Text preview for : 09-001-335-3N6.pdf part of AIWA AZG-1 Service manual CD-R/RW mechanism
Back to : 09-001-335-3N6.pdf | Home
AZG-1
English
SERVICE MANUAL
CD-R/RW MECHANISM BASIC CD MECHANISM:KSM-880CAB TYPE ZD8RD YZD8RMDJM ZD8RMDJM ZD8RDNDM YKZD8RDF ZD8RDM YZD8RDM ZD8RN1DM YZD8RDJM
S/M Code No. 09-001-335-3N6
DA TA
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
Precaution to replace Optical block
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the figure below.
Solder
2
How to Adjust the Rotating Phase of the Gear, Main Cam
1) Push down the hooking catch of the CHAS. MECH, and remove the TRAY. 2) Align the arrow mark of the Gear, Main Cam with the black round mark of the CHAS, MECHA as shown below. 3) Confirm that the Slide, Mech Cam is located in the right position, then insert the TRAY gently. Caution: If the rotating phase of the Gear, Main Cam is incorrectly adjusted, the chucking operation and tray movement will have malfunction.
Align the arrow 2 mark with the black round · mark.
3
ELECTRICAL MAIN PARTS LIST
REF. NO IC
PART NO.
KANRI NO.
DESCRIPTION
REF. NO C109 C110
87-A21-381-040 87-A21-556-010 87-A21-414-010 TRANSISTOR 87-026-609-080 87-A30-076-080 87-A30-497-080 87-A30-087-080 87-026-237-080 87-A30-075-080 DIODE
C-IC,LA9235M C-IC,LC78641E IC,BA5927S
C110 C111 C112
KANRI DESCRIPTION NO. 87-010-992-080 C-CAP,S 0.047-25 B 87-010-196-080 CHIP CAPACITOR,0.1-25 87-010-196-020 CHIP CAPACITOR,0.1-25 87-010-260-080 CAP, ELECT 47-25V 87-010-197-020 CHIP CAPACITOR,0.01-25 87-010-197-080 87-010-260-080 87-010-197-080 87-010-197-020 87-010-260-080 87-010-197-080 87-010-197-020 87-010-260-080 87-015-819-080 87-010-312-080 87-010-312-020 87-010-312-020 87-010-312-080 87-010-404-080 87-010-197-020 87-010-197-080 87-010-401-080 87-010-196-020 87-010-196-080 87-010-196-020 87-010-196-080 87-010-196-080 87-010-196-020 87-010-405-080 87-010-314-020 87-010-314-080 87-A11-088-080 87-010-405-080 87-010-405-080 87-012-349-080 87-010-196-080 87-010-196-020 87-A10-730-080 87-010-196-080 87-010-196-020 87-010-196-020 87-010-196-080 87-010-405-080 87-010-405-080 87-010-196-020 CHIP CAPACITOR,0.01-25 CAP, ELECT 47-25V CHIP CAPACITOR,0.01-25 CHIP CAPACITOR,0.01-25 CAP, ELECT 47-25V CHIP CAPACITOR,0.01-25 CHIP CAPACITOR,0.01-25 CAP, ELECT 47-25V C-CAP,S 15P-50 CH C-CAP,S 15P-50 CH C-CAP,S 15P-50 CH C-CAP,S 15P-50 CH CAP, ELECT 4.7-50V CHIP CAPACITOR,0.01-25 CHIP CAPACITOR,0.01-25 CAP, ELECT 1-50V CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP, ELECT 10-50V C-CAP,S 22P-50V C-CAP,S 22P-50V CAP,TC U 100P-50 J CH CAP, ELECT 10-50V CAP, ELECT 10-50V C-CAP,S 1000P-50 CH CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP,E 1000-16 SMG CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP, ELECT 10-50V CAP, ELECT 10-50V CHIP CAPACITOR,0.1-25
PART NO.
TR,KTA1266GR C-TR,2SC3052F TR,2SA1980Y/G C-FET,2SK2158 CHIP-TR,DTC124XK C-TR,2SA1235F
C112 C114 C115 C115 C116 C117 C117
87-A40-270-080 87-070-136-080 87-A40-003-080 87-A40-337-080 87-A40-313-080 3CD C.B
C-DIODE,MC2838 ZENER,MTZJ5.1B ZENER,MTZJ4.3A ZENER,MTZJ6.8B C-DIODE,MC2840
C118 C119 C120 C120 C121
C1 C2 C2 C3 C4 C5 C5 C6 C7 C8 C10 C11 C13 C13 C15 C15 C16 C101 C102 C103 C103 C104 C104 C105 C106 C106 C107 C107 C108 C108
87-010-374-080 87-010-196-020 87-010-196-080 87-010-260-080 87-010-260-080 87-010-197-020 87-010-197-080 87-010-405-080 87-010-263-080 87-012-349-080 87-010-546-080 87-010-401-080 87-010-321-020 87-010-321-080 87-010-197-020 87-010-197-080 87-010-260-080 87-010-992-080 87-010-401-080 87-010-196-020 87-010-196-080 87-010-196-020 87-010-196-080 87-010-260-080 87-010-322-020 87-010-322-080 87-010-196-020 87-010-196-080 87-010-186-080 87-010-186-020
CAP,E 47-10 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP, ELECT 47-25V CAP, ELECT 47-25V CHIP CAPACITOR,0.01-25 CHIP CAPACITOR,0.01-25 CAP, ELECT 10-50V CAP, ELECT 100-10V C-CAP,S 1000P-50 CH CAP,E 0.33-50 CAP, ELECT 1-50V C-CAP,S 82P-50 CH C-CAP,S 82P-50 J CH CHIP CAPACITOR,0.01-25 CHIP CAPACITOR,0.01-25 CAP, ELECT 47-25V C-CAP,S 0.047-25 B CAP, ELECT 1-50V CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP, ELECT 47-25V C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP,CHIP 4700P CAP,CHIP 4700P
C121 C122 C123 C123 C124 C126 C126 C128 C128 C130 C130 C132 C133 C133 C135 C151 C152 C192 C193 C193 C201 C202 C202 C204 C204 C205 C206 C207
4
REF. NO C207 C301 C302 C302 C303 C401 C401 C402 C402 C403 C403 C404 C404 C405 C405 C406 C406 C407 C454 C454 C601 C602 C602 CN1 CN201
KANRI DESCRIPTION NO. 87-010-196-080 CHIP CAPACITOR,0.1-25 87-010-382-080 CAP, ELECT 22-25V 87-010-196-020 CHIP CAPACITOR,0.1-25 87-010-196-080 CHIP CAPACITOR,0.1-25 87-010-260-080 CAP, ELECT 47-25V 87-010-322-020 87-010-322-080 87-010-322-020 87-010-322-080 87-010-322-020 87-010-322-080 87-010-322-080 87-010-322-020 87-010-322-020 87-010-322-080 87-010-322-020 87-010-322-080 87-010-405-080 87-010-196-020 87-010-196-080 87-010-260-080 87-010-196-080 87-010-196-020 87-A60-429-010 84-ZG1-648-010 C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH CAP, ELECT 10-50V CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP, ELECT 47-25V CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CONN,16P H TOC-A CONN ASSY,6P
PART NO.
REF. NO CN202 CN501 CN601 CON401 FB601 FB602 LED601 M201 SW201 SW202 X101 LED. C.B LED501 LED502 LED503 LED504
KANRI DESCRIPTION NO. 87-A60-130-010 CONN,5P V 84-ZG1-647-010 CONN ASSY,2P 87-009-345-010 CONN,2P PH V 87-099-030-010 CONN,13P 6216H 87-008-372-080 FLTR,EMI BL01 RN1 87-008-372-080 87-A40-558-010 87-045-305-010 87-036-109-010 87-036-109-010 87-A70-046-010 FLTR,EMI BL01 RN1 LED,SLZ-8128A-01-A MOTOR, RF-500TB DC-5V (2MA) SW,MICRO SPPB61 SW,MICRO SPPB61 VIB,XTAL 16.934MHZ
PART NO.
87-A40-263-080 87-A40-263-080 87-A40-268-080 87-A40-268-080
LED,SLH-56PCT31 GRN LED,SLH-56PCT31 GRN LED,SLH-56DCT31 ORN LED,SLH-56DCT31 ORN
T-T C.B C401 CON401 M401 PS401 MOTOR C.B PIN3 SW1 91-564-722-110 91-572-085-110 CONN,PIN 6P LEAF SWITCH 87-018-214-080 86-NFZ-675-010 87-045-364-010 87-026-573-010 CAP TC U 0.1-50F CONN,5P H 6216-11H MOTOR(BCH3B14) SNSR,PHOTO GP1S53V
· Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Resistor Code Value of resistor Chip resistor
Dimensions (mm)
Figure
Wattage 1/16W 1/16W 1/10W 1/8W
Type 1005 1608 2125 3216
Tolerance 5% 5% 5% 5%
Symbol CJ CJ CJ CJ
Form
L W
L 1.0
t
W 0.5 0.8 1.25 1.6
t 0.35 0.45 0.45 0.55
:A Resistor Code : A
104 108 118 128
1.6 2 3.2
5
TRANSISTOR ILLUSTRATION
C B E 2SA1235F 2SC3052F DTC124XK ECB 2SA1980Y/G KTA1266GR G S
D
2SK2158
6
BLOCK DIAGRAM
RCHO LVSS, RVSS LCHO
XOUT
XIN
RVDD
TDO
PIN3
CON 401
7
8
WIRING
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
TO CD C.B CN201
D
TO MOTOR C.B PIN3
E
F
G
H
I
J
K 9 10
PIN3
SCHEMATIC DIAGRAM
IC101 LC78641E
M201 MOVE 3.6V
VDD/2V
11
12
TEST MODE
1. How to Start the CD Test Mode
While pressing the CD function key, connect the AC power plug to wall outlet. The test mode starts up and "CD TEST" appears on the display. *1 ...... When the focus search keeps running for 10 minutes or longer continuously, the driver IC heats up, and the protective circuit works so that the machine may stops operating. In this case, turn off the main power, wait for a while and restart the machine. *2 ...... Do not keep pressing the FF or RWD button while the pickup is located at the innermost or outermost circumference because the gear can be damaged as the sled motor keeps rotating.
2. How to Exit the CD Test Mode
Press the POWER button or disconnect the AC power plug from wall outlet. * When any function key other than PLAY is pressed during playback, the test mode is canceled.
4. Automatic Adjustment Result Display
The automatic adjustment values of the focus and the tracking can be displayed.
3. Function and Use of the CD Test Mode
NO 1 MODE Start mode How to enter the mode All indicators turn · All FL all ndicators turn on on 2 Search mode STOP button CD · LD turns on all the time · Focus search continuos operation · Spindle motor continuos kick · FL check · Microprocessor check · APC circuit check · Laser current measurement *1 · Focus search waveform check · Focus error waveform check (Ignores DRF during search mode) 3 Play mode PLAY button Normal · Normal playback · Focus search is continued if failed in TOC READ. 4 Traverse mode PAUSE button Normal · Tracking servo OFF/ON Repeats OFF/ON every time the PAUSE button is pressed 5 Sled mode FF button CD TEST · Moves PU to inner circumference Kicks the lens to inner circumference at the same time RWD button CD TEST · Moves PU to outer circumference Kicks the lens to outer circumference at the same time 6 Spindle mode TAPE REC button All indicators turn · Pressing the button once on rotates the spindle motor in the normal direction (rough speed). Pressing the button again rotates it in the reverse direction. Pressing it again stops the motor 7 RF AGC mode TUNER button AGC ON/OFF · Repeats ON/OFF every time · PU good or defective check the TUNER button is pressed 13 · RF AMP circuit check · Spindle circuit check · Spindle motor check *2 · Sled circuit check *2 · Tracking circuit check · Mechanism operation check · PU check · Tracking balance check · Each servo circuit is checked · DRF check Display Operation Check item
4-1. Automatic Adjustment Result Display of Focus Offset Cancel/Gain
1) Enter the start mode (all indicators turn on). 2) Press the TAPE button to display "F**" and set each of the adjustment item to either ON or OFF. (Refer to the following table.) 3) Press the PLAY button to play back the CD. 4) Press the CD button. 5) The automatic adjustment value "F** **" is displayed. (Refer to the following table.) 6) Upon completion of check, press the CD button twice to return to the play mode. Automatic adjustment value display (Asterisk * means hexadecimal display.) F F F F F OFFSET 0 1 1 0 GAIN 0 1 0 1 F F F F F OFFSET Not displayed ** ** Not displayed -- Not displayed Not displayed Not displayed Not displayed GAIN Not displayed ** Not displayed **
Adjustment item (ON = 1, OFF = 0)
4-2. Automatic Adjustment Result Display of Tracking Offset Cancel/Balance/Gain
1) 2) 3) 4) 5) 6) Enter the start mode (all indicators turn on). Press the AUX button to display "T***" and set each adjustment item to either ON or OFF. (Refer to the following table.) Press the PLAY button to play back the CD. Press the CD button twice. The automatic adjustment value "F******" is displayed. (Refer to the following table.) Upon completion of check, press the CD button to return to the play mode. Automatic adjustment value display (Asterisk * means hexadecimal display.) T T T T T T T T T OFFSET 0 1 1 1 1 0 0 0 BALANCE 0 1 1 0 0 1 1 0 GAIN 0 1 0 1 0 1 0 1 T T T T T T T T T OFFSET Not displayed ** ** ** ** Not displayed Not displayed Not displayed BALANCE Not displayed ** ** Not displayed Not displayed ** ** Not displayed GAIN Not displayed ** Not displayed ** Not displayed ** Not displayed **
Adjustment item (ON = 1, OFF = 0)
14
WAVE FORM
1 2
IC201 · (IN6-R) IC201 ª (IN6-F)
VOLT/DIV: 500mV TIME/DIV: 200mS
IC BLOCK DIAGRAM IC, BA5927S
1.6Vp-p
1 2
1.6Vp-p
3
Between CN202 1 and 2 (2 Pin: 0 Level)
VOLT/DIV: 1V TIME/DIV: 200mS
0
4
IC101 % (FE)
VOLT/DIV: 500mV TIME/DIV: 2mS
IC, LA9235M
1.75Vp-p
5
IC101 ^ (TE)
VOLT/DIV: 200mV TIME/DIV: 200µS
1.0Vp-p
15
16
IC DESCRIPTION IC, LC78641E
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Pin Name PDO1 PDO2 VVSS PCKIST VVDD FR HFL SLCIST SLCO EFMIN JITTV JITTC BH PH (RFENV) FE TE VREF ADAVDD ADAVSS PHREF BHREF TBLO TDO FDO SPDO SLDO DVREF/FG LASER CONT1 CONT2 CONT3 CONT4 CONT5 PCK C2F VDD DOUT FSX I/O O O -- -- -- -- I -- O I O O I I I I I -- -- O O O O O O O I/O O I/O I/O I/O I/O I/O O O -- O O Description Internal VCO control phase comparator output pin. (Pull down) Internal VCO control phase comparator output pin. OFF for rough servo, ON for phase servo. (Pull down) 41 Internal VCO ground pin. PDO output current adjustment resistor connection pin. Internal VCO power supply pin. VCO frequency range adjustment resistor connection pin. (Pull up) Mirror detection signal input pin. SLCO output current adjustment resistor connection pin. Control output. EFM signal input pin. Jitter detection monitor pin. Jitter detection adjustment pin. (Pull down) BH signal input pin. (Connected to GND) PH signal or RFENV signal input pin. FE signal input pin. TE signal input pin. VREF input pin. Servo A/D, D/A power supply pin. Servo A/D, D/A ground pin. PH reference output pin. (Not connected) BH reference output pin. (Not connected) Tracking balance output pin. Tracking control output pin. Focus control output pin. Spindle control output pin. Thread control output pin. Output driver VREF output pin. FG signal input pin. (Connected to GND) Laser ON/OFF control pin. General-purpose input/output pin 1. (Connected to GND) General-purpose input/output pin 2. (Connected to GND) General-purpose input/output pin 3. (Connected to GND) General-purpose input/output pin 4. General-purpose input/output pin 5. (Not connected) EFM data playback clock monitor pin. Average 4.3218MHz when the phase is locked. (Not connected) C2 flag output pin. (Not connected) Digital power supply pin. Digital out output pin. (EIAJ format) Output pin for the 7.35kHz synchronization signal divided from the crystal oscillator. (Not connected) 77 V/P O 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 SBSY PW SBCK CE CL DI DO INT WRQ RES DRF VDD5V VSS CONT6 CONT7 O O I I I I O O O I O -- -- I/O I/O 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 MUTEL MUTER LVDD LCHO LVSS RVSS RCHO RVDD XVDD XIN XOUT XVSS ASLRCK ASDACK ASDFIN LRSY DATACK DATA 16M SFSY O O -- O -- -- O -- -- I O -- I I I O O O O O Crystal oscillator ground pin. L/R clock input pin. (Connected to GND) Bit clock input pin. (Connected to GND) L/R channel data input pin. (Connected to GND) L/R clock output pin. (Not connected) Bit clock output pin. (Not connected) L/R channel data output pin. (Not connected) 16.9344MHz output pin. (Not connected) Subcode frame synchronization signal output pin. This signal falls when the subcode is in the standby state. (Not connected) Subcode clock synchronization signal output pin. (Not connected) Subcode P, Q, R, S, T, U and W output pin. (Not connected) Subcode readout clock input pin. (Connected to GND) Chip enable signal input pin. Data transfer clock input pin. Data input pin. Data output pin. Interruption signal output pin. (Not connected) Interruption signal output pin. Reset input pin. This pin must be set low briefly after power is first applied. Focus ON detect pin. Microprocessor interface power supply. Digital ground pin. General-purpose input/output pin 6. General-purpose input/output pin 7. Rough servo/phase control automatic switching monitor output pin. "H" for rough servo and "L" for phase servo. (Not connected) 17 18 EMPH I/O Pin No. 39 40 Pin Name EFLG TEST I/O O I Description C1, C2 error correction monitor pin. (Not connected) Test input pin. (Connected to GND) Emphasis pin. Which becomes an input pin after reset and can be controlled externally. This becomes an emphasis monitor pin under control by command. (Not connected) L channel mute output pin. (Not connected) R channel mute output pin. (Not connected) L channel power supply pin. L channel output pin. L channel ground pin. R channel ground pin. R channel output pin. R channel power supply pin. Crystal oscillator power supply pin. Connections for a 16.9344MHz crystal oscillator pin.
Pin No.
Pin Name
I/O
Description Synchronization signal detection output pin.
78
FSEQ
O
Outputs a high level when the synchronization signal detected from the EFM signal and the internally generated synchronization signal agree. (Not connected)
79 80
DEFECT EFMO
I/O O
Defect pin. Which becomes an input pin after reset and can be controlled externally. This becomes the defect monitor pin under control by command. (Not connected) EFM signal output pin. (Not connected)
19
MECHANICAL EXPLODED VIEW 1/1
28
29 30 A
14
27 26 31 25 19 24 23 21 20 P.C.B
13
12 11
22 C
B 10 a
a
32 9
4 8 18 7 6 P.C.B 17
3 P.C.B
4
5
CUSHION,CD880 1 2 16
15 33
15 CUSHION,CD880
20
MECHANICAL PARTS LIST 1/1
REF. NO 1 2 2 3 4 4 5 6 7 8
KANRI DESCRIPTION NO. 84-ZG1-225-010 BELT,SQ1.0-63.3 84-ZG1-673-010 F-CABLE,5P 1.25 210MM BLACK N 84-ZG1-672-010 F-CABLE,5P 1.25 210MM WHITE N 87-045-364-010 MOTOR(BCH3B14) 84-ZG1-267-010 PULLEY,LOAD MO 8 81-ZG1-212-010 84-ZG1-238-010 84-ZG1-248-010 84-ZG1-239-210 84-ZG1-008-210 PULLY,LOAD MO GEAR,WORM N SPR-C,WORM PULLY,WORM N TRAY,NO3 TRAY,NO3 BLU HLDR,MAGNET 23 HLDR,MAGNET N(J) HLDR,MAGNET NAT HLDR,MAGNET N SPR-P,WORM GEAR,MAIN TT GEAR,MAIN TT 4 LEVER,TT LEVER,TT NAT TURN TABLE,NO1 BLU TURNTABLE,NO1(*) S-SCREW,TT S-SCREW,MECH 880 FF-CABLE 16P-1.0 HLDR,MECHA NO3 HLDR,MECHA NO3 NAT MOTOR, RF-500TB DC-5V (2MA) SPR-E CAM S PLATE,MAGNET BLK
PART NO.
REF. NO 20 21 22 23 23 24 25 26 26 27 28 29 29 30
KANRI DESCRIPTION NO. 81-ZG1-255-110 PLATE,MAGNET MK2 83-ZG3-604-010 RING,MAG 2 83-ZG3-213-010 LVR,SW 84-ZG1-208-210 LEVER,CAM 84-ZG1-266-010 LEVER,CAN 8 84-ZG1-205-210 81-ZG1-291-110 84-ZG1-206-110 84-ZG1-274-010 84-ZG1-207-010 84-ZG1-209-010 84-ZG1-203-410 84-ZG1-215-410 84-ZG1-011-010 GEAR,TRAY (*) GEAR,TRAY RELAY NO3 GEAR,RELAY GEAR,RELAY 8 PULLEY,RELAY BELT,SQ1.8-117.7 GEAR,MAIN CAM GEAR,MAIN CAM BLU REFLECTOR,CD SLIDE,MECHA CAM YEL SLIDER,MECHA CAM CHAS,MECHA NAT CHAS,MECHA KSM-880CAB TAPPING SCREW, BVT2+3-10 BVT2+3-6 BLK U+2.6-3
PART NO.
8 8A-ZG1-001-010 9 8A-ZG1-210-010 9 84-ZG1-243-210 9 84-ZG1-289-010 9 81-ZG1-277-310 10 11 11 12 12 13 13 14 15 16 17 17 18 19 20 84-ZG1-259-010 84-ZG1-221-010 84-ZG1-269-010 84-ZG1-224-010 84-ZG1-288-010 8A-ZG1-002-010 84-ZG1-005-210 81-ZG1-239-010 8A-ZG1-201-010 85-NFT-611-110 84-ZG1-299-210 8A-ZG1-203-010 87-045-305-010 84-ZG1-211-010 84-ZG1-285-010
31 84-ZG1-216-310 31 32 32 33 A 84-ZG1-204-310 84-ZG1-286-010 84-ZG1-201-410 M8-ZZK-C90-070 87-067-703-010
B 87-067-981-010 C 87-251-070-410
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange
21
CD MECHANISM EXPLODED VIEW 1/1
8
6 4 5
7
A
9
10
11
2
3
P.C.B 1
CD MECHANISM PARTS LIST 1/1
REF. NO 1 2 3 4 5
KANRI DESCRIPTION NO. 91-564-722-110 CONN,PIN 6P 91-572-085-110 LEAF SWITCH 9X-264-655-010 SL MOTORR ASSY M8-ZZK-C90-070 KSM-880CAB 92-647-416-020 SPRING EXTENSION SHUTTER B NS SLIDE RACK
PART NO.
REF. NO 8 9 10 11 A
KANRI DESCRIPTION NO. 92-647-742-010 SPRING COMPRESSION 93-321-813-110 POLI WASHER 92-647-407-010 GEAR A 92-647-408-020 GEAR B 93-713-786-510 SCREW,+P2-3
PART NO.
6 92-647-595-020 7 92-647-732-010
22
REFERENCE NAME LIST ELECTRICAL SECTION
DESCRIPTION ANT CC-CAP C-CAP TN C-COIL C-DI C-DIODE C-FET C-FOTR C-JACK C-LED C-RES C-SFR C-SLIDE SW C-SW C-TR C-VR C-ZENER CAP, CER CAP, E CAP, M/F CAP, TC CAP, TC-U CAP, TN CERA FIL CF DL E/CAP FILT FLTR FUSE RES MOT P-DIODE P-SNSR P-TR POLY VARI PPCAP PT PTR, RES RC RES NF RESO SHLD SOL SPKR SW, LVR SW, RTRY SW, SL TC CAP THMS TR TRIMMER TUN-CAP VIB, CER VIB, XTAL VR ZENER REFERENCE NAME ANTENNAS CHIP CAP, CHIP CAP, CHIP TANTALUM COIL, CHIP DIODE, CHIP DIODE, CHIP FET, CHIP FILTER, CHIP JACK, CHIP LED, CHIP RES, CHIP SFR, CHIP SLIDE SWITCH, CHIP SWITCH, CHIP TRANSISTOR, CHIP VOLUME, CHIP ZENER, CHIP CAP, CERA-SOL CAP, ELECT CAP, FILM CAP, CERA-SOL CAP, CERA-SOL SS CAP, TANTALUM FILTER, CERAMIC FILTER, CERAMIC DELAY LINE CAP, ELECT FILTER FILTER RES, FUSE MOTOR PHOTO DIODE PHOTO SENSER PHOTO TRANSISTOR VARIABLE CAPACITOR CAP, PP POWER TRANSFORMER PTR, MELF REMOTE CONTROLLER RES, NON-FLAMMABLE RESONATOR SHIELD SOLENOID SPEAKER SWITCH, LEVER SWITCH, ROTARY SWITCH, SLIDE CAP, CERA-SOL THERMISTOR TRANSISTOR CAP, TRIMMER VARIABLE CAPACITOR RESONATOR, CERAMIC RESONATOR, CRYSTAL VOLUME DIODE, ZENER
MECHANICAL SECTION
DESCRIPTION ADHESHIVE AZ BAR-ANT BAT BATT BRG BTN CAB CASS CHAS CLR CONT CRSR CU CUSH DIR DUBB FL FLY-WHL FR FUN G-CU HDL HIMERON HINGE, BAT HLDR HT-SINK IB IDLE IND, L-R KEY, CONT KEY, PRGM KNOB, SL LBL LID, BATT LID, CASS LVR P-SP PANEL, CONT PANEL, FR PRGM PULLY, LOAD MO RBN SSEG SH SHLD-SH SL SP SP-SCREW SPACER, BAT SPR SPR-P SPR-PC-PUSH T-SP TERM TRIG TUN VOL W WHL WORM-WHL REFERENCE NAME SHEET ADHESHIVE AZIMUTH BAR-ANTENNA BATTERY BATTERY BEARING BUTTON CABINET CASSETTE CHASSIS COLLAR CONTROL CURSOR CUSHION CUSHION DIRECTION DUBBING FRONT LOADING FLYWHEEL FRONT FUNCTION G-CUSHION HANDOL CLOTH HINGE, BATTERY HOLDER HEAT SINK INSTRUCTION BOOKLET IDLER INDICATOR, L-R KEY, CONTROL KEY, PROGRAM KNOB, SLIDE LABEL LID, BATTERY LID, CASSETTE LEVER P-SPRING PANEL, CONTROL PANEL, FRONT PROGRAM PULLY, LOAD MOTOR RIBBON SPECIAL SEGMENT SHEET SHIELD-SHEET SLIDE SPRING SPECIAL-SCREW SPACER, BATTERY SPRING P-SPRING P-SPRING, C-PUSH T-SPRING TERMINAL TRIGGER TUNING VOLUME WASHER WHEEL WORM-WHEEL
23
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
0251431 Printed in Singapore