Text preview for : Panel_SHARP_LQ197VC1L17_0_[DS].pdf part of . Various Panel SHARP LQ197VC1L17 0 [DS] . Various LCD Panels Panel_SHARP_LQ197VC1L17_0_[DS].pdf
Back to : Panel_SHARP_LQ197VC1L17_0 | Home
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
ECORDS OF REVISION MODEL No : LQ197VC1L17 SPEC No : LD-15218
DATE Rev No. PAGE SUMMARY NOTE
2005.03.01 1st Issue
- -
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
1. Application This specification sheets applies to the color 19.7" VGA TFT-LCD module LQ197VC1L17
* These specification sheets are proprietary products of SHARP CORPORATION ("SHARP") and includes
materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce
them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without
the express written per mission of SHARP.
* The device listed in these specification sheets was designed and manufactured for use in AV equipment.
* In case of using the device for applications such as control and safety equipment for transportation (airc
raft, trains, automobiles, and etc), rescue and security equipment and various safety related equipment
which require higher reliability and safety, take into consideration that appropriate measures such as
fail-safe functions and redun dant system design should be taken.
* Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applic
ations, telecommunication equipment (trunk lines), nuclear power control equipment and medical or other
equipment for life support.
* SHARP assumes no responsibility for any damage resulting from the use of the device which does not co
mply with the instructions and the precautions specified in these specification sheets.
* Contact and consult with a SHARP sales representative for any questions about this device.
2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film
Transistor). It is composed
of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit, inverter circuit, back light
system and etc. Graphics and texts can be displayed on a 640xRGBx480 dots panel with about 16 million
colors by
using LVDS and signal, +5V of +3.3 DC supply voltages and supply voltage for back light. Also, this
module includes the DC/AC inverter to drive the CCFT lamps.
.3. Mechanical Specifications
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
4. Input Terminals
4-1. TFT-LCD panel driving
CN1 (Interface signals and +3.3V DC power supply)
Using connectors DF14H-20P-1.25H (Hirose Electric Co., Ltd.)
Corresponding connectors DF14-20S-1.25C(Connector) (Hirose Electric Co., Ltd.)
DF14-2628SCFA(Terminal) (Hirose Electric Co., Ltd.)
Using LVDS Receiver Contained in a control IC. [THC63LVDF84A(Thine) compatible]
Corresponding LVDS Transmitter THC63LVDM83R(Thine) or DSC90C385AMT(NS) or compatible
Pin Symbol Function Remark
No.
1 Vcc +3.3V Power supply
2 Vcc +3.3V Power supply
3 GND Ground
4 GND Ground
5 RxIN0- LVDS CH0 data signal (-) LVDS
6 RxIN0+ LVDS CH0 data signal (+) LVDS
7 GND Ground
8 RxIN1- LVDS CH1 data signal (-) LVDS
9 RxIN1+ LVDS CH1 data signal (+) LVDS
10 GND Ground
11 RxIN2- LVDS CH2 data signal (-) LVDS
12 RxIN2+ LVDS CH2 data signal (+) LVDS
13 GND Ground
14 RxCLKIN- LVDS CK- data signal (-) LVDS
15 RxCLKIN+ LVDS CK+ data signal (+) LVDS
16 GND Ground
17 NC NC
18 NC NC
19 GND Ground
20 Back Lighton
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 3
Transmitter 20pin LVDS_SET
Pin No Data =L (GND) or Open =H (3.3V)
51 TA0 R0 (LSB) R2
52 TA1 R1 R3
54 TA2 R2 R4
55 TA3 R3 R5
56 TA4 R4 R6
3 TA5 R5 R7 (MSB)
4 TA6 G0 (LSB) G2
6 TB0 G1 G3
7 TB1 G2 G4
11 TB2 G3 G5
12 TB3 G4 G6
14 TB4 G5 G7 (MSB)
15 TB5 B0 (LSB) B2
19 TB6 B1 B3
20 TC0 B2 B4
22 TC1 B3 B5
23 TC2 B4 B6
24 TC3 B5 B7 (MSB)
27 TC4 (NA) (NA)
28 TC5 (NA) (NA)
30 TC6 DE DE
50 TD0 R6 R0 (LSB)
2 TD1 R7 (MSB) R1
8 TD2 G6 G0 (LSB)
10 TD3 G7 (MSB) G1
16 TD4 B6 B0 (LSB)
18 TD5 B7 (MSB) B1
25 TD6 (NA) (NA)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
4-4. Backlight
CN 2, 3, 4, 5
The module-side connector BHSR-02VS-1 (JST)
The user-side connector SM02-BHSS-1-TB (JST)
Pin no. symbol Function I O Cable color
1 VHIGH Power supply for lamp 1 (High voltage side) I Blue or Pink
2 VLOW Power supply for lamp 1 (Low voltage side) I Brown or White
Parameter Symbol Condition Applied pin Ratings Unit Remark
Supply voltage Vcc Ta=25 Vcc 0.3 + 4.0 Note1
Lamp Input voltage 0 + 2000
VHIGH rms
Storage temperature 30 + 70
TSTG
Operating
Panel surface 0 + 60
temperature TOPA
Input voltage VI1
Ta=25 0.3 0.3
RxIN-/+(i=0,1,2)
RxCLKIN-/+
0.3 Vcc
Ta=25 LVDS_SET
VI2 0.3
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
6. Electrical Characteristics
6-1. TFT-LCD panel driving Ta 25
Note1
On-off sequences of Vcc and data Dip conditions for supply voltage
0 t1 10ms 1) Vth Vcc Vmin
0 t2 10ms td 10ms
0 t3 1s 2) Vcc Vth
1s t4 Vcc-dip conditions should also
200ms t5 follow the on-off conditions
200ms t6
It is recommended to consider some timing difference between LVDS input and Backlight input as
shown above.
If the Backlight lights on before LCD starting, or if the Backlight is kept on after LCD stopping, the
screen may look white for a moment or abnormal image may be displayed. This is caused by variation in
output signal from timing generator at LVDS input on or off. It does not cause the damage to the LCD
module.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
6-2. Backlight The back light system is an edge-lighting type with four CCFTs (Cold Cathode Fluorescent Tube). The
characteristics of the lamp are shown in the following table. The value mentioned below is at VJG ECUG QH QPG %%(6
%%(6 /QFGN 0COG -6$'/56(/#<
56#0.'; '.'%64+% %1 .6&
Parameter Symbol Min. Typ. Max. Unit Remark
Lamp current range IL 3.5 6.0 7.5 mArms ( Note 1 )
Lamp voltage VL 625 720 Vrms Ta=25 , IL =6.0mArms
Lamp powe consumption PL 3.75 4.32 W ( Note 2 ) IL =6.0mArms
Lamp frequency FL 40 60 70 kHz ( Note 3 )
Kick-off voltage Vs 1480 Vrms Ta=0 ( Note 4 )
Lamp life time TL 50,000 hour ( Note 5 )
Note1 A lamp can be light in the range of lamp current shown above.
Maximum rating for current is measured by high frequency current measurement
equipment connected to VLOW at circuit showed below. (Note : To keep enough
kick-off voltage and necessary steady voltage for CCFT.) Lamp
Note3 Lamp frequency may produce interference with horizontal synchronous frequency, and this may cause beat on
the display. Therefore lamp frequency shall be detached as much as possible from the horizontal synchronous frequency
and from the harmonics of horizontal synchronous to avoid interference.
rise up in the user set, please decide the open output voltage by checking not to occur lighting failure
under operating state. The open output voltage should be applied to the lamp for more than 1 second to startup.
Otherwise the lamp may not be turned on.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Note
The performance of the backlight, for example lifetime or brightness, is much influenced by the characteristics of the
DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting caused by the
mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. When you confirm it, the module should
be operated in the same condition as it is installed in your instrument.
Use the lamp inverter power source incorporating such safeguard as overvoltage / overcurrent protective circuit or lamp
voltage waveform detection circuit, which should have individual control of each lamp. In case one circuit without such
individual control is connected to more than two lamps, excessive current may flow into one lamp when the other one is not in
operation.
Under the environment of 101x or less,miss-lighting or lighting delay may occur..
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
Graphics and texts can be displayed on a 640 RGB 480 dots panel with 16M colors by supplying
18 bit data signal (6bit/color [253 gray scales] 3 ).
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 10
8. Input Signals, Basic Display Colors and Gray Scale of Each Color
6bit input
'
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 11
9 Optical Characteristics Ta=25 , Vcc =+3.3V
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 12
Note1 Definitions of viewing angle range:
Note4 This shall be measured at center of the screen.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 13
Note5 Definition of white uniformity:
White uniformity is defined as the following with five measurements (A E).
10. Handling Precautions
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or
twist.
c) Since the front polarize is easily damaged, pay attention not to scratch it.
d) Since long contact with water may cause discoloration or spots, wipe off water drop immediately.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle
with care..
g) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into
consideration when handling.
h) Make sure the four mounting holes of the module are grounded sufficiently. Take electro-magnetic
interference (EMI) into consideration.
i) The module has some printed circuit boards (PCBs) on the back side. Take care to keep them form any
stress or pressure when handling or installing the module; otherwise some of electronic parts on the
PCBs may be damaged.
j) Observe all other precautionary requirements in handling components.
k) Since it is necessary to remove the screw on the back of a module before performing lamp exchange,
please take a cabinet design into consideration.
l) When some pressure is added onto the module from rear side constantly, it causes display non-uniformity
issue, functional defect, etc. So, please avoid such design.
m) When handling LCD modules and assembling them into cabinets, please be noted that long-term
storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent,
solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the
LCD modules.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 14
11. Packing form
a) Piling number of cartons : maximum 5 cartons
b) Packing quantity in one carton : 5 module
c) Carton size : 706mm(W) 532mm(D) 421mm(H)
d) Total mass of one carton filled with full modules : 25kg.Max
e) Packing form is shown in Fig.3
Note A gap of panel shall not occur by vibration or the shock.
Result Evaluation Criteria
Under the display quality test conditions with normal operation state, these shall be no change
which may affect practical display function.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 15
13 Others
1) Lot No. and indication Bar Code Label:
3) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is
changed, the specification may not be satisfied.
4) Disassembling the module can cause permanent damage and should be strictly avoided.
5) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.
6) The chemical compound which causes the destruction of ozone layer is not being used.
7) Warning of mercury and material information of LPG (Light Pipe Guide) are labeled on the back of the
module.
8)Cold cathode fluorescent lamp in LCD PANEL contains a small amount of mercury, Please follow local
ordinances or regulations for disposal. (put on the back of the module. )
9) This specification document's Japanese language version is also available. Its Number (SPEC.No.) is
LD-15218
10) When any question or issue occurs, it shall be solved by mutual discussion.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 16
14. Carton storage condition
Temperature 0 to 40
Humidity 95%RH or less
(winter)
Sunlight Be sure to shelter a product from the direct sunlight.
Atmosphere Harmful gas, such as acid and alkali which bites electronic components and/or
wires must not be detected.
Notes Be sure to put cartons on palette or base, don't put it on floor, and store them with
removing from wall
Please take care of ventilation in storehouse and around cartons, and control
changing temperature is within limits of natural environment
Storage period 1 year
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
15218 17
LD
SHARP
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
SHARP LD 15218 18
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com