Text preview for : TVP0321.pdf part of Sony TVP0321 Sony sony tv bulletins sony tv bulletins TVP0321.pdf



Back to : TVP0321.pdf | Home

TV Products CSV-1
Service Bulletin
Sony Service Company - Technical Services
A Division of Sony Electronics Inc.
Sony Drive, Park Ridge, New Jersey 07656



Model: KV-35V35, KV-35V75 No. 321
Subject: Correction for Vertical Sweep Bar in the PIP (Picture Date: August 11, 1997
and Picture)


Symptom:
(234) Faint Vertical Sweep Bar in the PIP (Picture and Picture).



Solution: If this vertical bar appears, please apply the following Circuit Change:


REF FORMER NEW
DESCRIPTION PART DESCRIPTION PART REMARKS
NUMBER NUMBER
C264 ELEC. CAP. 1-126-933-11 ELEC. CAP. 1-126-941-11 UV BOARD
100UF/16V 470UF/25V
C301 ELEC. CAP. 1-126-933-11 ELEC. CAP. 1-126-935-11 UV BOARD
100UF/16V 470UF/16V
JUMPER NONE 4.25 INCH N/A SEE
BETWEEN JUMPER ILLUSTRATION
JW245 WIRE, AWG24 NUMBER 1
AND JW241 OR 26
JUMPER NONE 3 INCH N/A SEE
BETWEEN JUMPER ILLUSTRATION
R261 WIRE, AWG24 NUMBER 1
AND CN262 OR 26,
JUMPER NONE 8.5 INCH N/A SEE
BETWEEN JUMPER ILLUSTRATION
THE TUNER WIRE, AWG18 NUMBER 1
AND CM302 AND NUMBER 2
JW226 JUMPER 4.7 OHM 1-247-775-00 SEE
RESISTOR ILLUSTRATION
NUMBER 1
JW096 JUMPER WIRE NONE A BOARD
(REMOVE)
JW097 JUMPER WIRE NOT USED A BOARD
(REMOVE)
Note: The above jumper wires are not supplied from National Parts Center.




Reference: PTG, Tanaka & Ishigaki PRINTED IN USA


PRINTED ON RECYCLED PAPER
Audio Products Service Bulletin No. xxx


Remove UV board from the chassis, and make the following changes.

1.. Change the value of capacitor C264, from (100uf/16V) to 470uf/25V capacitor.

2. Change the value of capacitor C301 from (100uf/16V) to 470uf/16V.

3. Add Jumper Wire, ( older side of board), between JW245 (CM302 side) and JW241
S JW241 is not
mounted. Solder wire to left side of JW241. (UV stamp side) on the Solder side of the UV board as shown on
Illustration 1. Dress wire as shown in Illustration 1.

4. Cut foil pattern as shown on Illustration 1 Right side of R261(solder side) thereby openingthe connection
between R261 and Pin #19 of CN262)
Add Jumper Wire to right side of R261.
Cut the foil pattern, See Illustration number 1, at Pin #19 of CN262.
Connect the jumper wire from R261 to pin 19 as shown on Illustration 1.
Jumper wire should be as short as possible, but dressed as shown in Illustration No.1.

Remove AV board from the chassis and make the following changes:

1. Cut the foil pattern of the AV board as shown Illustration 3. Cut ground pattern at point A. Cut pattern
between Points B & C.

2.. Add Jumper Wire to the Tuner ground lug, right side of cut A. See Illustration 2
Connect the other side of jumper wire to the UV board, solder side, ound side of CM302 as shown in
gr
Illustration.

3. Remove Jumper Wire (JW096 and JW097) from A board. (See Illustration 3)