Text preview for : TECRA 9000 SERIES pt3.pdf part of Toshiba Tecra 9000 I need the service/repair manual, please?
Too big for 1 file, had to split to 3
Back to : TECRA 9000 SERIES pt3.pdf | Home
FIELD REPLACEABLE UNIT DOCUMENTATION
Tecra 9000 Series
RTC BATTERY REMOVAL LED/BLUETOOTH BOARD REMOVAL
TM
M2.5x8 silver screw RTC battery
PJ5
RTC cable
Plastic insulator
LED/Bluetooth board
M2.5x4 brass screws
1. Remove the plastic insulator. 2. Disconnect the RTC cable from PJ5 on the LED/Bluetooth board. 3. Lift out the RTC battery.
1. Remove two M2.5x4 brass screws and one M2.5x8 silver screw securing the LED/Bluetooth board. 2. Disconnect the LED/Bluetooth board from PJ105 on the top PCB.
TOP PCB REMOVAL
Modem cable This is where top and bottom board interconects
PJ801
Sound interface cable PC card slot SD interface cable 4. Remove the PC card slot from PJ117 on the top PCB. 5. Disconnect the following cables from the top PCB: -Sound interface cable from PJ102 -SD interface cable from PJ103 -Modem cable from PJ126
Power cable
M2.5x16 black screw
M2.5x4 brass screws
1. Disconnect the power cable from PJ801 on the top PCB. 2. Remove two M2.5x4 brass screws and one M2.5x16 black screw securing the top PCB. 3. Gently lift up the right side of the top board to disconnect from PJ19 on the top PCB.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Tecra 9000 Series
BOTTOM PCB REMOVAL
M2.5x4 brass screws Membrane switch assy
TM
MEMBRANE SWITCH REMOVAL
Bottom board
PJ18
Battery harness
M2.5x3 silver screws 1. Remove three M2.5x3 flat head silver screws securing the membrane switch. 2. Lift out the membrane switch assembly.
1. Disconnect the battery harness from PJ18 on the bottom PCB. 2. Remove five M2.5x4 brass screws securing the bottom PCB. 3. Lift out the bottom PCB.
SPEAKERS REMOVAL
Left and right speakers
M2.5x4 brass screws 1. Remove four M2.5x4 brass screws securing the left and right speakers. 2. Lift out the speakers.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Tecra 9000 Series
14.1" DISPLAY MASK REMOVAL
Latch Mask seals Mask seals
TM
FL INVERTER AND 14.1" LCD REMOVAL
LCD module
Display mask
LCD
M2x4 brass screws
M2x4 brass screws
Mask seals 1. Remove two mask seals at the bottom corners of the display assembly using a pair of fine-tipped tweezers. 2. Remove two M2.5x6 flat head brass screws securing the display mask. 3. There are 23 latches securing the display mask. Carefully insert your fingers between the mask and the LCD panel and pry open the latches starting from the six top latches, to the five latches on each right and left sides, ending with the bottom seven latches.
LCD/ FL cable
FL inverter board
M2x3 silver screw
FL cable
1. Remove one M2x2.8 silver screw securing the FL inverter board. 2. Carefully lift up the FL inverter board and disconnect the LCD/FL cable from CN1 and the FL cable from CN2. 3. Remove four mask seals to expose four screws securing the LCD module assembly. 4. Remove four M2X2.8 brass screws securing the LCD module assembly. 5. Carefully rotate out the top of the LCD module enough to access the display cable 6. Peel off the tape securing the LCD/FL cable and disconnect the cable. 7. Remove four M2x2.8 silver screws securing the right and left LCD brackets.
Tough Enough for Today's World.
TOSHIBA