Text preview for : p39-46.pdf part of Philips p39-46 Philips Monitor Monitor CD 2001[1].part02 Monitor CD 2001 E-MANUALS Philips crt 104s PDF p39-46.pdf
Back to : p39-46.pdf | Home
Repair flow chart 104S CM23 GSIII 39
Go to cover page
A. Power Supply Failure
1. Sympton :
check 7103 pin7 check 7103
no startup sound Ok
100V LED light off
NO Ok
check check
NO
1101/6101/ 6115/3125/
7102/2105 3126/7102
check
check
replace 7103 7112/7104
Pin2>2.5V
/6111
Turn power off
2. Sympton :
check the resistance for
hicup mode with check 7103
all output voltages+180, OK
startup sound or pin 3 normal ?
80,12,-12,+6,+5,+8 V
blinking LED
check 6172/6157/6158
6160/6161 short? No
OPP possibly active
check 3125,3116,3117,
3118,6110,6109
OK
replace 5110
7103 pin7
check 7156 pin3 check 7156 pin1
Ok No possibly active by
voltage dip
7153 pinC shorted
No
Ok
check
check check CPU pin 10
7160/7161
+8V loading current and 7809 Base
7112/7123
check check 7102 check
3. Sympton:
frequency Ok drain waveform No 6105/3111
abnormal sound
F@40KHZ right? 2107/2126
No Ok
Check replace 5110
3131,2110,2111
Back Forward
40 104S CM23 GSIII Repair Flow Chart
Go to cover page
rough check for R,G, B
B.Video 1. video input= 0.7V
Repair Flow 2. 7099video output waveform check blanking
3. 1005 video output waveform 7501 pin16
Ok
check
1.Sympton :
R,G,B output
(with wite pattern) check heater check check
Ok No 1005 pin11
no picture =+6V EHT=24.5KV VG1 < -178V
1005 pin8
green LED on
1005 pin6
No
Ok
check Xray prot.
7501 pin2 check DC restoration
check
7013,,7033,7053
VG2 > 350V
7014,7034,7054
check blanking
7051 pin16
Ok
2.Sympton :
no video (or dim), check Vg1 check cathod
No turn down Vg2
only raster with/without retrace line Vg1 = 0V +80V,+180V
green LED on
check 7011,
check 7099 7031,7051 check 7012,7032,7052
check 7099 pin24
Ok pin 6,8,10 pin Base Pin Collector
ABL
input swing input swing Swing
No
replace IF
check 7099 cable
pin11 HFLB
check Check 7099
No Ok replace 7099
7501 pin16 pin5 CLBL
Back Forward
Repair Flow Chart 104S CM23 GSIII 41
Go to cover page
C. Horizontal deflection
output repair flow :
1. Sympton :
check B+DRV check B+DRV check H-Output
without
7623 gate 7621 base 7501 pin8
H-deflection.
check check B+DRV check B+DRV
replace 5612 Ok Ok
180V 7623 drain 7501 pin6
No No
check
refer to 7501 check list
6631,6632,3642
or replace 7501
check 2629, check
2. Sympton : 2610 7610,7611, check 7501
East /West parabola pin11 Refer to 7501
7612 check list
corr. exist parabola exist parabola exist
Back Forward
42 104S CM23 GSIII Repair Flow Chart
Go to cover page
basic check
D. Vertical Deflection Failure
+12/-12V
Sympton : check
check
one horizontal line 3403,3410
Ok 6401,6403
V_size is abnormal Good? Good?
too large/small
No No
Ok
Check Replace
7401,3403,3410 7401,6401,6403
check 7401
check
Ok pin2,pin3 ramp
2406,2413
exist ?
No
check
7501
Back Forward
Repair Flow Chart 104S CM23 GSIII 43
Go to cover page
check cpu pin4=5V
E. CPU
Basic Check Pin6/pin7=4MhZ
check list
Pin5=gnd
check pin2
ABL-CON
pwm from 0V to 5V
Hor. Freq.(KHz) Q3 Q2 Q1
11,12,13 check Q1-Q3 ~27.00 0 0 0
27.50~33.24 0 0 0
(Q3,Q2,Q1) Pin13/pin12/pin11 33.24~36.51 0 0 1
low : 0 36.51~42.38 1 1 0
S-cap switch hi :1 42.38~47.48 1 0 1
47.48~53.10 1 0 1
53.10~58.25 1 1 1
1. Normal
check sync. Fvout=Fvin
27,28,21,20 Hin=pin27 Fhout=Fhin
Vin=pin28
Hsync/Vsync Hout=pin21 2. sync out of rang
Vout=pin20 Fhin>54KHz
Fvin>120Hz
check pin10
10. Hunlock normal=Hi
blank=low
pin14 pin17
14, 17 P.S. normal hi hi
check pin14/17
LED standby low hi
off low low
Back Forward
44 104S CM23 GSIII Repair Flow Chart
Go to cover page
check
24. Degauss Active=low
no active=hi
check check
3. Reset
from 5V to 0V 7808/6813/3812
check key Check
19. Keypad 3838~3844
+,-,H-Shift,H-Size,V-Shift,V-Size keys
check pin26
1.no H/V sync & IF cable pin5 floating - show msg.
26. Selftest 2.H/V sync exist & IF cable pin5 to ground - normal
3.H/V sync non-exist & IF cable pin5 to gnd - power saving
check idle status
8,9. DDC bus Sda=pin9=hi
Scl=pin8=hi
check
check idle status 7806 24W04
22,23. IIC bus Sda=pin22=hi 7501 TDA4857
Scl=pin23=hi 7099 TDA4886
check pin15 pin16
15,16. EEPROM write : low hi
write protection read : don't care
normal : hi low
Back Forward
Repair Flow Chart 104S CM23 GSIII 45
Go to cover page
Basic check
F. TDA4857 Vcc=pin9=pin10=12V
Vcc > 9V
Check List gnd =pin7=pin25=0v
during startup
1. HFLB pin16
if no exist
(from H.defl) CLBL=hi
pin17 = Hunlock = floating
pin30 = Hpll2 = 0V
Pin8 = HDRV = floating
2. Xray
if active pin6 = B+DRV = flaoating
(from LOT)
pin12 = Vout1 = floating
pin13 = Vout2 = floating
pin16 = CLBL= Hi
a pin3 amplify pin5 and it compare to pin4
inhibit pin6 output
b. pin4 generate the saw_tooth waveform
3.4.5.6 B+ control if pin3 is pulled to
c. pin5 input voltage for the square output waveform
ground by 7507
d. pin6 pwm output to 7603 & 7604 base
to H_deflection.
8. HDRV
7605 Gate
to H_deflection
11.EWDRV east/west control
7505 emitter
V_differential input
12,13 Vout1/Vout2
to 7401 pin 2, 3
14,15 the input sync from
Vsync,Hsync cpu pin 20,21
Vertical blank will be activated = hi
1.pin30 = softstart pll2 = 0V
2.pin26 = pll1 is unlock in searching mode
16. CLBL
3.pin1 = HFLB no exist
4.pin2 = Xray once actived
5.pin10 = Vcc < 9V
Back Forward
46 104S CM23 GSIII Repair Flow Chart
Go to cover page
Hunlock pin is floating while pll1(pin26) is
17. Hunlock
unlock in searching mode
19. IIC sda = hi the initial failure may be these
18. IIC scl = hi of IC 7501,7099,7801,7806
compensate for the V_size
21 EHT_compen.
owing the load variation
22,23,24 pin22 determin the AGC
50Hz< freq. <120Hz
VAGC,VREF ,VCAP pin23,pin24 determin frequency
pin26 determin the
26,27,28,29 pll1 loop filter
30K Hpll1,Hbuf,Href, Hcap pin 27,28,29 H-Freq
working range
1.compare the HFLB(7501 pin1) and control the phase of H-Output(7501 pin8)
30. PLL2
2.softstart
Back Forward