60139ien.pdf part of JVC GY-DV300 JVC GY-DV300 14parts !.part01.rar, DV CAMCORDER text manual preview

Text preview for : 60139ien.pdf part of JVC GY-DV300 DV CAMCORDER

Back to : JVC GY-DV300 14parts !.pa | Home

U

E

DV CAMCORDER

DV CAMCORDER DV CAMKORDER CAMESCOPE DV
INSTRUCTION MANUAL

GY-DV300

GY-DV300

INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS

Thank you for purchasing this JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance. For Customer Use : Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. GY-DV300 Serial No.
LWT0017

This instruction manual is made from 100% recycled paper.

Thank you for purchasing this JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance.

This instruction manual is made from 100% recycled paper.

LWT0018

U
IMPORTANT SAFEGUARDS
1. 2. 3. 4. 5. 6. 7. Read all of these instructions. Save these instructions for later use. All warnings on the product and in the operating instructions should be adhered to. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. Do not use this appliance near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Do not place this appliance on an unstable cart, stand, or table. The appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer, or sold with the appliance. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Slots and openings in the cabinet and the back or bottom are provided for ventilation, and to insure reliable operation of the appliance and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the appliance on a bed, sofa, rug, or other similar surface. This appliance should never be placed near or over a radiator or heat register. This appliance should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided. This appliance should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. For appliance designed to operate from battery power, refer to the operating instructions. This appliance system is equipped with a 3-wire grounding type plug (a plug having a third (grounding) pin). This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding plug. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. Do not allow anything to rest on the power cord. Do not locate this appliance where the cord will be abused by persons walking on it. Follow all warnings and instructions marked on the appliance. Do not overload wall outlets and extension cords as this can result in fire or electric shock. Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance. Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the appliance. c. If the appliance has been exposed to rain or water. d. If the appliance does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to normal operation. e. If the appliance has been dropped or the cabinet has been damaged. f. When the appliance exhibits a distinct change in performance this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Upon completion of any service or repairs to this appliance, ask the service technician to perform routine safety checks to determine that the appliance is in safe operating condition.

E
Thank you for purchasing the JVC GY-DV300 Camcorder. These instructions are for the GY-DV300E. The instructions are given in three languages: English from page E-2 to E-107, German from page G-2 to G-107, French from page F-2 to F-107. This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives. This equipment is designed for professional video appliances and can be used in the following environments: residential area (in houses) or rural area commercial and light industry; e.g. offices or theatres urban outdoors In order to keep the best performance and furthermore for electromagnetic compatibilitiy we recommend to use cables not exceeding the following length:
Port DC IN VIDEO OUT Y/C OUT LINE OUT CH-1CH-2 Cable Exclusive Cable Shielded Cable Exclusive Cable Shielded Cable Lenght 1.9 meters 5 meters 3 meters 3 meters Port EARPHONE DV MIC1 MIC2 Cable Shielded Cable Exclusive Cable Shielded Cable Shielded Cable Lenght 1 meters 4.5 meters 0.3 meters 0.3 meters

8.

9. 10.

Caution : Where there are strong electromagnetic waves or magnetism, for example near a radio or TV transmitter, transformer, motor, etc., the picture and the sound may be disturbed. In such case, please keep the apparatus away from the sources of the disturbance.

11. 12. 13. 14. 15. 16. 17.

18. 19.

2

E-2

U
SAFETY PRECAUTIONS
FOR USA AND CANADA
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

E
SAFETY PRECAUTIONS
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
This unit should be used with 7V DC only. CAUTION: To prevent electric shocks and fire hazards, do NOT use any other power source. NOTE : The rating plate (serial number plate) is on the body. CAUTION To prevent electric shock, do not open the cabinet. No user servicea-ble parts inside. Refer servicing to qualified service personnel.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AUTION :

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This unit should be used with 7V DC only. CAUTION: To prevent electric shocks and fire hazards, do NOT use any other power source.
NOTE: The rating plate (serial number plate) is on the body. CAUTION To prevent electric shock, do not open the cabinet. No user servicea-ble parts inside. Refer servicing to qualified service personnel.

AVERTISSEMENT : POUR EVITER LES RISQUES D'INCENDIE OU D'ELECTROCUTION, NE PAS EXPOSER L'APPAREIL A L'HUMIDITE OU A LA PLUIE.
Ce magnétoscope ne doit être utilisé que sur du courant direct en 7V. ATTENTION : Afin d'eviter tout resque d'incendie ou d'électrocution, ne pas utillser d'autres sources d'alimentation électrique. REMARQUE : La plaque d'identification (numéro de série) se trouve sur le panneau arrière de l'appareil.

INFORMATION FOR USA
INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmfull interfrence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER'S AUTHORITY TO OPERATE THE EQUIPMENT. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS : (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION

AVERTISSEMENT : POUR EVITER LES RISQUES D'INCENDIE OU D'ELECTROCUTION, NE PAS EXPOSER L'APPAREIL A L'HUMIDITE OU A LA PLUIE. Ce magnétoscope ne doit être utilisé que sur du courant direct en 7V. ATTENTION : Afin d'eviter tout resque d'incendie ou d'électrocution, ne pas utillser d'autres sources d'alimentation électrique.
REMARQUE : La plaque d'identification (numéro de série) se trouve sur le panneau arrière de l'appareil.

INFORMATION (FOR CANADA) RENSEIGNEMENT (POUR CANADA)
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la Class B est conforme à la norme NMB-003 du Canada.

3

E-3

For servicing Refer to the service manual page 2-1, "2.1.2 Regarding LP mode"

Thank you for purchasing the DV Camcorder GY-DV300. These instructions are for the GY-DV300.

MAIN FEATURES
Newly developed built-in 12-bit DSP employed for high-quality picture High quality picture with 400% dynamic range Compact, lightweight design DV high-quality digital format The 4:1:1 (U MODEL)/4:2:0 (E MODEL), 8-bit, 25 Mbps component digital signal processing of the format ensures recording and playback with high picture quality. High sound quality thanks to PCM audio Two types of sampling, 16-bit, 48 kHz sampling and 12-bit, 32 kHz sampling, ensure high-quality digital audio. Camera section designed with 3-CCD system for high-quality picture Three 1/3" CCDs with 380,000 (U MODEL)/ 440,000 (E MODEL) effective pixels employed. Digital processing for high quality picture reproduction. Super sensitivity F/11, 2000 lux Enables shooting at normal indoor illumination eliminating the need for extra illumination. LOLUX for 2.65 lux (F1.6) illumination Employment of LOLUX mode ensures +24 dB gain. This is ideal for difficult shooting conditions with almost no illumination. Zebra pattern video level indication on monitor screen Built-in color bar (SMPTE type)(U MODEL)/(EBU type)(E MODEL) Aspect ratio switchable between standard and wide-screen Menu allows screen format setting to be switched between 4:3 format and LETTER BOX-screen (16:9). Time code reader/generator Recording of SMPTE (U MODEL)/EBU(E MODEL)time code possible. Edit search function for convenient recording review Variable scan shutter Eliminates flicker when shooting other screen pictures than NTSC (U MODEL)/PAL (E MODEL), such as computer monitor screens. Copes with the range from 60.6 Hz to 2084.6 Hz (U MODEL)/50.1 Hz to 2067.8 Hz (E MODEL). DV (i. LINK) connector DV connector (4-pin) provided. Enables transfer of digital data to other equipment provided with DV connector. Built-in camera-shake compensation function Built-in 2.5" color LCD display Network connection possible (requires installation of the optional network pack KADV300) This allows audio and video streaming data to be transmitted via LAN card or the data can be recorded on a memory card.

This camcorder is a MiniDV video system format camcorder. Videocassettes that are not marked with the MiniDV symbol cannot be used with this unit.

The following phenomena may occur when tapes recorded on other units (including another GY-DV300) are recorded or played back on this camcorder. · The transient section between scenes recorded on other units and those recorded on this unit may appear disturbed. · Digital noise may appear during playback due to tracking errors. In the case of important recordings, do not record within the first 2 to 3 minutes from the beginning of the tape. Before recording important scenes, be sure to perform a test recording and confirm that both video and audio are recorded correctly. We recommend using the "SP" mode for recording important scenes. Recorded video and audio contents are for private use. Other use may infringe on the rights of copyright holders. JVC cannot assume liabilities that may derive from the impossibility of normal recording or playback of video or audio due to malfunction of the camcorder or the videocassette.

About the LP Mode Recording and playback quality in the LP mode is easily affected by the condition of the tape and the environment of use. Mosaic-like noise may appear in the playback picture and the sound may drop out at times, etc. The picture may also be disturbed at the transient sections between scenes.

4

5

INTRODUCTION
CONTENTS
INTRODUCTION Precautions for Proper Use .............................. 7 Routine and Periodical Maintenance ................ 9 Precautions for Use of Head Cleaning Tape ... 10 Videocassette to be Used ............................... 10 Condensation .................................................. 11 Characteristic CCD Phenomena ..................... 11 CONTROLS, INDICATORS AND CONNECTORS Right Side Section .......................................... 12 Rear Section ................................................... 14 Left Side Section ............................................. 18 Front Section ................................................... 20 Top Section ..................................................... 21 Indications on LCD Screen and Viewfinder Screen ....................................... 22 PREPARATIONS Basic System .................................................. Power Supply Preparation ............................... AC Operation .................................................. Battery Pack Operation ................................... Attaching an External Microphone (optional) .. PREPARATIONS FOR OPERATION Turning the Power ON ..................................... Cassette Loading ............................................ LCD Screen Adjustment ................................. Adjustment the Viewfinder ............................... Setting, Displaying and Recording the Date and Time ....................................... Charging the Built-in Battery ........................... Setting, Displaying and Recording the Time Code ............................................. SETTINGS BEFORE SHOOTING Shooting Mode (AUTO/MANUAL) Selection ... Audio Input Signal Selection ........................... Audio Monitor Selection .................................. Focus Mode Selection ..................................... Angle of View (Zoom In/Zoom Out) ................. Menu Screen Settings ..................................... SHOOTING Basic Recording Operation ............................. Viewing the Recorded Scene (Edit Search) .... If the Unit is Left in Recording-Standby Mode .. Recording the Color Bar ................................. Using the AE Function .................................... 6 MANUAL ADJUSTMENTS Manual Focus Adjustment ............................... Using ND Filter ................................................ Obtaining Natural Tint (White Balance) ........... Manual Iris Adjustment ................................... Manual Shutter Speed Adjustment ................. Manual Gain Adjustment ................................. Displaying Zebra Patterns for Adjustment ....... Manual Adjustment of the Audio Recording Level .......................................... Disabling Operation of the Camera-Shake Compensation Function .............................. Adjusting the Quality of Camera Image .......... PLAYBACK Playback of Tape ............................................. Blank Search ................................................... Adjusting the Playback Sound Volume ........... Outputting CH-3/CH-4 Channel Sound ........... 63 65 66 68 70 72 75 76 78 79

Precautions for Proper Use
Supply voltage Make sure that the power is between 6 V and 12 V DC. If the power voltage is too low, abnormal colour and increased noise may occur. Do not exceed 12 V DC in any case, or the unit could be damaged. Allowable ambient temperature and humidity Be sure to use the unit within the allowable temperature range of 0°C to 40°C and a relative humidity of 30% to 80%. Using the unit at a temperature or humidity outside the allowable ranges could result not only in malfunction but the impact on the CCD elements could be serious as small white spots may be generated. When storing the GY-DV300 for a long time, the storage temperatures should be 20°C to 60°C. Strong electromagnetic waves or magnetism Noise may appear in the picture or audio and/or the colours may be incorrect if the camera is used near a radio or television transmitting antenna, in places where strong electromagnetic waves are generated by transformers, motors, etc., or near devices emitting radio waves, such as transceivers or cellular phones. If a transceiver or cellular telephone is used closed to the GY-DV300 while the camera-shake compensation function is in use, the camera image may flicker due to the influence of emitted electromagnetic waves. Use of wireless microphone near the camera When a wireless microphone or wireless microphone tuner is used near the camera during recording, the tuner could pick up noise. Avoid using or placing the unit in places; · subject to extreme heat or cold; · with excessive dirt or dust; · with high humidity or moisture; · subject to smoke or vapour such as near a cooking stove; · subject to strong vibrations or on an unstable surface. · also do not leave the unit for long hours in a parked car under direct sunlight or near room heating equipment. Protect the unit from being splashed with water (especially when shooting in the rain). Protect the unit from being wet when shooting on a beach. In addition, salt and sand may adhere to the camera body. Be sure to clean the camera after use. Protect the unit against penetration of dust when using it in a place subject to sandy dust. Setup level (U MODEL) The video signal of the unit's video output is not provided with a setup level when shipped from the factory. If you want to turn ON the setup level, please set the SET UP item on the SYSTEM menu screen to ON. Optical performance of lens Due to the optical performance of the lens, color divergence phenomena (magnification chromatic aberration) may occur at the periphery of the image. This is not a camera malfunction. Use the unit in an upright position. If placed on its side, heat release efficiency will deteriorate, adversely affecting the tape transport. Depending on the circumstances, the tape may also be damaged. Vibrations Colours may fail to appear during VCR playback in locations subjected to vibrations. Precautions for transportation Do not drop or hit the unit against a hard object. Remove the videocassette before transporting the unit. Do not insert other objects than a videocassette in the cassette insertion slot. Be sure to close the cassette cover when the unit is not to be used for a long period. 7

32 33 33 34 36

80 81 82 83

EXTERNAL COMPONENTS Connecting a Video Component with DV Connector .............................................. 84 MENU SCREEN MENU Screen Structure ................................. Setting Menu Screens ..................................... Contents of Menu Screens ............................. TOP MENU Screen ..................................... SYSTEM Menu Screen ............................... DISPLAY Menu Screen ............................... CAMERA Menu Screen ............................... OPERATION Menu Screen ......................... CLOCK/TC Menu Screen ............................ VTR Menu Screen .......................................

37 38 39 40 41 44 45

86 88 90 90 91 94 96 98 99 99

47 49 51 52 53 54

TROUBLESHOOTING Alarm Indications and Actions ....................... 100 In case of Difficulty ........................................ 102 OTHERS Displaying the Hour Meter Display ................ 104 Specifications ................................................ 105

57 59 60 61 62

INTRODUCTION

For servicing Refer to the service manual page 2-7, "2.4.3 Cleaning"

Routine and Periodical Maintenance
The GY-DV300 incorporates precision mechanical parts, which will collect dirt, wear out and deteriorate as the unit is used. On the other hand, when the unit has been used for a long period in a normal environment, the heads, drums and tape transport mechanisms also accumulate dirt that is deposited on them. Furthermore, dust which penetrates the inside of the VCR section especially during outdoor use will promote the wear and deterioration of mechanical parts by causing poor contact between tape and heads or failure to maintain the video and audio quality at high levels. To prevent wear and deterioration, clean the mechanical parts using a head cleaning tape as routine maintenance. However, as cleaning with a head cleaning tape alone is not enough for cleaning the entire tape transport mechanism, it is also recommended to apply periodical maintenance (inspection) to prevent troubles that may be caused by the sudden occurrence of failure. As the replacement, adjustment and servicing of parts require advanced skill and equipment, please consult the person in charge of professional video equipment at your nearest JVC-authorized service agent.

Precautions for Proper Use (Cont'd)
Do not set the POWER switch to OFF or remove the power cord during recording or playback. Otherwise the tape may be damaged. When the unit is not in use, be sure to set the POWER switch to OFF in order to reduce power consumption. Cleaning the camera body: Wipe the body with a dry, soft cloth. When it is extremely dirty, soak the cloth in a solution of neutral detergent, wring it out and then wipe. To prevent deformation of the body, etc. and to avoid operation hazards, do not allow volatile liquids such as benzene and thinner to contact the body, and do not wipe it with a cloth soaked in such a liquid. The camera may be unstable for a few seconds immediately after the power is turned on, but this is not a malfunction.

CAUTION
Do not point the lens or viewfinder directly at the sun or other strong light source · Eye damage could result. · If the lens or viewfinder is left pointed at the sun, rays may collect inside the unit and cause damage or a fire. When carrying the camera, be sure to hold the carrying handle. Holding the LCD door, lens or viewfinder may result in damage.

Head Cleaning
To maintain beautiful video and sound, be sure to use a head cleaning tape to clean the head periodically. (Read "Precautions for Use of Head Cleaning Tape" on page 10.) If head cleaning is not performed periodically, a type of mosaic noise called block noise may appear in the picture or sound may be interrupted.

Periodical Maintenance
Contents: Check or replace the following mechanical parts according to the running time.
Running Time Drum assembly (including heads) Head cleaner Tape guides & rollers Rotary encoder Belts & gears Drive parts
Block Noise

500H

1000H 1500H

2000H

Use the optional head cleaning tape M-DV12CL. Do not use other than the designated head cleaning tapes. For instructions on how to use the head cleaning tape and precautions for its use, read "Precautions for Use of Head Cleaning Tape" on page 10. When dirt adheres to the video heads of the GYDV300, the warning message "HEAD CLEANING REQUIRED!" appears on the LCD screen and the viewfinder screen during edit search in the recording mode and during playback.

: Clean, check and adjust. : Clean and check. Replace as required. : Replace.

· The maintenance contents vary depending on the operating environment and method. Therefore, the above data should be considered as a reference. Time management The accumulated running time of the unit can be confirmed with the hour meter display (which shows the accumulated drum running time). For details, see "Displaying the Hour Meter Display" on page 104. For consultations related to the maintenance programming or cost, please contact the person in charge of professional video equipment at your nearest JVC-authorized service agent.

HEAD CLEANING REQUIRED!

8

9

INTRODUCTION

Precautions for Use of Head Cleaning Tape
Use the separately sold head cleaning tape MDV12CL. Adhere to the following precautions when using the head cleaning tape. Note 1) When used in a low humidity environment (10% RH to 30% RH), head cleaning should be conducted at intervals half of those given in the above chart. Note 2) If an ME80 tape is used immediately after head cleaning, the VTR WARNING (HEAD) indicator may remain on. In this case, let the tape run as the indicator will turn off after the tape has run for a while. Note 3) Use the cleaning tape at room temperature (10°C to 35°C). Note 4) The cleaning tape case contains instructions for use of the cleaning tape. However, some of these instructions differ from the contents given in this document. When using the cleaning tape, please follow the instructions of this document. Note 5) Perform head cleaning before using the GY-DV300 in the LP mode.

Condensation
If the unit has been cooled down in a cold place and is then carried to a warm place, the moisture contained in the warm air may adhere to the head drum or tape guides and be cooled into water droplets. This phenomenon is referred to as condensation (dewing). When this occurs, the head drum and tape guides are covered with droplets allowing the tape to stick to them, leading to tape damage. Condensation occurs in the following cases: · When the unit is suddenly moved from a cold place Head drum to a warm place. · When a room heater has just started or when the unit is exposed directly to cold air from an air Videotape conditioner. · When the unit is placed in a very humid place. Do not leave the videocassette inserted when moving the camera under conditions where the temperature environment changes. After moving the unit, do not use until the internal parts have stabilized. When condensation occurs in this unit, the "VTR WARNING (DEW)" appears on the LCD screen and the viewfinder screen.

1. The tape runs for 10 seconds at a time in the
PLAY mode. (The tape stops automatically and the unit enters the STOP MODE.) Set the MODE switch on the unit to "VTR". Press the BAR (f/ w) button after the cleaning tape is fully loaded.

VTR WARNING (DEW)

2. Do not use the tape more than four times at
the most for each cleaning.

3. The cleaning tape can be used approximately
100 times. Use the following chart as a guide for periodical head cleaning.
Operating environment Yardstick for use of cleaning tape Low temperature Room temperature 0°C to 10°C 10°C to 35°C 1 to 2 times every 5 hours High temperature 35°C to 40°C

1 to 2 times 1 to 2 times every 20 to 30 hours every 5 hours

To remedy, leave the unit with the power ON and wait until the WARNING indicator disappears. Prevention of condensation When quickly transporting the GY-DV300 from a cold to a warmer place, first take out the cassette. Then place the GY-DV300 in a plastic bag and seal it before transporting the camera. Leave the GY-DV300 in the sealed plastic bag until the camera has the same temperature as the surroundings. This will prevent condensation.

Videocassette to be Used
Use JVC videocassette tapes marked with MiniDV for this unit. Please use DVM60 or DVM30 type videocassettes. Malfunctions may occur if a DVM80 videocassette is used in the LP mode. When recording in the LP mode, use videocassettes bearing the "LP Mode" mark on the package. The following phenomena may occur when tapes recorded in the LP mode are attempted played back on another set. · Noise may appear in the picture and sound · The sound may fall out and the picture may fail to appear · The tape counter indication may be irregular Please play back a tape that is recorded in the LP mode on the unit on which the tape was recorded. Also, these tapes cannot be played back on digital video units that do not support the LP mode. Videocassettes cannot be used upside down. Avoid storing a videocassette with unevenly wound tape, as this may damage the tape. Rewind it to the beginning before placing a cassette into storage. Store videocassettes in a place with little humidity and good ventilation where mould does not form. After a videocassette tape has been used repeatedly, it becomes unable to maintain full performance due to an increase in noise caused by dropouts, etc. Do not continue to use a dirty or damaged tape, as this will reduce the rotary head life. Videocassette tapes marked MiniDV are provided with a switch on the back for use in preventing accidental erasure. Slide the switch to "SAVE" to protect the required recording in the tape from being overwritten. To record on the tape, slide the switch to "REC". Switch
REC SAVE

Characteristic CCD Phenomena
Smear and Blooming Due to the physical structure of a CCD it is possible to induce vertical streaking (called "smear") when shooting an extremely bright light source. Another effect is the expansion of light around a bright light or object (called "blooming"). The CCD employed in this unit is characterized by inducing very little smear or blooming. Nevertheless, please be careful when shooting a bright light source.
Smear (Vertical pale streaking appearing at high luminous object) High luminous object (Electric light, sunlight, etc.) Blooming (Blurring in highlight)

Moire or Aliasing Shooting stripes or fine patterns may cause a jagged effect or a banding in fine mesh patterns. White dots High temperatures can cause CCD sensor pixels to malfunction with the effect of white dots in the image. This condition is conspicuous especially when gain is applied. This is a characteristic of the charged-couple device (CCD). As far as possible, use the unit under conditions where the temperature of the unit does not increase.

For servicing Refer to the service manual page 1-9, "White blemish detection"

For servicing Refer to the service manual page 2-1, "2.1.2 Regarding LP mode"

Monitor screen

10

11

CONTROLS, INDICATORS AND CONNECTORS Right Side Section
!2 !0
6 [FOCUS PUSH AUTO] Focus push auto button Pressing this button when the MANUAL mode is selected for the focus adjustment engages the forced auto focus mode as long as the button is pressed. When the button is released, the manual mode is restored. When the [FOCUS] switch 5 is set to "AUTO", this button does not work. 7 [CH1/CH2 AUDIO LEVEL] CH-1/CH-2 audio recording level controls Used to adjust the recording level of the CH-1 and CH-2 audio channels. To use these controls to adjust the audio level, set the CH1 AUDIO LEVEL or CH2 AUDIO LEVEL item to MANUAL on the OPERATION menu screen. Rotating clockwise increases the recording level. The recording level meter is displayed on the LCD screen and the viewfinder screen. B Tally lamp This lamp lights up red when the GY-DV300 is in the recording mode. It blinks slowly when the battery pack is exhausted and when there is about 3 minutes or less tape remaining. When the tape has run out, or the VTR enters the warning mode, it blinks quickly. Use the TALLY item on the SYSTEM [2/2] menu screen to select whether or not the lamp should light during recording. ( See page 92.)

u
CH-1 AUDIO LEVEL CH-2

PROFESSINAL

ND FILTER ON OFF

IRIS

FOCUS

AUTO MANU
DV CAMCORDER GY-DV300

PUSH AUTO

OPEN

!1 q wer yt i o

1 FOCUS ring Manual focus ring. Set the FOCUS switch 5 to "MANUAL" before turning this ring to adjust the focus manually. If the FOCUS switch is set to "AUTO", this ring will not work. 2 [ND. FILTER] ND-filter switch Turns the built-in ND-filter ON or OFF. When the shooting conditions are too bright during outdoor shooting, set this switch to "ON". This will adjust the quantity of light to approximately 1/32. When this switch is ON, the "ND" indicator is shown on the LCD screen. ( See page 24.) 3 [IRIS] IRIS adjustment dial Dial for manual adjustment of iris. To allow iris adjustment with this dial, set the IRIS item to MANUAL on the OPERATION menu screen. When the MANUAL mode is selected for the iris adjustment, this dial can be rotated to move the iris from fully opened to fully closed. Rotating the dial upward opens the iris, and rotating it downward closes the iris. 12

When the AUTO mode is selected for the iris adjustment, this dial can be rotated to adjust the iris from +3 steps to 3 steps from the auto iris condition. Rotating the dial upward opens the iris, and rotating it downward closes the iris. (See "OPERATION Menu Screen" on page 98.) 4 [IRIS PUSH AUTO] Iris push auto button Pressing this button when the MANUAL mode is selected for the iris adjustment engages the forced auto iris mode as long as the button is pressed. When the button is released, the manual mode is restored. When the AUTO mode is selected for the iris adjustment, this button does not work. 5 [FOCUS] Focus switch This is used to switch between AUTO and MANUAL focus adjustment. Set this switch to "MANU" when the focus ring 1 should be used to adjust the focus.

8 LCD door This is the door behind which the LCD screen is located. The LCD screen can be viewed when the door is open. This door can be turned to face the LCD screen toward the lens (vertically inverted image) or downward. ( See page 39.) 9 LCD door lock release button Slide the button toward the rear side to open the LCD door. 0 Viewfinder Displays the camera image and the playback picture. The brightness and color saturation of the viewfinder screen can be adjusted on the DISPLAY [2/2] menu screen. The viewfinder can be turned approximately 75 degrees upward. A Viewfinder diopter adjustment knob Knob for adjusting until the viewfinder screen image is clearly visible. Raise the viewfinder to facilitate the adjustment.

13

CONTROLS, INDICATORS AND CONNECTORS

Rear Section
connector. I [GAIN] Sensitivity selector button This button is for manual adjustment of sensitivity. It works when the AE item is set to OFF on the OPERATION menu screen. When the AE (Auto Exposure) function is OFF and this button is pressed, the condition of the current gain setting is shown on the LCD screen or the viewfinder screen for about 3 seconds. In this condition, it possible to set the gain setting of the GY-DV300. Gain is set by rotating the SELECT dial L. Rotating the dial upward moves gain in the plus direction, and rotating it downward moves it in the minus direction. When rotation of the dial stops, the set gain is indicated for about 3 seconds. [The variable range is 3 dB to +18 dB (1 dB step)] Pressing the button for 1 second or more engages the LOLUX mode. J [SHUTTER] Shutter speed selector button This button is for manual adjustment of the shutter speed. It works when the AE item on the OPERATION menu screen is set to OFF. Using the SHUTTER item on the OPERATION menu screen, select the shutter speed mode as STEP or VARIABLE. Set to VARIABLE when shooting computer display screens. When the button is pressed in MANUAL mode, the current shutter speed setting is shown on the LCD screen or the viewfinder screen for about 3 seconds. In this condition, it possible to set the shutter speed of the GY-DV300. The shutter speed is set by rotating the SELECT dial L. When rotation of the dial stops, the set shutter speed is indicated for about 3 seconds. [Variable range (U MODEL) STEP: 1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000 VARIABLE: 1/60.1 to 1/2084.6] [Variable range (E MODEL) STEP: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000 VARIABLE: 1/50.1 to 1/2067.8] K [MENU] Menu button Press this button for 1 second or more to display the MENU setting screen. The MENU setting screen is shown on the LCD screen and the viewfinder screen. When the OUTPUT CHAR. item on the DISPLAY [2/2] menu screen is set to MIX, the MENU setting screen can also be output for display via the VIDEO OUT or Y/C OUT connector. Selections and settings in the menu are performed with the SELECT dial L. The normal screen returns when this button is pressed while the MENU setting screen is displayed. L SELECT dial When gain and shutter adjustment is set to the MANUAL mode, this dial is rotated to set the gain or shutter speed. When the white balance adjustment is set to the MANUAL mode, the white balance setting mode can be selected by rotating this dial. [Variable range: PRESET, MEMORY 1, 2, 3] When the MENU setting screen is displayed, this dial is used to select and set items in the menu. To confirm menu items and set values, press the dial. M [CH-1/CH-2 AUDIO] CH-1/CH-2 audio input selector switch Used to select the audio source input to the CH1/CH-2 channel. Separate inputs can be selected for the CH-1/CH-2 channels. MIC 1 : The sound from the built-in microphone or from the MIC 1 input connector is input. Select the input from the built-in microphone or from the MIC 1 input connector with the MIC1 INPUT SEL item on the SYSTEM [1/2] menu screen. MIC 2 : The sound from the MIC 2 input connector is input. N [MONITOR] Audio monitor selector switch Selects the monitor sound heard from the EARPHONE jack X or the built-in speaker. CH-1 : CH-1 audio signal CH-2 : CH-2 audio signal MIX : Mixed signal consisting of the CH-1 and CH-2 audio signals.

!8 @0 !9
CAM-A GAIN
BAR

POWER OFF MODE CAM-B VTR SHUTTER ON PUSH

!3 !5 !7 !4

MENU
AW

FWD

CH-1 AUDIO CH-2 MIC1 MIC2

REV CH-1

MONITOR
CH-2 MIX

!6

@1 @2 @3

@4

C [POWER] POWER switch Turn the power ON and OFF with this switch. D Battery holder (U MODEL) Mount the provided battery pack BN-V428 here. ( See page 34.) D Battery holder (E MODEL) Mount the optional battery pack BN-V416 or BNV428 here. ( See page 34.) The BN-V416 battery pack cannot be used when the optional Network Pack KA-DV300 is used. E Battery lock release button Press this button to remove the battery pack. F [DC INPUT] DC connector Power input connector for 7 V DC. Accepts the optional AC adapter AA-P30. The power range is 6 V to 12 V. G REC Start/Stop button This button starts and stops recording. When the GY-DV300 is in the shooting mode, pressing this button starts the recording. Pressing the 14

button during a recording engages the recording-pause (standby) mode. H [MODE] Mode selector switch Set in accordance with the operating mode of the GY-DV300. When used in the shooting mode, the switch is set to "CAM-A" or "CAM-B". When used in the VTR playback mode, it is set to "VTR". When set to "CAM-A" or "CAM-B" in the shooting mode, two separate sets of setting values for recording can be set by means of the menu screens. "CAM-A" : In this position, shooting takes place in accordance with the conditions set for "CAM-A" on the menu screen. "CAM-B" : In this position, shooting takes place in accordance with the conditions set for "CAM-B" on the menu screen. "VTR" : Set to this position when performing VTR playback. Also set to this position to record the video signal input from the DV

15

CONTROLS, INDICATORS AND CONNECTORS

Rear Section (cont'd)
Pressing this button simultaneously with the REV button R during stop in the VTR playback mode initiates the blank search mode (for locating the end point of recordings).

LCD door storage compartment

#0 @9 @6 @5

R [REV] REVERSE/REW button Pressing this button in the shooting mode engages playback in reverse direction at normal speed for as long as the button is pressed. When the button is released, the recording-standby mode is engaged. Pressing this button in the VTR playback mode during stop or fast forward operation initiates the rewind mode. Pressing this button during playback, still picture playback, or forward search initiates reverse search. S LCD monitor screen Shows a color camera image or the VTR playback picture. It is also used for displaying the following: · Menu setting screens · Characters showing the whether the GYDV300 is set to shooting mode or VTR playback mode · Date and time and time code · Audio level meter · Warning indications, etc. For details, see page 22. · The angle of the LCD screen can be rotated to make the LCD screen face toward the lens or downward. · The brightness and color saturation can be adjusted and set on the DISPLAY [1/2] menu screen. T Built-in speaker Outputs the VTR playback sound. The playback sound level is adjusted with the ZOOM/Playback sound level adjustment lever a. The monitor sound is not output in the shooting mode. The audio from the loudspeaker is not output when an earphone is plugged into the EARPHONE jack X. ( See page 82.)

@7 @8

O [BAR] Color bar/Playback & still button Pressing this button in the shooting mode switches the setting between color bar output and camera image output. Pressing this button in the VTR playback mode starts playback. Pressing this button during playback engages the playback mode. Pressing this button during playback engages the still picture mode. P [AW] White balance/Stop button Used when white balance adjustment is performed in the shooting mode. To use this button for white balance adjustment, the WHITE BALANCE item on the OPERATION menu screen should be set to PUSH AUTO. When this button is pressed, the current white balance setting mode is displayed for about 3 seconds on the LCD screen or the viewfinder screen after which white balance adjustment of the GY-DV300 becomes possible. The white balance adjustment setting mode is selected by rotating the SELECT dial L. When rotation of the dial stops, the selected 16

setting mode is displayed for about 3 seconds. When the button is then pressed for 1 second or more, the white balance adjustment starts. [Variable range: PRESET, MEMORY 1, 2, 3] Memo: The PRESET mode is fixed at 3200 K (colour temperature). Even if the AW button is pressed, white balance adjustment is not performed. Pressing this button in the VTR playback mode engages the Stop mode. Q [FWD] FORWARD/FF button Pressing this button in the shooting mode engages playback in forward direction at normal speed for as long as the button is pressed. When the button is released, the recording-standby mode is engaged. Pressing this button in the VTR playback mode during stop or rewind operation initiates the fast forward mode. Pressing this button during playback, still picture playback, or reverse search initiates forward search mode.

17

CONTROLS, INDICATORS AND CONNECTORS

Left Side Section
#7
The playback sound from the built-in speaker is not output when an earphone is plugged into this jack. Y [DV] DV connector (U MODEL) Using a DV cable (optional), a digital video component with DV connector can be connected here. To record DV signals (IEEE1394 signals) from this connector, the MODE switch H should be set to "VTR". Y [DV] DV connector (E MODEL) Using a DV cable (optional), a digital video component with DV connector can be connected here. This connector is used for output of the DV signal or input the VCR contorl signal from the digital video component with DV connector. The use this connector, set the MODE switch H to "VTR". Memo: The GY-DV300 is not capable of recording DV signals (IEEE1394 signals). Z Cassette cover Sliding the EJECT switch located on the top section opens this cover to allow insertion or removal of the videocassette. The cover locks into place when it is closed after the cassette holder has been properly locked. ( See page 38.) Memo: · When inserting a cassette, push the "PUSH HERE" section on the cassette holder to lock the cassette holder correctly, and then close the cassette cover. · To prevent foreign matter from penetrating into the interior of the GY-DV300, never leave the unit with this cover left open. · The GY-DV300 does not function if the cassette cover is not closed. [ Microphone holder attachment base Use for attaching an optional microphone holder. Attach the optional microphone holder KA-A33 here. ( See page 36.)

MIC 1 IN

MIC 2 IN

#6

#2 #5 #4 #3 #1

U [VIDEO OUT] Video output connector (RCA) Output connector for composite video signal. Outputs the input video signal and playback picture. When the OUTPUT CHAR. item on the DISPLAY [2/2] menu screen is set to MIX, onscreen-indicators like those shown on the LCD monitor screen can be output (black and white display). When the SETUP item on the SYSTEM [2/2] menu screen is set to ON, signals with setup information can be output. (black and white display) (U MODEL) V [Y/C OUT] Y/C video output connector (4-pin) Separate YC video signal output connector. Outputs the input video signal and playback picture. When the OUTPUT CHAR. item on the DISPLAY [2/2] menu screen is set to MIX, onscreen-indicators like those shown on the LCD monitor screen can be output (black and white display).

When the SETUP item on the SYSTEM [2/2] menu screen is set to ON, signals with setup information can be output. (black and white display) (U MODEL) When the ASPECT item is set to LETTER on the SYSTEM [2/2] menu screen, an ID signal for identifying the wide-screen aspect is output. W [CH-1/CH-2 LINE OUT] CH-1/CH-2 audio output connector (RCA) Output connector for audio signal. In the shooting mode the input audio signal is output. In the VTR mode the playback sound is output. X [EARPHONE] Earphone jack This is a jack for connecting an earphone for monitoring the sound. Plug in an earphone or headphone with a 3.5 mm diameter plug. Monaural sound is output. Select the output sound with the MONITOR switch N. The volume of the monitor sound in the shooting mode is set with the EARPHONE LEVEL item on the TOP MENU screen.

18

EARPHONE

LINE CH-2 OUT CH-1 VIDEO OUT

DV

Y/C OUT

19

CONTROLS, INDICATORS AND CONNECTORS

Front Section

CONTROLS, INDICATORS AND CONNECTORS

Top Section
$3

]

\
W T
START/ STOP

EJECT

`

W

VOLUME

T

$1

$2

$4

\ Built-in microphone Built-in monaural microphone. To use this microphone, set the MIC1 INPUT SEL item to INT on the SYSTEM [1/2] menu screen. ] [MIC 1] Microphone 1 input connector (XLR3P) Connect an external microphone to this connector. Monaural signals are recorded. To use the microphone connected to this connector, set the MIC1 INPUT SEL item to XLR on the SYSTEM [1/2] menu screen. To use a microphone requiring +48 V power supply (phantom microphone), set the +48V MIC1 item on the SYSTEM [1/2] menu screen to ON. This connector will then supply +48 V DC current. When using a microphone other than a phantom microphone, set the +48V MIC1 item to OFF.

` [MIC 2] Microphone 2 input connector (XLR3P) Connect an external microphone to this connector. Monaural signals are recorded. To use a microphone requiring +48 V power supply (phantom microphone), set the +48V MIC2 item on the SYSTEM [1/2] menu screen to ON. This connector will then supply +48 V DC current. When using a microphone other than a phantom microphone, set the +48V MIC2 item to OFF. Memo: · The audio input channel is selected with the CH-1/CH-2 audio input selector switch M. · To reduce the wind noise of the microphone, set the WIND CUT MIC1/MIC2 item on the SYSTEM [1/2] menu screen to ON.

a ZOOM/Playback sound level adjustment lever This works as the zoom lever in the shooting mode. Pressing the lever in the T direction narrows the lens angle perspective for telephoto shots. Pressing it in the W direction increases the angle of the lens for a wider shooting angle. The harder the lever is pressed, the quicker the zoom action. In the VTR playback mode, this lever is used for adjusting the playback sound level. Pressing the lever in the + direction increases the volume level, and pressing in the - direction decreases the level. b [EJECT] Eject switch Slide to the side when inserting or ejecting the videocassette. Sliding this button and then opening the cassette cover will eject the cassette.

c [ZOOM] Zoom lever Lever for zoom operation from the handle top section. In the shooting mode, pressing this lever in the T direction narrows the lens angle perspective for telephoto shots. Pressing it in the W direction increases the angle of the lens for a wider shooting angle. The zoom speed of this zoom lever is selected with the HANDLE ZOOM item on the SYSTEM [2/2] menu screen. d [START/STOP] REC START/STOP button Button for start and stop of recording from the handle top section. When the GY-DV300 is in the shooting mode, pressing this button starts the recording. Pressing the button during a recording engages the recording-standby mode.

20

21

CONTROLS, INDICATORS AND CONNECTORS

Indications on LCD Screen and Viewfinder Screen
Normal display in the shooting mode

In addition to the E-E picture and the playback picture, the following indications are displayed on the LCD screen and the viewfinder screen. Status screens (screens for use in checking the current camera settings) Event indications Alarm indications Menu setting screens Auto white balance operation indicator When the LCD screen is used, the above indicators are not shown on the viewfinder screen. When the LCD screen is faced toward the viewfinder screen side and the LCD door is closed, the above indictors appear on the viewfinder screen. Status Screens The contents of the status screens differ in the camera shooting mode and in the VTR playback mode. Also, the items displayed on the status screen differ with the direction that the LCD screen is facing, i.e., toward the viewfinder (normal display) or toward the lens (vertically inverted display). Normal display in the shooting mode Vertically inverted display in the shooting mode Battery symbol

q

w e r t y

No. 1

Item

Contents

Zoom ratio (Characters, Displayed during zoom operation. The characters indicate the widenumeric value) angle (W) and telephoto (T) zoom positions. The numeric value indicates the approximate zoom ratio. Time code display Shows the time code (hours, minutes, seconds, frames). Whether this should be displayed can be selected by setting the TIME CODE item on the DISPLAY [2/2] menu screen. Shows the recording speed at the time of the recording. SP : Standard Play mode LP : Long Play mode When the remaining tape indication is OFF, this indication is shown at the 4 position.

2

VTR operation symbol (Recording or pause) For a part of the status indicators it is possible to select whether or not the item should be displayed by making a selection on the DISPLAY [2/2] menu screen. In relation to the normal display, the vertically inverted display is reversed left to right, and only the battery symbol and the recording symbol/pause symbol are displayed. When the LCD screen is faced toward the lens side and the LCD door is closed, the normal display will be seen.

3

Recording time mode indication

4

Remaining tape time indication

Memo: After-images will increase on the LCD screen when used under cold circumstances.

Indicates the remaining tape amount (minutes) in 1-minute steps. Whether this indication should be ON or OFF can be selected by setting the TAPE REMAIN item on the DISPLAY [2/2] menu screen. * The indication may not appear when a new tape is loaded, after the tape runs, the indication appears. The remaining battery power is indicated by four different indicators.

5

Remaining battery power indication

Fully charged battery 6 Camera-shake compensation on indication

Blinking indicator (no remaining battery power)

Displayed when the camera-shake compensation function is on (OIS item on the OPERATION menu screen is set to ON). 23

22

CONTROLS, INDICATORS AND CONNECTORS

Indications on LCD Screen and Viewfinder Screen (Cont'd)
No. A Item Shooting mode indication Contents Indicates whether the shooting mode is AUTO or MANUAL. Å: Displayed when the shooting mode is AUTO (when the MODE item is set to AUTO on the TOP MENU screen). ~: Displayed when the shooting mode is MANUAL (when the MODE item is set to MANUAL on the TOP MENU screen). ND: Displayed when the ND filter switch is set to ON. Indicates the F-value of the lens in the manual iris adjustment mode (when the IRIS item is set to MANUAL on the OPERATION menu screen). The indications are: F1.6, F2, F2.8, F4, F5.6, F8, F11, F16. CLOSE 3 ~ ±0 ~ +3: Indicates the compensation value set with the iris adjustment dial in the auto iris mode. M: Displayed in the manual iris adjustment mode. STBY: REC: ED.FWD: ED.REV: STOP: EJECT: : Recording-standby mode During recording During playback in forward direction During playback in reverse direction Tape protect mode During cassette ejection Tape is not loaded

!2 !3 !4 !5
No. 7 8 Item Manual focus indication Manual shutter mode indication

u i o !0 !1

B C

Filter indication Iris F-value indication

D

Iris compensation value indication VTR mode indicators

!6

!7

!8
Contents

!9

E

MF: Displayed when manual focusing is enabled (when the FOCUS switch is set to MANUAL). Displayed in the manual shutter mode (when the AE item is set to OFF on the OPERATION menu screen). This indication is not shown when the shooting mode is AUTO or the AE item is set to ON. It is not shown when the shutter is NORMAL (1/60 (U MODEL)/1/50 (E MODEL)) or gain is set to ALC. Indicated in the manual gain setting mode (when the AE item is set to OFF on the OPERATION menu screen). 6 dB: The gain value is indicated for anything but 0 dB, LOLUX, or ALC. L: Displayed in LOLUX mode. The indication is not shown when the gain setting is 0 dB or ALC. It is not shown when the shooting mode is AUTO, or the AE item is set to ON. Displayed when manual white balance adjustment is enabled (when the WHITE BALANCE item is set to PUSH AUTO on the OPERATION menu screen). Indicates the white balance setting mode. WBP: White Balance Preset mode (fixed at a colour temperature of 3200 K. Manual white balance adjustment is inhibited.) WB1: White Balance memory 1 mode WB2: White Balance memory 2 mode WB3: White Balance memory 3 mode When WB1, WB2 or WB3 is indicated, manual white balance adjustment is enabled. The result of the white balance adjustment is retained in the indicated memory. It is not shown when the shooting mode is AUTO, or when the WHITE BALANCE item is set to AUTO. S: F Fade indication

Displayed when the fade function is ON (when the FADER item is set to BLACK on the SYSTEM [2/2] menu screen). BK : Displayed when the FADER item is set to BLACK. (Fade-in and fade-out from black screen.) 32K: Displayed when the AUDIO MODE item is set to 32K on the SYSTEM [1/2] menu screen. (Audio is recorded with 12-bit, 32 kHz sampling.) 48K: Displayed when the AUDIO MODE item is set to 48K on the SYSTEM [1/2] menu screen. (Audio is recorded with 16-bit, 48 kHz sampling.) Indicates the audio levels of CH-1, CH-2. These meters are not shown when the AUDIO LEVEL item is set to OFF on the DISPLAY [2/2] menu screen. Shows the date and time. The indication is enabled/disabled by selecting the TIME/DATE item on the DISPLAY [2/2] menu screen. The display style is selected by setting the DISP STYLE item. When the date and time are not set, the indication will be as follows. // ::

G

9

Manual gain mode indication

Audio sampling frequency indication

H

Audio level meter display Date and time indication

0

Manual white balance mode indication

I

24

25

CONTROLS, INDICATORS AND CONNECTORS

Indications on LCD Screen and Viewfinder Screen (Cont'd)
VTR playback mode/IEEE1394 recording mode status indications Remaining battery power indication The remaining battery power is indicated by four different indicators. : Fully charged battery

Vertically inverted display indications in the shooting mode

q
VOL.

w e r t

: Remaining battery power is low : No remaining battery power (blinking) VTR operation mode indication symbol: During recording w symbol: In recording-standby mode

P L AY

DV

No. 1 2

Item

Contents

Audio playback volume Displayed in the VTR mode. Characters indicate the high and low of indication the playback volume. Time code indication The recorded time code data (hours, minutes, seconds, frames) are shown here in the playback mode. The indication is turned ON/OFF by setting the TIME CODE item on the DISPLAY [2/2] menu screen.

3

Recording/playback The mode in which the tape was recorded is displayed during playback. speed mode indication SP: Standard Play mode LP: Long Play mode When the remaining tape time indication is set to OFF, this indication is shown at the position indicated by 4. Remaining tape time indication Indicates the remaining tape time in 1-minute steps. The indication is turned ON/OFF by setting the TAPE REMAIN item on the DISPLAY [2/2] menu screen. * The indication may not appear when a new tape is loaded, after the tape runs, the indication appears. The remaining battery power is indicated by four different indicators.

4

5

Remaining battery power indication

Fully charged battery

Blinking indicator (no remaining battery power)

26

27

CONTROLS, INDICATORS AND CONNECTORS

Indications on LCD Screen and Viewfinder Screen (Cont'd)
Event Indications
When the gain and shutter speed are changed manually, the set condition is displayed for about 3 seconds at the time the change is made.

VOL.

Event display area

Event display area

PLAY

DV

y

u
(U MODEL)

i

o

!0

No. 6 7

Item VTR mode indication DV signal indication (U MODEL)

Contents Indicates status of VTR operation. (STOP, PLAY, FF, REW, EJECT, STBY, FWD, REV, BSRH) DV : Displayed when IEEE1394 signal is recorded from the DV connector. The audio sampling frequency by which the recording was made is displayed during playback. (32K, 48K, 44.1K) The playback audio level meters are displayed during playback. These are not shown when the AUDIO LEVEL item is set to OFF on the DISPLAY [2/2] menu screen. Recorded data is show during playback, fast forward and rewind operations. During recording, the data from the DV connector is shown. The current data is shown in the stop mode. The indication is enabled/disabled by selecting the TIME/DATE item on the DISPLAY [2/2] menu screen. The display style is selected by setting the DISP STYLE item. When the date and time are not set, the indication will be as follows. // :: Set Condition When the gain value is changed When the LOLUX gain mode is selected When the shutter speed is changed Contents of Indication GAIN 3 dB to 18 dB (1 step) LOLUX SHUTTER 1/100, 1/250. 1/500, 1/1000, 1/2000 (U MODEL) 1/120, 1/250. 1/500, 1/1000, 1/2000 (E MODEL) When the variable shutter speed is changed V.SHUTTER 1/60.1 - 1/2084.6 (U MODEL) 1/50.1 - 1/2067.8 (E MODEL)

8 9

Audio sampling frequency indication Audio level meters display Date and time indication

0

When the shutter is NORMAL (shutter speed: 1/60) SHUTTER NORMAL

28

29

CONTROLS, INDICATORS AND CONNECTORS

Indications on LCD Screen and Viewfinder Screen (Cont'd)
MENU Setting Screen
MEN U MODE MA NU AL 10 E A R PHON E L E V E L S Y S T EM S E T . . D I S P L AY SE T . . CAME RA S E T [ C A M - A ] . . OPE R AT I ON [ C AM - A ] . . C L OC K / T C . . MENU A L L R E SE T C ANC E L EX I T

Alarm indications
Alarm indications are displayed under the following circumstances. The warning messages are shown blinking. · When remaining battery power or remaining tape is low. · Improper operation attempted. · Abnormality generated in the GY-DV300.

Used for making a variety of settings. See "MENU Setting Screen" on page 86.

Warning indication area

Warning indication area

Auto White Balance Indication
AUTO WHITE and the result of the operation are displayed when the auto white balance adjustment is performed. See "Auto White Balance Adjustment" on page 66.

AUTO WH I TE OPERATION

Warning Indication TAPE NEAR END TAPE END TAPE BEGIN LOW VOLTAGE CLOSE CASSETTE COVER! NO TAPE REC INHIBIT 1394 INHIBIT (U MODEL) COPY INHIBIT CASSETTE COVER OPEND! CASS.CARRIAGE UNLOCK VTR WARNING [DEW] HEAD CLEANING REQUIRED! VTR WARNING (HARD) VTR WARNING (TAPE) 30

Contents Displayed when the remaining tape is 3 minutes or less in the shooting mode. It is not shown in the playback mode. Displayed when the tape has run out. Displayed when the tape is at the beginning position. Displayed when remaining battery power becomes low. Displayed when operation is attempted while the cassette cover is open. Displayed when no videocassette is inserted and the VTR trigger button is pressed. Displayed when an unrecordable videocassette (the switch on the back of the cassette is set to "SAVE") is loaded. Displayed if an attempt to record is made when no DV signal is input. Displayed when attempt to record a copy-guard protected signal is made. Displayed when the cassette cover was opened during recording. Displayed when the cassette cover is closed but the cassette holder is not locked. Displayed when condensation occurs in the unit. Displayed in case of video head clogging. Lights when abnormality occurs in the unit. Displayed when the tape is cut. 31

PREPARATIONS Basic System

U E PREPARATIONS
4P IEEE1394 CABLE 4P MICROPHONE MV-P615 4P IEEE1394 CABLE 6P

Basic System

MICROPHONE MV-P615

MIC HOLDER

MIC HOLDER

4P

IEEE1394 CABLE

4P

4P IEEE1394 CABLE 6P

VIDEO LIGHT

VIDEO LIGHT

NETWORK PACK KA-DV300

PC

NETWORK PACK KA-DV300

PC

DV CAMCORDER AC TELE CONVERSION LENS
ND FILTER ON OFF CH-1 AUDIO LEVEL CH-2

DV CAMCORDER AC ADAPTER/BATTERY CHARGER AA-P30
OPEN

PROFESSINAL

TELE CONVERSION LENS
ND FILTER ON OFF

CH-1 AUDIO LEVEL

CH-2

PROFESSINAL

IRIS

FOCUS

AC AC ADAPTER/ BATTERY CHARGER AA-P30
OPEN

IRIS

FOCUS

AUTO MANU
DV CAMCORDER GY-DV300

AUTO MANU
DV CAMCORDER GY-DV300

PUSH AUTO

PUSH AUTO

WIDE CONVERSION LENS

RECHARGEABLE BATTERY PACK BN-V428 ACCESSORY KIT

WIDE CONVERSION LENS

RECHARGEABLE BATTERY PACK BN-V416

BATTERY PACK (Large-capacity) BN-V428

TRIPOD

TRIPOD

32

E-32

PREPARATIONS

Power Supply Preparation

PREPARATIONS

Power Supply Preparation (cont'd)

The GY-DV300 is operable with AC power supply or battery pack.

Battery Pack Operation
Use the provided battery pack BN-V428 for battery pack operation. (U MODEL) Use the optional battery pack BN-V416 or BN-V428 for battery pack operation. (E MODEL) The BN-V416 battery pack cannot be used when the optional Network Pack KA-DV300 is used. (E MODEL)

AC Operation
Use the provided (U MODEL)/optional (E MODEL) AC Adapter/Charger AA-P30 as the AC power supply. The DC INPUT connector on the GY-DV300 accepts power voltage in the range of DC 6V to DC 12V. POWER lamp POWER switch To AC outlet

Charging the Battery Pack
AC outlet AC cord Before use the battery pack should be charged using the provided AC Adapter/Charger AA-P30.

1. Plug the AC cable of the AC Adapter/Charger
into an AC outlet. The POWER lamp illuminates.

2. While pushing the battery pack down, slide it
Battery pack CHARGE lamp 1 POWER lamp CHARGE lamp 2 AA-P30 in the direction of the arrow to mount it on the AC Adapter/Charger. Charging starts, and the CHARGE lamp blinks green. It changes to light steadily when charging is completed. When charging is completed, remove the battery by sliding it in the opposite direction of the mounting direction. * For details, see the instruction manual for the AA-P30.

AC cord

3.

Attaching the Battery Pack on the GY-DV300
DC INPUT connector DC cable Set the POWER switch on the GY-DV300 to OFF. If a battery pack is attached to the unit, detach the battery pack. AA-P30 DC OUTPUT connector If the DC cable is connected to the GY-DC300, unplug the cable.

1. Hold the battery pack with the connector side
facing the GY-DC300.

2. While pressing the battery pack against the