Text preview for : en_4n_09.pdf part of Daewoo Nubira/Lacetti Also known as: Chevrolet Nubira / Lacetti, Chevrolet Optra Optra5, Suzuki Forenza Reno
Covers the 1.4L, 1.6L and 1.8L engine.
Year 2004
Back to : Service Manual - Daewoo L | Home
NUBIRA/LACETTI
SEALING, CAULKING AND DEADNER 91
SECTION 9
SEALING, CAULKING AND DEADNER
CONTENTS 1. SEALING & CAULKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 2. DEADNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 14
2.1.GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 914 2.2.REPAIR PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 914
92 SEALING, CAULKING AND DEADNER
NUBIRA/LACETTI
1. SEALING & CAULKING
Note : Seal the following areas to prevent air leaks water leaks, and rust. ENGINE ROOM .
Fig. 1 Engine Room
NUBIRA/LACETTI
SEALING, CAULKING AND DEADNER 93
ENGINE ROOM
Fig. 2 Engine Room
94 SEALING, CAULKING AND DEADNER
NUBIRA/LACETTI
DASH
Fig. 3 Dash
NUBIRA/LACETTI
SEALING, CAULKING AND DEADNER 95
FLOOR & TRUNK ROOM
Fig. 4 Floor & Trunk Room
96 SEALING, CAULKING AND DEADNER
NUBIRA/LACETTI
REAR LAMP & TRUNK ROOM
Fig. 5 Rear Lamp
NUBIRA/LACETTI
SEALING, CAULKING AND DEADNER 97
Fig. 6 Rear Lamp
98 SEALING, CAULKING AND DEADNER
NUBIRA/LACETTI
ROOF
Fig. 7 Roof
NUBIRA/LACETTI
SEALING, CAULKING AND DEADNER 99
ROOF
Fig. 8 Roof
910 SEALING, CAULKING AND DEADNER
NUBIRA/LACETTI
SUN ROOF
Fig. 9 Sun Roof
NUBIRA/LACETTI
SEALING, CAULKING AND DEADNER 911
HOOD & TRUNK LID
Fig. 10 Hood & Trunk Lid
912 SEALING, CAULKING AND DEADNER
NUBIRA/LACETTI
TAILGATE
Fig. 11 Tailgate
NUBIRA/LACETTI
SEALING, CAULKING AND DEADNER 913
FRONT & REAR DOOR
Fig. 12 Front & Rear Door
914 SEALING, CAULKING AND DEADNER
NUBIRA/LACETTI
2. DEADNER
21. GENERAL DESCRIPTION
. Deadner is properly designed and applied for reduce the vibration and noise. Also, it plays in maintaining the structural rigidity of the panel. .
22. REPAIR PROCEDURE
. 1. Remove the related parts. S Seats, carpet. S Trims, others. . 2. Removal of the damaged deadner. S Peel off the damaged deadner with a steel spatula, carefully. . 3. Clean and dry. S Before applying the deadner, thoroughly clean and dry the areas to be applied. . 4. Prelocation the new deadner on the panels to be applied. . Note : Avoid the parts mounting holes and service holes. . 5. Adhension of deadner. S Heat the surface of deadner with a torch or heating gun until it adheres itself. S Push and adhere to the panel with a rubber spatula. . Note : In order to take full advantage of the deadner, its face must adhere and contact the panels perfectly. . CAUTION : Be careful not to burn the composite parts when beating.
Fig. 13 6. Install the related parts. S Install in the reverse order in which they were removed.
Fig. 14
NUBIRA/LACETTI
SEALING, CAULKING AND DEADNER 915
Fig. 15 Deadner Chart