Sony_DV-PS560_Align.pdf part of Sony DV-PS560 Sony_DV-PS560_Align.rar, Sony_DV-PS560

Text preview for : Sony_DV-PS560_Align.pdf part of Sony DV-PS560 Sony_DV-PS560_Align

Back to : Sony_DV-PS560_Align.rar | Home

DVP-S336/S345/S360/S365/S560D/S570D/S745D SECTION 6 TEST MODE
6-1. GENERAL DESCRIPTION
### Syscon Diagnosis ### Diag All Check No. 2 Version 2-3. ROM Check Sum Check Sum = xxxx

The Test Mode allows you to make diagnosis and adjustment easily using the remote commander and monitor TV. The instructions, diagnostic results, etc. are given on the on-screen display (OSD).

6-2.

STARTING TEST MODE

Press [TITLE], [CLEAR], [POWER] buttons on the remote commander in this order with the power of main unit in OFF status, and the Test Mode starts, then the menu shown below will be displayed on the TV screen. At the bottom of menu screen, the model name and revision number are displayed. To execute each function, select the desired menu and press its number on the remote commander. To exit from the Test Mode, press the POWER button.
Test Mode Menu 0. 1. 2. 3. 4. 5. 6. Syscon Diagnosis Drive Auto Adjustment Drive Manual Operation Mecha Aging Emergency History Version Information Video Level Adjustment Exit: Power Key

Press NEXT Key to Continue Press PREV Key to Repeat _

For the ROM Check, the check sum calculated by the Syscon is output, and therefore you must compare it with the specified value for confirmation. Following the message, press [NEXT] key to go to the next item, or [PREV] key to repeat the same check again. To quit the diagnosis and return to the Check Menu screen, press [STOP] or [ENTER] key. If an error occurred, the diagnosis is suspended and the error code is displayed as shown below.
### Syscon Diagnosis ###

_ Model : DPX13xxxx Revision : 1.xxxx

6-3.

SYSCON DIAGNOSIS

3-2. EEPROM Check Error 03: EEPROM Write/Reed N Address : 00000001 Write Data : 2492 Read Data : 2490 Press NEXT Key to Continue Press PREV Key to Repeat _

The same contents as board detail check by serial interface can be checked from the remote commander. On the Test Mode Menu screen, press [0] key on the remote commander, and the following check menu will be displayed.
### Syscon Diagnosis ### Check Menu Quit All Version Peripheral Servo Supply AV Decoder Video Audio

Press [STOP] key to quit the diagnosis, or [PREV] key to repeat the same item where an error occurred, or [NEXT] key to continue the check from the item next to faulty item. Subnemu Selecting 2 and subsequent items calls the submenu screen of each item. For example, if "5. Supply" is selected, the following submenu will be displayed.
### Syscon Diagnosis ### Check Menu No. 5 Supply Quit All ARP Register Check ARP to RAM Data Bus ARP to RAM Address Bus ARP RAM Check

0. 1. 2. 3. 4. 5. 6. 7. 8. _

0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.

0. 1. 2. 3. 4. 5. _

1. All
All items continuous check This menu checks all diagnostic items continuously. Normally, all items are checked successively one after another automatically unless an error is found, but at a certain item that requires judgment through a visual check to the result, the following screen is displayed for the key entry.

0. Quit
Quit the submenu and return to the main menu.

6-1

1. All
All submenu items continuous check This menu checks 2 and subsequent items successively. At the item where visual check is required for judgment or an error occurred, the checking is suspended and the message is output for key entry. Normally, all items are checked successively one after another automatically unless an error is found. Selecting 2 and subsequent items executes respective menus and outputs the results. For the contents of each submenu, see "Check Items List". General Description of Checking Method

3. Peripheral
(3-2) EEPROM Check Data write read, and accord check Error 03: EEPROM write/read discord Before writing, the data are saved, then after checking, they are written to restore the contents of EEPROM. (3-3) Gate Array Check Data write read, and accord check Error 02: Gate array write/read discord (3-4) NAND Flash Check Data clear write read, and accord check This check is conducted to the DVP-S570D/S745D only. Error 04: Clear error 05: Write error 06: Read data discord 21: Faulty blocks exceed 10 The data clear, write, read, and check are executed to the block 0 of Flash memory (IC802). In case of a faulty block, its address is displayed.

2. Version
(2-2) Revision ROM revision number is displayed. Error: Not detected. The revision number defined in the source file of ROM (IC104) is displayed with four digits. (2-3) ROM Check Sum Check sum is calculated. Error: Not detected. The data are added of ROM (IC104) and the result is displayed with 4-digit hexadecimal number. Error is not detected. Compare the result with the specified value. (2-4) Model Type Model code is displayed. Error: Not detected. The model code is displayed with 2-digit hexadecimal number. Model Type DVP-S336 (KR) DVP-S345 (CH) DVP-S345 (HK, SP) DVP-S360 (US, CND, E) DVP-S365 (PX) DVP-S560D (US, CND, E) DVP-S570D (US, CND) DVP-S745D (HK, SP, KR) DVP-S745D (CH) � Abbreviation CH : Chinese CND: Canadian HK : Hong Kong KR : Korea SP : Singapore (2-5) Region Region code is displayed. Error: Not detected. The region code determined from the model code is displayed. 0 0 0 0 0 1 2 2 2 7 6 7 0 0 0 0 3 6

4. Servo
(4-2) Servo DSP Check Data write read, and accord check Error 12: Read data discord (4-3) DSP Driver Test Test signal data DSP Driver Error: Not detected.

5. Supply
Caution: Do not conduct this check with a mechanical deck connected. An access is made to the stream supply and servo control IC (IC302) and external RAM (IC303) using check data. If mechanical deck is connected, the motor and optics could be damaged. This check is also executed by the "All" menu item. Supplement: How to disconnect mechanical deck Disconnect flexible flat cables connected to the CN201 and CN202 of MB-86 board. Also, disconnect flat cable from the CN401. (5-2) ARP Register Check Data write read, and accord check Error 08: ARP register write, and read data discord (5-3) ARP to RAM Data Bus Data write read, and accord check Error 09: ARP RAM data bus error Data 0x0001 to 0x8000 where one bit each is set to 1 are written to the address 0 of RAM (IC303) connected to the ARP (IC302) through the bus, then they are read and checked. In case of discord, written bit pattern and read data are displayed. If data where multiple bits are 1 are read, the bits concerned may touch each other. Further, if data where certain bit is always 1 or 0 regardless of written data, the line could be disconnected or shorted.

6-2

(5-4) ARP to RAM Address Bus Data write other address read discord check Error 10: ARP RAM address bus error Caution: Address and data display in case of an error is different from the display of other diagnosis (described later). Before starting the test, all addresses of RAM (IC303) are cleared to 0x0000. First, 0xA55A is written to the address 0x00000, and the address data are read and checked from addresses 0x00001 to 0x80000 while shifting 1 bit each. Next, the data at that address is cleared, and it is written to the address 0x00001, and read and checked in the same manner. This check is repeated up to the address 0x80000 while shifting the address data by 1 bit each. If data other than 0 is read at the addresses except written address, an error is given because all addresses were already cleared to 0. In this check, the error display pattern is different from that of other diagnosis; read data, written address, and read address are displayed in this order. However, the message uses same template, and accordingly exchange Address and Data when reading. The following display, for example,
### Syscon Diagnosis ###

6. AV Decoder
(6-2) 1930 RAM Data write read, and accord check Error 13: AVD RAM read data discord The program code data stored in ROM (IC104) are copied to all areas of RAM (IC504, IC505) connected to the AVD (IC502) through the bus, then they are read and checked if they accord. Further, the same test is conducted once again with the data where all bits are inverted between 1 and 0. If discord is detected, faulty address, written data, and read data are displayed following the error code 13, and the test is suspended. (6-3) 1930 SP ROM AVD RAM Video OUT Error: Not detected. The data including sub picture streams in ROM (IC104) are transferred to the RAM (IC504, IC505) in AVD (IC502), and output as video signals from the AVD (IC502). They are output from all video terminals (Composite, Y/C, Component) except EURO AV terminal.

7. Video
(7-2) Color Bar AVD color bar command write Video OUT Error: Not detected. The command is transferred to the AVD, and the color bar signals are output from video terminals. They are output from all video terminals (Composite, Y/C, Component) except EURO AV terminal.

5-4. ARP to RAM Address Bus Error 10: ARP - RAM Address B Address : 0000A55A Write Data : 00000000 Read Data : 00080000 Press NEXT Key to Continue Press PREV Key to Repeat _

8. Audio
(8-2) ARP 1930 Error 14 : ARP 1930 video NG 15 : ARP 1930 audio NG (8-3) Test Tone A pink noise signal is output from the AVD (IC502) through optical coaxial digital terminal and analog audio terminal. Error: Not detected. All channels 2ch Left 2ch Right Front Left Front Right Rear Left Rear Right Center Sub Woofer are checked in this order. Caution: Sub Woofer is checked only for low-frequency components, and no sound will be heard unless a proper super woofer is connected.

shows the data 0xA55A was read from address 0x00080000 though it was written to the address 0x00000000. This implies that these addresses are in the form of shadow. Also, if the read data is not 0xA55A, another error will be present. (5-5) ARP RAM Check Data write read, and accord check Error 11: ARP RAM read data discord The program code data stored in ROM are copied to all areas of RAM (IC303) connected to the ARP (IC302) through the bus, then they are read and checked if they accord. If the detail check was selected initially, the data are written to all areas and read, then the same test is conducted once again with the data where all bits are inverted between 1 and 0. If discord is detected, faulty address, written data, and read data are displayed following the error code 11, and the test is suspended.

6-3

Check Items List 2) Version (2-2) Revision (2-3) ROM Check Sum (2-4) Model Type (2-5) Region 3) Peripheral (3-2) EEPROM Check (3-3) Gate Array Check (3-4) NAND Flash Check (DVP-S570D/S745D) 4) Servo (4-2) Servo DSP Check (4-3) DSP Driver Test 5) Supply (5-2) ARP Register Check (5-3) ARP to RAM Data Bus (5-4) ARP to RAM Address Bus (5-5) ARP RAM Check 6) AV Decoder (6-2) 1930 RAM (6-3) 1930 SP 7) Video (7-2) Color Bar 8) Audio (8-2) ARP 1930 (8-3) Test Tone

Error Codes List 00: Error not detected 01: RAM write/read data discord 02: Gate array NG 03: EEPROM NG 04: Flash memory clear error 05: Flash memory write error 06: Flash memory read data discord 08: ARP register read data discord 09: ARP RAM data bus error 10: ARP RAM address bus error 11: ARP RAM read data discord 12: Servo DSP NG 13: 1930 SDRAM NG 14: ARP 1930 video NG 15: ARP 1930 audio NG 16: 1939 UCODE download NG 17: System call error (function not supported) 18: System call error (parameter error) 19: System call error (illegal ID number) 20: System call error (time out) 21: NAND Flash faulty blocks exceed 10 90: Error occurred 91: User verification NG 92: Diagnosis cancelled

6-4

6-4.

DRIVE AUTO ADJUSTMENT

On the Test Mode Menu screen, press [1] key on the remote commander, and the drive auto adjustment menu will be displayed.
## Drive Auto Adjustment ## Adjustment Menu 0. 1. 2. 3. 4. ALL DVD-SL CD DVD-DL SACD

1. DVD-SL (single layer) Select [1], insert DVD single layer disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM. DVD Single Layer Disc Adjustment Steps 1. SLED TILT Reset 2. Disc Check Memory SL 3. Wait 500 msec 4. Set Disc Type SL 5. LD ON 6. Spdl Start 7. Wait 1 sec 8. Focus Search ON 9. Focus Search OFF 10. Focus Servo ON 1 11. Auto Track Offset Adjust 12. Tracking ON 13. CLVA ON 14. Wait 1 sec 15. Sled ON 16. Check CLV Lock 17. Auto LFO Adjust 18. Auto Focus Offset Adjust 19. Auto Tilt Position Adjust 20. Auto Focus Gain Adjust 21. Auto Focus Offset Adjust 22. EQ Boost Adjust 23. Auto LFO Adjust 24. Auto Track Gain Adjust 25. All Servo Stop 26. Eep Copy Loop Filter Offset

Exit: RETURN

Normally, [0] is selected to adjust DVD (single layer), CD, DVD (dual layer), and SACD in this order. But, individual items can be adjusted for the case where adjustment is suspended due to an error. In this mode, the adjustment can be made easily through the operation following the message displayed on the screen. The disc used for adjustment must be the one specified for adjustment. However, for SACD disc, use the player with initial data if the disc is not available. 0. ALL You will be asked if EEPROM data are initialized or not, and for this prompt, select [0] and press the [ENTER] key, and the servo set data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD disc, 3. DVD-DL disc, and 4. SACD disc are adjusted in this order. Each time one disc was adjusted, it is ejected. Replace it with the specified disc following the message. Though the message to confirm whether discs other than SACD disc are adjusted is not displayed, you can finish the adjustment if pressing the [STOP] button. The S curve level, RF level, and jitter value can be confirmed during adjustment, and if OK, press the [ENTER] key and continue adjustment. (If NG, press the [STOP] button) During adjustment of each disc, the measurement for disc type judgment is made. As automatic adjustment does not judge the disc type unlike conventional models, take care not to insert wrong type discs. Also, do not give a shock during adjustment.

6-5

2. CD Select [2], insert CD disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM. CD Adjustment Steps 1. Sled Tilt Rest 2. Disc Check Memory CD 3. Wait 500 msec 4. Set Disc Type CD 5. LD ON 6. Spdl Start 7. Wait 1 sec 8. Focus Search ON 9. Focus Search OFF 10. Focus Servo ON 1 11. Auto Track Offset Adjust 12. Tracking ON 13. (TC Display Start) 14. CLVA ON 15. Wait 1 sec 16. Jitter Display Start 17. Sled ON 18. Check CLV ON 19. Auto LFO Adjust 20. Auto Focus Offset Adjust 21. Auto Focus Gain Adjust 22. Auto Focus Offset Adjust 23. Eq Boost Adjust 24. Auto LFO Adjust 25. Auto Track Gain Adjust 26. All Servo Stop

3. DVD-DL (dual layer) Select [3], insert DVD dual layer disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM. DVD Dual Layer Disc Adjustment Steps 1. Sled Tilt Reset 2. Disc Check Memory DL 3. Wait 500 msec 4. Set Disc Type DL 5. LD ON 6. Spdl Start 7. Wait 1 sec Layer 1 Adjust 8. Focus Servo ON 1 9. Auto Track Offset Adjust 10. Tracking ON 11. Clva ON 12. Wait 1 sec 13. Sled ON 14. Check CLV Lock 15. Auto Loop Filter Offset Adjust 16. Auto Focus Offset Adjust 17. Auto Focus Gain Adjust 18. Auto Focus Offset Adjust 19. Eq Boost Adjust 20. Auto Loop Filter Offset 21. Auto Track Gain Adjust Layer 0 Adjust 22. Fj (L1 L0) 23. Auto Track Offset Adjust L0 24. Tracking ON 25. Clva ON 26. Wait 1 sec 27. Sled ON 28. Check CLV Lock 29. Auto Loop Filter Offset Adjust 30. Auto Focus Offset Adjust 31. Auto Focus Gain Adjust 32. Auto Focus Offset Adjust 33. Eq Boost Adjust 34. Auto Loop Filter Offset 35. Auto Track Gain Adjust 36. All Servo Stop

6-6

4. SACD Select [4], insert SACD disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM. However, if SACD disc is not available, use the player with initial data, skipping the SACD adjustment. In this case, you can finish the adjustment if pressing the [STOP] button. SACD Adjustment Steps 1. Sled Tilt Reset 2. Set Disc Type CD 3. LD ON 4. Spdl Start 5. Wait 1 sec 6. Focus Servo ON 0 7. Auto track Offset Adjust 8. Tracking ON 9. CLVA ON 10. Wait 1 sec 11. Sled ON 12. Check CLV ON 13. Auto LFO Adjust 14. Auto Focus Offset Adjust 15. Auto Focus Gain Adjust 16. Auto Focus Offset Adjust 17. Eq Boost Adjust 18. Auto LFO Adjust 19. Auto Track Gain Adjust 20. All Servo Stop

6-5.

DRIVE MANUAL OPERATION

On the Test Mode Menu screen, select [2], and the manual operation menu will be displayed. For the manual operation, each servo on/off control and adjustment can be executed manually.
## Drive Manual Operation ## Operation Menu Disc type Servo Control Track/Layer Jump Manual Adjustment Auto Adjustment Memory Check

1. 2. 3. 4. 5. 6.

0. Disc Check Memory Exit: Return

In using the manual operation menu, take care of the following points. These commands do not provide protection, thus requiring correct operation. The sector address or time code field is displayed when a disc is loaded. 1. Set correctly the disc type to be used on the Disc Type screen. The disc type must be set after a disc was loaded. The set disc type is cleared when the tray is opened. 2. After power ON, if the Drive Manual Operation was selected, first perform "Reset SLED TILT" by opening 1. Disc Type screen. 3. In case of an alarm, immediately press the [STOP] button to stop the servo operation, and turn the power OFF. Basic operation (controllable from front panel or remote commander)

[POWER] [STOP] [OPEN/CLOSE] [RETURN] [NEXT], [PREV] [1] to [9], [0]
Cursor UP/DOWN

Power OFF Servo stop Stop+Eject/Loading Return to Operation Menu or Test Mode Menu Transition between sub modes of menu Selection of menu items Increase/Decrease in manually adjusted value

6-7

0. Disc Check Memory
Disc Check

1. SL Disc Check 2. CD Disc Check 3. DL Disc Check

0. Reset SLED TILT

Disc Type Disc Type Auto Check DVD SL 12 cm DVD DL 12 cm CD 12cm SACD 12 cm DVD SL 8 cm DVD DL 8 cm CD 8 cm SACD 8 cm Reset SLED TILT TC. : : EMG. 00 CD 12 cm 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.

Display when CD 12cm disc was selected
On this screen, the mirror time is measured to judge the disc and it is written to the EEPROM. First load DVD SL disc and press [1], next load CD disc and press [2], and finally load DVD DL disc and press [3]. The adjustment must be executed more than once after default data were written. External vibration or shock to the player must not be given. Reference value for DVD is from 10 to 20, and for CD, from 28 to 4F. Check that the value of CD is larger than that of DVD. When those values are beyond a range perform this adjustment again. From this screen, you can go to another mode by pressing [NEXT] or [PREV] key, but you cannot enter this mode from another mode. You can enter this mode from the Operation Menu screen only.

[0] Reset SLED TILT [1] Disk Type Check

Reset the Sled and Tilt to initial position. Judge automatically the loaded disc. As the judged result is displayed at the bottom of screen, make sure that it is correct. If Disc Check Memory menu has not been executed after EEPROM default setting, the disc type cannot be judged. In this case, return to the initial menu and make a check for three types of discs (SL, DL, CD). Select the loaded disc. The adjusted value is written to the address of selected disc. No further entry is necessary if [1] was selected.

[2] to [9] 1. Disc Type
1. 2. 3. 4. 5. 6. 7. 8. 9. 0. Disc Type Disc Type Auto Check DVD SL 12 cm DVD DL 12 cm CD 12cm SACD 12 cm DVD SL 8 cm DVD DL 8 cm CD 8 cm SACD 8 cm Reset SLED TILT EMG. 00

2. Servo Control
1. 2. 3. 4. 5. 6. 7. Servo Control LD Off R.Sled SP Off L.Sled Focus Off U.Tilt TRK. Off D.Tilt Sled Off CLVA Off FCS. Srch Off FWD REV Up Down

On this screen, select the disc type. To select the disc type, press the number of the loaded disc. The selected disc type is displayed at the bottom. Selecting [1] automatically selects and displays the disc type. In case of wrong display, retry "Disc Check Memory". Also, opening the tray causes the set disc type to be cleared. In this case, set the disc type again after loading. In performing manual operation, the disc type must be set. Once the disc type has been selected, the sector address or time code display field will appear as shown below. These values are displayed when PLL is locked.
Disc Type Disc Type Auto Check DVD SL 12 cm DVD DL 12 cm CD 12cm SACD 12 cm DVD SL 8 cm DVD DL 8 cm CD 8 cm SACD 8 cm Reset SLED TILT SA. SI. EMG. 00 DVD SL 12 cm 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.

0. Reset SLED TILT SA. SI. DVD SL 12 cm

EMG. 00

On this screen, the servo on/off control necessary for replay is executed. Normally, turn on each servo from 1 sequentially and when CLVA is turned on, the usual trace mode becomes active. In the trace mode, DVD sector address or CD time code is displayed. This is not displayed where the spindle is not locked. The spindle could run overriding the control if the spindle system is faulty or RF is not present. In such a case, do not operate CLVA.

Display when DVD SL 12cm disc was selected

6-8

[0] Reset SLED TILT [1] LD [2] SP [3] Focus [4] TRK [5] Sled [6] CLVA [7] FCS. Srch

Reset the Sled and Tilt to initial position. Turn ON/OFF the laser. Turn ON/OFF the spindle. Search the focus and turn on the focus. Turn ON/OFF the tracking servo. Turn ON/OFF the sled servo. Turn ON/OFF normal servo of spindle servo. Apply same voltage as that of focus search to the focus drive to check the focus drive system. Move the sled outward. Perform this operation with the tracking servo turned off. Move the sled inward. Perform this operation with the tracking servo turned off. Move the tilt upward. Move the tilt downward.

6-6.

MECHA AGING
### Mecha Aging ###

Press OPEN key

Abort: STOP key

Sled FWD

On the Test Mode Menu screen, selecting [3] executes the aging of mechanism. First, open the tray and load a disc. Press the [PLAY] key, and the aging will start. When the tray is closed, the disc type and size are judged and displayed. During aging, the repeat cycle is displayed. Aging can be aborted at any time by pressing the [STOP] key. After the operation has stopped, unload the disc and press again the [STOP] key or the [RETURN] key to return to the Test Mode Menu.

Sled REV

6-7.

EMERGENCY HISTORY
### MEG. History ###

Tilt UP Tilt DOWN

Laser Hours

CD DVD

xxxxxxxh xxxxxxxh

1. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Select: 1 � 9 Scroll: UP/DOWN (1: Last EMG.) Exit: Return

The following menus are normally not used.

3. Track/Layer Jump 4. Manual Adjustment 5. Auto Adjustment
The persons who do not know well about these menus should not use them.

6. Memory Check
EEPROM DATA Focus Gain TRK. Gain Focus Offset TRK. Offset L. F. Offset Analog FRSW PLL DAC Gain EQ Boost Jitter Mirror Time _ -� DL -� CD SACD SL L0 L1 xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx CLEAR: Default Set

On the Test Mode Menu screen, selecting [4] displays the information such as servo emergency history. The history information from last 1 up to 10 can be scrolled with key or key. Also, specific information can be displayed by directly entering that number with ten keys. The upper two lines display the laser ON total hours. Data below minutes are omitted. Clearing History Information Clearing laser hours Press [DISPLAY] and [CLEAR] keys in this order. Both CD and DVD data are cleared. Clearing emergency history Press [TITLE] and [CLEAR] keys in this order. Initializing set up data Press [DVD] and [CLEAR] keys in this order. The data have been initialized when "Set Up Initialized" message is displayed. The EMG. History screen will be restored soon.

This screen displays current servo adjusted data stored in the EEPROM. Though adjusted data can be initialized with the [CLEAR] key, they cannot be restored after initialization. So, before clearing, make a note of the adjusted data. For reference, the drive has been designed so that the gain center value is 20 and offset value is 80. Other values will be in a range of 10 to 80. If extreme value such as 00 or FF is set, adjustment will be faulty. In such a case, check for disc scratch or cable disconnection, then perform adjustment again.

6-9

How to see Emergency History
3 1 2

6-8.

VERSION INFORMATION
## Version Information ##

1.

IF con.

Ver. x. xxx (xxxx) Group 00

2

1: Emergency Code 2: Don't Care These codes are used for verification of software designing. 3: Historical order 1 to 9 Emergency Codes List 10: Communication to IC201 (MB-86 board) failed. 11: Each servo for focus, tracking, and spindle is unlocked. 12: Communication to EEPROM, IC101 (MB-86 board) failed. 13: Writing of hours meter data to EEPROM, IC101 (MB-86 board) failed. 14: Communication to Servo DSP IC404 (MB-86 board) failed, or Servo DSP is faulty. 20: Initialization of tilt servo and sled servo failed. They are not placed in the initial position. 21: Tilt servo operation error 22: Syscon made a request to move the tilt servo to wrong position. 23: Sled servo operation error 24: Syscon made a request to move the sled servo to wrong position. 30: Tracking balance adjustment error 31: Tracking gain adjustment error 32: Focus balance adjustment error 33: Focus bias adjustment error 34: Focus gain adjustment error 35: Tilt servo adjustment error 36: RF equalizer adjustment error 37: RF group delay adjustment error 38: Jitter value after adaptive servo operation is too large. 40: Focus servo does not operate. 41: With a dual layer (DL) disc, focus jump failed.50: CLV (spindle) servo does not operate. 51: Spindle does not stop. 60: With a DVD disc, Syscon made a request to seek nonexistent address. 61: With a CD disc, Syscon made a request to seek nonexistent address. 62: With a CD disc, Syscon made a request to seek nonexistent track No. and index No. 63: With a DVD disc, seeking of target address failed. 64: With a CD disc, seeking of target address failed. 65: With a CD disc, seeking of target index failed. 70: With a DVD disc, physical information data could not be read. 71: With a CD disc, TOC data could not be read. 80: Disc type judgment failed. 81: As disc type judgment failed, retry was repeated. 82: As disc type judgment failed, a measurement error occurred. 83: Disc type could not be judged within the specified time. 84: Illegal command code was received from Syscon. 85: Illegal command was received from Syscon.

Ver. x. xxx (xxxx) Model xx Region 0x Servo DSP. Ver. 1. xxxx

SYScon.

Exit: RETURN

On the Test Mode Menu screen, selecting [5] displays the ROM version and region code. The parenthesized hexadecimal number in version field is checksum value of ROM.

6-9.

VIDEO LEVEL ADJUSTMENT

On the Test Mode Menu screen, selecting [6] displays color bars for video level adjustment. During display of color bars, OSD disappears but the menu screen will be restored if pressing any key. : LINE OUT VIDEO (75 terminating resistance) Measuring instrument : Oscilloscope Adjustment device : RV501 on MB-86 board Specified value : 1.0 � 0.02 Vp-p Measurement point

1.0 � 0.02 Vp-p

6-10

6-10. IF CON SELF DIAGNOSTIC FUNCTION
1. AI-17 BOARD (IF CON) TEST MODE
The front board test mode is the IF CON self diagnostic mode. The IF CON can diagnose the functions of the front panel boards that the IF CON controls. Normally, the IF CON makes a serial communication with the SYSTEM CONTROL and operates following thecommands from the SYSTEM CONTROL, but in the Test mode, the IF CON operates independently from the SYSTEM CONTROL. In the Test mode, the following functions can be checked. 1. Button function 2. Remocon receiving function 3. SYSTEM CONTROL-IF CON serial communication 4. Click shuttle function 5. Fluorescent display tube lighting check Grid check Anode check 6. LED control function In the Test mode, the set operates same as usual, except voltage monitoring, communication monitoring, display of fluorescent display tube, and LED control. 1. The routine that monitors +3.3 V (PCONT) of MB-86 board is not provided. 2. The monitoring timer for serial communication with the SYSTEM CONTROL is not provided. The set is not placed in the Standby mode, even if the communication with SYSTEM CONTROL is normal. 3. Display of fluorescent display tube (normally, display is made following the commands from SYSTEM CONTROL) 4. LED control (normally, control is made following the commands from SYSTEM CONTROL)

2. OPERATION OF SELF CHECK MODE
The Self Check mode is the function to conduct the basic test to the FL display and DVD panel section. 2-1. Self Check Mode Transition Processing At the AC Power ON after IF CON was reset, the input to 8pin (P60) is judged and if "Low" is entered, the main unit transits to the Self Check mode. In this port input judgment, the result of 3time attempts must be same (assuming that the MB-86 board is not connected). While pressing the [STOP] key on the main unit with the IF CON in STANDBY mode, enter [RETURN] [DISPLAY] (or [SET UP]) on the remote commander, and the unit transits to the Self Check Mode. The Self Check mode terminates when the IF CON transits to the STANDBY mode.

6-11