Text preview for : 25gs3-p45~p67(590).pdf part of Philips 25gs3-p45~p67(590) Philips Monitor CD 2001 Monitor CD 2001 E-MANUALS Philips crt 107p2 Pdf 25gs3-p45~p67(590).pdf
Back to : 25gs3-p45~p67(590).pdf | Home
General Product Specification 107P2 CM 25 GSIII 45
Go to cover page
CM25 - 107P2 General Specification (Sheet 590)
FEATURES / BENEFITS
- Extremely high MTBF (over 75K Hours, exclude. CRT).
- User friendly OSD display for mode identification and adjustment
- Professional look, with non-flammable cabinet (94V-0).
- Better display performance.
. Super Flat/square display tube
. Finer CRT dot pitch (0.25 mm)
. Full screen size application
. Real multi - freq.
- Power saving management system.
- VESA DDC1 /2B
- Picture tilt control
- Low emission TCO99
CM25-17" 107P2 92KHz AR CRT
TYPE : 107P20/00H 8639 000 10649
BRAND : PHILIPS
00-06-07
K.C. Huang 23 590 1
00-06-07
Back Forward
46 107P2 CM 25 GSIII General Product Specification
Go to cover page
INDEX
=========
1.0 Introduction
2.0 General description
2.1 General condition
3.0 Electrical characteristics
3.1 Signal interface
3.1.1 Input requirements
3.1.2 Signals input.
3.1.3 Factory pre-set modes
3.2 Timing requirements
3.2.1 Horizontal scanning
3.2.2 Vertical scanning
3.3 Power supply
3.4 Power saving management system
3.5 CRT description
3.6 RGB amplifier
3.6.1 Video amplifier
3.6.2 Brightness and contrast
3.7 Variation of image size
3.8 Degaussing
3.9 Phosphor protection
3.10 Low emission requirements (TCO-99)
3.11 Display data channel : DDC1/2B (VESA STANDARD)
4.0 Display
4.1 Display resolution
4.2 Image size
4.3 Image centering deviation
4.4 Picture shift control range
4.5 Geometric distortions
4.6 Picture tilt
4.7 Image non-linearity
CM25-17" 107P2 92KHz AR CRT
TYPE : 107P20/00H 8639 000 10649
BRAND : PHILIPS
00-06-07
K.C. Huang 23 590 2
00-06-07
Back Forward
GENERAL PRODUCT SPECIFICATION 107P2 CM 25 GSIII 47
Go to cover page
4.8 Mis -covergence
4.9 Focus check
4.10 Luminance uniformity
4.11 White color adjustm ent
4.12 Color tracking on full white pattern
4.13 Purity
4.14 Moire
5.0 Mechanical characteristics
5.1 User controls ( at front)
5.2 Connector and cables
5.2.1 Power Cord
5.2.2 Signal Cable
5.3 Foot Assembly
6.0 Connector and cable
7.0 Environmental characteristics
7.1 Susceptibility of display to external environment
7.1.1 Operation limits
7.1.2 Transportation packages
7.2 Display disturbance from external environment
7.2.1 ESD disturbances
7.3 Display disturbance to external environment
7.3.1 Ionizetic radiation
7.3.2 EMI
8.0 Reliability
8.1 Mean time between failures
9.0 Quality assurance requirements
9.1 Acceptance test
10.0 Serviceability
CM25-17" 107P2 92KHz AR CRT
TYPE : 107P20/00H 8639 000 10649
BRAND : PHILIPS
00-06-07
K.C. Huang 23 590 3
00-06-07
Back Forward
48 107P2 CM 25 GSIII GENERAL PRODUCT SPECIFICATION
Go to cover page
1.0 Introduction
This document is related to the 17" AUTOSCAN color monitor
and max. resolution:
1920 X 1440 by 60Hz refresh rate
2.0 General description
This AUTOSCAN analog colour monitor is specified as a
display peripheral within an IBM compatible PC.
The AUTOSCAN analog colour monitor is to operate at
H: 30 to 92.0 KHz V: 50 to 160 Hz
can be applied to all RGB analog computers within this scanning frequencies.
The AUTOSCAN analog colour monitor is intended to be a
finished product, basically a display device mounted inside
a plastic enclosure which provides the aesthetic, mechanical,
ergonomic and safety requirements.
2.1 General condition
The unit will produce a usable image after switching -on,
measurements are to be carried out with a full stabilized
set after about 30 minutes warm -up at room ambient
temperature of 25