Text preview for : S2000-MANUAL.pdf part of Tecsun S-2000 S-2000 TECSUN
FM-stereo/ LW / MW / Shortwave / Aircraft Band Radio
Receiver with SSB (Single Side Band)
OWNER'S MANUAL
Back to : S2000-MANUAL.pdf | Home
TECSUN
www.tecsun.com.cn
RADIOS AUSTRALIA
VER.2 03-2010
TECSUN RADIOS AUSTRALIA
TECSUN RADIO CO., LTD.
24/9 Powells Road, Brookvale, NSW 2100 Australia Ph: +61 2 9939 4377
Email: [email protected] www.tecsunradios.com.au
FEATURES www.tecsunradios.com.au
TECSUN
TECSUN
RADIOS AUSTRALIA Thank you for purchasing TECSUN S-2000 receiver. Its features is shown as below:
MW 522-1620 kHz ( 9k Tuning Step)
n
520-1710 kHz (10k Tuning Step)
S-2000 LW 100-519 kHz
SW 1711-29999 kHz
AIR 118-137 MHz
FM-stereo/ LW / MW / Shortwave / Aircraft Band Radio
FM 87-108 MHz
Receiver with SSB (Single Side Band) 88-108 MHz (America)
76-108 MHz (Japan)
n via Earphones or Headphones.
FM stereo
OWNER'S MANUAL Dual Conversion for LW, MW & SW
n
Single Side Band (SSB) with USB & LSB
n
Auto/Manual Frequency Tuning or Station Memory Tuning or Direct Frequency Key-in
n
Function
Auto Tuning Storage (ATS) Function for FM / MW & LW (5s Pre-listening while Auto
n
Tuning)
1000 Station Memories (100 each for FM, SW, SSB & Air Band; 50 each for MW & LW;
n
500 for Mixed Band)
24 Hrs Clock & Dual Alarm Clock Function (Alarm by either Radio or Buzzer)
n
Sleep Timer Function
n
Extra Long Telescopic Antenna for FM, SW, Air Band.
n
360 Degrees Rotating MW Antenna
n
n or Internal FM / MW Antenna Switch
External
n Attenuation to Enhance Reception.
Antenna
n Control for Quality FM and Air Band Listening.
Squelch
Wide / Narrow Bandwidth Selection
n
n Control Knob
RF Gain
n IF Output Jack for DIY (Synchronous Detection, DSP Demodulator, DRM
455 kHz
Converter)
High Quality Built-in 4" Speaker with Excellent Sound Effect.
n
Line in Socket (can be used as speaker for MP3)
n
n Socket (radio broadcast can be transferred to other device).
Line out
Power Sources: 4D Alkaline Batteries
n
220V AC Power(AC power cord included for Asia market)
6V DC Jack (DC adaptor included for Europe market)
TECSUN RADIOS AUSTRALIA
TECSUN RADIO CO., LTD. Dimensions: 372 x 183 x 153 mm (W x H x D)
n
n 5.95 lbs (2.7 kg)
Weight:
MADE IN CHINA
TABLE OF CONTENTS www.tecsunradios.com.au LCD DISPLAY INDICATION www.tecsunradios.com.au
Page
Signal Strength Attenuation
LCD DISPLAY INDICATION ................................................................................................2 Internal or External aerials
QUICK START........................................................................................................................ 3 INT internal aerials
EXT external aerials
TECSUN S-2000 PRODUCT ASSEMBLY DIAGRAM .......................................................... 4
Sleep: Auto Turn off Timer for Radio
S-2000 QUICK START GUIDE........................................................................................... 5-7
Alarm mode
S-2000 OPERATION MANUAL " " Alarm by radio
POWER SUPPLY.................................................................................................................. 8 " " Alarm by buzzer
LISTEN TO THE RADIO....................................................................................................... 9 PAGE: Memory Page PRESET: Memory Address
STORING FREQUENCIES INTO MEMORY................................................................. 10~11 Shortwave Meter Band
Alarm Time
LISTENING TO WHAT'S STORED...................................................................................... 12
DELETE MEMORY.............................................................................................................. 13
4 Digits (small size)
OFF status: to display the alarm time or system
CLOCK SETTING............................................................................................................... 14 code
ALARM SETTING......................................................................................................... 14-15 ON status: to display the time, memory page
and address, SW meter band,
SLEEP TIMER..................................................................................................................... 16 alarm time counter down
USING THE LIGHT BUTTON............................................................................................. 17 SLEEP
BW (BANDWIDTH) BUTTON.............................................................................................. 17
FM ST. (FM STEREO) BUTTON......................................................................................... 17
SW METER BAND SELECTION......................................................................................... 17
TUNING STEP.................................................................................................................... 18
LOCK THE TUNING KNOB................................................................................................ 18
RESET BUTTON................................................................................................................ 18 Single Side Band
SSB (SINGLE SIDE BAND) TUNING................................................................................. 18 USB: Upper Side Band
LSB: Lower Side Band
LINE OUT SOCKETS......................................................................................................... 19 IF Bandwidth
LINE-IN SOCKET............................................................................................................... 19 NARROW: narrow bandwidth
WIDE: wide bandwidth
455kHZ AM IF OUTLET...................................................................................................... 19
kHz: frequency of MW, LW, SW
ANTENNA ATEENUATOR (ANT. ATT.) BUTTON............................................................. 20 MHz: frequency of FM, Air Band
RF GAIN CONTROL........................................................................................................... 20 Battery Meter
" " Full capacity
SQUELCH CONTROL........................................................................................................ 20 " " Low battery (Replacement is required)
EXTERNAL ANTENNA SOCKETS..................................................................................... 21 Tuning Step
SYSTEM CODE SETTING................................................................................................. 22 " " Fast tuning
" " Fine tuning
CHECK THE SYSTEM CODE SETTING............................................................................ 22
Key Lock
TROUBLESHOOTING........................................................................................................ 23
Band Indication
SPECIFICATIONS.......................................................................................................... 24-25
FM Stereo
MESSAGE ALERT STATUS........................................................................................... 26-28 Master Digits
OFF status: to display the clock or system code
ON status: to display frequency or ERR status
1 2
QUICK START www.tecsunradios.com.au
ROTATABLE MW/LW ANTENNA Telescope Antenna for FM/SW/AIR band
MW
RO /LW
TAT
ABL
E ANT
ENN
A
Pull out the telescope antenna and change its length or direction to get better reception when
MW/LW
ROTATABLE ANTENNA
tuning on FM/SW/AIR band.
POWER
The MW/LW antenna is located at the top of the radio; rotate it for best MW/LW reception. Short press the POWER button to turn on or turn off the radio.
LIGHT/SNOOZE SLEEP Sleep Timer
LIGHT - The sleep timer enables the radio to play any length of time from 1~120 minutes and then turn off
- 3 seconds light on: short press the LIGHT button. automatically .
- Always light on: long press the LIGHT button. - Press the SLEEPbutton to turn on the sleep timer.
SNOOZE Notice that the number of minutes to play appears in the display. While it appears there, keep pressing
When the alarm is activated, press the LIGHT/SNOOZE button to deactivate the timer for 10 minutes. on the SLEEPbutton to adjust the sleep timer in between1 to 120 minutes.
TIME Clock set ANT. ATT Antenna Attenuator
CLOCK SETTING The ANT.ATT button, located on the upper right front of the radio, is used to attenuate a signal.
1. Long press the TIME button, when HOUR is flashing, turn the TUNING knob to adjust RF GAIN Radio Frequency Gain
the hour.
2. Shortly press the TIME button, when MINUTE is flashing then turns the The RF (radio frequency) gain controller is adjusted manually to improve the radio's rejection of
TUNING knob to adjust the minute. interference from adjacent frequencies that may interfere, especially on Shortwave.
3. Press the TIME button to confirm.
* One can set the clock either when the radio is on or off. SQUELCH
Using the squelch control eliminates background noise.
TIMER A ON/OFF Alarm by radio or by buzzer
The alarm time setting is same as the clock setting. After the alarm time is set, SSB BFO Beat Frequency Oscillator
there is one more playing timer (1~90minutes) needs to be adjusted and for BFO stands for Beat Frequency Oscillator. This control knob is used to fine tune a sideband signal.
active the alarm by radio. To turn off the timer, Press the TIMER A ON/OFF
button over and over to deactivate the alarm when " " or " " are disappeared.
TIMER B ON/OFF Alarm by radio or by buzzer NOTE: it will cut off the internal AM antenna
The operation method is as same as TIMER A. when an external AM antenna is connected.
EAR Earphone Socket
- Plug in earphones and headphones using L R
a 3.5 mm (1/8 inch) stereo plug.
LINE IN Line in Socket STEP/FAST-SLOW/LOCK Tuning step/lock ATT. TUNE
The LINE-IN socket is on the lower left front of the radio and allows
MEMORY - Short press SETP/FAST-SLOW/LOCK button: to select
either FAST or SLOW tuning step. External ring type AM antenna Connect to external AM antenna AM antenna tuner
you to route the sound from another device to the TECSUN S-2000. -Turn on the radio and tune to a station that you want
Use a cord with a 3.5 mm (1/8 inch) stereo plug. to store into memory. - Long press SETP/FAST-SLOW/LOCK button: to lock the
-Shortly press the MEMORY button note that PRESET TUNING knob.
BASS / TREBLE / VOLUME Adjusting knobs INT./EXT. antenna select switch
will flash in the right corner of the LCD. TUNING Tuning knob
Press the MEMORY button to confirm it (or it will INT. ANT. Use of internal telescopic antenna
BW Band width selector automatically confirm after 3 seconds). One can use the TUNING knob to adjust the clock, tune EXT. ANT.Use of external antenna
Short press BW button to choose wide or narrow selectivity. This may help to reduce interference for to a station, select a memory address and a memory
0~9 Numeric keys page.
some frequencies. Selecting WIDE, usually results of better audio fidelity, while selecting narrow that INT. ANT. FM
50 ohm FM external antenna
limits the audio fidelity somewhat. - Frequency mode: direct key in a station frequency. ANT.
- Memory mode: direct key in a memory number to listen to what's Up and Down button 50
SW 50 ohm SW external antenna
EXT ANT.
ANT.
SSB Single Side Band stored.
- Frequency mode: short press for a station tuning and long press for Auto tuning. 500
Turn on the radio and go into Shortwave. Press the SSB button and tune in signals on USB, press FM - Memory mode: short press for a recalling of preset and long press for auto GND SW
ANT. 500 ohm high-impedance external SW antenna
the SSB button again to LSB. To return to SW band press the SSB button once more. - Short press FM button: to select FM band. tuning of memory.
FM ST. FM Stereo - Long press FM button: to start FM ATS. PAGE Memory Page Right side
Press the FM ST. button when in the FM band to take the radio in or out of stereo reception mode. MW/LW - Turn on the radio and short press the PAGE button (the address page will Synchronous demodulator, SSB demodulator To the LINE IN sockets
When using speaker to listen FM ST., please turn off FM ST. function for better sound. - Short press MW/LW button: to select MW or LW band. flash in the right corner of the LCD.
- Turn the TUNING knob or use the " / " buttons to select the page Software radio (DSP) demodulator To the LINE IN sockets
DELETE - Long press on MW band: to start MW ATS.
- Long press on LW band: to start LW ATS. that you want go to; shortly press PAGE again to confirm. S-2000 Rear DRM 455/12kHz converter etc To the computer
DELETE ONE MEMORY
SW Short-wave band VM / VF Memory mode/ Frequency mode
-Turn on the radio and press the VM/VF button, causing PAGE and PRESET to appear in the display's 455kHz AM IF OUT
upper right corner. - Short press SW button: to select SW band. VF= Variable-Frequency Oscillator mode, VM= memory mode L R
-Use the numeric keypad, the TUNING knob or the up/down tuning buttons ( / ) to select the - Sequentially press SW button: to select a SW meter band. Short press the VM/VF button to change VM/VF mode.
memory that you want to delete. To delete the memory press the DELETE button and release after a
AIR Aircraft band RESET
"B"sounds, note that " "starts blinking on the LCD, then press DELETE button again to confirm. To an amplifier or a recorder.
Please refer to the TECSUN S-2000 manual for QUICK DELETING and DELETING A PAGE. - Short press AIR button: to select AIR band. Press the RESET only when the radio seems to stop functioning properly.
3
TECSUN S-2000 PRODUCT ASSEMBLY DIAGRAM www.tecsunradios.com.au
6 5 4 3 2 1
7
8
9
10
11
18
12
13
14
15
19
16
17
20
21
22
23 36
1. Battery compartment 19. AM aerial upper cover
35 2. Batteries 20. AM aerial lower cover
34 3. AC power cord compartment 21. Magnetic rod with coil
4. Battery contact springs 22. AM aerial plug
5. Back cabinet 23. Handle fixer
6. 220VAC power cord 24. Handgrip
7. Transformer 25. Handgrip gasket
8. Line out unit 26. Handgrip screw nut
33 9. Line out unit holder 27. Knobs
10. Main PC board 28. Buttons
11. Main board fix holder 29. Speaker grill
12. Control board 30. Plastic ring for signal meter
32
13. Rubber pad for buttons 31. LCD plastic lens
31 14. LCD light guide 32. Front cabinet
30 15. Amplifier board 33. Control board
29 16. Signal strength indicate meter 34. External antenna connect board
28 17. Speaker 35. Plastic cover
27 18. Handle 36. Telescopic antenna
26
Note: Assembly to be matched on the products, color, specifications and data
25
24 are subject to change without notice.
4
S-2000 QUICK START GUIDE
TIME SETTING www.tecsunradios.com.au LISTEN TO THE RADIO www.tecsunradios.com.au
S-2000's clock is in 24 hours format and can be set with the radio on or off. When the radio is 1. Press the POWER button to turn on/off the radio.
turned off, the clock shows in mid-display. When the radio is turned on, the clock shows in the 2. Select FM by pressing the FM button, MW(AM) and LW by pressing the MW/LW button (press it
upper right corner of the LCD. twice for LW), SW by pressing the SW button sequentially until you have selected the desired
meter band (meter band number flashes in the upper right corner of the display) and the Aircraft
To set the clock: band by pressing the AIR button.
1. Press the TIME button with a "B" sound until the hour is flashing. 3. Turn the TUNING knob to your desired radio station.
2. While it's flashing turn the TUNING knob to set the correct number of hours; then press the 4. You can also direct key-in the frequency numbers.
TIME button again with a "BB" sound and the minutes are flashing. 5. Adjust the volume, bass and treble tuning knobs for better sound.
3. While it's flashing turn the TUNING knob to set the correct number of minutes; then press TIME
to confirm, and release it after a long "B--" sounds. Note:
Be sure to fully extend the telescopic antenna when listening to SW, FM and AIR. The swivel AM
Note: antenna is located at the top of the radio; swivel it for best AM (MW/LW) reception.
1. After setting the hour or minutes, you can simply let the flashing number time-out, without
pressing the TIME button to confirm the setting.
ATS (AUTO TUNING STORAGE) for FM, MW / LW
2. You can use the / buttons or direct input the numbers to set the clock.
To automatically store the strongest LW, MW or FM stations into Page 0.
ALARM SETTING To activate the ATS function, turn on the radio and fully extend the antenna, then long press the
FM button with a "B" sound and until the frequency number is running on the display. Notice that
There are two independently programmable alarm timers (TIMER A ON/OFF & TIMER B ON/OFF) page 0 (P0) appears in the display's upper right corner with the presets to the right increasing as
to turn it on and off at the specified time. the band is scanned and frequencies are stored into the memory. Once it is done, turn the
TUNING knob to select those stored stations.
To set for TIMER A ON/OFF:
1. Press the TIMER A ON/OFF button with a "B" sound until you see the alarm hour flashing. While MW/LW ATS is same as the FM ATS.
it's flashing adjust the hour with the TUNING knob and press the TIMER A ON/OFF button with a
"BB" sound. Notice that the alarm minutes are flashing. STORING FREQUENCIES INTO MEMORY
2. While it's flashing adjust the alarm minutes with the TUNING knob and press the TIMER A
ON/OFF button. Notice the sleep timer flashing in the box at the top of the display.
To store a frequency into the next available memory on the page that you've selected, press the
3. While it's flashing turn the TUNING knob to adjust the time that the radio is to play(1~90 minutes).
MEMORY button with a "B" sound. Note that PRESET flashes with the next available memory
4. Press the TIMER A ON/OFF button again to confirm setting, or simply let the flashing number
number. Press the MEMORY button with a long "B --" sound to automatically store it into the next
time-out to confirm it automatically meanwhile with a long "B--" sounds.
available memory or when it stops flashing it's stored into the memory number that was flashing.
5. To set for TIMER B ON/OFF is the same as for TIMER A ON/OFF.
Note: LISTENING TO WHAT'S STORED
Once the alarm is on (by radio or buzzer), only the POWER, SLEEP, LIGHT/SNOOZE, and RESET
buttons can be operated. Press the POWER or SLEEP buttons to turn off the alarm. 1. Turn on the radio and go to the correct page by pressing PAGE and entering it with the numeric
keypad.
Alarm by Buzzer or Radio: 2. Press and release the VM/VF button and notice that the PAGE and PRESET show in the
Press on TIMER A ON/OFF key to select " " in TIMER A section. Now the alarm will be on by display's upper right corner.
buzzer. 3. To go from one memory to another give a quick, short press to either the / tuning buttons,
or use the tuning knob.
Note: 3. To auto-scan memory press one of the / tuning buttons for about 2 seconds and notice
In TIMER A or B section, " " means TIMER is set by radio; " " means TIMER is set by that PRESET flashes. the radio scans form one memory to another, staying on each memory
buzzer, and [ ] means TIMER is off. for about 5 seconds. To stop the scan, give the / tuning button a quick, short press.
5. Moreover, you can also direct enter the address numbers within its page.
5 6
S-2000 OPERATION MANUAL
DELETE MEMORY www.tecsunradios.com.au POWER SUPPLY www.tecsunradios.com.au
1. Delete one memory USING BATTERIES
- Turn on the radio and press the VM/VF button, causing PAGE and PRESET to appear in the
- Open the battery compartment cover and insert
display's upper right corner.
4 x UM 1 (D size) batteries according to the polarity
- Use the numeric keypad, the tuning knob, or the / buttons to select the memory that you
diagram imprinted on the battery compartment floor.
want to delete.
- The S-2000 has a battery power indicator in the
- To delete the memory, press DELETE button with a "B" sound and notice that DEL flashes in the
LCD. Fresh batteries will show a full power level
display. Press the DELETE button again with a long "B --" sound to confirm.
of 3 bars. If the indicator shows one bar or the
sound becomes weak and distorted, replace the
2. Delete a memory page
batteries.
- Turn on the radio and select the page that you want to delete by pressing PAGE, note that PAGE
- The radio will turn off automatically if the batteries
flashes in the display's upper right. While it's flashing use the numeric keypad, the tuning knob
become too weak.
or the / buttons to select the page that you wish to delete.
- Check the batteries periodically for leakage. As a
- Press and release the VM/VF button so that PAGE and PRESET appear in the display's upper
precaution, remove the batteries to prevent possible
corner. If [ - - ] appears above PRESET in the display's upper right corner, the page is already Batteries insertion
leakage if it is to be stored for long periods without
deleted and you don't have to continue.
use.
- Press DELETE for about 3 seconds with a "BB" sound or until starts blinking on the LCD,
press the DELETE button again with a long "B--" sound to confirm.
POWER BY AC (For Asia market)
AUTO SCAN STATION AND PRESET MEMORY Open the AC power cord compartment, pull out the
220V AC cord and plug it into the wall outlet.
D
OR
CC
VA
AUTO SCAN STATION ~2
20
Frequency Time
To auto scan station, turn on the radio and select your desired band.
Long press one of the / buttons with a "B" sound to activate the
Auto Scan function. In Auto Scan the radio scans from one station to
the next, stays on the new station for 5 seconds and then moves on.
You can press any button with a "BB" sound to stop the Auto Scan Frequency status
function.
AUTO SCAN MEMORY Page and Preset
Turn on the radio and press VM/VF with a "BB" sound, then press one Frequency
of the / buttons for about 2 seconds with a "B" sound and notice USING DC ADAPTER (For Europe market)
that PRESET flashes. The radio scans from one memory to another, Connect the adaptor, first to the wall outlet, then to
staying on each memory for about 5 seconds. the S-2000 (Assure the unit is turned off).
D
OR
You can press any button with a "BB" sound to stop Auto Scan and 20
VA
CC
listen to your favorite broadcast. NOTE: ~2
Memory status
- Adapter: DC 6V/350mA, negative polarity
- If there's a power failure with the AC or the AC
adaptor and batteries installed, the batteries will
take over and supply power to the radio.
7 8
LISTEN TO THE RADIO www.tecsunradios.com.au STORING FREQUENCIES INTO MEMORY www.tecsunradios.com.au
Press the POWER button to turn on the radio, select your band by pressing the FM, MW/LW, SW, There are 1000 memories with S-2000. 500 memories fixed within P0 page, and 500 memories
or AIR button. set for other storage space. Please see bellows:
There are three methods to tune in the radio station:
Store Storage space in P0 page Other storage space
USING TUNING KNOB Band 500 MEMORIES
P0 (page) ATS
The TUNING knob can be used to tune stations. Select FAST or SLOW tuning with the STEP
FM 100 10 pages each with 50 memories
button, under the tuning knob. FAST/SLOW tuning is shown in the chart below for each band.
If you want to LOCK the tuning knob press the STEP button for about 3 seconds. Do a quick, SW 100 20 pages each with 25 memories
short press to unlock it. SSB 100 25 pages each with 20 memories
FM MW LW SW AIR SSB AIR 100 50 pages each with 10 memories
FAST 0.1MHz 9/10kHz 9kHz 5kHz 0.025MHz 5kHz MW 50 (See the system setting chart to
SLOW 0.01MHz 1kHz 1kHz 1kHz 0.001MHz 1kHz/BFO 50 change above pages)
LW
Note: Be sure to fully extend the telescopic antenna when listening to SW, FM and AIR. The Memory PAGE 0, noted as 'P0', consists of 500 memories, 100 assigned for FM, SW, SSB and
swivel AM (MW/LW) antenna is located at the top of the radio; swivel it for best AM (MW/LW) Air Band; 50 memories each assigned for MW and LW.
reception. Memory PAGE 1 -10, noted as 'P1', 'P2', etc., consists of 50 memories per page, 500 memories
total. You can also change the pages within the system setting.
USING / BUTTON TUNING
Quick, short, sequential presses of the / buttons enables tuning up or down frequency. A 1) ATS (AUTO TUNING STORAGE)
longer press engages Auto Tuning. During Auto tuning, the radio scans from one station to the One can automatically store the strongest LW, MW or FM stations into its own Page 0.
next, stays on the new station for 5 seconds and then moves on. Turn on the radio and select the band that you want ATS to take place in, either MW/LW or FM.
Press the MW/LW or FM and release after a "B" sounds. Notice that page 0 (P0) appears in the
To stop Auto Tuning, press any key. display's upper right corner with the presets to the right increasing asthe band is scanned and
frequencies are stored into the memory. It will stop when
Frequency changing flashing
ATS finishes with a long "B --" sound and listen to the radio
DIRECT FREQUENCY ENTRY station stored in P0:01.
Use this method when the desired frequency of a radio station is known. MW and SW frequencies Then you can use the TUNING knob or the / buttons
are entered in kilohertz (kHz), e.g. 567 kHz or 15100 kHz; FM and AIR frequencies are entered in to select and listen to what's stored.
megahertz (MHz), e.g. 100.8 MHz, ignoring the decimal point. Use the numeric keypad to enter
the frequency directly. Note:
Some noise-stations and blank-stations may also store into page 0 during ATS process
cause by the interference. Please try the ATS again by lower down the telescopic
Note: antenna for FM stations or rotate the MW/LW antenna for MW & LW stations or press ANT.
- No need to enter decimal point for FM and Air Band when input the frequency numbers. For ATT. button to lower the ATT. (dB) level.
example, FM 89.0 MHz, Just ENTER 8 9 0 or FM 104.0 MHz, ENTER 1 0 4 0. (or press 8 9
ENTER, and 1 0 4 ENTER). If the interference is very bad for ATS, please change to manual storage.
- For SW band in between 1711~2999kHz, simply input the frequency number then press ENTER
to confirm. For example, SW 2650kHz, just input 2650 ENTER . If SW frequency in between
3000~29999kHz, just input the numbers directly (no need to press the ENTER button to confirm). 2) MANUAL STORAGE
- For any mis-typed number, simply press DELETE button to cancel it. To manually store a frequency into a memory, turn on the radio and tune to a station that you
- will appear on the display, when entering any outbound frequency. want to store into memory, then long press the MEMORY button / short press it twice / or
short press it and wait for 3 seconds until a long B sound to confirm it.
9 10
www.tecsunradios.com.au LISTENING TO WHAT'S STORED www.tecsunradios.com.au
- Turn on the radio and go to the correct page by pressing PAGE and entering it with the numeric
3) AUTO SCAN (QUICK) STORAGE
keypad or using the TUNING knob or / button.
- Press and release the VM/VF button with a "B" sound and notice the time shows in the upper PAGE / PRESET
right corner of display.
- Press and release the VM/VF button with a "BB" sound and
- Press / buttons for about 2 seconds, a "B" will sound,
notice that the PAGE and PRESET show in the display's
and the radio scans from one station to another, staying on Frequency changing flashing
upper right corner.
each station for about 5 seconds. Quick press the MEMORY
button with a long "B --" sound to store your desired station
before the frequency running to the next available station.
- To go from one memory to another give a quick, short press
To stop the scan, press any buttons except the MEMORY
to either the / button, or rotate the TUNING knob.
button.
flashing
Note: This function is not available for Air Band and SW SSB.
- To auto-scan memory press one of the / buttons for PRESET changing
about 2 seconds with a "B" sound and notice that
flashes in the upper right corner. The radio scans from one
4) STORE A STAION INTO ANOTHER PAGE
memory to another, staying on each memory for about 5
To store a frequency into a memory in another page, first choose the page, then the memory
seconds. To stop the scan, short press any button with a
location and then store the frequency.
"B" sound.
- Turn on the radio and tune to your desired station.
flashing
- Shortly press the MEMORY button with a "B" sound, note
To go to a memory you already know, direct key in two digits of the memory location.
that PRESET will flash in the right cor