Text preview for : LG KE600.pdf part of LG KE600 LG Mobile Phone LG KE600 LG KE600.pdf
Back to : LG KE600.pdf | Home
Service Manual
Service Manual
KE600
Model : KE600
Date: October, 2006 / Issue 1.0
REVISED HISTORY
Editor Date Issue Contents of Changes S/W Version
S. H. RYU 2006/07/06 0.1 Initial Release
S. H. RYU 2006/08/24 0.2 The second Release
S. H. RYU 2006/10/16 1.0 Final Release
* The information in this manual is subject to change without notice and should not be construed as a
commitment by LGE Inc. Furthermore, LGE Inc. reserves the right, without notice, to make changes
to equipment design as advances in engineering and manufacturing methods warrant.
* This manual provides the information necessary to install, program, operate and maintain the
KE600/KE608.
-3-
-4-
Table Of Contents
1. INTRODUCTION ...............................7 5. Trouble shooting............................76
1.1 Purpose .................................................. 7 5.1 Trouble shooting test setup....................76
1.2 Regulatory Information............................ 7 5.2 Power on Trouble...................................76
1.3 ABBREVIATION ..................................... 9 5.3 Charging trouble ....................................80
5.4 LCD display trouble................................82
2. PERFORMANCE .............................11 5.5 Camera Trouble .....................................83
2.1 H/W Features.........................................11 5.6 Speaker trouble......................................86
2.2 Technical specification...........................12 5.7 Receiver trouble.....................................88
5.8 Microphone trouble ................................90
3. TECHNICAL BRIEF ........................19
5.9 Vibrator trouble ......................................92
3.1 KE600 / KE608 Component 5.10 Keypad back light trouble.....................94
Block diagram. .......................................19
5.11 SIM card trouble...................................96
3.2 Baseband Processor (BBP)
Introduction ............................................21 5.12 MicroSD trouble ...................................98
3.3 Power management IC ..........................33 5.13 Bluetooth trouble..................................99
3.4 Power ON/OFF ......................................39 5.14 FM Radio trouble ...............................101
3.5 SIM interface..........................................40 5.13 RF PART TROUBLESHOOTING ......103
3.6 Memory ..................................................41
6. Download & S/W upgrade...............116
3.7 LCD Display ...........................................42
6.1 S/W download setup ............................116
3.8 Keypad Switching & Scanning ...............43
6.2 Download program user guide.............117
3.9 Keypad back-light illumination ...............44
3.10 LCD back light illumination...................46 7. CIRCUIT DIAGRAM ......................121
3.11 Battery current consumption monitor ...48
3.12 JTAG & ETM interface connector ........48 8. PCB LAYOUT ................................127
3.13 Audio....................................................49
3.14 USB charging circuit ............................52 9. RF Calibration ..............................133
3.15 FM radio with RDS function .................53 9.1 Test Equipment Setup .........................133
3.16 BLUETOOTH .......................................54 9.2 Calibration Steps..................................133
3.17 Micro SD external memory card slot....58
3.18 12pin Multi Media Interface connector .60 10. Stand-alone Test ........................139
3.19 General Description .............................62
11. ENGINEERING MODE ................143
3.20 Receiver part........................................64
3.21 Transmitter part....................................64
12. EXPLODED VIEW &
3.22 RF synthesizer .....................................66
REPLACEMENT PART LIST ..... 145
3.23 VCTCXO ..............................................66
12.1 Exploded View .................................. 145
3.24 Front End Module control.....................67
3.25 Power Amplifier Module .......................67 12.2 Replacement Parts ............................147
3.26 Dual Mode Operation...........................68 12.3 Accessory ......................................... 167
4. PCB layout......................................69
4.1 Main & Sub PCB component
placement ..............................................69
-5-
-6-
1. INTRODUCTION
1. INTRODUCTION
1.1 Purpose
This manual provides the information necessary to repair, calibration, description and download the
features of the KE600/KE608.
1.2. Regulatory Information
A. Security
Toll fraud, the unauthorized use of telecommunications system by an unauthorized part (for example,
persons other than your company's employees, agents, subcontractors, or person working on your
company's behalf) can result in substantial additional charges you're your telecommunications
services. System users are responsible for the security of own system. There are may be risks of toll
fraud associated with your telecommunications system. System users are responsible for
programming and configuring the equipment to prevent unauthorized use. LGE does not warrant that
this product is immune from the above case but will prevent unauthorized use of common-carrier
telecommunication service of facilities accessed through or connected to it. LGE will not be
responsible for any charges that result from such unauthorized use.
B. Incidence of Harm
If a telephone company determines that the equipment provided to customer is faulty and possibly
causing harm or interruption in service to the telephone network, it should disconnect telephone
service until repair can be done. A telephone company may temporarily disconnect service as long as
repair is not done.
C. Changes in Service
A local telephone company may make changes in its communications facilities or procedure. If these
changes could reasonably be expected to affect the use of the KE600/KE608 or compatibility with the
network, the telephone company is required to give advanced written notice to the user, allowing the
user to take appropriate steps to maintain telephone service.
D. Maintenance Limitations
Maintenance limitations on the KE600/KE608 must be performed only at the LGE or its authorized
agents. The user may not make any changes and/or repairs expect as specifically noted in this
manual. Therefore, note that unauthorized alternations or repair may affect the regulatory status of the
system and may void any remaining warranty.
-7-
1. INTRODUCTION
E. Notice of Radiated Emissions
The KE600/KE608 complies with rules regarding radiation and radio frequency emission as defined by
local regulatory agencies. In accordance with these agencies, you may be required to provide
information such as the following to the end user.
F. Pictures
The pictures in this manual are for illustrative purposes only; your actual hardware may look slightly
different.
G. Interference and Attenuation
An KE600/KE608 may interfere with sensitive laboratory equipment, medical equipment, etc.
Interference from unsuppressed engines or electric motors may cause problems.
H. Electrostatic Sensitive Devices
ATTENTION
Boards, which contains Electrostatic Sensitive Device(ESD), are indicated by the sign.
Following information is ESD handling: Service personnel should ground themselves by using a wrist
strap when exchange system boards.
When repairs are made to a system board, they should spread the floor with anti-static mat which is
also grounded. Use a suitable, grounded soldering iron. Keep sensitive parts in these protective
packages until these are used. When returning system boards or parts such as EEPROM to the
factory, use the protective package as described.
-8-
1. INTRODUCTION
1.3 ABBREVIATION
For the purposes of this manual, following abbreviations apply:
APC Automatic Power Control
BB Baseband
BER Bit Error Ratio
CC-CV Constant Current - Constant Voltage
CLA Cigar Lighter Adapter
DAC Digital to Analog Converter
DCS Digital Communication System
dBm dB relative to 1 milli-watt
DSP Digital Signal Processing
EEPROM Electrical Erasable Programmable Read-Only Memory
EGPRS Enhanced General Packet Radio Service
EL Electroluminescence
ESD Electrostatic Discharge
FPCB Flexible Printed Circuit Board
GMSK Gaussian Minimum Shift Keying
GPIB General Purpose Interface Bus
GPRS General Packet Radio Service
GSM Global System for Mobile Communications
IPUI International Portable User Identity
IF Intermediate Frequency
LCD Liquid Crystal Display
LDO Low Drop Output
LED Light Emitting Diode
-9-
1. INTRODUCTION
LGE LG Electronics
OPLL Offset Phase Locked Loop
PAM Power Amplifier Module
PCB Printed Circuit Board
PGA Programmable Gain Amplifier
PLL Phase Locked Loop
PSTN Public Switched Telephone Network
RF Radio Frequency
RLR Receiving Loudness Rating
RMS Root Mean Square
RTC Real Time Clock
SAW Surface Acoustic Wave
SIM Subscriber Identity Module
SLR Sending Loudness Rating
SRAM Static Random Access Memory
STMR Side Tone Masking Rating
TA Travel Adapter
TDD Time Division Duplex
TDMA Time Division Multiple Access
UART Universal Asynchronous Receiver/Transmitter
VCO Voltage Controlled Oscillator
VCTCXO Voltage Control Temperature Compensated Crystal Oscillator
WAP Wireless Application Protocol
8PSK 8 Phase Shift Keying
- 10 -
2. PERFORMANCE
2. PERFORMANCE
2.1 H/W Feature
Item Feature Comment
Li-Poly, 950mAh
Standard Battery Battery
Size :36.50(W)x58.50(H)x3.65(T)[mm]
AVG TCVR Current 280mA PL5
Standby Current <2.7 mA @PP9
Talk time Up to 3 hours (GSM900,TX Level :5)
Standby time Up to 220 hours (Paging period :9, RSSI: -85dBm )
Charging time Under 3 hours
RX Sensitivity GSM900 : -105dBm, DCS/PCS : -105dBm
GSM900: 32.5dBm (Level 5)
TX output power
DCS/PCS: 29.8dBm (Level 0)
GPRS compatibility Class 10
SIM card type 3V Plug in Type
Display 240 x 320 pixels, 2 inch wide, 262K color, TFT
Soft icons
Key Pad
Status Indicator 0 ~ 9, #, *, Navigation wheel type Key,
Up/Down Side Key, Camera Side key,
END/PWR Key, MP3 Key,
ANT Internal Type
EAR Phone Jack 12pin multi port Headset jack with Remote controller
PC Synchronization Yes
Speech coding HR/EFR/FR/AMR
Data and Fax Yes
Vibrator Yes
Buzzer No
Voice Recoding Yes
C-Mic Yes
Receiver Yes
Travel Adapter Yes
Options Bluetooth hands-free kit, Data Kit
- 11 -
2. PERFORMANCE
2.2 Technical specification
Item Description Specification
GSM900
TX: 890 + 0.2 x n MHz
RX: 935 + 0.2 x n MHz ( n = 1 ~ 124 )
EGSM
1 Frequency Band TX: 890 + 0.2 x (n-1024) MHz
RX: 935 + 0.2 x (n-1024) MHz ( n = 975 ~ 1023 )
DCS1800
TX: 1710 + ( n-511 ) x 0.2 MHz (n = 512 ~ 885)
RX: TX + 95 MHz
PCS1900
TX: 1850.2 + ( n-512 ) x 0.2 MHz (n = 512 ~ 810)
RX: TX + 80MHz
RMS < 5 degrees
2 Phase Error
Peak < 20 degrees
3 Frequency Error < 0.1ppm
GSM900/EGSM
Level Power Toler. Level Power Toler.
5 33 dBm 2dB 13 17 dBm 3dB
6 31 dBm 3dB 14 15 dBm 3dB
7 29 dBm 3dB 15 13 dBm 3dB
8 27 dBm 3dB 16 11 dBm 5dB
9 25 dBm 3dB 17 9 dBm 5dB
10 23 dBm 3dB 18 7 dBm 5dB
11 21 dBm 3dB 19 5 dBm 5dB
4 Power Level 12 19 dBm 3dB
DCS1800/PCS1900
Level Power Toler. Level Power Toler.
0 30 dBm 2dB 8 14 dBm 3dB
1 28 dBm 3dB 9 12 dBm 4dB
2 26 dBm 3dB 10 10 dBm 4dB
3 24 dBm 3dB 11 8 dBm 4dB
4 22 dBm 3dB 12 6 dBm 4dB
5 20 dBm 3dB 13 4 dBm 4dB
6 18 dBm 3dB 14 2 dBm 5dB
7 16 dBm 3dB 15 0 dBm 5dB
- 12 -
2. PERFORMANCE
Item Description Specification
GSM900/EGSM
Offset from Carrier (kHz). Max. dBc
100 +0.5
200 -30
250 -33
400 -60
600~ <1,200 -60
1,200~ <1,800 -60
1,800~ <3,000 -63
3,000~ <6,000 -65
Output RF Spectrum 6,000 -71
5
(due to modulation) DCS1800/PCS1900
Offset from Carrier (kHz). Max. dBc
100 +0.5
200 -30
250 -33
400 -60
600~ <1,200 -60
1,200~ <1,800 -60
1,800~ <3,000 -65
3,000~ <6,000 -65
6,000 -73
GSM900/EGSM
Offset from Carrier (kHz) Max. (dBm)
Output RF Spectrum 400 -19
6
(due to switching transient) 600 -21
1,200 -21
1,800 -24
- 13 -
2. PERFORMANCE
Item Description Specification
DCS1800/PCS1900
Offset from Carrier (kHz). Max. (dBm)
Output RF Spectrum 400 -22
6
(due to switching transient) 600 -24
1,200 -24
1,800 -27
7 Spurious Emissions Conduction, Emission Status
GSM900/EGSM
BER (Class II) < 2.439% @-102dBm
8 Bit Error Ratio
DCS1800/PCS1900
BER (Class II) < 2.439% @-100dBm
9 Rx Level Report accuracy 3 dB
10 SLR 8 3 dB
Frequency (Hz) Max.(dB) Min.(dB)
100 -12 -
200 0 -
300 0 -12
11 Sending Response 1,000 0 -6
2,000 4 -6
3,000 4 -6
3,400 4 -9
4,000 0 -
12 RLR 2 3 dB
Frequency (Hz) Max.(dB) Min.(dB)
100 -12 -
200 0 -
300 2 -7
500 * -5
13 Receiving Response 1,000 0 -5
3,000 2 -5
3,400 2 -10
4,000 2
* Mean that Adopt a straight line in between 300 Hz
and 1,000 Hz to be Max. level in the range.
- 14 -
2. PERFORMANCE
Item Description Specification
14 STMR 13 5 dB
15 Stability Margin > 6 dB
dB to ARL (dB) Level Ratio (dB)
-35 17.5
-30 22.5
-20 30.7
16 Distortion
-10 33.3
0 33.7
7 31.7
10 25.5
17 Side tone Distortion Three stage distortion < 10%
System frequency
18 2.5ppm
(26 MHz) tolerance
19 32.768KHz tolerance 30ppm
Standby
20 Power consumption
- Normal 3 mA(@PP9)
GSM900/Lvl 5 (Battery Capacity 950mA):240 min
21 Talk Time
GSM900/Lvl 12(Battery Capacity 950 mA):420 min
Under conditions, at least 200 hours:
1. Brand new and full 950mAh battery
2. Full charge, no receive/send and keep GSM in idle mode.
22 Standby Time
3. Broadcast set off.
4. Signal strength display set at 3 level above.
5. Backlight of phone set off.
At least 65 dB under below conditions:
23 Ringer Volume 1. Ringer set as ringer.
2. Test distance set as 50 cm
Fast Charge : < 600 mA
24 Charge Current
Slow Charge: < 120 mA
Antenna Bar Number Power
5 -85 dBm ~
4 -90 dBm ~ -86 dBm
25 Antenna Display 3 -95 dBm ~ -91 dBm
2 -100 dBm ~ -96 dBm
1 -105 dBm ~ -101 dBm
0 ~ -105 dBm
- 15 -
2. PERFORMANCE
Item Description Specification
Battery Bar Number Voltage( 0.05V)
4 3.86V~4.2V
26 Battery Indicator 3 3.75V~3.85V
2 3.75V~3.69V
1 3.69V~3.58V
0 3.58V~
3.58V 0.05V (Call)
27 Low Voltage Warning
3.50V 0.05V (Standby)
28 Forced shut down Voltage 3.35 0.05 V
Li-ion Battery
Standard Voltage = 3.7 V
29 Battery Type
Battery full charge voltage = 4.2 V
Capacity: 950mAh
Switching-mode charger
30 Travel Charger Input: 100 ~ 240 V, 50/60Hz
Out put: 5.2, 0.8A
- 16 -
2. PERFORMANCE
* EDGE RF Specification (Option: KE608 is not serviced for "EDGE mode")
Item Description Specification
1 RMS EVM 9%
2 Peak EVM 30%
3 95th Percentile EVM 15%
4 Origin Offset Suppression 30dB
GSM900/EGSM
Level Power Toler. Level Power Toler.
5 27dBm 3dB 13 17dBm 3dB
6 27dBm 3dB 14 15dBm 3dB
7 27dBm 3dB 15 13dBm 3dB
8 27dBm 3dB 16 11dBm 5dB
9 25dBm 3dB 17 9dBm 5dB
10 23dBm 3dB 18 7dBm 5dB
11 21dBm 3dB 19 5dBm 5dB
5 Power Level 12 19dBm 3dB
DCS1800, PCS1900
Level Power Toler. Level Power Toler.
0 26dBm 3dB 8 14 dBm 3dB
1 26dBm 3dB 9 12 dBm 4dB
2 26dBm 3dB 10 10 dBm 4dB
3 24 dBm 3dB 11 8 dBm 4dB
4 22 dBm 3dB 12 6 dBm 4dB
5 20 dBm 3dB 13 4 dBm 4dB
6 18 dBm 3dB 14 2 dBm 5dB
7 16 dBm 3dB 15 0 dBm 5dB
6 Output RF Spectrum GSM900/EGSM
(due to modulation) Offset from carrier(kHz) Max. dBc
100 +0.5
200 -30
250 -33
400 -54
600~<1,200 -60
1,200~<1,800 -60
1,800~<3,000 -63
3,000~<6,000 -65
6,000 -71
- 17 -
2. PERFORMANCE
Item Description Specification
6 Output RF Spectrum DCS1800, PCS1900
(due to modulation) Offset from carrier(kHz) Max. dBc
100 +0.5
200 -30
250 -33
400 -54
600~<1,200 -60
1,200~<1,800 -60
1,800~<3,000 -63
3,000~<6,000 -65
6,000 -71
7 Output RF Spectrum GSM900/EGSM
(due to switching transient) Offset from carrier(kHz) Max. dBm
400 -23
600 -26
1,200 -27
1,800 --30
DCS1800, PCS1900
Offset from carrier(kHz) Max. dBm
400 -23
600 -26
1,200 -27
1,800 -30
- 18 -
3. TECHNICAL BRIEF
3. TECHNICAL BRIEF
Baseband circuit
3.1 KE600 / KE608 Component Block diagram.
Figure 1 KE600/KE608 Hardware architecture
KE600/KE608 is composed with 3 different PCB part such as main PCB, sub PCB and FPCB.
- 19 -
3. TECHNICAL BRIEF
The functional component arrangement is mentioned below diagram.
Figure 2 KE600/KE608 Functional block diagram
- 20 -
3. TECHNICAL BRIEF
3.2. Baseband Processor (BBP) Introduction
Figure 3. Top level block diagram of the S-GOLD2TM (PMB8876)
3.2.1 General Description
S-GOLD2TM is a GSM/EDGE single chip mixed signal Baseband IC containing all analog and digital
functionality of a cellular radio. Additionally S-GOLD2TM Provides multimedia extensions such as
camera, software MIDI, MP3 sound. It is designed as a single chip solution, integrating the digital and
mixed signal portions of the base band in 0.13um, 1.5V technology.
The chip will fully support the FR, EFR, HR and AMR-NB vocoding.S-GOLD2TM support multi-slot
operation modes HSCSD (up to class 10), GPRS for high speed data application (up to class 12) and
EGPRS (up to class 12) without additional external hardware.
- 21 -
3. TECHNICAL BRIEF
3.2.2. Block Description