Text preview for : UCC [radial thru-hole] SMG series.pdf part of Chemi-con UCC [radial thru-hole] SMG series . Electronic Components Datasheets Passive components capacitors Chemi-con UCC [radial thru-hole] SMG series.pdf
Back to : UCC [radial thru-hole] SM | Home
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS Downsized, 85
Endurance : 2,000 hours at 85 SMQ
Solvent resistant type except 315 to 450Vdc Downsized
(see PRECAUTIONS AND GUIDELINES) SMG
RoHS Compliant
SPECIFICATIONS
Items Characteristics
Category
Temperature Range -40 to +85 (6.3 to 400Vdc) -25 to +85 (450Vdc)
Rated Voltage Range 6.3 to 450Vdc
Capacitance Tolerance 20% (M) (at 20 , 120Hz)
Leakage Current 6.3 to 100Vdc 160 to 450Vdc
18 I=0.03CV or 4 A, whichever is greater. CV Time After 1minute After 5minute
CV 1,000 I=0.1CV+40 max. I=0.03CV+15 max.
CV>1,000 I=0.04CV+100 max. I=0.02CV+25 max.
(at 20 after 1 minute) (at 20 )
20 I=0.03CV (at 20 after 3 minutes)
Where, I : Max. leakage current ( A), C : Nominal capacitance ( F), V : Rated voltage (V)
Dissipation Factor Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 315 to 400V 450V
(tan ) 18 0.34 0.24 0.20 0.16 0.14 0.12 0.09 0.08 0.20 0.24 0.24
tan (Max.)
20 0.28 0.24 0.20 0.16 0.14 0.12 0.09 0.08 0.15 0.15 0.20
When nominal capacitance exceeds 1,000 F, add 0.02 to the value above for each 1,000 F increase. (at 20 , 120Hz)
Low Temperature Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 315 to 400V 450V
Characteristics Z(-25 )/Z(+20 ) 18 5 4 3 2 2 2 2 2 3 6 6
(Max. Impedance Ratio)
20 5 4 3 2 2 2 2 2 4 6 6
Z(-40 )/Z(+20 ) 18 12 10 8 5 4 3 3 3 4 6 - (at 120Hz)
Endurance The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 2,000 hours
at 85 .
Capacitance change 20% of the initial value
D.F. (tan ) 200% of the initial specified value
Leakage current The initial specified value
Shelf Life The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 1,000 hours at 85 without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage 6.3 to 100Vdc 160 to 450Vdc
Capacitance change 20% of the initial value 20% of the initial value
D.F. (tan ) 200% of the initial specified value 200% of the initial specified value
Leakage current The initial specified value 500% of the initial specified value
DIMENSIONS [mm]
Terminal Code : E
5 to 18 Sleeve (PET : Black)
F 0.5
F 0.5
d
D'
Vent L' 15min. 4min. ( 5 to 10) ( 12.5 to 18)
(except 5) Gas escape end seal
Sleeve (PET : Black)
F 0.5
20
d
D 5 6.3 8 10 12.5 16 18 20 22
d 0.5 0.5 0.6 0.6 0.6 0.8 0.8 1.0 1.0
D'
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5 10.0 10.0
D' D+0.5max. D+0.5max.
L' L+1.5max. L+2.0max.
Vent L' 15min. 4min.
PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E S MG A A A E A A A A A M A A A N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 1.0 F:1R0,10 F:100,100 F:101)
Lead forming