Text preview for : TECRA 9000 SERIES pt2.pdf part of Toshiba Tecra 9000 I need the service/repair manual, please?
Too big for 1 file, had to split to 3
Back to : TECRA 9000 SERIES pt2.pdf | Home
FIELD REPLACEABLE UNIT DOCUMENTATION
Tecra 9000 Series
KEYBOARD REMOVAL
TM
Latch
Keyboard
Keyboard holder 2. Turn the computer right side up and open the display panel. 3. Using the case separator, unlatch the keyboard holder at the top of the keyboard.
M2.5x2.8 silver screws 4. Remove two M2.5x2.8 silver screws securing the keyboard.
KEYBOARD REMOVAL
MODEM BOARD REMOVAL
Keyboard Modem board Keyboard cable PJ123
5. Lift out the keyboard and set it as shown above(Place an insulator between the keyboard and the LCD to prevent scratches on the LCD). 6. Disconnect the keyboard cable from PJ123 on the system board.
M2x4 brass screws 1. Remove two M2x4 brass screws securing the modem board. 2. Disconnect the modem board from PJ125 on the system board.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Tecra 9000 Series
WIRELESS LAN CARD REMOVAL
TM
Mini-PCI connector clips
Mini PCI cover
M2.5x4 security torx screw
Wireless LAN card
Black coax cable
White coax cable
1. Remove one M2x4 security torx screw securing the mini PCIcover and lift out the cover.
TOP COVER REMOVAL
M2.5x8 silver screws M2.5x4 black flat head screw
2. Disconnect the black and white coax from the wireless LAN card. 3. Spread the Mini-PCI connector clips and pull the Wireless LAN card out of the connector about 45 degree angle.
Glass tape
M2.5x14 black screw
LCD/FL cable
M2.5x2.8 silver flat PJ127 head screws M2x12 silver screws
Speaker cable
M2.5x16 silver screws 1. Turn the computer upside down and remove the following screws: -2 M2.5x2.8 silver flat head screws -1 M2.5x4 black flat head screw -4 M2.5x8 silver screws -4 M2x12 silver screws -6 M2.5x16 silver screws 2. Turn the computer right side up and open the display.
PJ122 M2.5x8 silver screws Membrane switch cable 3. Disconnect the speaker cable from PJ127 and the membrane switch cable from PJ122 on the top board 4. Remove the glass tape securing the LCD/FL cable and disconnect the cable from the bottom board. 5. Remove two M2.5x8 silver screws and one M2.5x14 black screw from the keyboard area. 5. Lift out the top cover assembly. Note: When installing the top cover, ensure that the bluetooth coaxial cable is properly routed to the Bluetooth slot.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Tecra 9000 Series
COOLING MODULE REMOVAL
Cooling module Fan cable CPU
TM
CPU REMOVAL
M2.5x10 black flat head screws Open Glass tape PJ770 Close
1. Remove the glass tape securing the fan cable and disconnect the cable from PJ770 on the top board. 2. Remove four M2x10 black flat head screws securing the cooling module. 3. Lift out the cooling module.
Thermal conductor CPU lock 1. Peel off the thermal conductor. 2. Insert a flat head screwdriver and rotate it counter-clockwise to unlock the CPU lock. 3. Lift out the CPU.
MICROPHONE REMOVAL
SD/SOUND BOARD REMOVAL
SD interface cable
PJ1001 Sound interface cable PJ1000
Microphone PJ1003 Microphone cable 1. Disconnect the microphone cable from PJ1003 on the SD/Sound board. 2. Lift out the microphone.
M2.5x4 brass screws SD/Sound board 1. Disconnect the SD interface cable from PJ1001 and sound interface cable from PJ1000 on the SD/sound board. 2. Remove two M2.5x4 brass screws securing the SD/Sound board. 3. Lift out the SD/Sound board.
Tough Enough for Today's World.
TOSHIBA