRK INT FLDR INT*1
Plays the beginning 15 seconds of...
: All tracks of the current disc. · INT lights up. : The first track of every folder of the current disc. · and INT light up. : The first tracks of the inserted discs. · and INT light up. : Cancels. ) disc.
DISC INT*2
Ex.: When "TRK INT" is selected while playing an MP3 disc in the receiver
INT OFF /
*1 Only while playing an MP3 ( *2
) or WMA ( ).
Only while playing discs in the CD changer (
16
Sound adjustments
Selecting preset sound modes (iEQ: intelligent equalizer)
You can select a preset sound mode suitable to the music genre.
To select the sound mode directly
~ Y !
FLAT (no sound mode is applied) " HARD ROCK " R&B " POP " JAZZ " DANCE MUSIC " COUNTRY " REGGAE " CLASSIC " USER 1 " USER 2 " USER 3 " (back to the beginning)
Indication pattern changes for each sound mode.
Ex.: When "HARD ROCK" is selected
17
Adjusting the sound
You can adjust the sound characteristics to your preference.
Indication
FAD*1 (fader)
To do:
Adjust the front and rear speaker balance.
Range
R06 (Rear only) to F06 (Front only) L06 (Left only) to R06 (Right only) LOUD ON LOUD OFF
1
BAL (balance) Adjust the left and right speaker balance.
2
LOUD (loudness)
Indication pattern changes as you adjust the fader or balance.
Boost low and high frequencies to produce a well-balanced sound at low volume level. Adjust the subwoofer output level. Adjust the volume.
WOOFER*2
00 (min.) to 08 (max.) 00 (min.) to 30 or 50 (max.)*4
Ex.: When "FAD" is selected
VOL*3 (volume)
*1 If you are using a two-speaker system, set the fader level to "00." *2 This takes effect only when a subwoofer is connected. *3 Normally the control dial works as the volume control. So you do not have to select "VOL" to adjust the volume level. *4 Depending on the amplifier gain control setting. (See page 21 for details.)
18
Storing your own sound adjustments
You can adjust the sound modes and store your own adjustments in memory.
* By pressing 4 or ¢, you can directly move as follows:
5 Adjust the selected sound elements.
1
2
Indication LOW
Preset values MID
06 (min.) to +06 (max.)
HI
06 (min.) to +06 (max.) 8kHz 10kHz 12kHz 15kHz
3
LEVEL
06 (min.) to +06 (max.) 60Hz 80Hz 100Hz 120Hz 1 (min.) to 4 (max.)
FREQ
Ex.: When "JAZZ" is selected
WIDTH
4 Select the sound elements to adjust.
1 (min.) to 2 (max.)
6 Repeat steps 4 and 5 to set (or
adjust) the other sound elements.
7 Select one of the user sound modes
LOW LEVEL* = LOW FREQ = LOW WIDTH = MID LEVEL* = MID WIDTH = HI (high) LEVEL* = HI (high) FREQ = (back to the beginning) · LEVEL (LOW, MID, HI): Adjust the enhancement level. · FREQ (LOW, HI): Select the center frequency to adjust. · WIDTH (LOW, MID): Select the band width level.
(USER 1, USER 2, USER 3).
8 Store the adjustments.
19
General settings -- PSM
Basic procedure
You can change PSM (Preferred Setting Mode) items listed in the table that follows.
3 Adjust the PSM item selected.
1 4 Repeat steps 2 and 3 to adjust the
other PSM items if necessary.
2 Select a PSM item.
5 Finish the procedure.
Ex.: When "DIMMER MODE" is selected
Indications
DEMO MODE Display demonstration
Selectable settings, [reference page]
DEMO ON DEMO OFF : [Initial]; Display demonstration will be activated automatically if no operation is done for about 20 seconds, [8]. : Cancels.
CLOCK HOUR Hour adjustment CLOCK MINUTE Minute adjustment CLOCK DISP Clock display
1 12, [8] [Initial: 1 (1:00)] 00 59, [8] [Initial: 00 (1:00)] CLK DISP ON : [Initial]; Clock display is shown on the lower part of the display. CLK DISP OFF : Current source indication (ex. station band, disc number, etc.) is shown on the lower part of the display. · Press DISP repeatedly to show the other information for about 5 seconds. LEVEL 1[Initial]/LEVEL 2: Display the audio level meter with different illumination pattern. EQ & LEVEL : Display the equalizer pattern and the audio level meter. SILENT : Display the equalizer pattern and volume level meter.
LEVELMETER Audio/volume level meter
20
Indications
DIMMER MODE Dimmer
Selectable settings, [reference page]
DIMMER AUTO DIMMER ON DIMMER OFF : [Initial]; Dims the display when you turn on the headlights. : Activates dimmer. : Cancels.
TELEPHONE Telephone muting
MUTING 1/MUTING 2 : Select either one which mutes the sounds while using the cellular phone. · If CD or CD changer is selected as the source, playback pauses during telephone muting. MUTING OFF : [Initial]; Cancels. BEEP ON BEEP OFF 01 10 : [Initial]; Activates the key-touch tone. : Deactivates the key-touch tone. : Adjust the display contrast to make the display indications clear and legible. [Initial: 08]
BEEP SWITCH Key-touch tone CONTRAST Display contrast
SCROLL MODE*1 Scroll
SCROLL ONCE : [Initial]; Scrolls the disc information once. SCROLL AUTO : Repeats scrolling (5-second intervals in between). SCROLL OFF : Cancels. · Pressing DISP for more than one second can scroll the display regardless of the setting. FREQ 55 Hz FREQ 85 Hz FREQ 115 Hz : Frequencies lower than 55 Hz are sent to the subwoofer. : [Initial]; Frequencies lower than 85 Hz are sent to the subwoofer. : Frequencies lower than 115 Hz are sent to the subwoofer. : [Initial]; To use a JVC CD changer, [12]. : To use another external component, [24]. : [Initial]; Shows the ID3 tag while playing MP3/ WMA tracks, [15]. : Cancels.
WOOFER FREQ Subwoofer cutoff frequency
EXTERNAL IN*2 External input TAG DISPLAY Tag display
CHANGER EXTERNAL IN TAG DISP ON TAG DISP OFF
AMP.GAIN Amplifier gain control
You can change the maximum volume level of this receiver. LOW POWER : VOL 00 VOL 30 (Select this if the maximum power of the speaker is less than 50 W to prevent them from damaging the speaker.) HIGH POWER : [Initial]; VOL 00 VOL 50
*1 Some characters or symbols will not be shown (and will be blanked) or substituted on the display. *2 Displayed only when one of the following sources is selected --FM, AM, or CD.
21
Other main functions
Assigning titles to the sources
You can assign titles to station frequencies and CDs (both in this receiver and in the CD changer).
3 Assign a title.
1 Select a character set.
Sources
Station frequencies
Maximum number of characters
Up to 9 characters (up to 30 station frequencies including both FM and AM)
2 Select a character.
For available characters, see page 25.
CDs/CD-CH* Up to 32 characters (up to 30 discs) * You cannot assign a title to a CD Text or an MP3/WMA disc.
1 Select the sources.
· For FM/AM tuner: Select a station. · For a CD in this receiver: Insert a CD. · For CDs in the CD changer: Select "CD-CH," then select a disc number.
3 Move to the next (or previous) character position.
2 Enter the title assignment mode.
4 Repeat steps 1 to 3 until you finish entering the title.
4 Finish the procedure.
Ex.: When you assign a title to a CD
To erase the entire title
In step 2 on the left...
22
Changing the control panel angle
Detaching the control panel
When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder.
The control panel changes its angle as follows:
Detaching the control panel
Before detaching the control panel, be sure to turn off the power.
Caution:
Do not insert your finger behind the control panel.
Attaching the control panel
23
External component operations
Playing an external component
You can connect an external component to the CD changer jack on the rear using the Line Input Adapter KS-U57 (not supplied). Before operating the external component, select the external input correctly (see page 21). · For connection, see Installation/Connection Manual (separate volume).
Y !
Turn on the connected component and start playing the source. Adjust the volume.
~ /
· If "EXTERNAL" does not appear, see page 21 and select the external input (EXTERNAL IN).
Adjust the sound as you want. (See pages 17 19.)
24
Maintenance
How to clean the connectors
Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors.
To keep discs clean
A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge. · Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.
To play new discs
New discs may have some rough spots around the inner and outer edges. If such a disc is used, this receiver may reject the disc. To remove these rough spots, rub the edges with a pencil or ball-point pen, etc.
Connector
Moisture condensation
Moisture may condense on the lens inside the CD player in the following cases: · After starting the heater in the car. · If it becomes very humid inside the car. Should this occur, the CD player may malfunction. In this case, eject the disc and leave the receiver turned on for a few hours until the moisture evaporates.
Available character
Upper case
Lower case
How to handle discs
When removing a disc from Center holder its case, press down the center holder of the case and lift the disc out, holding it by the edges. · Always hold the disc by the edges. Do not touch its recording surface. When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up). · Make sure to store discs into the cases after use. Do not use the following discs:
Warped disc Sticker Sticker residue Disc Stick-on label
Numbers and symbols
25
More about this receiver
Basic operations
Turning on the power
· By pressing SOURCE on the receiver, you can also turn on the power.
Inserting a disc
· When a disc is inserted upside down, the control panel moves down, and the disc automatically ejects from the loading slot. · If you keep the control panel open for about 1 minute, (beep sound when the "BEEP SWITCH" setting is turned "BEEP ON"--see page 21) the control panel returns to its previous position. · Do not insert 8 cm discs (single CD) and unusual shape discs (heart, flower, etc.) into the loading slot.
Turning off the power
· If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power.
Selecting the sources
· When no disc is loaded in the receiver, "CD" cannot be selected. · Without connecting to the CD changer, "CD-CH" cannot be selected.
Playing a disc
· While playing an audio CD: If a title has been assigned to the audio CD (see page 22), it will be shown on the display. · While fast-forwarding or reversing on an MP3 or WMA disc, you can only hear intermittent sounds.
Tuner operations
Storing stations in memory
· During SSM search... All previously stored stations are erased and stations are stored newly. Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency). When SSM is over, the station stored in No. 1 will be automatically tuned in. · When storing a station manually, a previously preset station is erased when a new station is stored in the same preset number.
Playing a CD-R or CD-RW
· Use only "finalized" CD-Rs or CD-RWs. · This receiver can play back only the files of the same type which is first detected if a disc includes both audio CD (CD-DA) files and MP3/WMA files. · This receiver can play back multi-session discs; however, unclosed sessions will be skipped while playing. · Some CD-Rs or CD-RWs may not play back on this receiver because of their disc characteristics, and for the following causes: Discs are dirty or scratched. Moisture condensation occurs on the lens inside the receiver. The pickup lens inside the receiver is dirty. CD-R/CD-RW on which the files are written with "Packet Write" method. There are improper recording conditions (missing data, etc.) or media conditions (stain, scratch, warp, etc.). · CD-RWs may require a longer readout time since the reflectance of CD-RWs is lower than that of regular CDs. · Do not use the following CD-Rs or CD-RWs: Discs with stickers, labels, or protective seal stuck to the surface.
Disc operations
Caution for DualDisc playback
· The Non-DVD side of a "DualDisc" does not comply with the "Compact Disc Digital Audio" standard. Therefore, the use of NonDVD side of a DualDisc on this product may not be recommended.
General
· This receiver has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/ CD-RWs (Rewritable) in audio CD (CD-DA), MP3 and WMA format. · When a disc has been loaded, selecting "CD" for the playback source starts disc play.
26
Discs on which labels can be directly printed by an ink jet printer. Using these discs under high temperatures or high humidity may cause malfunctions or damage to discs.
Playing an MP3/WMA disc
· This receiver can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case--upper/lower). · This receiver can show the names of albums, artists (performer), and ID3 Tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for MP3 files and for WMA files. · This receiver can display only one-byte characters. No other characters can be correctly displayed (see page 25). · This receiver can play back MP3/WMA files meeting the conditions below: Bit rate: 8 kbps -- 320 kbps Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) 48 kHz, 44.1 kHz, 32 kHz (for WMA) Disc format: ISO 9660 Level 1/ Level 2, Romeo, Joliet, Windows long file name · The maximum number of characters for file/ folder names vary among the disc format used (includes 4 extension characters--<.mp3> or <.wma>). ISO 9660 Level 1: up to 12 characters ISO 9660 Level 2: up to 31 characters Romeo*: up to 128 (72) characters Joliet*: up to 64 (36) characters Windows long file name*: up to 128 (72) characters * The parenthetic figure is the maximum number of characters for file/folder names in case the total number of files and folders is 313 or more. · This receiver can recognize the total of 512 files, of 200 folders, and of 8 hierarchies. · This receiver can play back the files recorded in VBR (variable bit rate). The files recorded in VBR have a discrepancy in elapsed time display, and do not show the actual elapsed time. Especially, after performing the search function, this difference becomes noticeable.
· This receiver cannot play back the following files: MP3 files encoded with MP3i and MP3 PRO format. MP3 files encoded in an unappropriated format. MP3 files encoded with Layer 1/2. WMA files encoded with lossless, professional, and voice format. WMA files which are not based upon Windows Media® Audio. WMA files copy-protected with DRM. Files which have the data such as WAVE, ATRAC3, etc. · The search function works but search speed is not constant.
Changing the source
· If you change the source, playback also stops (without ejecting the disc). Next time you select "CD" or "CD-CH" for the playback source, disc play starts from where it has been stopped previously.
Ejecting a disc
· If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to prevent it from dust. (Disc will not play this time.)
General settings--PSM
· If you have change the "TAG DISPLAY" setting from "TAG DISP OFF" to "TAG DISP ON" while playing MP3/WMA file, the tag display will be activated when the next file starts playing. · If you change the "AMP.GAIN" setting from "HIGH POWER" to "LOW POWER" while the volume level is set higher than "VOL 30," the receiver automatically changes the volume level to "VOL 30."
Other main functions
· If you try to assign a title to a 31st disc or to the 31st station frequency, "NAME FULL" appears. Delete unwanted titles before assignment. · Titles assigned to discs in the CD changer can also be shown if you playback the disc from the receiver. · The control panel moves to its previous angle each time you turn on the power. 27
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
Symptoms
· Sound cannot be heard from the speakers.
Causes
The volume level is set to the minimum level. Connections are incorrect.
Remedies
Adjust it to the optimum level. Check the cords and connections. Reset the receiver (see page 2). Reset the receiver (see page 2). Store stations manually.
General
· The receiver does not work at all. · When "PUSH RESET" appears on the display.
The built-in microcomputer may have functioned incorrectly due to noise, etc. There is something blocking the control panel movement. Signals are too weak.
FM/AM
· SSM automatic presetting does not work. · Static noise while listening to the radio. · Disc cannot be played back. · CD-R/CD-RW cannot be played back. · Tracks on the CD-R/ CD-RW cannot be skipped.
The antenna is not connected Connect the antenna firmly. firmly. Disc is inserted upside down. CD-R/CD-RW is not finalized. Insert the disc correctly. · Insert a finalized CD-R/ CD-RW. · Finalize the CD-R/CD-RW with the component which you used for recording. Unlock the disc (see page 14). Eject the disc forcibly (see page 2). Stop playback while driving on rough roads. Change the disc. Check the cords and connections. Insert the disc correctly.
Disc playback
· Disc can be neither played back nor ejected.
Disc is locked. The CD player may have functioned incorrectly.
· Disc sound is sometimes interrupted.
You are driving on rough roads. Disc is scratched. Connections are incorrect.
· "NO DISC" appears on the display.
Disc is inserted incorrectly.
28
Symptoms
· Disc cannot be played back.
Causes
No MP3/WMA tracks are recorded on the disc. MP3/WMA tracks do not have the extension code <.mp3> or <.wma> in their file names. MP3/WMA tracks are not recorded in the format compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.
Remedies
Change the disc. Add the extension code <.mp3> or <.wma> to their file names. Change the disc. (Recor