Text preview for : pc585.pdf part of DSC PC585 DSC PC585 Classic Installation manual



Back to : pc585.pdf | Home

· W A R N I N G ·
This manual contains information on limitations regarding product use and function and information on the
limitations as to liability of the manufacturer. The entire manual should be carefully read.




Installation
Manual




Software Version 2.1
DLS-1 v6.5 and up




Downloaded from www.Manualslib.com manuals search engine
LIMITED WARRANTY WARNING Please Read Carefully
Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve Note to Installers
months from the date of purchase, the product shall be free of defects in materials and This warning contains vital information. As the only individual in contact with system users, it is your
workmanship under normal use. During the warranty period, Digital Security Controls responsibility to bring each item in this warning to the attention of the users of this system.
Ltd. shall, at its option, repair or replace any defective product upon return of the product System Failures
to its factory, at no charge for labour and materials. Any replacement and/or repaired This system has been carefully designed to be as effective as possible. There are circumstances, how-
parts are warranted for the remainder of the original warranty or ninety (90) days, which- ever, involving fire, burglary, or other types of emergencies where it may not provide protection. Any
alarm system of any type may be compromised deliberately or may fail to operate as expected for a
ever is longer. The original owner must promptly notify Digital Security Controls Ltd. in variety of reasons. Some but not all of these reasons may be:
writing that there is defect in material or workmanship, such written notice to be received
s Inadequate Installation
in all events prior to expiration of the warranty period. A security system must be installed properly in order to provide adequate protection. Every installation
should be evaluated by a security professional to ensure that all access points and areas are covered.
International Warranty Locks and latches on windows and doors must be secure and operate as intended. Windows, doors,
The warranty for international customers is the same as for any customer within Canada walls, ceilings and other building materials must be of sufficient strength and construction to provide
and the United States, with the exception that Digital Security Controls Ltd. shall not be the level of protection expected. A reevaluation must be done during and after any construction activity.
An evaluation by the fire and/or police department is highly recommended if this service is available.
responsible for any customs fees, taxes, or VAT that may be due.
s Criminal Knowledge
Warranty Procedure This system contains security features which were known to be effective at the time of manufacture. It
is possible for persons with criminal intent to develop techniques which reduce the effectiveness of
To obtain service under this warranty, please return the item(s) in question to the point of these features. It is important that a security system be reviewed periodically to ensure that its features
purchase. All authorized distributors and dealers have a warranty program. Anyone re- remain effective and that it be updated or replaced if it is found that it does not provide the protection
turning goods to Digital Security Controls Ltd. must first obtain an authorization num- expected.
ber. Digital Security Controls Ltd. will not accept any shipment whatsoever for which s Access by Intruders
prior authorization has not been obtained. Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection
by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or
Conditions to Void Warranty prevent the proper operation of the system.
This warranty applies only to defects in parts and workmanship relating to normal use. It s Power Failure
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate
does not cover: power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail.
· damage incurred in shipping or handling; Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a
device operates only by AC power, any interruption, however brief, will render that device inoperative
· damage caused by disaster such as fire, flood, wind, earthquake or lightning; while it does not have power. Power interruptions of any length are often accompanied by voltage fluctua-
· damage due to causes beyond the control of Digital Security Controls Ltd. such as tions which may damage electronic equipment such as a security system. After a power interruption has
occurred, immediately conduct a complete system test to ensure that the system operates as intended.
excessive voltage, mechanical shock or water damage;
s Failure of Replaceable Batteries
· damage caused by unauthorized attachment, alterations, modifications or foreign objects; This system's wireless transmitters have been designed to provide several years of battery life under normal
conditions. The expected battery life is a function of the device environment, usage and type. Ambient
· damage caused by peripherals (unless such peripherals were supplied by Digital Secu- conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the
rity Controls Ltd.); expected battery life. While each transmitting device has a low battery monitor which identifies when the
· defects caused by failure to provide a suitable installation environment for the prod- batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance
will keep the system in good operating condition.
ucts;
s Compromise of Radio Frequency (Wireless) Devices
· damage caused by use of the products for purposes other than those for which it was Signals may not reach the receiver under all circumstances which could include metal objects placed on or
designed; near the radio path or deliberate jamming or other inadvertent radio signal interference.
s System Users
· damage from improper maintenance; A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary
· damage arising out of any other abuse, mishandling or improper application of the physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is
products. important that all system users be trained in the correct operation of the alarm system and that they
know how to respond when the system indicates an alarm.
Digital Security Controls Ltd.'s liability for failure to repair the product under this war- s Smoke Detectors
ranty after a reasonable number of attempts will be limited to a replacement of the prod- Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of
uct, as the exclusive remedy for breach of warranty. Under no circumstances shall Digital reasons, some of which follow. The smoke detectors may have been improperly installed or positioned.
Security Controls Ltd. be liable for any special, incidental, or consequential damages Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs,
or on the other side of closed doors. Smoke detectors may not detect smoke from fires on another level of
based upon breach of warranty, breach of contract, negligence, strict liability, or any the residence or building.
other legal theory. Such damages include, but are not limited to, loss of profits, loss of Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot
the product or any associated equipment, cost of capital, cost of substitute or replace- sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by
ment equipment, facilities or services, down time, purchaser's time, the claims of third carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage
parties, including customers, and injury to property. of flammable materials, overloaded electrical circuits, children playing with matches or arson.
Even if the smoke detector operates as intended, there may be circumstances when there is insufficient
Disclaimer of Warranties warning to allow all occupants to escape in time to avoid injury or death.
This warranty contains the entire warranty and shall be in lieu of any and all other s Motion Detectors
warranties, whether expressed or implied (including all implied warranties of mer- Motion detectors can only detect motion within the designated areas as shown in their respective installa-
tion instructions. They cannot discriminate between intruders and intended occupants. Motion detectors
chantability or fitness for a particular purpose) And of all other obligations or li- do not provide volumetric area protection. They have multiple beams of detection and motion can only be
abilities on the part of Digital Security Controls Ltd. Digital Security Controls Ltd. detected in unobstructed areas covered by these beams. They cannot detect motion which occurs behind
neither assumes nor authorizes any other person purporting to act on its behalf to walls, ceilings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether
modify or to change this warranty, nor to assume for it any other warranty or liabil- intentional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors,
ity concerning this product. windows or any other part of the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effective-
This disclaimer of warranties and limited warranty are governed by the laws of the ness can be reduced when the ambient temperature rises near or above body temperature or if there are
province of Ontario, Canada. intentional or unintentional sources of heat in or near the detection area. Some of these heat sources
could be heaters, radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.
WARNING: Digital Security Controls Ltd. recommends that the entire system be com- s Warning Devices
pletely tested on a regular basis. However, despite frequent testing, and due to, but not Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if
there is an intervening wall or door. If warning devices are located on a different level of the residence or
limited to, criminal tampering or electrical disruption, it is possible for this product to premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be
fail to perform as expected. interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances,
or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired person.
Installer's Lockout s Telephone Lines
Any products returned to DSC which have the Installer's Lockout option enabled and If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of
exhibit no other problems will be subject to a service charge. time. Also an intruder may cut the telephone line or defeat its operation by more sophisticated means
which may be difficult to detect.
Out of Warranty Repairs s Insufficient Time
Digital Security Controls Ltd. will at its option repair or replace out-of-warranty prod- There may be circumstances when the system will operate as intended, yet the occupants will not be
protected from the emergency due to their inability to respond to the warnings in a timely manner. If the
ucts which are returned to its factory according to the following conditions. Anyone system is monitored, the response may not occur in time to protect the occupants or their belongings.
returning goods to Digital Security Controls Ltd. must first obtain an authorization num- s Component Failure
ber. Digital Security Controls Ltd. will not accept any shipment whatsoever for which Although every effort has been made to make this system as reliable as possible, the system may fail to
prior authorization has not been obtained. function as intended due to the failure of a component.
s Inadequate Testing
Products which Digital Security Controls Ltd. determines to be repairable will be repaired Most problems that would prevent an alarm system from operating as intended can be found by regular
and returned. A set fee which Digital Security Controls Ltd. has predetermined and which testing and maintenance. The complete system should be tested weekly and immediately after a break-
may be revised from time to time, will be charged for each unit repaired. in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction
activity inside or outside the premises. The testing should include all sensing devices, keypads, con-
Products which Digital Security Controls Ltd. determines not to be repairable will be soles, alarm indicating devices and any other operational devices that are part of the system.
replaced by the nearest equivalent product available at that time. The current market s Security and Insurance
price of the replacement product will be charged for each replacement unit. Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm
system also is not a substitute for property owners, renters, or other occupants to act prudently to prevent
or minimize the harmful effects of an emergency situation.


Downloaded from www.Manualslib.com manuals search engine
Table of Contents
PC585 Control Panel Wiring Diagram ii 5.8 Communicator ­ Reporting Codes ................................... 17
5.9 Communicator ­ Reporting Formats ................................. 18
Section 1: System Introduction 1 5.10 Downloading ..................................................................... 19
1.1 Specifications ...................................................................... 1 5.11 PGM Output Options ......................................................... 20
1.2 Additional Devices .............................................................. 2 5.12 Telephone Line Monitor (TLM) .......................................... 22
1.3 Out of the Box ..................................................................... 2 5.13 Siren .................................................................................. 22
Section 2: Getting Started 3 5.14 Test Transmission .............................................................. 22
5.15 Transmission Delay ........................................................... 22
2.1 Installation Steps ................................................................. 3
5.16 Fire, Auxiliary and Panic Keys .......................................... 23
2.2 Terminal Descriptions .......................................................... 3
5.17 Arming/Disarming Options ............................................... 23
2.3 Keybus Operation and Wiring ............................................. 4
5.18 Entry/Exit Delay Options ................................................... 23
2.4 Current Ratings ­ Modules and Accessories ..................... 4
5.19 Swinger Shutdown ............................................................ 24
2.5 Keypad Assignment ............................................................ 4
5.20 Event Buffer ....................................................................... 24
2.6 Supervision .......................................................................... 5
5.21 Keypad Lockout Options .................................................. 24
2.7 Removing Modules ............................................................. 5
5.22 Keypad Blanking ............................................................... 24
2.8 Zone Wiring ......................................................................... 5
5.23 Keypad Backlighting ......................................................... 24
2.9 Fire Zone Wiring .................................................................. 6
5.24 Loop Response ................................................................. 24
2.10 LINKS Zone Wiring .............................................................. 6
5.25 Keypad Tampers ............................................................... 24
2.11 Keypad Zones ..................................................................... 6
5.26 LINKS1000 Cellular Communicator .................................. 25
Section 3: Keypad Commands 8 5.27 Additional System Modules .............................................. 25
3.1 Arming and Disarming ........................................................ 8 5.28 Clock Adjust ...................................................................... 25
3.2 Auto Bypass ­ Stay Arming ................................................ 8 5.29 Timebase .......................................................................... 26
3.3 Automatic Arming ............................................................... 8 5.30 Resetting Factory Defaults ................................................ 26
3.4 [D] Commands .................................................................... 8 5.31 Installer's Lockout ............................................................. 26
3.5 Function Keys ................................................................... 11 5.32 Walk Test (Installer) ........................................................... 26
3.6 Features Available for the LCD5500Z ............................... 11 Programming Worksheets 27
Section 4: How to Program 12 For the Record ............................................................................ 27
4.1 Installer's Programming .................................................... 12 Keypad Programming ................................................................ 28
4.2 Programming Decimal Data .............................................. 12 Basic Programming .................................................................... 28
4.3 Programming HEX Data .................................................... 12 Advanced System Programming ................................................ 31
4.4 Programming Toggle Option Sections .............................. 13 Communicator Programming ..................................................... 33
4.5 Viewing Programming ....................................................... 13 Downloading Options ................................................................. 38
International Programming ......................................................... 39
Section 5: Program Descriptions 14 Module Programming ................................................................. 39
5.1 Programming Security Codes ........................................... 14 Special Installer Functions .......................................................... 39
5.2 Zone Programming ........................................................... 14
5.3 Zone Attributes .................................................................. 15 Appendix A: Reporting Codes 40
5.4 Assigning Keypad Zones .................................................. 16 Appendix B: Programming LCD Keypads 42
5.5 Communicator ­ Dialing .................................................... 16
5.6 Communicator ­ Account Numbers .................................. 16 PC585 v2.1 Module Compatibility Back Cover
5.7 Communicator ­ Telephone Numbers .............................. 16
Limited Warranty, Warning Inside Front Cover




i


Downloaded from www.Manualslib.com manuals search engine
PC585 Control Panel Wiring Diagram



PC585 Control Panel Wiring Diagram
Incorrect connections may
result in fuse failure or improper
operation. Inspect wiring and
ensure connections are correct
before applying power. Do not
route any wiring over circuit
boards. Maintain at least 1"
(25.4mm) distance.




TM




ii

Downloaded from www.Manualslib.com manuals search engine
System Introduction
S E C T I O N 1


1.1 Specifications Digital Communicator Specifications
· Supports major communication formats including SIA and
Downloading Software Support Contact ID
· PC585 uses DLS-1 v6.5 and up.
· Event-initiated personal paging
Flexible Zone Configuration · Three programmable telephone numbers
· Four fully programmable zones; system expandable to eight · Two account numbers
zones using keypad zone inputs and wireless zones · Supports LINKS1000 cellular communication
· 38 access codes: one master code, one maintenance code, · Supports LINKS2X50 Long Range Radio Transmitter
two duress codes, two supervision codes and 32 general
· DTMF and pulse dialing
access codes
· DPDT line seizure
· 27 zone types; 8 programmable zone attributes
· Anti-jam feature
· Normally closed, single EOL and double EOL zone wiring
· Split reporting of selected transmissions to each telephone
· Eight wireless zones available using the PC5132 Wireless
number
Receiver
System Supervision Features
Audible Alarm Output
The PC585 continuously monitors a number of possible trouble
· 700mA Supervised Bell Output (current limited at 3 amps),
conditions including:
12VDC
· AC power failure
· Steady or Pulsed Output
· Trouble by zone
EEPROM Memory · Tamper by zone
· Does not lose programming or system status on complete AC · Fire trouble
and Battery failure
· Telephone line trouble
Programmable Outputs · Failure to communicate
· Two programmable voltage outputs; 18 programmable options · Low battery condition
· PGM1 = 300mA; PGM2 = 50mA · Bell output trouble
Powerful 1.5 Amp Regulated Power Supply · Module fault (supervisory or loss of internal clock)
· 550 mA Auxiliary Supply, 12 VDC · AUX Power Supply Trouble
· Positive Temperature Coefficient (PTC) components replace False Alarm Prevention Features
fuses · Audible Exit Delay
· Supervision for loss of AC power, low battery · Audible Exit Fault
· Internal clock locked to AC power frequency · Communication Delay
Power Requirements · Urgency on Entry Delay
· Transformer = 16.5 VAC, 1.5A · Quick Exit
· Battery = 12 volt 4 Ah minimum rechargeable sealed lead · Cross Zone Burglary Alarm
acid battery · Rotating Keypress Buffer
Remote Keypad Specifications Additional Features
· Three keypads available: · Auto Arm at specified time
- PC1555RKZ eight zone LED keypad with zone input · Keypad-activated alarm output and communicator test
- PC5508Z eight zone LED keypad with zone input · All modules connect to the system via a four wire Keybus up
- LCD5500Z Alphanumeric keypad with zone input to 1000'/305m from main panel
· All keypads have five programmable function keys · An event buffer which records the past 128 events with both
· Connect up to eight keypads the time and date at which they occurred; buffer can be
· 4-wire (Quad) connection to Keybus printed using PC5400 serial interface module, or viewed with
· Built in piezoelectric buzzer the LCD5500Z keypad.
· Supports the addition of the PC5132 Wireless receiver for
integration of wireless devices
· Uploading and downloading capability
· Local downloading capability through the use of the PC-LINK
adaptor
· Added Keybus fault protection: clock and data outputs have
been programmed to withstand shorts to +12v to prevent
control panel damage




1


Downloaded from www.Manualslib.com manuals search engine
S Y S T E M V I N T R O D U C T I O N



1.2 Additional Devices LINKS2X50
In addition to the information below, see the back cover for a Either the LINKS2150 or LINKS2450 may be used to transmit
DSC module compatibility table. alarm information over a long range radio network.

PC5132 Wireless Receiver Cabinets
The PC5132 Wireless Receiver can be used to connect up to 8 Several different cabinets are available for the PC585 modules.
wireless devices to the system. All devices are spread spectrum, They are as follows:
900 MHz, fully supervised devices which use standard `AAA' or PC5003C Cabinet
`AA' alkaline batteries. Main control cabinet for the PC585 main panel. Dimensions
Seven additional devices are available. They are as follows: 288mm x 298mm x 78mm / 11.3" x 11.7" x 3" approximately.
WLS904 Wireless Motion Detector PC500 Cabinet
WLS905 Wireless Universal Transmitter Main control cabinet for the PC585 main panel. Dimensions
Adds wireless door or window contacts to your system. 213mm x 235mm x 78mm / 8.4" x 9.25" x 3" approximately.
WLS906 Wireless Smoke Detector PC5004C Cabinet
WLS907 Wireless Slimline Universal Transmitter Cabinet to house the PC5400 Printer Module. Dimensions
229mm x 178mm x 65mm / 9" x 7" x 2.6" approximately.
A smaller wireless door or window contact.
WLS908 Wireless Panic Pendant 1.3 Out of the Box
Adds personal protection to the system. When used, the unit will Please verify that the following components are included in
indicate a non-medical emergency to the central station. your system:
WLS909 Wireless Key · one PC500 main control cabinet
Adds a simple and mobile method of arming and disarming to the · one PC585 main control circuit board
system, as well as one-button access to several programmable · one PC1555RKZ keypad with zone input
functions. · one Installation Manual with programming worksheets
WLS910 Wireless Handheld Keypad · one Instruction Manual for the end user
· one hardware pack consisting of:
PC5400 Printer Module
- one mylar cabinet label
The PC5400 Printer Module will allow the panel to print out all
- four plastic circuit board standoffs
events that occur on the system to any serial printer. The - ten 5600 (5.6K) resistors
printout will contain the time, date and the event that occurred. - one 2200 (2.2K) resistor
LINKS1000 Cellular Communicator - one 1000 (1K) resistor
The LINKS1000 Cellular Communicator can be used three - ground connection assembly
different ways: as the sole communicator for the panel, as a - one cabinet door plug
backup for either or both telephone numbers or as a redundant
backup to the land line communicator where the panel will call
both the land line and via the LINKS.




2


Downloaded from www.Manualslib.com manuals search engine
Getting Started
S E C T I O N 2


The following sections provide a thorough description of how to Step 10: Testing the System
wire and configure devices and zones. The panel must be thoroughly tested to ensure that all features
and functions are operating as programmed.
2.1 Installation Steps
Read this section completely before you begin. Once you have 2.2 Terminal Descriptions
an overall understanding of the installation process, carefully Battery Connection
work through each step. A 12V 4Ah rechargable battery is used as a backup source of
Step 1: Create a Layout power in the event of an AC power failure. The battery also
Draw a rough sketch of the building to get an idea of where all provides additional current when the panel's demands exceed
alarm detection devices, keypads and other modules are to be the power output of the transformer, such as when the panel is
located. in alarm.
Step 2: Mounting the Panel The High Current Charge/Standard Battery Charge option
Locate the panel in a dry area close to an unswitched AC power (section [701], option [7]) allows you to choose between a high
source and the incoming telephone line. Before attaching the current battery charge and the standard battery charge rate.
cabinet to the wall, be sure to press the four circuit board
mounting studs into the cabinet from the back. After you have Do not connect the battery until all other wiring is
complete. Connect the battery before connecting
attached the cabinet to the wall, stick the provided DSC logo
the AC.
sticker on the front of the cabinet.
Connect the RED battery lead to the positive battery terminal;
You must complete all wiring before connecting connect the BLACK lead to negative.
the battery, or applying AC to the panel.
AC Terminals ­ AC
Step 3: Wiring the Keybus (Section 2.3) The panel requires a 16.5 volt, 1.5 VA transformer. Connect the
Wire the Keybus to each of the modules following the guidelines transformer to an unswitched AC source and connect the
provided in Section 2.3 of this manual. transformer to these terminals.
Step 4: Zone Wiring (Section 2.8) The panel can be programmed to accept a power line frequency
You must power down the control panel to complete all zone of either 50Hz AC or 60Hz AC in programming section [701],
wiring. Please refer to Section 2.8 when connecting zones using option [1].
normally closed loops, single EOL resistors, double EOL resistors,
Do not connect the transformer until all other
Fire zones and Keyswitch Arming zones.
wiring is complete.
Step 5: Complete Wiring (Section 2.2)
Complete all other wiring including bells or sirens, telephone Auxiliary Power Terminals ­ AUX+ and AUX-
line connections, and ground connections following the These terminals provide up to 550 mA of additional current at 12
guidelines provided in Section 2.2 ("Terminal Descriptions"). VDC for devices requiring power. Connect the positive side of
any device requiring power to the AUX+ terminal, the negative
Step 6: Power up the Control
side to AUX- (ground). The AUX output is protected. This means
Once all zone and Keybus wiring is complete, power up the
that if too much current is drawn from these terminals (such as
control panel. First, connect the red battery lead to the positive
a wiring short), the panel will temporarily shut off the output until
terminal and the black lead to negative. Then, connect the AC.
the problem is corrected.
Connect the battery before connecting the AC. Bell Output Terminals ­ BELL+ and BELL-
The panel will not power up on the battery These terminals provide up to 700 mA of continuous current at
connection alone.
12 VDC for powering bells, sirens, strobes or other warning-type
Step 7: Keypad Assignment (Section 2.5) equipment. Connect the positive side of any alarm warning
In order for keypads to be properly supervised, each must be device to BELL+, the negative side to BELL­. Please note that
assigned to a different slot. Please follow the guidelines provided the Bell output is protected: if too much current is drawn from
in Section 2.5 when assigning keypads. these terminals (such as a wiring short), the Bell PTC will open.
Three amps can be drawn for short periods only.
Step 8: Supervision (Section 2.6)
The Bell output is supervised. If no alarm warning devices are
The supervision of every module by the panel is automatically in use, connect a 1000 resistor across BELL+ and BELL­ to
enabled upon power up. Please verify that all modules appear prevent the panel from displaying a trouble condition. For more
on the system according to the instructions in Section 2.6. information, please refer to Section 3.4 ("[D] [2] Trouble Display").
Step 9: Programming the System (Sections 4 and 5) Keybus Terminals ­ AUX+, AUX-, YEL, GRN
Section 4 explains how to program the panel. Section 5 contains The Keybus is used by the panel to communicate with modules
a complete description of the various programmable features, and vice versa. Each module has four Keybus terminals that
which options are available and how they function. The must be connected to the four Keybus terminals on the panel.
Programming Worksheets should be filled out completely before For more information, see Section 2.3 ("Keybus Operation and
attempting to program the system. Wiring").


3


Downloaded from www.Manualslib.com manuals search engine
G E T T I N G S T A R T E D



Programmable Output Terminals ­ PGM1 and · No module can be more than 1,000'/305m (in wire length)
PGM2 from the panel.
Each PGM output is designed so that when activated by the · Shielded wire should not be used.
panel, the terminal will switch to ground.
Example of Keybus Wiring
PGM1 can sink up to 300mA of current.
Connect the positive side of the LED or NOTE: B
buzzer to AUX+, the negative side to Module (A) is correctly
150'
PGM1. If more than 300 mA of current are wired within 1,000'/305m of
required, a relay must be used. Please wire from the panel. 500' C
150'
study PGM wiring in the accompanying Module (B) is correctly
diagram.
PGM2 operates similarly to PGM1.
wired within 1,000'/305m of
wire from the panel.
PANEL
500' A
However, PGM2 can only sink up to 50mA Module (C) is NOT wired correctly as it is further than 1,000'/
of current. For a list of the programmable 305m from the panel, in wire distance.
output options, please see Section 5.11
"PGM Output Options." 2.4 Current Ratings ­ Modules and
Accessories
Zone Input Terminals ­ Z1 to Z4
Each detection device must be connected to a zone on the In order for the PC585 system to operate properly, the power output
control panel. We suggest that one detection device be capabilities of the main control and the expansion devices must not
connected to each zone; wiring multiple detection devices to a be exceeded. Use the data presented below to ensure that no part
single zone, however, is possible. For zone wiring specifics, of the system is overloaded and cannot function properly.
please see Section 2.8 ("Zone Wiring"). PC585 (12 VDC)
AUX+: ........... 550mA: Subtract the listed rating for each keypad,
Telephone Connection Terminals ­ expansion module and accessory connected to
TIP, RING, T-1, R-1 AUX+ or Keybus.
If a telephone line is required for central station communication
BELL: ........... 700mA continuous rating; 3.0A short term.
or downloading, connect an RJ-31X telephone jack in the
Available only with standby battery connected.
following manner:
PC585 Device Ratings (at 12 VDC)
· LCD5500Z Keypad: 75-85mA
· PC1555RKZ Keypad: 75-85mA
· PC5508Z Keypad: 75-85mA
· PC5400 Serial Module: 65mA
· PC5132 Wireless Receiver: 125mA
Other Devices
Please read the manufacturer's literature carefully to determine
For proper operation, no other telephone equipment the maximum current requirements for each device--during
should be connected between the control panel and activation or alarm--and include the proper values for loading
the telephone company facilities. Do not connect the calculations. Connected devices must not exceed system
alarm panel communicator to telephone lines capabilities during any possible operational mode.
intended for use with a fax machine. These lines may
incorporate a voice filter which disconnects the line 2.5 Keypad Assignment
if anything other than fax signals are detected,
There are eight available slots for keypads. LED keypads by
resulting in incomplete transmissions.
default are always assigned to slot 1. LCD5500Z keypads are
always assigned to slot 8. You will need to assign each keypad
2.3 Keybus Operation and Wiring to its own slot (1 to 8). Keypad assignment is required, as it tells
The Keybus is used by the panel to communicate with all the panel which slots are occupied. The panel can then generate
connected modules and vice versa. The red (AUX+) and black a fault when a keypad supervisory is not present.
(AUX-) terminals are used to provide power, while the yellow
(YEL) and green (GRN) terminals are clock and data respectively. One LCD keypad must be assigned to slot 8 in
order to upload keypad programming using
The four Keybus terminals of the panel must be DLS-1 software.
connected to the four Keybus terminals or wires
of all modules. How to Assign Keypads
Do the following at each keypad installed on the system:
The following restrictions apply to Keybus wiring:
· Keybus should be run in minimum 22 gauge quad (0.5mm); 1. Enter [D][8][installer's code] to go to installer programming
two pair twist is preferred. 2. Enter [000] for Keypad Programming
· The modules should be home-run to the panel but can be 3. Enter [0] for Slot Assignment
connected in series or T-tapped. 4. Enter a two digit number (11-18) to specify which supervisory
· Any module can be connected anywhere along the Keybus. You slot the keypad will occupy.
do not need to run a separate Keybus wire for keypads, etc. 5. Press [#] twice to exit installer programming.



4


Downloaded from www.Manualslib.com manuals search engine
G E T T I N G S T A R T E D



After assigning all keypads, perform a supervisory reset by If you change the zone supervision options from
entering section [902] in installer's programming. The panel will DEOL to EOL or from NC to DEOL (section [013],
now supervise all assigned keypads and enrolled modules on options [1] or [2]), you should power down the
the system. system completely, and then power it back up. If
How to Program Function Keys you do not, the zones may not work correctly.
By default, the 5 function keys on each keypad are programmed
Normally Closed (NC) Loops
as Stay Arm (03), Away Arm (04), Chime (06), Quick Exit (14)
and Sensor Reset (16). You can change the function of each key
on every keypad:
1. Go to the keypad where you want to change the function key
programming and enter Installer Programming.
2. Press [000] for Keypad Programming.
3. Enter [1] to [5] to select a function key to program.
4. Enter the 2 digit number, [00] to [17] to select the feature you
want the function key to have. For a complete list of Function To enable normally closed loops, programming section [013],
Key options See Section 3.5 "Function Keys" . option [1] must be ON.
5. Continue from step 3 until all function keys are programmed.
This option should only be selected if Normally
6. To exit Installer Programming, press [#] twice.
Closed (NC) detection devices or contacts are
2.6 Supervision being used.
By default, all modules are supervised upon installation. Single End Of Line (EOL) Resistors (5600)
Supervision is enabled at all times so that the panel can indicate To enable panel detection of single end of line resistors,
a trouble if a module is removed from the system. programming section [013], options [1] and [2] must be OFF.
To check on which modules are currently connected and
supervised, enter programming section [903] from installer's
programming. The LCD keypad will allow you to scroll through
the display of connected modules. A connected module which
does not show as being present will appear as a trouble
condition and the Trouble light on the keypad will turn ON. This
condition may be due to one or more of the following reasons:
· the module is not connected to the Keybus
· there is a Keybus wiring problem
· the module is more than 1,000'/305m from the panel
· the module does not have enough power
For more information regarding module supervision troubles,
please refer to Section 3.4 ("[D] [2] Trouble Conditions").
2.7 Removing Modules
The panel must be instructed to no longer supervise a module
being removed from the system. To remove the module, disconnect This option should be selected if either Normally
it from the Keybus and reset the supervision field by entering [902] Closed (NC) or Normally Open (NO) detection
devices or contacts are being used.
in the installer's programming. The panel will be reset to recognize
and supervise all existing modules on the system. Double End of Line (DEOL) Resistors
2.8 Zone Wiring Double End of Line resistors allow the panel to determine if the
For a complete description of the operation of all zone types, zone is in alarm, tampered or faulted.
please refer to Section 5.2 ("Zone Programming"). To enable panel detection of double end of line resistors,
There are several different ways in which zones may be wired, programming section [013], option [1] must be OFF and option
depending on which programming options have been selected. [2] must be ON.
The panel can be programmed to supervise normally closed, End
If the Double EOL supervision option is enabled,
of Line, or Double End of Line loops. Please refer to the following all hardwire zones on the main panel must be
diagrams to study each type of individually supervised zone wiring. wired for Double EOL resistors, except for Fire
and 24 Hour Supervisory zones.
Any zone programmed for Fire or 24 Hour Supervi-
sory must be wired with a single End of Line (EOL) Do not wire DEOL resistors on keypad zones.
resistor regardless of the type of zone wiring
supervision selected for the panel (section [013]: Do not use DEOL resistors for Fire zones or 24
[1] -[2]). See Section 5.2 "Zone Programming." Hour Supervisory zones. Do not wire Fire zones
to keypad zone terminals if the DEOL supervision
option is selected.



5


Downloaded from www.Manualslib.com manuals search engine
G E T T I N G S T A R T E D



LINKS Supervision (24 Hour Supervisory)
When using the LINKS1000
cellular communicator, any main
board zone may be configured
for LINKS Supervision. Program
this zone as zone type [09], 24