Text preview for : 410-TE.pdf part of MAKITA 410-TE MAKITA 410-TE.pdf
Back to : 410-TE.pdf | Home
T ECHNICAL INFORMATION
Models No. 410
New Tool
Description MAKITA Dust collector 287
CONCEPTION AND MAIN APPLICATIONS
The dust collector mainly for collecting the
280
wood chips discharged from the various
wood processing machine. Once the special
accessories or the hose and nozzle etc. have
been installed, this machine also can act as
the Conveyance equipment for cutting wastes or the Blower.
28
5
Specifications
Voltage (V) Current (A) Cycle (Hz) Continuous rating Max. Output(W)
Input(W) Output(W)
100 11.0 50/60 1050 650 820
115 9.0 50/60 900 610 770
200 5.5 50/60 1050 650 820
220 4.7 50/60 900 610 770
230 4.5 50/60 900 610 770
240 4.3 50/60 900 610 770
No load speed (R.P.M.) 10000/min
Max. peak air flow 8.7 m3/min
510 mm in water column (*The air volume and vacuum degree
Max. sealed suction
while the hose and dust bag are being installed.)
Net Weight (kg) 9.3 kg
power supply cord (m) 5m
Standard equipment
Dust bag---One piece
Hose complete(2.5 m in length)---One piece
Optional accessories
Each hood for each large model wood process machine(#2004, #2006, #2030, #2030N, #2040)
Nozzle and cover(for blowing)
Hose complete(same as the ones for the normal accessories)
Hose 5m, 10m,
Hose joint(for extending the hose)
Clamp 90(for fixing the hose)
Features and benefits
1. The Dust collecting amount can reach to 200 L corresponding to that of the large model, regardless of the small
model and light weight.(The capacity of Hitachi R-100 model with weight of 30 kg : 180L)
2. The safety switch with which the operation cannot start unless the hose or the cover is installed on the suction
port.
3. The vibration proof construction, wherein the fan vibration caused by high speed rotation is not released to
outside.
4. The heating damage preventing unit is mounted to protect the motor from heating damage by the overload caused
when the debris accidentally has been clogged in the fan.
5. With the built-in peep hole on the dust bag, the dust amount can be easily checked.
6. The accessory hood allows to collect cutting chips directly from the large model wood processing machine.
7. Once the attached nozzle and cover have been installed, the machine can play as the Blower.
The standard equipment for the tools shown may differ form country to country
Capacity
1. Relationship between the length of hose and air volume.
Length of hose (m) 2.5 5.0 10.0 20.0
Air volume (m3/min.) 8.7 7.8 7.0 4.9
2. The length of hose which is available when collecting or transporting directly of portions from large machine for
wood(The total length of both intake and exhaust sides of hose).
Model Length of hose which is available (m)
2004
2006
2030N, 2031N
20 m
2030NC, 2031NC
LM3001, 2030 Note) If the value of length
2031, 2032 exceeds that of the above,
2040 2.5 m chips are sometimes blocked.
Repair
1
3
Curling
Inlet Moter cover
Carbon brush
Brush holder
Mount
2
4
Base
Screw driver
Cushion
(1) Replacing of the carbon brush
a. Loosen the screws 1 and2 to disconnect the inlet and curling.
b. Loosen the screw 3 to disconnect the motor cover. At this time insert the screw driver through the base hole to
loosen the 2 pieces of screws at under side.
c. Loosen the screw 4 to replace the carbon brush. Be sure to insert the tool on the edge of the field lead wire into
the tool of the carbon brush at this time.
Screw lock super 103Q
(Reference) The service life of the carbon brush is about 1,000-hr.
(2) Mounting of the cushion
Apply the screw lock super 103Q and screw at
the fastening torque of 3.5 kg-cm.
Base
(3) Mounting of the mount(Vibration proof rubber) Cushion
Mount
Manually fasten the mount while holding the
rubber portion by hands.
(4) Mounting of the fan 130
The fastening torque of the nut is 100-200 kg-cm.
Tool portion
(5) Replacing of the motor Rubber portion
For replacing the motor, see the technical information of #401(BL-0765). Use care that the fan for cooling the
motor is screwed by the left-handed screw.
(6) Tool required
+screw driver
Spanner 8, 10, 14
Plate spanner(Thin port) 19
Box wrench 17