Text preview for : Radio Shack 32-2055 User Manual.pdf part of Radio Shack 32-2055 RadioShack 32-2055 250-Watt Stereo PA Amplifier User Manual
Back to : Radio Shack 32-2055 User | Home
32-2055
250-Watt · Stereo
PA Amplifier
Thank you for purchasing your 250-Watt · Stereo PA Amplifier from
RadioShack. This PA gives you the versatility and power you need in a
professional sound system. Its wide frequency response easily handles
amplification of voice and music. Use it anywhere you need to deliver
special announcements with excellent sound. It is perfect for meeting halls,
auditoriums, sporting events, schools, or in the office for paging systems.
With a bridged speaker connection, the amplifier can produce up to 350
watts of clean, powerful sound with minimum distortion.
What's Included
PA Amplifier
User's Guide
Quick Start Guide
www.radioshack.com
Contents
Important Safety Instructions ............................................................................ 3
About Your Amplifier ......................................................................... 6
Amplifier Features.............................................................................................. 6
Amplifier Setup............................................................................................ 10
Getting Started ................................................................................................. 10
Select a Location................................................................................................... 10
Preset the Controls ............................................................................................... 10
Preset the Audio Input Source........................................................................... 10
Presetting the Amplifier ..................................................................................... 10
Connecting Your Amplifier................................................................................ 11
Connecting Input Sources.................................................................................... 11
Connecting Microphones .................................................................................... 11
Connecting a Turntable........................................................................................ 12
Connecting an Auxiliary Sound Source .............................................................. 12
Connecting the MIX BUS Jack............................................................................. 12
Connecting an Equalizer ...................................................................................... 13
Connecting Speakers ........................................................................................... 13
Determining Total Speaker Impedance ............................................................ 14
Preparing the Speaker Wires ............................................................................. 14
Connecting Two Speakers in Series .................................................................. 15
Connecting Two Speakers in Parallel ................................................................ 15
Unbridged Connection ...................................................................................... 16
Bridged Connection ........................................................................................... 16
Connecting Power ................................................................................................ 17
Operating Your Amplifier............................................................................. 18
Beginning Steps ...................................................................................................... 18
Monitoring Sound Sources .................................................................................. 18
Listening Safely ..................................................................................................... 18
Using the Feedback Filter .................................................................................... 19
Using the Level Meters and Clipping Indicator ................................................. 19
Using Speaker A/B................................................................................................ 19
Additional Information................................................................................. 20
Care and Service .............................................................................................. 20
Replacing the Fuse ............................................................................................... 20
Troubleshooting.................................................................................................... 21
Specifications ........................................................................................................ 22
Do More with Your Amplifier ........................................................................... 23
2
Important Safety Instructions
1. Read all safety and operating instructions before the appliance is used.
2. Keep all safety and operating instructions for future reference.
3. Follow all warnings on the appliance and in the operating instructions.
4. Unplug this appliance from the wall outlet before cleaning. Use only a damp
cloth for cleaning. Do not use liquid or aerosol cleaners.
5. Do not use this appliance near water (for example, near a bathtub,
washbowl, kitchen sink, or laundry tub; in a wet basement; or near a
swimming pool).
6. Do not place this appliance on an unstable cart, stand, tripod, bracket,
or table. The appliance may fall, causing serious injury to a child or adult,
and serious damage to the appliance. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer or sold with the
appliance. Follow the manufacturer's instructions for mounting, and use a
recommended mounting accessory.
7. Slots and openings in the cabinet provide ventilation, ensure reliable
operation, and protect from overheating. Do not block or cover these
openings, and do not place the appliance on a bed, sofa, rug, or other
similar surface. Do not place the appliance in a built-in installation such as
a bookcase or rack unless it provides proper ventilation as specified by the
manufacturer.
8. Keep appliance away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
9. Operate this appliance using only the power source indicated on its marking
label. If you are not sure of your home's power type, consult your appliance
dealer or local power company.
10. This device is equipped with a three-wire grounding-type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are unable to insert the plug into
the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type plug.
11. Route power-supply cords so they are not likely to be walked on or pinched
by items placed on or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit from the
appliance.
3
12. Clean only as recommended by the manufacturer.
13. An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or
circuits as contact with them might be fatal.
14. Unplug the power cord from the outlet when you know that you will not be
using the appliance for a long period of time.
15. Do not overload wall outlets, extension cords, or integral convenience
receptacles, as this can result in a risk of fire or electric shock.
16. Never push objects of any kind into this appliance through openings, as
they may touch dangerous voltage points or short out parts that could result
in a fire or electric shock. Never spill liquid of any kind on the appliance.
17. Move appliance and cart combinations with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance and cart combination
to overturn.
18. Unplug this appliance from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
· When the power-supply cord or plug is damaged.
· If liquid has been spilled or objects have fallen into the appliance.
· If the appliance has been exposed to rain or water.
· If the appliance does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the appliance to normal operation.
· If the appliance has been dropped or damaged in any way.
· When the appliance exhibits a distinct change in performance.
19. Do not attempt to service this appliance yourself, as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
20. When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
4
21. Upon completion of any service or repairs to this appliance, ask the service
technician to perform safety checks to determine that the appliance is in
proper operating condition.
22. For added protection for this product during a lightning storm, unplug
it from the wall outlet. This will prevent damage to the product due to
lightning and power line surges.
23. Only use attachments recommended by the product manufacturer.
24. The product should be mounted to a wall or ceiling only as recommended
by the manufacturer.
25. Overloading -- Do not overload wall outlets, extension cords, or integral
convenience receptacles, as this can result in a risk of fire or electric shock.
WARNING: To reduce the risk of fire or shock hazard, do not expose
this product to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER OR BACK. NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
This symbol is intended to alert you to the presence of un-
insulated dangerous voltage within the product's enclosure
that might be of sufficient magnitude to constitute a risk of
electric shock. Do not open the product's case.
This symbol is intended to inform you that important
operating and maintenance instructions are included in the
literature accompanying this product.
5
About Your Amplifier
Amplifier Features
Output Power
Illuminated Power PHONES Jack Level Indicators
Switch Connect Indicates the total
Lights up when you headphones stereo output
turn on the switch. here. power level.
A/B Speaker Switch MIC 1, MIC 2, MIC 3
Select the speakers you want Adjust volume for the
to use with the amplifier in connected microphones.
Channel A, Channel B, or
both (for use with 8 ohm
speakers only).
6
About Your Amplifier
PROTECTION Indicator
Lights up when the
amplifier overheats or
CLIPPING Indicator if a shorted load occurs
CD/AUX Lights up to remind on the amplifier output.
Adjust volume of you to reduce volume The amplifier resets itself
CD or auxiliary when the amplifier when the problem is
sound source. output is too high. corrected.
MIC 4/PHONO FEEDBACK FILTER Volume Control:
Adjust volume Turn to control audio Left/Right speakers
of connected feedback. Turn to regulate volume of
microphone (MIC 4) left and right speakers.
or turntable.
7
About Your Amplifier
Cooling Fan ¼" Stereo Input
Automatically activated Jacks
XLR Balanced whenever the amplifier Connect stereo
Microphone Inputs is turned on. This air input sources (CD
Connect up to four cooling system rapidly or DVD player, TV,
high impedance disperses interior heat etc.) here using a
microphones to your to reduce operating ¼-inch (balanced)
amplifier. temperature. audio cable.
¼" Unbalanced MIC 4/PHONO Phono Input Jacks
Microphone Inputs Switch Connect your turntable here.
Connect up to four Select MIC 4 or
MIX BUS Jack
microphones to your PHONO input.
amplifier using a ¼" Connect an extra amplifier if you
unbalanced cable, for have multiple audio sources.
left and right mono CD/AUX Jack
sound. Connect any high-level sound
source for music or special effects.
EQ IN/OUT Jacks
Connect an equalizer or other
external processor.
8
About Your Amplifier
Audio Input Jacks
Connect input sources
(CD or DVD player,
TV, etc.) here using an STEREO/MONO Selector
unbalanced audio cable. Select bridged mono input
Match the colors on your mode in combination with a
cable connections with mono signal source plugged
the colors on the jacks. into the left channel.
Fuse
GND
(Ground Wire Connection)
EQ/BYPASS Selector Speaker Terminals
Select EQ if you are Connect two sets of speakers
using an equalizer (Left and Right, for A and B).
or BYPASS if you are
using another external
processor.
9
Amplifier Setup
Getting Started
Select a Location
Before you use your amplifier, be sure to place it on a surface with adequate
ventilation. Do not put it on thick carpeting, which can restrict air flow, or near a
heat source such as a heat vent or radiator, which can cause it to overheat.
Preset the Controls
Before you begin connecting or using your amplifier, preset the controls on the
audio input source and amplifier to avoid overdriving a channel or producing
loud sounds.
Preset the Audio Input Source
Set the controls on the audio input sources to the following levels:
Audio Device Control Setting
Turntable Power Flat
Tape Deck Power Flat
CD Player Power Flat
Amplifier Power Flat
Receiver Tone Off
Presetting the Amplifier
To prevent excessive volume and possible hearing damage, set the controls on
the amplifier to the following:
Control Setting
POWER Off
MIC 1, MIC 2, MIC 3, MIC 4/PHONO, Min
CD/AUX Volume Control
LEFT and RIGHT Volume Control Min
After you turn on the amplifier or change the program source, set the controls to
a comfortable listening level.
10
Connecting Your Amplifier
Connecting Your Amplifier
Connecting Input Sources
You can connect optional components, such as microphones, tuner, turntable,
audio mixer, preamplifier, or CD player to your amplifier to expand your system.
To prevent hum and other noise, use low-capacitance shielded cable (not
supplied, available at your local RadioShack store or at www.radioshack.com).
Notes:
· This amplifier is equipped with both stereo phono input and ¼-inch
(6.35 mm) jacks. The ¼-inch input jacks on the top are stereo while the
others are left and right mono.
· Before you make any connections, be sure the amplifier is turned off
and AC power cord is not plugged in.
Connecting Microphones
You can connect up to four high- or low-impedance microphones (not supplied)
to the microphone inputs on the back of the amplifier. Each input (MIC1, MIC2,
MIC3, and MIC4) has a balanced and unbalanced jack. You need a microphone
with a ¼-inch (6.35 mm) plug to connect to an unbalanced jack or a microphone
cord with a 3-pin XLR plug to connect to a balanced jack.
Balanced Unbalanced
Microphone Microphone Jacks
Jacks
MIC 4/PHONO Switch
Notes:
· If your microphone cord is longer than 20 feet (6 meters), we
recommend that you connect it to a balanced jack to reduce signal
hum.
· If you connect a microphone to both balanced and unbalanced jacks
for MIC1, MIC2, MIC3, or MIC4, the microphone you connect to the
unbalanced jack has priority.
· If you connect a microphone to either MIC4 jack, set the MIC4/PHONO
switch to MIC4.
11
Connecting Your Amplifier
Connecting a Turntable
Connect your low-level audio input source (turntable) to the L PHONO and
R PHONO jacks on the back of the amplifier. If you connect a low-level audio
input source to the PHONO jacks, set the MIC4/PHONO switch to PHONO.
To avoid a low-level hum, connect your turntable's ground wire (usually black or
green) to the GND terminal on the amplifier.
MIC 4/ PHONO GND Terminal
Switch
PHONO Input Jacks
Connecting an Auxiliary Sound Source
Connect any high-level sound source, such as a CD player, tape deck, or tuner,
to the CD/AUX jack on the back of the amplifier.
CD/AUX Jack
Connecting the MIX BUS Jack
Connect another amplifier (same model) to double the size of your PA system.
You can then use up to eight microphones (or six microphones and two
turntables) and two auxiliary sound sources.
Use a shield cable with phono plugs at each end. Connect the cable between
the MIX BUS jacks on the back of the two amplifiers.
Note: For best results, do not use cable longer than 6 feet (1.8 meters).
MIX BUS Jack
12
Connecting Your Amplifier
Connecting an Equalizer
Connect an equalizer or other external signal processor to the EQ IN and
EQ OUT jacks on the back of the amplifier.
EQ IN/OUT Jacks
Notes:
· You can also connect a tape deck to the EQ OUT jack for recording.
· The EQ IN/OUT jacks handle the signal from an outside equalizer. They
do not handle the signal from an outside equalizer's stereo INPUT jacks.
Connecting Speakers
You can connect one or more 4-, 8-, or 16-Ohm speakers to the amplifier. To
ensure equal volume from each speaker, all connected speakers should have the
same impedance rating.
Proper phasing is important when you use more than one speaker in the same
room or area. Out-of-phase speakers can lose up to one-half of their potential
volume, and can have a significantly decreased bass effect.
Most speaker terminals are color-coded or have a mark that indicates the
terminal's polarity. Usually, terminals with positive polarity are red or have a
plus symbol (+), and terminals with negative polarity are black or have a minus
symbol (). Phasing is correct when you connect + to + and to .
You can also bridge the amplifier's channels. The amplifier has two channels:
A and B. If you connect two pairs of speakers, follow these guidelines:
· Speakers connected to the same channel (A or B) are part of a pair and
must be of the same impedance.
· Speakers connected to different channels (A or B) are not part of a pair
and can be of different impedance.
STEREO/MONO Switch
Speaker Terminals
13
Connecting Your Amplifier
Determining Total Speaker Impedance
Before you connect speakers to the amplifier, you must determine the total
speaker impedance. To determine total speaker impedance, you must first
decide if you are going to connect the speakers in series, parallel, or a series/
parallel combination.
If you are connecting more than two speakers in series only or parallel only, be
sure the total impedance does not exceed the amplifier's maximum impedance
(16 ohms) or fall below the minimum impedance (4 ohms). You can achieve a
proper total impedance by combining series and parallel connections.
Note: A total speaker impedance higher than 16 ohms or lower than
4 ohms can damage your amplifier or speakers. When determining the
total speaker impedance, first determine whether you are connecting
the speakers in series, parallel, or a series/parallel combination.
Preparing the Speaker Wires
Use the shortest length of wire possible to connect the speakers. After placing
the speakers, use this table to determine the wire length and choose the
appropriate gauge.
Wire Length Wire Gauge
7.6 m 18 gauge
(25 ft) or less
Over 7.6 m 16 gauge
(25 ft)
To prepare the speaker wire, remove about ½ inch (12.5 mm) of insulation from
the end you are connecting to the amplifier. Twist the exposed wire to secure all
of the wire strands.
14
Connecting Your Amplifier
Connecting Two Speakers in Series
Speakers are connected in series when the first speaker's positive terminal is
connected to the next speaker's negative terminal.
Note: Determine the total speaker impedance of speakers you want
to connect in series by adding up the individual impedances of all
connected speakers.
For example: If connecting two 4-ohm speakers in series, your total
speaker impedance is 8 ohms.
Connecting Two Speakers in Parallel
Speakers are connected in parallel when the speakers' negative terminals are
connected together and all their positive terminals are connected together.
Note: Determine the total speaker impedance of speakers you want
to connect in parallel by dividing the impedance of one speaker by the
number of speakers.
For example: If connecting two 8-ohm speakers in parallel, divide 8
(one speaker's impedance) by 2 (number of speakers). Your total speaker
impedance is 4.
15
Connecting Your Amplifier
Unbridged Connection
Use this connection if you are connecting more than one speaker on the same
channel or if you do not have high power speakers.
1. Connect the speaker wires to the corresponding left and right positive (+)
and negative () speaker terminals.
2. Connect the other end of the left and right speaker's positive (+) and
negative () wires to the amplifier's corresponding SPEAKER LEFT and
SPEAKER RIGHT terminals for each channel. To connect speaker wires to
the amplifier, turn the knob on the terminal counterclockwise until it stops,
insert the bare wire inside the space between the knob and the amplifier,
and turn the knob clockwise until it stops, securing the wire.
3. Make sure the STEREO/MONO switch is set to STEREO.
RIGHT Speaker LEFT Speaker
Bridged Connection
Use this connection if you have high power speakers that can handle a power
output of 350 Watts.
Note: For a bridged connection, do not connect any speaker wire to the
black SPEAKER terminals.
1. Connect the speaker wires to the speaker's positive (+) and negative ()
terminals.
16
Connecting Your Amplifier
2. Connect the other end of the speaker's positive (+) and negative () wires to
the amplifier's red SPEAKER LEFT and SPEAKER RIGHT terminals.
Note: SPEAKER RIGHT (+) on the amplifier is used as a negative ()
terminal for a bridged connection.
3. Make sure STEREO/MONO is set to MONO.
Note: In the bridged mono mode, only the LEFT volume control adjusts
the output level.
RIGHT Speaker LEFT Speaker
Connecting Power
To power the amplifier, plug the attached power cord into a standard AC
outlet. Your amplifier's fuse protects it from voltage surges. If the amplifier
does not turn on when you press POWER, check the fuse. If it is blown, see
"Replacing the Fuse."
17
Operating Your Amplifier
Beginning Steps
1. Start the input sound source.
2. Make sure the LEFT and RIGHT volume controls on the front of the amplifier
are set to MIN.
3. Press POWER to turn on the amplifier. The blue light around the power
switch and LEFT and RIGHT volume controls will light.
4. Rotate LEFT and RIGHT volume controls to their middle positions.
5. One at a time, adjust MIC1, MIC2, MIC3, MIC4/PHONO, and CD/AUX to
the desired volume and balance.
If you hear feedback after you adjust these controls, turn FEEDBACK FILTER
clockwise until the noise disappears (see "Using the Feedback Filter").
6. Adjust LEFT and RIGHT volume controls to the desired volume level after
you find your desired balance.
Monitoring Sound Sources
To monitor sound sources, plug a pair of mono or stereo headphones (not
supplied) with a ¼-inch (6.35mm) plug into the PHONES jack on the front of the
amplifier. Headphones sometimes make it easier to check and adjust the sound
source's balance.
Listening Safely
To protect your hearing, follow these guidelines when you use headphones.
· Set the volume to the lowest setting before you begin listening. After you
begin listening, adjust the volume to a comfortable level.
· Do not listen at extremely high volume levels. Extended high-volume
listening can lead to permanent hearing loss.
· Once you set the volume, do not increase it. Over time, your ears adapt to
the volume level, so a volume level that does not cause discomfort might
still damage your hearing.
18
Operating Your Amplifier
Using the Feedback Filter
The FEEDBACK FILTER control lets you reduce or eliminate squeal and other
noise caused by feedback. After you adjust LEFT and RIGHT volume, MIC1,
MIC2, MIC3, MIC4/PHONO, and CD/AUX , turn on the amplifier and any
connected sound sources. If you hear any feedback, turn FEEDBACK FILTER
clockwise until you reduce or eliminate the feedback.
Note: The FEEDBACK FILTER control decreases feedback frequencies
by up to 12dB. If it does not eliminate the feedback, try using a
frequency equalizer to further decrease the feedback frequencies.
Using the Level Meters and Clipping Indicator
The output indicators reflect the amplifier's output level. The stronger the signal
the more indicators light. The maximum signal through the amplifier should
cause the CLIPPING indicator to blink at peak music levels.
Output
Power
Level
Clipping Indicator
Indicators
Using Speaker A/B
Press SPEAKER A or SPEAKER B on the front of the amplifier for the channel
you want to listen to. If you have 8-Ohm speakers, press SPEAKER A and
SPEAKER B to listen to all connected speakers.
Speaker A
Speaker B
Note: If you have connected 4-Ohm speakers to the amplifier, do not
press in both SPEAKER A and SPEAKER B.
19
Additional Information
Care and Service
Keep the amplifier dry. If it gets wet, wipe it dry immediately. Use and store
the amplifier only in normal temperature environments. Handle the amplifier
carefully; do not drop it. Keep the amplifier away from dust and dirt, and wipe it
with a damp cloth occasionally to keep it looking new.
If your amplifier is not performing as it should, take it to your local RadioShack
store for assistance. To locate your nearest RadioShack, use the store locator
feature at www.radioshack.com, or call 1-800-The Shack (1-800-843-7422) and
follow the menu options. Modifying or tampering with the amplifier's internal
components can cause a malfunction and might invalidate its warranty.
Replacing the Fuse
If the amplifier does not operate, you might need to replace the fuse with
another 7-amp, 250-volt fuse (not supplied).
Fuse Holder Cap
Notes:
· Let the amplifier cool down and see if it starts again before you try
fuse replacement.
· Do not use a fuse with a rating other than that specified here. Doing
so might damage your amplifier.
1. Unplug the amplifier from the AC outlet.
2. Turn the fuse holder cap counterclockwise then pull out the cap to remove
the fuse.
3. If the fuse is blown, replace it. Use only an identical fuse with the proper
rating. The fuse must be 7 amps.
4. Insert the fuse into the fuse holder's socket and press the fuse holder back
into the amplifier. Turn the fuse holder's cap clockwise to tighten it.
20
Additional Information
Troubleshooting
Problem Cause Solution
Why isn't my The device may have Turn your amplifier off. Wait until it
amplifier powering overheated. cools down and try again.
up, even though I
The fuse might be blown. Check the amplifier's fuse and
have tried turning
replace it if necessary.
it on and off?
The speakers might not be Check all connections.
connected properly.
Why can't I hear The amplifier's LEFT and RIGHT Adjust the volume control to the
anything? VOLUME, MIC1, MIC2, MIC3, desired setting.
MIC4/PHONO, or CD/AUX
controls might be on their
minimum settings.
The speakers might not be Check all connections.
connected properly.
A microphone or cable might Check all microphones and cables.
be faulty.
The speakers might be the Make sure your speaker wires are
wrong impedance for the PA. 18-gauge [for wire length up to
7.6 m (25 ft)]. For best results, use
the shortest length of speaker wire
possible.
The amplifier might have shut Turn the amplifier off and let it cool
down. down. Make sure the amplifier is
properly vented, then turn it back
on.
Why am I hearing The FEEDBACK FILTER might Turn the FEEDBACK FILTER
feedback? need to be adjusted. clockwise until you reduce or
eliminate feedback.
Your microphones or speakers Reposition the microphones and
could be too close together. speakers.
21
Additional Information
Specifications
Input Impedance ............................................................................................................ 20k Ohms
Continuous Output Power
Stereo at 1 kHz .........................................................................................125 Watts × 2 (8 Ohms)
Stereo at 1 kHz..........................................................................................175 Watts × 2 (4 Ohms)
Bridged at 20 Hz to 20 kHz ............................................................................ 250 Watts (8 Ohms)
Bridged at 1 kHz ............................................................................................. 350 Watts (8 Ohms)
Total Harmonic Distortion (@ 70 Watts, 8 Ohms, 1 kHz, with Band Pass Filter)
MIC (Phone Jack) ................................................................................................................... 0.20%
MIC (XLR Jack) ....................................................................................................................... 0.20%
CD/AUX .................................................................................................................................. 0.15%
PHONO .................................................................................................................................. 0.20%
Input Sensitivity (at 0.5% THD, 1 kHz)
MIC (Phone Jack) ................................................................................................................1.35 mV
MIC (XLR Jack) ....................................................................................................................1.35 mV
CD/AUX ................................................................................................................................500 mV
PHONO ....................................................................................................................................3 mV
Signal to Noise Ratio (Input Shorted) with WTD
MIC (Phone Jack) ....................................................................................................................65 dB
MIC (XLR Jack) ........................................................................................................................65 dB
CD/AUX ...................................................................................................................................75 dB
PHONO ...................................................................................................................................70 dB
Frequency Response (at 1 Watt, ± 3dB)
MIC (Phone Jack) .................................................................................................... 40 Hz ~ 20 kHz
MIC (XLR Jack) ........................................................................................................ 40 Hz ~ 20 kHz
CD/AUX ................................................................................................................... 20 Hz ~ 30 kHz
PHONO (RIAA 100 Hz/10 kHz).............................................................................. +13dB ~ -14dB
Notch Filter Effect
Range........................................................................................................................ 300 Hz ~ 3kHz
Depth...................................................................................................................................... -12dB
Noise Level (Input Short) ....................................................................................................0.75mV
Speaker Impedance ........................................................................................ A, B (4 ~16 Ohms),
.......................................................................................A+B (8 ~16 Ohms), Bridge (8 ~16 Ohms)
Power Requirement ..............................................................................................120V AC / 60Hz
Power Fuse................................................................................................................7 Amps/250 V
Dimensions.........................................................5 3/8 x 19 x 14 1/2 Inches (136 x 482 x 367 mm)
Weight .....................................................................................................................27 lbs (12.3kgs)
Specifications are subject to change and improvement without notice. Actual product may
vary from the images found in this document.
22
Additional Information
Do More with Your Amplifier
Visit your local RadioShack store or www.radioshack.com to purchase these and
other useful products.
Two-way PA Speaker Audio Mixer
· 3 tweeters 3x7" piezo horn · Separate master and record
tweeter plus two 3x3" piezo outputs
tweeters for sparkling highs · Echo section with delay,
· Great bass response 15" woofer repeat and level controls
with and 50-ounce strontium- · Assignable effect section
ferrite magnet with send and receive level
controls
16-Gauge Cable
· Rope-strand design is more
flexible than standard wire
· Copper conductors, enclosed in
tough plastic insulation with an
embedded stripe for easy
polarity ID
23
Limited Warranty
This product is warranted by RadioShack against manufacturing defects in material and
workmanship under normal use for one (1) year from the date of purchase from RadioShack
company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS
PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED
WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE
NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH
RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR
PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY,
INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may not
apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option,
unless otherwise provided by law: (a) correct the defect by product repair without charge for
parts and labor; (b) replace the product with one of the same or similar design; or (c) refund
the purchase price. All replaced parts and products, and products on which a refund is made,
become the property of RadioShack. New or reconditioned parts and products may be used in
the performance of warranty service. Repaired or replaced parts and products are warranted for
the remainder of the original warranty period. You will be charged for repair or replacement of the
product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation
or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102 12/99
www.radioshack.com
Protect the environment by recycling used electronics. Go to
www.ecyclingcentral.com to find a recycling location near you.
©2008. RadioShack Corporation. 33-2055 A
All rights reserved. RadioShack and RadioShack.com Printed in China
are trademarks used by RadioShack Corporation. 07A08