Text preview for : BDT-30 & 230 & 3 & 120.pdf part of Harman Kardon BDT-30 & 230 & 3 & 120 Harman Kardon BDP BDT-30 & 230 & 3 & 120 BDT-30 & 230 & 3 & 120.pdf
Back to : BDT-30 & 230 & 3 & 120.pd | Home
harman/kardon Service Manual
BDT 30/230
BDT 3/120
Blu-ray player
CONTENTS
ESD WARNING 2 SPECIFICATIONS 10
OWNER'S MANUAL FRONT PAGE 3 EXPLODED VIEW 11
REGION CODES 4 BDT 3 PARTS LIST 12
FEATURES 5 BDT 30 PARTS LIST 13
FRONT PANEL CONTROLS 6 SOFTWARE UPGRADE INSTRUCTIONS 14
REAR-PANEL CONNECTIONS 7 TROUBLESHOOTING CHARTS 15
REMOTE CONTROL FUNCTIONS 7 PCB DRAWINGS 19
TROUBLESHOOTING 9 WIRING DIAGRAM 23
SCHEMATIC DIAGRAMS 24-35
Released EU2011 Harman Consumer Group, Inc. Rev 0, 10/2011
8500 Balboa Boulevard
Northridge, California 91329
Harman Kardon BDT 3/120V and BDT 30/240V Service Manual
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and
semiconductor "chip" components.
The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge build-up or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges
sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical change sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement
ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together
or your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES devices.
Each precaution in this manual should be followed during servicing.
Components identified with the IEC symbol in the parts list are special significance to safety. When replacing a component identified with
, use only the replacement parts designated, or parts with the same ratings or resistance, wattage, or voltage that are designated in the
parts list in this manual. Leakage-current or resistance measurements must be made to determine that exposed parts are acceptably
insulated from the supply circuit before retuming the product to the customer.
Page 2 of 35
Harman Kardon BDT 3/120V and BDT 30/240V Service Manual
BDT 3/BDT 30
Blu-ray DiscTM player
Owner's Manual
Page 3 of 35
Harman Kardon BDT 3/120V and BDT 30/240V Service Manual
Unpacking
Unpacking Thank You for Choosing Harman Kardon