Text preview for : Sharp ARM280 Service Manual.pdf part of sharp ARM280 manual service SHARP ARM280
Back to : Sharp ARM280 Service Manu | Home
CODE : 00ZARM280UA1E
LASER PRINTER
MODEL
AR-M280U/M280N
[1] INTRODUCTION
These models are a modified version of the AR-M350U/M350N, providing a different printing speed. This Service Manual, therefore, describes only the different points from the AR-M350U/M350N and supplementary items. For items which are not described in this Service Manual, refer to the following Service Manuals and Parts Guides. ·AR-M350/M450 ·AR-P350/P450 ·AR-M350U/N·AR-M450U/N ·AR-NC5J Service Manual : 00ZARM350/A1E Service Manual : 00ZARP350/A2E Service Manual : 00ZARM350UA1E Service Manual : 00ZARNC5J/A1E Parts Guide : 00ZARM450/P1E Parts Guide : 00ZAR350LPP1/ Circuit Diagram : 00ZARM350/C1/ Circuit Diagram : 00ZARP350/C1/
Note: Depending on the option, additional service documentation may be required.
[2] LIST OF DIFFERENCES FROM AR-M350U/N
A.Product composition
Model Name Base Engine Print Speed Multi Function Controller Multi Function Controller(for U-Model) Print Server Card Printer Extension Kit Hardware MFP-ROM AR-NC5J AR-P14 AR-M11 Network Printer Option Model AR-M350U 35ppm Not Available Standard Option Option Only U-type 35/45ppm AR-M280U 28ppm Not Available Standard Option Option Only U-type 28ppm NIC Standard Model AR-M350N 35ppm Standard Not Available Standard Standard Only M-type 35/45ppm AR-M280N 28ppm Standard Not Available Standard Standard Only M-type 28ppm *1 No registered as a product Note
*1: Installation of the AR-P14 on U-series machines provides functions equivalent to the M-series machines.
Parts marked with " " are important for maintaining the safety of the machine. To maintain the safety and performance of the machine, use only the replacement parts specified.
SHARP CORPORATION
This document was been published to faciliate after sales service only. The contents are subject to change without notice.
[3] CONFIGURATION
1.System Configurations
Exit tray (AR-TE3 or AR-DU4 Standard) B/W scanner module/DSPF(AR-EF1)
Duplex module/bypass tray(AR-DU4)
Upper exit tray extension (AR-TE4)
Finisher (AR-FN6)
Duplex module (AR-DU3)
Mail-bin stacker (AR-MS1)
Saddle stitch finisher (AR-FN7)
Stand/3 x 500 sheet paper drawer (AR-D14)
Power supply unit (AR-DC1)
Stand/MPD & 2000 sheet paper drawer (AR-D13)
2. Standard
Category MFP model (35ppm) MFP model (45ppm) Model Name AR-M350 AR-M450 Other options required for the installation/mounting. (Options must be ordered separately.) · B/W Scanner module/DSPF (AR-EF1) · Scanner Rack(AR-RK1) · Stand/MPD&2000 sheet paper drawer (AR-D13) or Three paper drawer stand (AR-D14) · Power supply unit (AR-DC1) Remarks
MFP model (28ppm) (Without network printer function) AR-M280U MFP model (35ppm) (Without network printer function) AR-M350U MFP model (45ppm) (Without network printer function) AR-M450U MFP model (28ppm) (With NIC card (standard)) MFP model (35ppm) (With NIC card (standard)) MFP model (45ppm) (With NIC card (standard)) AR-M280N AR-M350N AR-M450N
AR-M280U CONFIGURATION 3-1
3. List of combination of peripheral devices
A.AR-M280U
As shown in the table below, some other peripheral devices ( B ) may be needed for installation of a peripheral device ( A ) and some peripheral devices cannot be installed together.
B
Stand/3 x 500 sheet paper drawer Multi-function controller board B/W scanner module/DSPF Network scanner expansion kit Duplex module/bypass tray
Stand/MPD & 2000 sheet
Upper exit tray extension
Facsimile expansion kit Fax memory (8 MB)
Saddle stitch finisher
Related for scanner feature B/W scanner module/DSPF Scanner rack AR-EF1 AR-RK1
*1 *1
Related for paper feed unit Stand/3 x 500 sheet paper drawer Stand/MPD & 2000 sheet paper drawer AR-D14 AR-D13 *1 *1 *2 *2
Duplex module/bypass tray AR-DU4 Duplex module Output units Saddle stitch finisher Finisher AR-FN7 AR-FN6 AR-MS1 *4 AR-TE3 AR-TE4 AR-PN1 AR-DU3
*1 *1 *1 *1 *1
A
Mail-bin stacker Exit tray Upper exit tray extension Punch unit Related for extension of functions and others PS3 expansion kit Network scanner expansion kit Facsimile expansion kit Fax memory (8 MB) Power supply unit Hard disk drive
AR-PK1 AR-NS2 AR-FX5 AR-MM9 AR-DC1 AR-HD3 *1 *1 *1 *1 *1 *1
Multi-function controller *5 AR-M11 board Print server card Network printer kit *6 AR-NC5J AR-P14
= Must be installed together. *1 = Any of the units must be installed together. *2 = Must be installed for installation of the stand/3 x 500 sheet paper drawer or the stand/MPD & 2000 sheet paper drawer. = Cannot be installed together. *3 = Standard *4 = AR-DU4 Standard *5 = Attachment of the AR-P14 provides the similar functions. *6 = Not Available
AR-M280U CONFIGURATION 3-2
Hard disk drive Network printer kit
PS3 expansion kit
Print server card
Mail-bin stacker
Punch unit
Exit tray
Finisher
Power supply unit
Duplex module
Scanner rack
B.AR-M280N
As shown in the table below, some other peripheral devices ( B ) may be needed for installation of a peripheral device ( A ) and some peripheral devices cannot be installed together.
B
Stand/3 x 500 sheet paper drawer Multi-function controller board B/W scanner module/DSPF Network scanner expansion kit Duplex module/bypass tray
Stand/MPD & 2000 sheet
Upper exit tray extension
Facsimile expansion kit Fax memory (8 MB)
Saddle stitch finisher
Related for scanner feature B/W scanner module/DSPF Scanner rack AR-EF1 AR-RK1
*1 *1
Related for paper feed unit Stand/3 x 500 sheet paper drawer Stand/MPD & 2000 sheet paper drawer AR-D14 AR-D13 *1 *1 *2 *2
Duplex module/bypass tray AR-DU4 Duplex module Output units Saddle stitch finisher Finisher AR-FN7 AR-FN6 AR-MS1 *4 AR-TE3 AR-TE4 AR-PN1 AR-DU3
*1 *1 *1 *1 *1
A
Mail-bin stacker Exit tray Upper exit tray extension Punch unit Related for extension of functions and others PS3 expansion kit Network scanner expansion kit Facsimile expansion kit Fax memory (8 MB) Power supply unit Hard disk drive
AR-PK1 AR-NS2 AR-FX5 AR-MM9 AR-DC1 AR-HD3 *1 *1 *1 *1 *1
Multi-function controller *3 AR-M11 board Print server card Network printer kit *3 AR-NC5J *6 AR-P14
= Must be installed together. *1 = Any of the units must be installed together. *2 = Must be installed for installation of the stand/3 x 500 sheet paper drawer or the stand/MPD & 2000 sheet paper drawer. = Cannot be installed together. *3 = Standard *4 = AR-DU4 Standard *6 = Cannot be attached.
AR-M280U CONFIGURATION 3-3
Hard disk drive Network printer kit
PS3 expansion kit
Power supply unit
Print server card
Mail-bin stacker
Duplex module
Scanner rack
Punch unit
Exit tray
Finisher
[4] SPECIFICATIONS
1. Basic Specification
A. Base Engine
(1) Form
AR-M280U/M280N Console type
(in mm) Paper size A3 B4 A4 B5 A5 Japanese postcard AR-M280U/N Ledger Legal Foolscap Letter Executive Invoice Com-10(envelope) C5(envelope) Monarch(envelope) DL(envelope) ISO B5(envelope) A 297 257 210 182 148 100 279 216 216 216 184 140 105 162 98 110 176 B 420 364 297 257 210 148 432 356 330 279 267 216 241 229 191 220 250 C 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 D 289 242 202 168 140 92 271 208 208 208 183 132 97 154 90 102 168 E 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
(2) Engine speed
Paper size A4, 8.5" x 11" A5R/5.5" x 8.5"R B5 B4/8.5" x 14 A3/11" x 17" 28ppm 28ppm 28ppm 16ppm 14ppm
(3) Engine composition
Photoconductor type Record method Development method Charge method Transfer method Cleaning method Fusing method Used toner disposal Resolution Smoothing Gradation OPC (diameter of photoconductor : ø30mm) Electrophotograph (laser) Dry-type dual-component magnetic brush development Charged saw-tooth method Transfer roller Cleaner blade Heat roller Toner recycling system
(6) Warm-up
Warm-up time Pre-heat requirement Jam recovery time less than 80 seconds Required Target: about 30 seconds (Under standard condition of 60 seconds left after side cover opening, polygon motor halt) 100V system 100-127V 50/60Hz
(4) Engine resolution
Write :600dpi Write :1200dpi equivalent Write :2 levels
(7) Power source
Voltage Frequency
(5) Printable area
The print area of this product is shown below.
E
(8) Power consumption
Max. Power consumption. 1440W(When MFP full system)
C
C
(9) Energy Star benchmark
Low power mode Transition time to low power mode 30W or below 30min
(10) Noise
B
At working At waiting mode * less than 6.8B less than 5.0B
Showing noise benchmark in each model as a whole system. 428x552x469 (Only main unit) (mm) 16.9"x21.7"x18.5" 963x685 (mm) *1 25.7"x22.3" AR-M280U:Approx.38.9kg (including developing unit/process/ each controller) Approx.99kg *1 AR-M280N:Approx.39.9kg (including developing unit/process/ each controller/NIC) Approx.100kg *1
(11) Dimensions
External dimensions (WxDxH) Occupied space dimensions (WxD) Weight
E
D A Paper size Printable area
If a printer driver for Windows or Macintosh is used for printing, the printable area will be smaller. The actual printable area depends on the printer driver to be used.
*1:
With B/W scanner module/DSPF, Scanner rack, Large capacity paper feed desk, Power supply unit and Upper exit tray extension
AR-M280U SPECIFICATIONS 4-1
B. Document Feeding Equipment
(1) One-drawer tray (included in the base engine)
Paper feed method Sizes to be fed Paper capacity Media available for paper feeding Paper type Paper size switching One-drawer tray A4, B5, 8.5" x 11" 500 sheets (at 80g/m²) Plain paper 60 - 105g/m², 16 - 28lbs Plain, recycled, pre-printed, pre-punched, color, letter head To be switched by user (paper size to be entered from the operation panel). Not provided
(4) Print Function
a. General When an optional PS3 expansion kit is installed Function Copies Orientation Duplex print Saddle stitch Binding edge N-up N-up direction N-up border line b. Paper input When an optional PS3 expansion kit is installed Function Paper size Custom paper size Source selection Different first page PCL5e/ PCL6 Yes 1 size Yes Yes PS Yes 1 size Yes Yes Yes PPD (Windows) Yes 3 sizes*3*5 Yes N/A N/A PPD (Macintosh) Yes N/A Yes Yes Yes PCL5e/ PCL6 1 - 999 Yes Yes Yes Left/top/ right 2/4/6/8 Fixed Yes PS 1 - 999 Yes Yes Yes Left/top/ right 2/4/6/8 Fixed Yes PPD (Windows) 1 - 999 Yes Yes No Long/short 2/4*3*4 Fixed PPD (Macintosh) 1 - 999 Yes Yes N/A Long/short 2/4/6/9/16 Selectable
Dehumidification heater Balance detection Default size setting
Provided (paper empty and 3 steps) 100V system 200V system 8.5" x 11" A4 Mounting/dismounting Provided of the tray
Yes(always) Yes
C. Output Equipment
(1) Face-down Exit Tray (included in the base engine)
Output position/ method Output paper capacity Output paper size Face-down output at the upper side of main unit 400 sheets (80g/m² sheet) A3, B4, A4, A4R, B5, B5R, A5R 11 " x 17", 8.5" x 14", 8.5" x 13", 8.5" x 11 ", 8.5" x 11 "R, 5.5" x 8.5"R Executive, postal card, Monarch (98 x 191) Com-10 (105 x 241), DL (110 x 220), C5 (162 x 229), ISO B5 (176 x 250) Tracing paper : 52 ~ 59g/m² / 14 ~ 15lbs Plain paper : 60 ~ 128g/m² / 16 ~ 34lbs Index paper : 176g/m² / 47lbs Cover paper : 205g/m² / 54 ~ 55lbs Transparency film Not provided Provided
Transparency inserts Yes c. Paper output
When an optional PS3 expansion kit is installed Function PCL5e/ PCL6 Yes Yes Yes Yes PS Yes Yes Yes Yes Yes PPD (Windows) Yes Yes Yes Yes Yes PPD (Macintosh) Yes Yes Yes Yes Yes
Spec of media for paper output
Output tray selection Yes Mail bin Staple Offset Punch d. Graphic
Remaining paper detection Exit tray full detection
When an optional PS3 expansion kit is installed
2. Specific Function
A. Printer Function
(1) Platform
IBM PC/AT (Include compatible machine) Macintosh (680x0), Power Macintosh, iMac, G3Macintosh * For Macintosh OS, the PS3 expansion kit and NIC card are required. Windows 95/98/Me/XP Windows NT 4.0 Windows 2000 Windows 95/98/Me/XP Windows NT 4.0 Windows 2000 Windows 95/98/Me/XP Windows NT 4.0 Windows 2000 Mac OS 8.5.1 - Mac OS 9
Function Resolution Halftone Graphic mode Smoothing Toner save Photo enhancement Negative image Mirror image Zoom Fit to page e. Font
PCL5e/ PCL6 600/300 dpi N/A Yes Yes Yes Yes*8 N/A N/A N/A Yes
PS 600 dpi Yes N/A Yes Yes Yes Yes Horizontal/ vertical N/A Yes
PPD PPD (Windows) (Macintosh) 600 dpi Yes N/A Yes Yes N/A Yes 600 dpi N/A N/A Yes Yes N/A Yes
(2) Support OS
Custom PS
Custom PCL5e/6(XL) SPDL PPD
Horizontal Yes Yes N/A Yes N/A
When an optional PS3 expansion kit is installed Function Resident font Download font PCL5e/ PCL6 45 fonts Bitmap TrueType, Graphic PS 136 fonts Bitmap Type1 TrueType PPD (Windows) 136 fonts*6 Bitmap Type1 TrueType PPD (Macintosh) 35 fonts N/A
*
For Macintosh OS, the PS3 expansion kit and NIC card are required.
(3) PDL emulation
PCL6, PCL5e compatible, PostScript Level 2, PostScript 3 compatible (PS3 expansion kit is required.)
AR-M280U SPECIFICATIONS 4-2
f. Others When an optional PS3 expansion kit is installed Function Watermark*7 Overlay Job retention*1 Account control Custom settings Automatic configuration*2 Job end notification PCL5e/ PCL6 Yes Yes Yes Yes Yes Yes Yes PS Yes Yes Yes Yes Yes Yes Yes PPD PPD (Windows) (Macintosh) Yes N/A N/A N/A N/A N/A N/A Yes N/A Yes Yes N/A Yes
(As of March / 2001) Manufacture Capacity Kingston Technology Viking Components 128MB 128MB 256MB 64MB 64MB 128MB 128MB 256MB N/A Memory Card 64MB Technology 128MB Model name KVR133X64C3/128 RAM CHIP name HYB39S64800BT-7.5 Note
KVR133X64C3-128 D456821G-A75-9JF KVR133X64C3-256 HY57V28820AT-H VIK8641CL2 VIK8641CL2 VIK6642CL2 VIK6642CL2 VIK2642CL2 DM864VS65804X7G µPD456841G5 -A80-9JF D456841G5-A80-9JF TC59SM708FT-80 D4564841G5-A80 -9JF TC59SM708FT-80 GM72V66841XT75
* 1 For models without a hard disk drive, an optional hard disk drive (AR-HD3) must be installed . * 2 Functions when peripheral devices are installed. * 3 Not supported in the Windows NT 4.0 environment. * 4 2/4/6/9/16 is supported in the Windows 2000 environment. * 5 Only one size is supported in the Windows 2000 environment. * 6 Only 35 fonts are supported in the Windows NT 4.0 environment. * 7 This function is limited for PPD. * 8 PCL6 only
DM1665VS65804X- HY57V64820HG 7G
C. Scanner function
*Scanner function, the NIC card and Network Scanner kit are required.
(1) Scanner function
Scanner mode Scan to E-mail (Internet FAX) Scan to Server (Client PC) SMTP server FTP server TCP/IP TIFF, PDF, TIFF-F * Selectable for each page Uncompressed, G3(1-dimension) *1, G4 *2 *1 G3 (1-dimension) = MH (Modified Huffman) *2 G4 = MMR (Modified MR)
(2) Support System (5) Compatibility
PCL 5e compatibility Target for PCL5e is to be compatible with HP LaserJet 4000. Small margin difference, rendering difference by different font family, default and transfer function difference are not to be included in the compatibility. All the PJL commands are not necessarily included in the compatibility. Target for PCL6 is to be compatible with HP LaserJet 4000. Small margin difference, rendering difference by different font family, default and transfer function difference are not to be included in the compatibility. All the PJL commands are not necessarily included in the compatibility. Roman PostScript is targeted to be compatible with Adobe PostScript as performed in HP LaserJet 4000. Small margin difference, rendering difference by different font family, default and transfer function difference are not to be included in the compatibility. Embedded server Protocol
(3) Support Image
Format Compression method
PCL6 compatibility
(4) Transmission Mode
DSPF/OC Available transmission switching (Switching during the reading is not possible)
PostScript Compatibility
(5) Image Process
Half tone reproduction Exposure adjustment Quality selection Resolution* Equivalent to 256 levels Light / Auto / Dark Half-tone ON/OFF Normal ( 200x200dpi ) Fine ( 300x300dpi ) Super fine ( 400x400dpi ) Ultra fine ( 600x600dpi ) Varies with the file type/transmission method Commonly use ERDH area of memory. Special : As per ERDH memory Specifying by one-touch or group Max. 500 destinations (in conjunction with the one-touch dial of FAX) Max. 100 destinations can be registered for FTP and Desktop. To be registered in one-touch Available
B. Expanded RAM
Installation of additional RAM will provide the following: 1) Time out error reduction 2) Spool time reduction 3) Avoidance of Virtual Memory (VM) error / memory full Use commercially available RAM with the following specifications. Note: If RAM used does not meet the follow specifications, the copier may not recognize the additional RAM or its capacity correctly. DIMM TYPE DIMM capacity CAS LATENCY SPD Parity ECC 168pin 3.3V Unbuffered SDRAM DIMM Non-ECC 64MByte, 128MByte, 256MByte CL=2 Supporting Not support Not support Group* Program
(6) Original Memory
Standard Memory expansion Specified destination One-touch*
(7) Specified Destination
SDRAM CLOCK For PC100, PC133
(8) Specified Multiple Destinations
Specified destination Specifying by one-touch or group No. of registration Max. 300 items (in conjunction with those of FAX) Sequential Available broadcasting (E-mail only. It is not available for FTP/Desktop.) Simultaneous FAX Available transmission (Specifying multiple destinations of FAX, E-mail or FTP and broadcasting by a single scan) O : Available AR-M280U SPECIFICATIONS 4-3
(9) Functions
Transmitting Rotating transmission functions Long length original transmission Verification stamp function Transmit/receive record Transmit/receive result Address/phone directory list Group list ID/sender list Program list Available (to be matched with FAX specification) Not Available Option Available Available Available Available Available Available
(6) Exposure/Copy Quality Process
Exposure mode Manual steps Smoothing Toner save mode Binary: Text(auto/manual), Text/photo, Photo 256 levels: Not provided 9 steps Standard Standard
Report/list functions
(7) Copy Function
Function APS AMS Paper type select Standard Function Standard Function Standard Function (By type setting) Auto tray switching Standard Function Rotation copy Standard Function Electronic sort Standard Function Rotation sort Not provided Reserved copy Standard Function Prior tray setting Not provided Recall/register of program Standard Function Proof copy Not provided Preheat function Standard Function (To be set up by key operator) Auto power shut-off function Standard Function (To be set up by the key operator program) Account control Standard Function (100 accounts) Communication support (RIC) Standard Function Card counter support Only provided the connector Coin vendor support Only provided the connector Margin shift Standard Function Edge erase / Center erase Standard Function Dual page copying Standard Function Covers Not provided Transparency insert Not provided Centering Not provided Multi shot (N in 1) Standard Function (2 in 1 / 4 in 1) Pamphlet copy Standard Function 2-sided copy orientation change Standard Function Large capacity original mode 0 (Max. 140 pages) B/W reverse Not provided Shading Not provided Mirror image Not provided Repeat Not provided Date stamp Not provided Stamp Not provided Page stamp Not provided Zaurus print Not provided
D. Copy function
(1) Copy Speed
Actual A4, 8.5"x11" A4R, 8.5"x11"R A5R, 5.5"x8.5"R, Invoice-R B5 B5R, Exective-R B4, 8.5"x14" A3, 11"x17" Extra, Envelope Japan P/C 28 20 28 28 20 16 14 14 Reduction 28 20 28 28 20 16 14 14 Enlargement 28 20 28 28 20 16 14 14
When printing on post cards, engine speed can vary with system configuration, because each card is fed only after the previous card exits machine. Special function
*
Figures in reduction/enlargement are represented by those at the ratio to show slowest speed
(2) First Copy Time
Conditions: A4 or 8.5"x11"P from front tray of PPC, without HDD and with polygon motor running. Document glass *1 DSPF *1 Less than 5.3 seconds Less than 6.0 seconds
During OC/high-speed mode 27 cpm (97%) 26 cpm (92%) 26 cpm (92%) original 5 sheets copy 5sets original 10 sheets copy 5sets original 5 sheets (10 pages) copy 5sets
(3) Job Speed
S S D S D D *1 *2 *3
*1 S *2 S *3 D
S : A4 / 8.5" x 11"P D : A4 / 8.5" x 11"P D : A4 / 8.5" x 11"P
Note: First copy time has been factored into calculation resulting in reduced CPM.
(4) Continuous Copy
Max. multiple number 999 pages
(5) Copy Ratio
Copy ratio AB series : 25%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 400% Inch series : 25%, 64%, 77%, 100%, 121%, 129%, 400% Zoom 25 - 400% 25 - 200% (Copy from DSPF) Independent Not provided scaling
AR-M280U SPECIFICATIONS 4-4
[5] CONSUMABLE PARTS
1.Supply system table
Note: The consumable parts are the same as those of the AR-M350/M450 series and the AR-P350/P450.
A.USA
NO Name 1 Toner (Black) 2 3 4 Developer Drum Maintenance kit 1 Content Toner(Toner : Net Weight 814g) Developer(Developer : Net Weight 450g) Drum Cleaner blade Drum separation pawl Screen grid Toner reception seal Side molt F Side molt R Charging plate Transfer roller Discharging plate Paper dust removing unit DV blade DV side seal F DV side seal R Upper heat roller Fusing separation pawl (Upper) Lower heat roller Fusing separation pawl (Lower) Cleaner blade Cleaning roller Bearing Staple cartridge Staple cartridge Life 27K 80K 80K 80K *2 Product name Remark AR-450NT *Life setup is based on A4 6% (*1 AR-450NT-J) AR-450ND AR-451DR AR-450KC1
5
Maintenance kit 2
6 7 8 9
Upper heat roller kit Lower heat roller kit Cleaner blade Cleaning roller
x1 x1 x4 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 x4 x1 x2 x10 x10 x20 x3 x3
80K
AR-450KA1
160K 160K 80K*2(x10) 160K(x10) 3000x3 5000x3
AR-450UH AR-450LH AR-450CB AR-450CR AR-SC1 AR-SC2 Available in the National Parts Center Available in the National Parts Center Common with cartridge for AR-FN4 & AR-FN6 Common with cartridge for AR-FN7
10 Staple cartridge 11 Staple cartridge *1: *2:
For USA Equivalent to the drum life.
Note1: Print on Master/individual carton:Toner/Developer in 2 languages (English/French), DR in 4 languages (English/French/German/Spanish). Note2: Packed with machine: DR 80K/Developer UN/Process UN Note3: The other maintenance parts which are not listed above are registered as service parts.
AR-M280U CONSUMABLE PARTS 5-1
2.Production number identification
A. Drum cartridge
The lot number, printed on the front side flange, is composed of 10 digits, each digit showing the following content: 1 1 2 2 3 4 5 6 7 8 9 10 1 Number For this model, this digit is 2. Alphabet Indicates the model conformity code. S for this model. (100K/80K drum) Number Indicates the end digit of the production year. Number or X, Y, Z Indicates the production month. X stands for October, Y November, and Z December. Number Indicates the production day on the month. Number or X, Y, Z Indicates the month of packing. X stands for October, Y November, and Z December. Number Indicates the day of the month of packing. Alphabet Indicates the production factory. "A" for Nara Plant. 1 2 3/4 5/6 7 8 2 3 4 5 6 7 8
C. Developer
The lot number is composed of 8 digit, and each digit indicates as following. The lot number shall be printed on the bag.
3 4
5/6 7
Alphabet Indicates the production factory. Figure Indicates the production year. Figure Indicates the production month. Figure Indicates the production day. Hyphenation Figure Indicates the production lot.
3. Environmental conditions
A. Operating conditions
30 85%
8/9 10
85
B. Toner cartridge
The lot number is composed of 7 digits, and each digit indicates as following. The lot number shall is printed in the position shown below. 1 1 2 3 4 5,6 7 2 3 4 5 6 7
Humidity (%)
35
60%
20
Version number (A - sequentially revised) Numeral figure Indicates the end digit of the production year. Alphabet Indicates the production factory. (B for SOCC) Destination code Numeral figures Indicates the production day. Numeral figure or X, Y, Z Indicates the production month. X stands for October, Y November, and Z December.
10
Temperature
35
(Without dew condensation)
B. Storage conditions
90
Lot No. Location
Humidity (%)
20 -10
Temperature
40
(Without dew condensation)
Lot No. Location
Heat seal
Aluminum bag
AR-M280U CONSUMABLE PARTS 5-2
4.Different point of 50K drum and 80K drum
1 2 3 4 Marking Lot number Flange assembly direction Color band on Drum 50K drum No mark on Flange 2 digit : [ T ] Painting upper limit : F side Green 80K drum White paint mark on rear side of Flange 2 digit : [ S ] Painting upper limit : R side Silver
White paint mark
100k (80k) drum
Silver
50k drum
Green
AR-M280U CONSUMABLE PARTS 5-3
[6] UNPACKING AND INSTALLATION
1. Installing procedure flowchart
There are many combinations between this machine and option units. For installing option units, observe the following procedures for efficiency. To install the devices efficiently, follow the procedure below. Some peripheral devices may have been installed as standard devices depending on the main unit model. Part of descriptions and illustrations may be different.
Scanner/document feeder device Finishing device Duplex/bypass device Scanner/document feeder device Finishing device
Main unit
Finishing device
Main unit
Duplex device
Paper feeding device
Paper feeding device
Start of installation
Main unit, paper feeding device, and power supply unit.
AR-D13 /AR-DC1 AR-D14 /AR-DC1
Install controller board, facsimile unit or other electric devices. Controller board, facsimile unit or other electric devices installed? No [Electrical setting/adjustment] Install duplex / bypass device. Yes
AR-HD3 AR-FX5/AR-MM9 AR-PK1 AR-NS2 AR-NC5J
(Not required for the AR-M350N/M450N)
Main unit
AR-P14
(Only AR-M350U/M450U)
Extended memory
Duplex/bypass device installed?
Yes AR-DU3 AR-DU4
1) Installation of driver software, setting, and operation check Main unit/AR-EF1/AR-NC5J/AR-HD3/ AR-FX5/AR-PK1/AR-NS2/AR-P14 2) Paper guide position adjustment/off center adjustment
No Install finishing device. Finishing device installed? Yes AR-MS1/AR-DC1 AR-FN6 /AR-DC1 AR-FN7 AR-PN1A / B / C / D
AR-D13/AR-D14/ AR-DU3/AR-DU4
No
End
Scanner/document feeder installed?
Yes
Install scanner/document feeder.
* AR-EF1 /AR-RK1
No
When installing a paper feeding device, an optional power supply unit or a duplex/bypass device, be sure to re-attach the rear cabinet, the AC inlet cover, and the harness cover of the main unit at the end of installation as needed. When installing a controller board, a facsimile unit, and other electric devices, be sure to install them one at a time. Only off center adjustment is needed for AR-DU3.
*
When installing an option, refer to the Service Manual for that option and or the AR-M350 / M450 Service Manual.
AR-M280U UNPACKING AND INSTALLATION 6-1
2. AR-P14 installing procedure
* * This installation procedure is provided for use with the AR-M280U / M280N and AR-M350U / M450U series. To connect this machine to a network, a Print Server Card (NIC) ARNC5J must be installed to the multi-function controller board in advance.
<3>Remove the control PWB unit. Remove the five screws that fix the control PWB unit to the main unit of the printer. Then, hold the two grips and pull out the control PWB unit to remove it from the main unit.
*
To enable the printer expansion function, the product key must be acquired. <4>Mount the printer expansion kit ROMs(2 pcs.)to the control PWB. Remove the ROMs(main and boot ROMs)from the control PWB and replace them with the two ROMs(main and boot ROMs)of the printer expansion kit. The main and boot ROMs are indicated with "MAIN" and "BOOT" on the labels on the ROMs respectively. When mounting the printer expansion kit ROMs, insert them to the same positions in the same direction as those before replacement and ensure that the inserted printer expansion kit ROMs are locked with the fittings of the sockets.
The application number, machine serial number, and product key number are important information. Keep the above information for future reference. 1) Mount the printer expansion kit ROMs to the control PWB. <1>Turn off the main switch of the main unit of the printer Turn the main switch located on the front side of the main unit to the "OFF" position. If the machine is equipped with a facsimile unit, also turn off the FAX power switch. Then remove the power plug from the outlet. .
<2>Remove the cables connected to the control PWB unit. Remove all the cables connected to the control PWB unit of the main unit of the printer.
<5>Re-attach the control PWB. Attach the control PWB to the main unit of the printer and fix it using five screws.
AR-M280U UNPACKING AND INSTALLATION 6-2
<6>Connect the cables to the control PWB. Connect all the cables that have been removed in <2> to the original positions of the control PWB unit.
3) Prepare to enable the printer expansion function. To enable the printer expansion function, use the keys on the operation panel to enter the product key. For entry of the product key, see the key operator's guide of the operation manual for the main unit. Carry out the network setting for the Print Server Card. Use a key operator program to carry out the network setting for this machine. For this network setting, the customer's network environment must be checked. Consult the network administrator to carry out the setting. In addition to the network setting for this machine, to use the machine in the network environment: According to the customer's network environment, install the driver software from the CD-ROM supplied with this machine and use the utility software supplied with the Print Server Card to set the network printer for the server computer. For installation in the server computer and network setting, see the operation manual supplied with the main unit. This setting must be carried out by the network administrator or based on consultation with the network administrator. 4) To check the operation of the printer expansion function. When the network settings and the driver settings are complete, perform a test print to check if printing can be performed successfully. (When test printing is completed successfully, use the "list print" key operator program to print the network settings and keep the printout for future reference.) Installation of AR-P14 is now complete.
If another peripheral device must be installed, carry out the following steps at the end of the installation work. 2) Turn on the main switch of the main unit of the printer. Insert the power plug of the main unit of the printer to the outlet. Then, turn the main switch located on the front side of the main unit to the "ON" position. If the machine is equipped with a facsimile unit, turn on the FAX power switch.
AR-M280U UNPACKING AND INSTALLATION 6-3
[7] MAINTENANCE
1. Self print of set values
Use SIM 22-6 to print the set values (machine settings) and jam history. These values must be printed before execution of maintenance or disassembly procedures.
2. Maintenance System Table
The maintenance items and positions are the same as those of the AR-M350 series. However, the maintenance cycle differs.
A. Scanner / DSPF
Maintenance cycle : 80K X Check (Clean, replace, or adjust as necessary.) O Clean When calling O O O Replace Adjust Lubricate Move position
Unit name
Part name
80k O O O X
160k O O O X
240k O O O X
320k O O O X Note 1 Note 1 Note 1
Remark
Optical section Mirror/Lens/Reflector/Sensors Table glass/OC White reference sheet Rails Drive belt/Drive wire/Pulley DSPF Paper feed section Take-up roller Separation pad Paper feed roller Transport section PS roller Exposure section (Dust-proof glass) Paper exit section Other Finish stamp section [Option] (Japan only) Paper feed roller SPF Sensors Stamp solenoid Stamp individual part
O O O O O O O O O O O O O O O O O O O O O O
For cleaning, blow air. User replacement at 10K or 1 year.
X
X
X
X
X
Note 1: Replacement reference: Same as above or 2 years.
AR-M280U MAINTENANCE 7-1
B. Engine section
* For disassembly procedures, refer to the AR-P350/P450 Service Manual. Maintenance cycle : 80K O Check (Clean, replace, or adjust as necessary.) X Clean When calling Replace Adjust Lubricate Move position
Unit name Drum peripheral Drum
Part name
80k
160k
240k
320k
Remark Installed when shipping
Cleaner blade Toner reception seal Side molt Transfer roller Discharge plate TR bearing (F/R) After-transfer star ring TR gear Screen grid Drum separation pawl UN Charger case (M/C) Charging plate (saw teeth) Developing section Developer DV blade DSD collar DV side seal F DV side seal R Toner cartridge Attached when installing./ EX Japan: 814g, user replacement for every 27K. O O X X X X O O X O X O O X X X X O X O X Clean and remove paper dust. O O O O (O)X Supplied when installing O O O O X (O)X X X X X X X X X X X
Fusing section
Upper heat roller Lower heat roller Upper separation pawl Lower separation pawl Thermistor Upper heat roller gear Paper guides Gears Cleaning roller CL roller collar
Filters Paper feed section
Ozone filter Paper feed roller Torque limiter O X O O O X X O O O X X O O O X X O O O X X O O O (Specified position) X X Sensors X X X X X X X X Note 2 Note 2
Transport section PS follower roller Paper exit reverse section Transport rollers Transport paper guides Paper dust remover Drive section Image quality Other Gears Belts
Note 2: Replacement reference: Use the counter value of each paper feed port as the replacement reference. Paper feed roller/Torque limiter section: 80K or 2 years
AR-M280U MAINTENANCE 7-2
C. Peripheral devices
Maintenance cycle : 80K O Check (Clean, replace, or adjust as necessary.) X Clean When calling (O)X (O)X (O)X O O Replace Adjust Lubricate Move position
Option name ADU + Manual feed
Part name Paper feed Paper feed separation section rollers Separation pad Torque limiter Transport section Transport rollers Transport paper guides Drive section Other Gears Belts Sensors
80k X X X O O
160k X X X O O
240k X X X O O
320k X X X O O Note 3 Note 3 Note 3
Remark
(Specified position) X X (O)X (O)X O O X X X O O X X X O O X X X O O X X X O O (Specified position) X X O (O)X O X O X O X O X O X O X O X O X O (Specified position) X X X X X X X X X X X Replace Unit at 100K staple. User replacement for every 3000pcs. Note 3 Note 3
Desk Paper feed Paper feed (Multi stage LCC) separation section rollers Multi purpose Torque limiter Transport section Transport roller Transport paper guides Drive section Other Finisher Transport section Gears Belts Sensors Transport rollers De-curler roller Transport paper guides Drive section Other Staple unit Staple cartridge Mail-bin stacker Transport section Transport roller Transport paper guides Drive section Other Saddle finisher Transport section Gears Belts Sensors Discharge brush Transport roller Transport paper guides Drive section Other Staple Unit Gears Belts Sensors Discharge brush Gears Belts Sensors Discharge brush
O O
O O
O O
O O
O O (Specified position)
X X X O O X X O O X X O O X X O O X X O O (Specified position) X X X X X X X X X X X Replace Unit at 100K staple (including the staple UN and the holder section). User replacement for every 5000 pcs.
Staple cartridge Note 3: Replacement reference: Use the counter value of each paper feed port as the replacement reference Paper feed roller / Torque limiter section: 80K or 2 years
AR-M280U MAINTENANCE 7-3
[8] ADJUSTMENTS
1. Process section
A. High voltage output adjustment
(1) Developing bias output check and setup
1) Remove the rear cabinet to allow checking of the high voltage monitor output pin. 2) Execute the simulation of the target high voltage. (See the table below.) 3) Select the mode to be set with 10-key, and press START key. 4) Enter the set value with 10-key and press START key. The set value is outputted for 30 sec. 5) Apply a high voltage tester between the measurement pin and the frame. Note: Take care not to short the measuring pin to the frame.
6) The unit stops after 30 sec of output.
Default Monitor output voltage MC grid MAIN GRID (SIM 8-2) AUTO MIX PHOTO PRINTER FAX Transfer current THV+ (SIM 8-6) FRONT BACK Developing bias DV BIAS (SIM 8-1) AUTO MIX PHOTO PRINTER FAX PLUS Separation voltage SHV (SIM 8-17) FRONT BACK Transfer voltage THV (SIM 8-17) AE mode Text/Photo mode Photo mode Printer mode Fax mode Front Back AE mode Text/Photo mode Photo mode Printer mode Fax mode Positive bias Front Rear -500V±5V -500V±5V -500V±5V -500V±5V -500V±5V -500V±5V +150V±5V +1.25V±0.1V +1.25V±0.1V -800V±10V -650V±5V -650V±5V -650V±5V -650V±5V -650V±5V -650V±5V CHARACTER Text mode Set value 645 645 645 645 645 645 45PPM : 267 28/35PPM : 220 45PPM : 310 28/35PPM : 267 485 485 485 485 485 485 150 45PPM : 160 28/35PPM : 120 45PPM : 160 28/35PPM : 120 780
Set range
Measurement pin CN2-7
High voltage probe impedance 100M
200~900 200~900 200~900 200~900 200~900 200~900 0~620 0~620 0~745 0~745 0~745 0~745 0~745 0~745 0~255 0~375 0~375 0~1250
CN2-1
100M
CHARACTER Text mode
CN2-3
10M
CN2-5
10G
2. Engine section
A. Resist quantity setup
·This adjustment requires a high level of accuracy. We recommend using the default setting. This adjustment is performed in the following cases: ·When the void quantity is changed by the paper feed tray. ·When paper is skewed. Complete the following adjustments before performing resist quantity setup. ·LSU right angle adjustment ·Print magnification ratio adjustment ·Print off-center setup ·Void area setup 1) Execute SIM 51-2. 2) Adjust the resist quantity so that paper transport is stable. 45PPM BPT T1 T2 DESK ADU BPT T1 T2 DESK ADU 55 60 50 50 50 60 65 55 55 55
28/35PPM
AR-M280U ADJUSTMENTS 8-1
[9] SIMULATION
The following simulations have been changed. Main code 8
8-17
Operation test, check Used to set and check the transfer roller output. Process (OPC drum, developing, transfer, cleaning) Item Operation Operation/Procedure Enter the output value to be adjusted with 10 digit key pad. The current set value is highlighted at the right of each item. After entering the value with 10 digit key pad, press START key. The output is made for 30sec at the set value. Then the output is stopped. Purpose Function (Content) Section
8-6
Purpose Function (Content) Section Adjustment Used to check and adjust the transfer charger current and its control circuit. Process (OPC drum, developing, transfer, cleaning)
Item Operation/Procedure Enter the output value to be adjusted with 10 digit key pad. The current set value is highlighted at the right of each item. After entering the value with 10 digit key pad, press START key. The output is made for 30sec at the set value. Then the output is stopped.
SIMULATION 8-6 THV+SETTING. SELECT 1-2, AND PRESS START. 1. FRONT 140 2. BACK 140
SIMULATION 8-17 TRANSFER ROLLER SETTING. SELECT 1-3, AND PRESS START. 1. SHV FRONT 500 2. SHV BACK 500 3. THV- 500 Press [CUSTOM SETTING] key.
1
Press [START] key.
1
SIMULATION 8-17 TRANSFER ROLLER SETTING. INPUT VALUE, AND PRESS START. 1. FRONT (0-375)
Press [START] key.
Press [CUSTOM SETTING] key.
500
SIMULATION 8-6 THV+SETTING. INPUT VALUE, AND PRESS START. 1. FRONT(0-620)
Press [START] key.
Press [CUSTOM SETTING] key. Or after 30sec output
140
Or after 30sec output SIMULATION 8-17 TRANSFER ROLLER SETTING. EXECUTING... 1. FRONT (0-375)
Press [START] key.
Press [CUSTOM SETTING] key.
500
Default Set range 0 ~ 375 0 ~1250
SIMULATION 8-6 THV+SETTING. EXECUTING... 1. FRONT
140
1 SHV front surface SHV back surface THV-output 2 Default Set range 0 ~ 620 Main code 21 3 780
1 Cassette/manual paper feed 2 Paper feed from ADU 45PPM 45PPM 267 310
160(45PPM) 120(28/35PPM)
28/35PPM 220 28/35PPM 267
21-1
Purpose Function (Content) Section Item Operation/Procedure Setup Used to set the maintenance cycle. Spec Used to set the maintenance cycle in an SRU machine.
SIMULATION 21-1 MAINTENANCE CYCLE SETUP. SELECT 0-6, AND PRESS START. 0. DEFAULT 1. 5K 2. 10K 3. 25K 4. 50K 5. 80K 6.FREE 7. 100K 8. 20K 9. 40K
1
0 1 2 3 4 5 6 7 8 9 Maintenance display at the cycle of each control spec. Maintenance display at 5K Maintenance display at 10K Maintenance display at 25K Maintenance display at 50K Maintenance display at 80K No maintenance display Maintenance display at 100K Maintenance display at 20K Maintenance display at 40K
AR-M280U SIMULATIONS 9-1
Main code 44
44-1
Purpose Function (Content) Setup Used to set Enable/Disable of each correction operation in the image forming (process) section. Process (OPC drum, developing, transfer, cleaning) Operation
Section Item Operation/Procedure
*1: Only when this value is 0, control is performed with the actual measurement value of process Thermistor. If it is not 0, control is forcibly performed. *2: When the drum motor standby time is greater than this value, the correction of SIM 44-1 Vb1 is performed. *3: This value is SIM 44-9 Vb1-1 correction value. The value corresponding to the drum rotating time is used. *4: This value is SIM 44-9 Vb1-2 correction value. The value corresponding to the drum rotating time is used. DRUM ROTATION TIME 45PPM 0 ~ 40K (sec) 40 ~ 80K (sec) 80K ~ (sec) 35PPM 28PPM 0 ~ 50K (sec) 50 ~ 95K (sec) 95K ~ (sec) Vb1 correction value (X' th rotation) (X' th rotation) -1 (X' th rotation) -2 (X' th rotation) -3
SIMULATION 44-1 PROCESS CORRECTION VALUE SETTING. INPUT VALUE 0-255 AND PRESS START. BIT0:Vg1, BIT1:Vg2, BIT2:Vb1, BIT3:Vb2 BIT4:Vb3, BIT5:LD1, BIT6:LD2 BIT7:EX
255
44-9
Adjustment, setup, operation data output, check (display) Function (Content) Used to check the result (main charger grid voltage developing bias voltage, laser power, etc.) of correction (process correction) in the image forming section. (By this simulation, the correction operation can be checked.) Section Process (OPC drum, developing, transfer, cleaning) Item Data Operation/Procedure The process correction value is checked.
SIMULATION 44-9 PROCESS CONTROL DATA DISPLAY. DRUM ROTATION TIME: 01234567 (sec) Vg1: 30 (V) Vg2: 30 (V) Vb1-1: 30 (V) Vb1-2: 30 (V) Vb2: 10 (V) LD1: 0.05 (mW) LD2: 0.05 (mW) CONTROL: 1 DESTINATION: A TO: -5 T1: -5 T2: -3
Purpose
bit = 1 : Correction enabled Bit 15 14 13 12 11 10 9 0 0 0 0 0 0 0
8
0
7
6
5
4
3
2
1
0
EX LD2 LD1 Vb3 Vb2 Vb1 Vg2 Vg1
44-4
Purpose Function (Content) Setup Used to set the target image (reference) density level in the developing bias voltage correction. Section Process (OPC drum, developing, transfer, cleaning) Item Data Operation/Procedure The process correction value is set. Select an item (1 - 9), and enter a value with 10 digit key pad. Press START to store the value.
SIMULATION 44-4 PROCESS CONTROL VALUE SETTING. SELECT 1-8 AND PRESS START. 1.PTH 00 2.S-WT 100 3.Vb1-1 50 4.Vb1-2 50 5.Vb1-3 50 6.Vb2-1 50 7.Vb2-2 50 8.Vb2-3 50
PTH: 30 (deg)
1
Press [START] key.
Press [CUSTOM SETTING] key.
SIMULATION 44-4 PROCESS CONTROL VALUE SETTING. INPUT VALUE, AND PRESS START. 1.PTH
45
1 PTH *1 2 S_WT *2 3 Vb1-1 *3 4 Vb1-2 *3 5 Vb1-3 *3 6 Vb2-1 *4 7 Vb2-2 *4 8 Vb2-3 *4 Process Thermistor temperature forcible set value (0-99°C : Normal 0) Vb (Developing bias correction value) rising correction wait time (0-180sec : Default 90) Vb (Developing bias correction value) correction quantity (First rotation) 1 (0 - 150V : Default 50) Vb (Developing bias correction value) correction quantity (First rotation) 2 (0 - 150V : Default 50) Vb (Developing bias correction value) correction quantity (First rotation) 3 (0 - 150V : Default 50) Vb (Developing bias correction value) correction quantity (Second rotation) 1 (0 - 50V : Default 15) Vb (Developing bias correction value) correction quantity (Second rotation) 2 (0 - 50V : Default 15) Vb (Developing bias correction value) correction quantity (Second rotation) 3 (0 - 50V : Default 15)
DRUM ROTATION TIME Drum rotation time Vg1~Vg2 Grid voltage correction value Vb1-1 *1 Vb (Developing bias correction value) correction value (first rotation) Vb1-2 *1 Vb (Developing bias correction value) correction value (second rotation) Vb2 Developing bias correction value Vb3 Developing bias correction value LD1 Laser power correction value LD2 Laser power correction value CONTROL CRUM control spec (1 - 3) DESTINATION CRUM destination (A - L) PTH *2 Process Thermistor temperature value T0 Toner control correction value (Rotation time correction) (±100) T1 Toner control correction value T1 (Temperature correction) (±100) T2 Toner control correction value T2 (Temperature correction) (±100) *1: Vb1-1 and Vb1-2 are enabled or disabled by SIM 44-1 Vb1 setup. *2: When PTH is set to 0 with SIM 44-4, the detected value in this adjustment is displayed. If PTH is set to other than 0, the value set with SIM 44-4 is displayed.
AR-M280U SIMULATIONS 9-2
Main code 51 45PPM 28PPM 35PPM 0 TRAY SELECT 1 PRINT START 2 TRAY1 3 TRAY2 4 DESK 5 BPT 6 ADU Paper feed tray selection (1 - 5) Copy start (Initial value) Tray 1 resist adjustment value Tray 2 resist adjustment value Desk resist adjustment value Manual tray resist adjustment value ADU resist adjustment value 60 50 50 55 50 60 75 65 55 55 60 55 60 75
51-2
Purpose Function (Content) Adjustment Used to adjust the contact pressure of paper on the resist roller in each section (machine paper feed, duplex paper feed, SPF paper feed). (This adjustment is required when the print image position varies or when paper jam occurs frequently.) Section Paper transport (paper exit, switchback, transport) Item Operation Operation/Procedure Perform the resist quantity adjustment. 1) The current set value is highlighted on the right of each item. In this screen, be sure to select "1: COPY START." (Set value: 1) 2) Enter the correction value with 10 digit key pad. Press P to store the set value. 3) When the value is increased by 1, the resist quantity is changed by 1ms. 4) Press START to start copying and store the set value. (Display value: 1) 5) Select a paper feed tray. (Set value 2)
7 SPF(HIGH) SPF resist adjustment value (High speed) 8 SPF(LOW) SPF resist adjustment value (Low speed) Normal display ERROR display Door open Jam Paper empty
NOW COPYING DOOR OPEN. JAM PAPER EMPTY.
1 2 3 4 5 * TRAY1 TRAY2 TRAY3 TRAY4 Manual feed 11 12 13 14 15 TRAY1 with Duplex TRAY2 with Duplex TRAY3 with Duplex TRAY4 with Duplex Manual feed with Duplex
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. SELECT 0-8, AND PRESS START. 0. TRAY SELECT 1 1.PRINT START 2. TRAY1 50 3. TRAY2 50 4. DESK 50 5. BPT 50 6. ADU 50 7. SPF(HIGH) 50 8. SPF(LOW) 50 Select 0 or 1, and press [START] key.
1
The selected tray is registered as an initial set value in the initial screen. Main code 61
Press [CUSTOM SETTING] key.
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. INPUT VALUE 0-99, AND PRESS START. 1. TRAY1
61-2
Purpose Function (Content) Adjustment Used to adjust the laser power (absolute value) in the copy mode. Section PCU Item Operation Operation/Procedure Enter the laser power set value in copying, and press START to store it.
SIMULATION 61-2 LASER POWER SETTING (COPY). SELECT 1-4, AND PRESS START. 1. AE 5 2. TEXT 5 3. MIX 5 4. PHOTO 5
Select 1, and press [START] key.
Press [CUSTOM SETTING] key. Or copying is terminated.
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. NOW PRINTING.
Select 0, and press [START] key.
Press [START] key or press [CUSTOM SETTING] key.
1
SIMULATION 51-2 RESIST TIMING ADJUSTMENT. SELECT 1-15, AND PRESS START. (FEED TRAY) 1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4 5. BPT (ABOVE +10: DUPLEX MODE)
Press [START] key.
Press [CUSTOM SETTING] key or [START] key.
SIMULATION 61-2 LASER POWER SETTING(COPY). INPUT VALUE 1-165, AND PRESS START. 1. AE
5
Initial value 1 2 3 4 Auto exposure mode Text mode Text/Photo mode Photo mode 45PPM 35/28PPM 45PPM 35/28PPM 45PPM 35/28PPM 45PPM 35/28PPM 100 76 100 76 100 76 100 76 Set range 100 - 150 (45PPM) 76 - 150 (28/35PPM)
AR-M280U SIMULATIONS 9-3
61-3
Purpose Function (Content) Adjustment Used to adjust the scanner (exposure) laser power (absolute value) in the FAX reception mode. (Only when FAX is installed.) Section PCU Item Operation Operation/Procedure Set the laser power in FAX reception. Enter the set value and press Start to store it.
SIMULATION 61-3 LASER POWER SETTING (FAX). PRESS START. 1. FAX 5
Default setup for supporting 100K drums
1) When the value is changed from 127 to 255 by SIM 44-1, the following default values of the laser power setup must be adjusted. Drum Sim44-1 Model Laser power setup SIM 61-2 Maintenance cycle SIM 21-1 80 50K 127 35PPM 45PPM 104 35PPM 76 100K(80K) 255 45PPM 100 28PPM 76
0(50K)
7(100K)
5(80K)
1
*
Press [START] key.
Press [CUSTOM SETTING] key or [START] key.
SIMULATION 61-3 LASER POWER SETTING (FAX). INPUT VALUE 1-165, AND PRESS START. 1. FAX
When the EEPROM is replaced (memory is cleared) in a 28-sheet machine, setup of the 100K drum must be performed with SIM 44-1 (setup value: 255). The above setup values are adjusted according to the setup of SIM 44-1. (Though the destination setup is changed (SIM 26-6), the above setup will not be changed automatically.)
5
Initial value 1 FAX reception 45PPM 35/28PPM 100 76 Set range 100 - 150 (45PPM) 76 - 150 (28/35PPM)
61-4
Purpose Function (Content) Adjustment Used to adjust the laser power (absolute value) in the printer mode. PCU
Section Item Operation/Procedure Set the laser power value in the printer mode. Enter the value and press START to store it.
SIMULATION 61-4 LASER POWER SETTING (PRINTER). PRESS START. 1. PRINTER 5
1
Press [START] key.
Press [CUSTOM SETTING] key or [START] key.
SIMULATION 61-4 LASER POWER SETTING (PRINTER). INPUT VALUE 1-165, AND PRESS START. 1. PRINTER
5
Initial value 1 PRINTER 45PPM 28/35PPM 100 76 Set range 100 - 150 (45PPM) 76 - 150 (28/35PPM)
AR-M280U SIMULATIONS 9-4
q
PARTS GUIDE
LASER PRINTER (MULTI FUNCTION)
AR-M280N MODEL AR-M280U
CONTENTS
1 2 3 4 7 8 9 F G H J K L M N P V W
s
Exteriors Left door unit PS roller unit TC unit Fusing unit Delivery turn over unit MC unit Process unit Developer unit Controller BOX unit Rear frame section 1 Rear frame section 2 Cassetter unit Packing material & Accessories PCU PWB unit Mother board MFP Control PWB (ARM280N) STD control PWB (ARM280U) index
The AR-M280N/M280U Parts Guide describes only the parts change from AR-P350/AR-P450 Parts Guide. for the common parts, please refer to the AR-P350/AR-P450(CODE :00ZAR350LPP1/) Parts Guide.
DEFINITION
The definition of each Rank is as follows and also noted in the list A: Parts necessary to be stocked as High usage parts. B: Parts necessary to be stocked as Standard usage parts. C: Low usage parts. D: Parts necessary for refurbish. E: Unit parts recommended to be stocked for efficient after sales service. Please note that the lead time for the said parts may be longer than normal parts. S: Consumable parts. Please note that the following parts used in Copier under the same description are classified into A or B Rank depending upon the place used. Example : Gear made of Metal, Sprocket, Bearing, Belt made of Rubber, Spring clutch mechanism. ARank : The parts which may be with the revolution or loading. BRank : Parts similar to A Rank parts, but are not included in Rank A. Because parts marked with "!" is indispensable for the machine safety maintenance and operation, it must be replaced with the parts specific to the product specification. F Other than this Parts Guide, please refer to documents Service Manual(including Circuit Diagram)of this model. F Please use the 13 digit code described in the right hand corner of front cover of the document, when you place an order. F For U.S. only-Use order codes provided in advertising literature. Do not order from parts department.
1 Exteriors
NO.
5 11 26
PARTS CODE
GCAB-0940FCZ2 HPNLC0243FCZ1 CPNLH0020QS41 CPNLH0020QS42
PRICE NEW RANK MARK BA AP AK N AK N
PART RANK D D D D
DESCRIPTION
Paper exit tray exterior Operation cabinet Model panel Model panel [ARM280U] [ARM280N]
2 Left door unit
NO.
3 9 13 16 27
PARTS CODE
LX-BZ0147FCZ1 PTME-0287FCZ1 LANGT1407FCZ2 PTME-0279FCZ1 NFANP0069FCZZ
PRICE NEW RANK MARK AC AD AR AB AV
PART RANK C C C C B
DESCRIPTION
Screw Transfer lock pawl ACC fixing angle F Left door lock pawl Fan
3 PS roller unit
NO.
11 38
PARTS CODE
PSHEP4925FCZZ LX-BZ0589FCZZ
PRICE NEW RANK MARK AC AA
PART RANK C Paper powder remove sub sheet C Screw
DESCRIPTION
4 Main drive unit
NO.
25 67 71
PARTS CODE
LX-BZ0670FCZ1 LX-BZ0788FCZ1 NSFTZ2576FCZ1
PRICE NEW RANK MARK AC AC AL
PART RANK C Screw C Screw C PS roller shaft
DESCRIPTION
7 Fusing unit
NO.
3 11
PARTS CODE
PTME-0282FCZ1 PCOVP1546FCZ1
PRICE NEW RANK MARK AH AY
PART RANK C Upper separator pawl C Fusing upper cover
DESCRIPTION
1
8 Delivery turn over unit
NO.
5 10 14 38 47 62 66
PARTS CODE
NFANP0069FCZZ PGIDM1896FCZ1 LDAIU0626FCZ2 NBLTH0327FCZ1 NBLTH0350FCZ1 PBRSS0208FCZ1 PSHEP4962FCZ1
PRICE NEW RANK MARK AV AV AK AL AH AH AC
PART RANK B C C C C C C
DESCRIPTION
Fan Paper exit upper PG Paper exit follower roller fixing plate Belt Belt Discharge brush Belt holder sheet
8 Delivery turn over unit
66
9 MC unit
NO.
3
FCP05237
PRICE NEW RANK MARK AL PART RANK E Plate
PARTS CODE
CPLTM6048DS51
DESCRIPTION
F Process unit
NO.
8 16 24 26 45 47 48 57 59 60 501
PARTS CODE
PMLT-1245FCZ2 MSPRC3010FCZ1 XBBSD30P08000 LX-BZ0656FCZ1 PRNGF0106FCZ2 MSPRC2954FCZ2 PMLT-1238FCZ1 LX-WZ0440FCZZ PSPAZ1431FCZZ PSPAZ1432FCZZ CHLDZ1473DS51
PRICE NEW RANK MARK AE AB AA AE AC AB AC AC AA AA BH
PART RANK C C C C C C C C C C E
DESCRIPTION
Process U cushion Shutter open close spring Screw(3×8) Screw Starling N Sparation pawl spring Toner shield cushion Spacer Spacer A Spacer B Separation pawl holder unit
F Process unit
60
57
59
FCP05238
2
G Developer unit
NO.
29 48 49 56
PARTS CODE
LPLTM6022FCZZ PMLT-1241FCZ1 PMLT-1244FCZ1 PMLT-1296FCZZ
PRICE NEW RANK MARK AC AA AC AH
PART RANK C C C C
DESCRIPTION
M4 plate DV-BOX cushion Docter cushion R Shutter cushion
G Developer unit
56
H Controller BOX unit
NO.
1 5 9 12 14 21 25 26 35 37 38 45 47 50 51 54 55 56 57
FCP05239
PRICE NEW RANK MARK AF AV AE AV AG CD N AE AA AH AC AC AC AA AA AA BR BU BR BU AD AC PART RANK C B C B C E C C C C C C C C C B B B B C C
PARTS CODE
PDUC-0165FCZ1 NFANP0069FCZZ PCOVP1555FCZ1 NFANP0069FCZZ QCNW-0201FCZZ DUNT-7093DS15 LX-BZ0921FCZ1 XBPSD26P06000 LPLTM5765FCZ1 PCOVP1560FCZZ PCOVP1557FCZZ PSHEP4945FCZZ XBPSD30P06000 XHBSE30P06000 XBBSD30P06000 VHI28F322L03F VHI28F322L15F VHI28F322L04F VHI28F322L16F LX-BZ0828FCZZ PSHEP5009FCZZ
DESCRIPTION
Controller duct Fan Controller BOX cover Fan Printer interface FFC LSU 28 unit Screw(3×6) Screw(2.6×6) Control joint plate FAX I/F cover LAN/Option cover Controller duct sheet B Screw(3×6) Screw(3×6) Screw(3×6) MFP flash ROM A(28F322L03F) STD flash ROM A(28F322L15F) MFP flash ROM B(28F322L04F) STD flash ROM B(28F322L16F) Screw Control duct sheet
H Controller BOX unit
45 57 38 37 51 51 47 50 26 25 51 51 51 26 56 35 51 51 51 51 47 50 47 56 55 54 45 21 38
FCP05240
3
J Rear frame section 1
NO.
1 4 5 7 37 55 56
PARTS CODE
NFANP0069FCZZ XHBSE40P08000 PSHEZ4874FCZ1 PSHEZ4873FCZ1 PSHEZ4885FCZ1 PCOVP1693FCZZ LSTYM0255FCZ1
PRICE NEW RANK MARK AV AA AC AC AB AH AL
PART RANK B C C C C C C
DESCRIPTION
Fan Screw(4×8) LSU cleaning sheet R LSU cleaning sheet F Paper feed base sheet R Duct support cover Duct support plate
J Rear frame section 1
5
4 7
4 55
56
K Rear frame section 2
NO.
6 26 54 55 56 58
FCP05241
PART RANK B E C C C B
PARTS CODE
RPLU-0326FCZ2 CPWBN1515FCE2 QCNW-0205FCZZ QCNW-0204FCZZ QCNW-0203FCZZ VHI28F081L06F
PRICE NEW RANK MARK AN BY N AC AC AD BE
DESCRIPTION
Separator pawl solenoid PCU PWB unit HV interface FFC Drum motor interface FFC Main motor interface FFC PCU flash ROM(28F081L06F)
L Cassette unit
NO.
20 25
PARTS CODE
PTPE-0243FCZ1 PGIDH1833FCZ1
PRICE NEW RANK MARK AC AC N
PART RANK C Side plate tape C Side plate guide
DESCRIPTION
M Packing material & Accessories
NO.
5 6 12 13
PARTS CODE
SPAKC6122DS46 SPAKC6122DS45 TCADZ1521FCZ1 CDSKA0005FC39 PSHEP4927FCZZ TINSE2288FCZZ TINSF2289FCZZ TINSF2291FCZZ TINSF2293FCZZ TINSF2296FCZZ TINSE2290FCZZ TINSE2292FCZZ TINSE2294FCZZ TINSE2295FCZZ TINSE2297FCZZ SPAKA6272FCZZ
20
28
PRICE NEW RANK MARK N N AE AM AM AZ N N N AN N AU N AN AK N AK N AN AG
PART RANK D D D D D D D D D D D D D D D D
DESCRIPTION
Packing case Packing case Fusing pressurization manual Printer CD Key sheet MFP Operation manual PRT Operation manual PRT Operation manual Operation manual Operation manual Operation manual Operation manual SCANNER Operation manual KEY Operation manual Operation manual Fusing protect add R [ARM280N] [ARM280U]
[USA] [French] [French] [French] [French] [USA] [USA] [USA] [USA] [USA]
M Packing material & Accessories
28
FCP05242
4
N PCU PWB unit
NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
PARTS CODE
QCNCM0670FCZZ QCNCM0878FCZZ QCNCM0923FC24 QCNCM0923FC32 QCNCM1069ACZZ QCNCM1143FCZZ QCNCM1144FCZZ QCNCM1175FCZZ QCNCM5093SC0B QCNCM7014SC0H QCNCM7014SC1A QCNCM7014SC1D QCNCW0002ESZZ QCNCW1136FCZZ QCNCW1139FCZZ QCNCW1140FCZZ QCNCW1150FCZZ QSOCZ0002QSZZ QSOCZ0071FCZZ QSW-P0005QSZZ RCRSZ0001QSZZ RCRUB0002FCZZ RFILN0042FCZZ RFILN0047FCZZ RMPTR4103ACZZ VCCCCZ1HH100D VCCCCZ1HH101J VCCCCZ1HH220J VCEAGA0JW107M VCEAGU1AW476M VCEAGA1AW477M VCEAGA1CW477M VCEAGU1HW335M VCEAGA1VW106M VCEAGU1VW107M VCEAGA1VW227M VCEAGU1VW476M VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1CF104Z VCKYCZ1EF223Z VCKYCZ1EF223Z VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB102K VCKYCZ1HB222K VCQYNU1HM103K VHDDAN202K/-1 VHDDAN202K/-1 VHDDAP202K/-1 VHDDA204K//-1 VHDDSS133//-1 VHDMA704A//-1 VHDM1FL20U+-1 VHEHZS3B3//-1 VHERD22FB//-1 VHID82805GN-1 VHIEES04L400P VHIFS781BZB-1 VHIFS781BZB-1 VHIH8S2322R-1 VHILM324D++-1 VHILM339D++-1 VHILVX240SJ-1 VHIMTD13611-1 VHINJM7805A-1 VHITA7291S/-1 VHITD62003AP1 VHITD62503F/VHI74VHCT240X VHI74VHCT244X
38
39
40
41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
PRICE NEW RANK MARK AC AF AF AG AD AG AH AG AB AB AC AC AC AC AC AD AE AD AP AC AG AP AC AC AB AA AA AA AC AA AB AB AA AA AB AB AB AB AB AB AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AB AC AA AC AC AB AD BA AG AP AP AZ AE AE AG AR AH AF AG AG AF AF
PART RANK C C C C C C C C C C C C C C C C C C C B B B C C B C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C B B B B B B B B B B B B B B B B B B B B B B B B
DESCRIPTION
Connector(5pin) Connector(30pin) Connector(24pin) Connector(32Pin) Connector(6pin) Connector(22pin) Connector(24pin) Connector(30pin) Connector(2pin) Connector(8pin) Connector(11pin) Connector(14pin) Connector(8pin) Connector(8pin) Connector(14pin) Connector(28pin) Connector(24pin) IC socket(8pin) Socket(MM20-72B1-1) Tact switch(B3F-6102) Crystal(19.6608MHz) Crystal(31.554MHz) EMI filter(ZJSR5101-101) EMI filter(MMZ1608S121) Block resistor(10K×4) Capacitor(50WV 10pF) Capacitor(50WV 100pF) Capacitor(50WV 22pF) Capacitor(6.3WV 100µF) Capacitor(10WV 47µF) Capacitor(10WV 470µF) Capacitor(16WV 470µF) Capacitor(50WV 3.3µF) Capacitor(35WV 10µF) Capacitor(35WV 100µF) Capacitor(35WV 220µF) Capacitor(35WV 47µF) Capacitor(16WV 0.10µF) Capacitor(16WV 0.10µF) Capacitor(16WV 0.10µF) Capacitor(16WV 0.10µF) Capacitor(16WV 0.10µF) Capacitor(16WV 0.10µF) Capacitor(50WV 0.022µF) Capacitor(50WV 0.022µF) Capacitor(50WV 1000pF) Capacitor(50WV 1000pF) Capacitor(50WV 1000pF) Capacitor(50WV 1000pF) Capacitor(50WV 1000pF) Capacitor(50WV 1000pF) Capacitor(50WV 1000pF) Capacitor(50WV 1000pF) Capacitor(50WV 1000pF) Capacitor(50WV 2200pF) Capacitor(50WV 0.010µF) Diode(DAN202K) Diode(DAN202K) Diode(DAP202K) Diode(DA204K) Diode(1SS133) Diode(MA704A) Diode(M1FL20U) Zener diode(HZS3B3) Zener diode(RD22FB)(20.8-23.3V) IC(D82805GN) IC(EES04L400P) IC(FS781BZB) IC(FS781BZB) IC(H8S2322R) IC(LM324D) IC(LM339D) IC(LVX240SJ) IC(MTD1361-4101) IC(NJM7805A) IC(TA7291S) IC(TD620003AP1) IC(TD62503F) IC(74VHCT240X) IC(74VHCT244X) [CN17] [CN12] [CN13] [CN4] [CN18] [CN11] [CN10] [CN16] [CN7,22] [CN5] [CN8] [CN14] [CN9] [CN6] [CN15] [CN1,2] [CN3] [IC17] [SOCKET1] [SW1] [X1] [X2] [NF111] [NF12,13] [BR1BR24] [C86] [C12,13,28,43] [C39,50] [C146] [C17] [C99] [C108,147] [C63] [C2,104] [C117,118] [C129] [C9,144] [C6,19,29,30,32,40,42,47] [C51,55,58,59,61,75,80] [C87,88,101,102,106,116] [C120,121,131,132,138] [C140,142,143,151,153] [C189,190,191] [C14,62,100,107,123] [C124,128,130,145] [C1,5,15,16,18,31,33,34] [C36,37,41,44,46,48,49,52] [C53,54,57,60,6474] [C76,77,78,81,8285] [C89,90,91,93,94,96,97,98] [C103,105,109115,119] [C125,126,127,133,136,137] [C139,141,149,155,156,160] [C173188,148,154] [C3,7,8,11] [C150] [D1,8,9,11,13,16] [D18,23,29,32] [D10,14,15,17,30] [D2,3,12,19,20,31] [D25,26,27] [D22,28] [D4,5,6,7,33] [ZD1] [ZD2,3] [IC16] [IC17] [IC13] [IC13] [IC8] [IC22] [IC18,21] [IC6] [IC3] [IC25] [IC2,15] [IC1,19,20] [IC7,12,14,23,24,26] [IC9] [IC4,5,10]
5
N PCU PWB unit
NO.
65 66 67 68 69 70 71 72 73
PARTS CODE
VHP1LHEE-002A VHVICPS1.2/-1 VRD-HT2EY911J VRD-HT2HY242J VRD-HT2HY471J VRS-CZ1JD000J VRS-CZ1JD000J VRS-CZ1JD101J VRS-CZ1JD102J VRS-CZ1JD102J VRS-CZ1JD103F VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD103J VRS-CZ1JD104J VRS-CZ1JD122J VRS-CZ1JD151J VRS-CZ1JD152F VRS-CZ1JD152J VRS-CZ1JD153F VRS-CZ1JD201J VRS-CZ1JD203J VRS-CZ1JD203J VRS-CZ1JD203J VRS-CZ1JD304F VRS-CZ1JD330J VRS-CZ1JD330J VRS-CZ1JD330J VRS-CZ1JD330J VRS-CZ1JD332J VRS-CZ1JD471J VRS-CZ1JD472F VRS-CZ1JD473F VRS-CZ1JD473J VRS-CZ1JD562J VRS-CZ1JD621F VRS-CZ1JD680J VRS-CZ1JD681F VRS-CZ1JD681J VRS-CZ1JD752J VRS-CZ1JD822F VRS-RE3AA241J VRS-RE3DA1R0J VRS-RE3DA8R2J VSDTA123YK/-1 VSDTC114YK/-1 VSDTD114EK/-1 VS2SK3018++-1 (Unit) CPWBN1515FCE2
74
75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 901
PRICE NEW RANK MARK AC AF AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AB AC AB AC AC AC BY N
PART RANK B B C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C B B B B E
DESCRIPTION
LED (Red)(1LHEE-002A) IC protecrot(ICPS1.2) Resistor(1/4W 910 ±5%) Resistor(1/2W 2.4K ±5%) Resistor(1/2W 470 ±5%) Resistor(1/16W 0 ±5%) Resistor(1/16W 0 ±5%) Resistor(1/16W 100 ±5%) Resistor(1/16W 1.0K ±5%) Resistor(1/16W 1.0K ±5%) Resistor(1/16W 10K ±1%) Resistor(1/16W 10K ±5%) Resistor(1/16W 10K ±5%) Resistor(1/16W 10K ±5%) Resistor(1/16W 10K ±5%) Resistor(1/16W 10K ±5%) Resistor(1/16W 10K ±5%) Resistor(1/16W 10K ±5%) Resistor(1/16W 10K ±5%) Resistor(1/16W 10K ±5%) Resistor(1/16W 100K ±5%) Resistor(1/16W 1.2K ±5%) Resistor(1/16W 150 ±5%) Resistor(1/16W 1.5K ±1%) Resistor(1/16W 1.5K ±5%) Resistor(1/16W 15K ±1%) Resistor(1/16W 200 ±5%) Resistor(1/16W 300K ±5%) Resistor(1/16W 300K ±5%) Resistor(1/16W 300K ±5%) Resistor(1/16W 20K ±5%) Resistor(1/16W 33 ±5%) Resistor(1/16W 33 ±5%) Resistor(1/16W 33 ±5%) Resistor(1/16W 33 ±5%) Resistor(1/16W 3.3K ±5%) Resistor(1/16W 470 ±5%) Resistor(1/16W 4.7k ±1%) Resistor(1/16W 47k ±1%) Resistor(1/16W 47K ±5%) Resistor(1/16W 5.6K ±5%) Resistor(1/16W 620 ±1%) Resistor(1/16W 68 ±5%) Resistor(1/16W 680 ±1%) Resistor(1/16W 680 ±5%) Resistor(1/16W 7.5K ±5%) Resistor(1/16W 8.2K ±1%) Resistor(1W 240 ±5%) Resistor(2W 1.0 ±5%) Resistor(1W 8.2 ±5%) Transistor(DTA123YK) Transistor(DTC114YK) Transistor(DTD114EK) Transistor(2SK3018) PCU PWB unit [LED1] [ICP1] [R141] [R5,6] [R172,173] [R1,39,110,170,171,199] [R200,201,203,204,207] [R59,125,178,197,198] [R13,15,36,44,51] [R140,205,206] [R2,132,154,157,182] [R4,12,22,23,2733] [R35,38,43,5255,72] [R73,74,77,80,83,84,92] [R93,94,104,106,108] [R109,111,112,113,115] [R117120,123,126] [R127,129,133,135,136] [R144,153,161,164,165] [R179,183,188,292,294] [R138] [R151] [R17,24] [R142,150] [R16] [R152,181] [R25,26,139] [R11,114,145,166,174] [R175,176,177,191,192] [R193,194,195,196] [R146,159] [R40,41,4550,56,57] [R58,6063,65,66,68] [R69,70,71,75,76,78,79] [R8591,95103] [R81] [R18,19] [R131,143,149,163] [R148,162] [R186,187,189,190] [R137,169] [R147,158] [R105] [R156,185] [R42] [R3,21] [R155,184] [R160] [R14,20] [R167] [Q8,9] [Q2,4,5,6,7] [Q1] [Q10,11]
P Mother board
NO.
9
PARTS CODE
VRS-RE3LA6R2J
PRICE NEW RANK MARK AC
PART RANK C Resistor(3W 6.2 ±5%)
DESCRIPTION
V MFP Control PWB (ARM280N)
NO.
1 2 3 4 5 6 7
PARTS CODE
PCAPH0010GCZZ PCOVP1468FCZZ QCNCM1183FCZZ QCNCM1146FCZZ QCNCM1182FCZZ QCNCW0946FCZZ QCNCW1147FCZZ
PRICE NEW RANK MARK AD AD AM AE AM AH AL
PART RANK C C C C C C C
DESCRIPTION
Jumper cap(JM-2W-96) Battery cover Connector(100P15.2JXK) Connector(9A12-1034) Connector(100P9.2JXKS) Connector(36pin) Connector(TX2450RLTH1) [JP2,3,4,5,6,7] [CN2,12] [CN14] [CN16] [CN1] [CN13]
6
V MFP Control PWB (ARM280N)
NO.
! 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
PARTS CODE
QCNCW1149FCZZ QFS-D132CQCZZ QFSHB0028FCZZ QPIN-0003GCZZ QSOCZ0001QSZZ QSOCZ0073FCNA QSOCZ6428ACZZ RCRSP6676RCZZ RCRUA0005FCZZ RCRUA0007FCZZ RCRUA0008FCZZ RCRUA0009FCZZ RCRUA0012FCZZ RCRUA0014FCZZ RFILN0048FCZZ RFILN0051FCZZ RMPTR4100ACZZ RMPTR4100ACZZ RMPTR4103ACZZ RMPTR4103ACZZ RMPTR4330ACZZ RMPTR4472ACZZ UBAT