РУБИН 37M10-6,M10-7,55FM10-4,FM10-6,FM10-7SM10-4,SM10-6,SM10-7 шасси KD-035.pdf part of Rubin РУБИН 37M10-6,M10-7,55FM10-4,FM10-6,FM10-7SM10-4,SM10-6,SM10-7 шасси KD-035 РУБИН 37M10-6,M10-7,55FM10-4,FM10-6,FM10-7SM10-4,SM10-6,SM10-7 шасси KD-035.pdf, . Rare and Ancient Equipment Rubin TV Телевизор ЭЛТ Рубин 37M10 & 51M10 & 55M10 РУБИН 37M10,51M10,55M10 РУБИН 37M10-6,M10-7,55FM10-4,FM10-6,FM10-7SM10-4,SM10-6,SM10-7 шасси KD-035.pdf text manual preview

Text preview for : РУБИН 37M10-6,M10-7,55FM10-4,FM10-6,FM10-7SM10-4,SM10-6,SM10-7 шасси KD-035.pdf part of Rubin РУБИН 37M10-6,M10-7,55FM10-4,FM10-6,FM10-7SM10-4,SM10-6,SM10-7 шасси KD-035 . Rare and Ancient Equipment Rubin TV Телевизор ЭЛТ Рубин 37M10 & 51M10 & 55M10 РУБИН 37M10,51M10,55M10 РУБИН 37M10-6,M10-7,55FM10-4,FM10-6,FM10-7SM10-4,SM10-6,SM10-7 шасси KD-035.pdf

Back to : РУБИН 37M10-6,M10-7,55FM1 | Home

SERVICE MANUAL for UOC TOP model ( Date: 2008-5-1 )
37M10-6/37M10-7/55FM10-4/55FM10-6/55FM10-7/55SM10-4/55SM10-6/55SM10-7

( 1 ) Specifications & feature:
1. AC Power supply : 170~240V, 50/60Hz
2. Remote hand set battery: 3V ( AAA x 2pcs )
3. TV system RF input: PAL SECAM BG/DK , Video input: PAL/SECAM/NTSC 3.58/NTSC 4.43
4. Receiving channels : VHF-L, VHF-H, UHF
5. Program number : 200
6. Intermediate frequency ( Picture ): 38.9MHz
7. Horizontal frequency: 15625/15750 Hz, Vertical frequency : 50/60 Hz
8. Audio output power : 3W/ 8 ohm ( 2pcs 16 ohm speaker in parallel )
9. Side AV x 1 ( RCA socket )
10. Scart x 1 ( rear )
11. OSD language : English , Russian

( 2 ) Adjustment manual:
1. +B voltage adjustment
a). Receive a color bar pattern , set picture to "Standard Mode".
b). Use voltage meter to measure the DV voltage on Capacitor location C551 .
c). Adjust rheostat PR551 to get voltage meter reading as:
=108 8+/- 1V ------ 14"
=112 8+/- 1V -------21" PF
=125 8+/- 1V ------ 21" Slim

2. Service menu adjustment:
a) Enter service menu
Step 1. Set your TV set in TV mode.
Step 2. Press MENU key,digit keys 6,4,8,3 & Call key sequent, then Service manual M0 will
appear on the screen. Direct press 0,1,2 keys to go M0,M1,M2 pages.
b) Use Program + / - to select adjust item, use Volume + / - to set the data.
c) Enter M3 to M9 pages, need go to SETUP SELECT item in M2 page and press Volume+ , mute then 3
to 9 digit keys. Normally M3 to M9 pages do not need adjustment in production line.
d) Press STANDBY key to exit Service manual mode.

( 3 ) Service menu table:
Page Item Description Range Default Remark
PA
NTSC
L
MO TEST.SW Internal test signal 0~2 0 0OFF 1Central line 2:Checker no adjustment need.
V.SLOPE Vertical linearity 063/-31~+32 35 -01 Adjust PAL system first, then NTSC. Need adjust to match with CRT
V.POSI Vertical center 063/-31~+32 36 -01 Adjust PAL system first, then NTSC. Need adjust to match with CRT
V.SIZE Vertiacl size 063/-31~+32 12 +01 Adjust PAL system first, then NTSC. Need adjust to match with CRT
Vertical S curve
V.SC 063/-31~+32 13 +09 Adjust PAL system first, then NTSC. Need adjust to match with CRT
adjustment

Vertical linearity no adjustment need, for Slim model
V.LINE 063/-31~+32 33 -04 Adjust PAL system first, then NTSC.
adjustment only

Vertical over scan no adjustment need, for Slim model
V.SCR 063/-31~+32 32 0 Adjust PAL system first, then NTSC.
adjustment only

H.PHASE Horizontal phase 063/-31~+32 41 +01 Adjust PAL system first, then NTSC. Need adjust to match with CRT
Need adjust to match with CRT, for
EW.W Horization wide adjust 063/-31~+32 53 +02 Adjust PAL system first, then NTSC.
Slim model only
Horizontal pincushion Need adjust to match with CRT, for
EW.PW 063/-31~+32 21 0 Adjust PAL system first, then NTSC.
adjust Slim model only
Need adjust to match with CRT, for
EW.TC Horizontal trapezia adjust 063/-31~+32 24 +04 Adjust PAL system first, then NTSC.
Slim model only
Horizontal top corner Need adjust to match with CRT, for
EW.UCP 063/-31~+32 39 0 Adjust PAL system first, then NTSC.
adjust Slim model only
Horizontal bottom corner Need adjust to match with CRT, for
EW.LCP 063/-31~+32 47 +02 Adjust PAL system first, then NTSC.
adjust Slim model only
Need adjust to match with CRT, for
H.BOW Horizontal bow adjust 063/-31~+32 30 +02 Adjust PAL system first, then NTSC.
Slim model only
Horizontal parallelogram Need adjust to match with CRT, for
H.PAR 063/-31~+32 35 +06 Adjust PAL system first, then NTSC.
adjust Slim model only
Horizontal blanking adj.
H.BLK.SW ON/OFF ON no adjustment need.
On/Off
Left side Hor. Blanking
H.BLK.L 0~15 0 available when H.BLK.SW = ON no adjustment need.
adj.
Right side Hor. Blanking
H.BLK.R 0~15 0 available when H.BLK.SW = ON no adjustment need.
adj.
no adjustment need, for Slim model
V.X Vertical extention 0~63 24
only
RGB/YUV horizontal no adjustment need, for Slim model
RGB HSH 0~63 6
center adjust only
no adjustment need, not for Slim
PROG Program setting 0~199
model.

TV DVD
M1 CL RGB gain setting 015 10 03dB 7: NORMAL 153dB no adjustment need.
BLOC Black level offset 015 10 0:-300mv 8: no offset 15:+300mv no adjustment need.
R.BIA Red cut adj. 063 33 White balance adjustment Need adjust to match with CRT
White balance adjustment ,DVD means
G.BIA Green cut adj. 063 32 -32 Need adjust to match with CRT
component input
B.BIA Blue cut adj. 063 32 White balance adjustment Need adjust to match with CRT
R.DRV Red drive adj. 063 32 White balance adjustment Need adjust to match with CRT
G.DRV Green drive adj. 063 23 White balance adjustment Need adjust to match with CRT
B.DRV Blue drive adj. 063 36 White balance adjustment Need adjust to match with CRT
SUB BRT Sub-brightness adj. 063 20 Need adjust to match with CRT

Select this item then press V+ key ,
horizontal line will appear. Adjust FBT
VSD Stop vertical scran Need adjust to match with CRT
Screen Voltage knob to get a horizontal line
that is in minimum brightness.

0External signal 1Black screen
TEST.S Test signal selection 05 0 2White screen 3Red screen 4Gree no adjustment need.
screen 5Blue screen

PA
NTSC
L

Receive 62dBv RF signal, adjust RF.AGC to
M2 RF.AGC RF AGC adj. 063 20 Need adjustment
set the picture noise just disappear.
OSD.V.PO OSD vertical position
063/0~63 18 16 Adjust PAL system first, then NTSC. no adjustment need.
S adj
OSD.H.PO OSD Horizontal position
063/0~63 15 no adjustment need.
S adj.
Draught screen beginning
CURT.POS 0~2 0 no adjustment need.
position selection
OSD BRT OSD brightness adj. 015 15 no adjustment need.
Select this item and press V+ key for system
SHIPPING Factory initialization no adjustment need.
initialization
Select this item then press V+,mute keys
SETUP
M3 to M9 pages switch 0/1 0 sequent. Then press 3-9 keys to go M3 - M9 For change pages
SELECT
pages.

M3 SUB CONT Sub-contrast adj. 063 63 no adjustment need.
SUB
Sub-color adj. 063 63 no adjustment need.
COLOR
SUB
Sub-sharpness adj. 063 63 no adjustment need.
SHARP
SUB TINT Sub-tint adj. 063 31 no adjustment need.
Cut off voltage range 0:normal range/-270mV) 1:increase
COF 0/1 0 no adjustment need.
setting range (/-450mV)
THAI Thailand OSD select ON/OFF OFF no adjustment need.
VIETNAM Vietnam OSD select ON/OFF OFF no adjustment need.
INDONESI
Indonesian OSD select ON/OFF OFF no adjustment need.
AN
FRENCH French OSD select ON/OFF OFF no adjustment need.
TURKISH Turkish OSD select ON/OFF OFF no adjustment need.
PORTUGU
Portuguese OSD select ON/OFF OFF no adjustment need.
ESE
BULGARI
Bulgarian OSD select ON/OFF OFF no adjustment need.
AN
RUSSIAN Russian OSD select ON/OFF On no adjustment need.
FARSI Farsi OSD select ON/OFF OFF no adjustment need.
ARABIC Arabic OSD select ON/OFF OFF no adjustment need.
RUMANIA
Rumanian OSD select ON/OFF OFF no adjustment need.
N
SPANISH Spanish OSD select ON/OFF OFF no adjustment need.
ITALIAN Italian OSD select ON/OFF OFF no adjustment need.
GERMAN German OSD select ON/OFF OFF no adjustment need.
DUTCH Dutch OSD select ON/OFF OFF no adjustment need.
SWEDISH Swedish OSD select ON/OFF OFF no adjustment need.
NORWEGI
Norwegian OSD select ON/OFF OFF no adjustment need.
AN
HUNGARI
Hungarian OSD select ON/OFF OFF no adjustment need.
AN
POLISH Polish OSD select ON/OFF OFF no adjustment need.
CZECH Czech OSD select ON/OFF OFF no adjustment need.
SLOVENE Slovene OSD select ON/OFF OFF no adjustment need.
CROATIA
Croatian OSD select ON/OFF OFF no adjustment need.
N
MACEDO
Macedonian OSD select ON/OFF OFF no adjustment need.
NIAN
SERBIAN Serbian OSD select ON/OFF OFF no adjustment need.
GREEK Greek OSD select ON/OFF OFF no adjustment need.
KENYA Kenya OSD select ON/OFF OFF no adjustment need.

I system signal output
M4 VAI 0~1 1 0:normal 1increase 12 no adjustment need.
level adj.
0Contrast action first, then brightness
CBS ABL control method 0~1 1 1Contrast and brightness control at the no adjustment need.
same time.
Signal pre-shot , over-
RPA 0~3 2 0 1:1 1 1.5:1 2 2:1 no adjustment need.
shot adj.
Signal pre-shot & over
RPO 0~3 2 0 1:1 1 1:1.3 2 1:1.7 3 1:0.7 no adjustment need.
shot level adjustment
CVBS/Y sync signal
TCI2X 0~1 0 0: 80UA 1:160UA no adjustment need.
clamping current
BKS Black stretch switch ON/OFF ON no adjustment need.
BSD Black stretch level 0~1 1 0:15 IRE 1:30 IRE no adjustment need.
Black area to switch off
AAS 0~3 1 0:12% back ground 1:20% 2:6% 3:8% no adjustment need.
the black stretch
PWL White level peaking limit ON/OFF OFF no adjustment need.
Soft clipping & peak 0:0% above PWL level 1:5% 2:10%
SOC 03 1 no adjustment need.
white level difference 3:OFF
Video level of peak white
PWLDAC 015 5 0: 0.4VBL-WH 15: 0.6VBL-WH no adjustment need.
limitting active
CHSE Color sensitivity setting 03 3 0:-34dB 1:-37dB 2:-41dB 3:-46B no adjustment need.
Available when S-VHS=ON ,UHF BAND=0
S.IDENT S-VIDEO identify switch ON/OFF OFF no adjustment need.
( M9 )
GAME Game selection ON/OFF OFF no adjustment need.
CALENDA
Calendar selection ON/OFF OFF no adjustment need.
R
Tuner IF frequency 38M/38.9M/45.7
M5 IF 38,9 no adjustment need.
setting 5M
0~7:negative compensation 8:Off 9~15:
OIF IF compensation 0~15 8 no adjustment need.
positive compensation
FFI IF PLL fast speed filter 0~1 0 0:Normal 1: Increase no adjustment need.
AGCS AGC SPEED 0~3 2 0: 0.7X 1:NORMAL 2:3X 3:6X no adjustment need.
Crystal loading capacitor
DCXO 0~3 2 no adjustment need.
compensation
0:dependent on noise detector 1:fixed
FSL Vertical sync cut off level 0~1 1 no adjustment need.
slicing level of 60%
Horizontal sync cut off
SSL 0~1 1 0: 50% 1:30% no adjustment need.
level
Group delay
GD 0~1 1 0:OFF 1: ON no adjustment need.
compensation
AKB AKB selection ON/OFF ON no adjustment need.
Increase vertical scan
ON V.A amplitude in power on 0~15 0 available when AKB was on no adjustment need.
mement
Power reset mode after
DFL 0~1 0 0:Soft start 1: normal no adjustment need.
protection
XDT X-ray protection 0~1 0 0:Standby mode 1: normal no adjustment need.
Fixed beam current 0: RGB blanking 1:power off with a fix
FBC 0~1 0 no adjustment need.
switch off beam current.
IFS.RED IF sensitivity 0~1 1 0:normal 1: reduced no adjustment need.
MUTE Mute method in program 0: mute on in program change period 1:
0/1 0 no adjustment need.
MODE change period mute control pin no change.

M6 CLF internal clamping speed 0~1 0 0:Slow 1:fast no adjustment need.
MONO sound band pass
BPB 0~1 0 0:band pass filter on 1:Bypassed no adjustment need.
filter setting
2nd audio band pass filter
BPB2 0~1 1 0:band pass filter on 1:Bypassed no adjustment need.
setting
FM detection bandwidth 0: 100KHZ 1:225KHZ 2:450KHZ
FMWS 0~3 2 no adjustment need.
setting 3:900KHZ
AGN FM detection Gain 0~1 0 0:NORMAL 1:+6dB no adjustment need.
FM detection Gain
AGNE 0~3 0 0:NORMAL 1:+3.8dB 2:-6dB 3:-3dB no adjustment need.
extend
AVL Auto Volume limit. ON/OFF OFF no adjustment need.
LOUDSPEAKER
DSGLS 0~1 0 0:0dB 1:+6dB no adjustment need.
OUTPUT gain
Volume curve 1(set audio
V.P1 0~100 10 no adjustment need.
output level at Vol=1)
Volume curve 2(set audio
V.P25 0~100 50 no adjustment need.
output level at Vol=25)
Volume curve 3(set audio
V.P50 0~100 70 no adjustment need.
output level at Vol=50)
Volume curve 4(set audio
V.P75 0~100 85 no adjustment need.
output level at Vol=75)
V.MAX Max. Volume setting 0~63 52 no adjustment need.
AC power on delay
ON DL 3~16 3 no adjustment need.
timming
OFF DL Standby delay setting 0~7 0 Set to 1 easier for discharge High Voltage no adjustment need.

Brightness gradual
ONOFF 0: off , 1: on . If set to 1, draught screen
change in power on/off 0~1 0 no adjustment need.
MODE inefficacy.
moment

BGDM BANDGAP mode 0~1 0 no adjustment need.

N-JPN/PAL;N-
USA/PAL;PAL
Color decode matrix
M7 MAT MAT;N-JPN PAL MAT no adjustment need.
setting
MAT;N-USA
MAT

ACL Auto color limit 0~1 0 0:OFF 1:ON no adjustment need.
Center frequency of color
CB 0~1 0 0:fsc 1: 1.1*fsc no adjustment need.
band pass filter
color base band delay
BPS 0~1 0 0:delay line on 1:Bypassed no adjustment need.
line
FCO force to color decode on 0~1 0 0:OFF 1:ON no adjustment need.
PAL system Y signal
Y.P 0~15 8 no adjustment need.
delay
SECAM system Y signal
Y.S 0~15 8 no adjustment need.
delay
Delay time =
YD3*160ns+YD2*160ns+YD1*80ns+YD0
NTSC system Y signal
Y.N 0~15 8 *40ns no adjustment need.
delay

Y.AV AV signal Y delay 0~15 8 no adjustment need.
Y.SVHS S-VHS signal Y delay 0~15 8 no adjustment need.
PAL signal PEAKING
PF.P centre frequency & delay 0~3 1 no adjustment need.
setting
SECAM signal
PF.S PEAKING centre 0~3 1 no adjustment need.
frequency & delay setting 0: 2.7MHZ 190ns 1: 3.1MHZ 160ns
NTSC signal PEAKING 2: 3.5MHZ 143ns 3: 4.0MHZ 125ns
PF.N centre frequency & delay 0~3 1 no adjustment need.
setting
AV signal PEAKING
PF.AV centre frequency & delay 0~3 1 no adjustment need.
setting
RGB/YUV signal
RGB HSH 0~63 3 no adjustment need.
Horizontal centre adj.
PHI1 PLL timming
C.PHI.1 selection in draught 0~1 0 0:Slow 1: NORMAL no adjustment need.
screen mode

Standard mode brightness
M8 S.BRT 0~100 75 no adjustment need.
setting
Standard mode contrast
S.CONT 0~100 75 no adjustment need.
setting
Standard mode color
S.COLOR 0~100 60 no adjustment need.
setting
Standard mode sharpness
S.SHARP 0~100 50 no adjustment need.
setting
Dynamic mode
D.BRT 0~100 85 no adjustment need.
brightness setting
Dynamic mode contrast
D.CONT 0~100 90 no adjustment need.
setting
Dynamic mode color
D.COLOR 0~100 70 no adjustment need.
setting
Dynamic mode sharpness
D.SHARP 0~100 50 no adjustment need.
setting
Soft mode brightness
M.BRT 0~100 50 no adjustment need.
setting
Soft mode contrast
M.CONT 0~100 50 no adjustment need.
setting

M.COLOR Soft mode color setting 0~100 50 no adjustment need.

Soft mode sharpness
M.SHARP 0~100 50 no adjustment need.
setting

Brightness setting in whit
W.BRT 0~100 75 no adjustment need.
balance adj. mode
Contrast setting in whit
W.CONT 0~100 75 no adjustment need.
balance adj. mode

Color setting in whit
W.COLOR 0~100 0 no adjustment need.
balance adj. mode

Horizontal line
SC BRT 0~100 50 no adjustment need.
brightness setting

Cool mode white balance
COOL 0~63 8 no adjustment need.
setting

Warm mode white
WARM 0~63 8 no adjustment need.
balance setting

M9 AV2 AV2 selection ON/OFF ON no adjustment need.
SVHS S-VHS selection ON/OFF OFF no adjustment need.
DVD DVD selection ( YUV ) ON/OFF OFF no adjustment need.
EUROPE mode AV
EURO ON/OFF ON no adjustment need.
selection
If off, all channel audio system will be set to
AUTO Auto Audio system
ON/OFF ON the same system as current channel after auto no adjustment need.
SND detection
program process.
BG BG system selection ON/OFF ON no adjustment need.
I I system selection ON/OFF OFF no adjustment need.
M M system selection ON/OFF OFF no adjustment need.
DK DK system selection ON/OFF ON no adjustment need.
Set the first priority ident sound system in
SIF PRI Audio system preset DK/M/BG/I BG no adjustment need.
Auto program process.
0:TV mode, if last memory is standby mode,
POWER
Power on mode selection 0~3 0 keep standby mode. 1:Last memory 2:TV no adjustment need.
RESET
mode 3: Standby mode
Off: mono mode, pin58 is for AUDIO
MONITOR OUT.
Audio balance control
BALANCE ON/OFF OFF On: AV STEREO mode, pin7 is for TV FM no adjustment need.
selection
sound output, through 4052 switch as
MONITOR OUT.
If HALFTONE=ON & MENU BG=ON,
HALFTON
half tone OSD selection ON/OFF ON then OSD = halftone.If HALFTONE=ON & no adjustment need.
E
MENU BG=OFF, then OSD = transparency
If HALFTONE=OFF & MENU BG=ON,
MENU BG OSD background ON/OFF OFF then OSD=opacity no adjustment need.
IR OPT Remote code selection SANYO/NEC SANYO no adjustment need.
Keyboard control
KEY OPT SANYO/MEK SANYO no adjustment need.
selection
0:off 1:up/down draught screen 2:left/right
CURTAIN Draught screen setting 0~2 0 no adjustment need.
draught screen

Display LOGO when
LOGO ON/OFF OFF no adjustment need.
power on
TILT Tilt control ON/OFF OFF no adjustment need.
B.BACK Blue back control ON/OFF ON no adjustment need.
0:Auto search and memory beginning from
current program number.
ASM OPT Auto program mode 0~1 1 no adjustment need.
1:Auto search and memory beginning from
program number 0
UHF
UHF band selection 0~1 0 0:off 1:on , for 3 band tuner no adjustment need.
BAND
FS TUNER VHF
VH For FS tuner only no adjustment need.
frequence range setting
FS TUNER UHF
UHF For FS tuner only. no adjustment need.
freguency range setting
V.MUTE VIDEO MUTE in power if set to 1~7, no draught screen in power off
ON/1~7 ON no adjustment need.
P.OFF off moment moment.
AV output video signal
AV OUT CVBS/IF CVBS no adjustment need.
select
( 4 ) Vertical & Horizontal scanning adjustment:
Receive standard Monoscope pattern signal for PAL system . Enter M0 page of service menu.
a) Adjust V.SLOPE value to get the horizontal line just appear from half bottom shadow.
b) Adjust V.POSI value to get the center horizontal line correspond to CRT vertical center. Horizontal line

c) Adjust V.SIZE value to set 90% of vertical picture full scan content.
d) Adjust H.PHASE value to get the picture horizontal center correspond to CRT horizontal center.
e) Adjust EW.PW value to get picture pincushion distortion in minume level. Shado
f) Adjust EW.TC value to get picture trapezia distortion in minume level. w
g) Adjust EW.BOW value to get picture bow distortion in minume level.
h) Adjust EW.PAR value to get picture parallelogram distortion in minume level.
i) Adjust EW.UCP value to get picture distortion of top corner in minume level.
j) Adjust EW.LCP value to get picture distortion of bottom corner in minume level.
h) Adjust EW.W vlue to set 94% of horizontal picture full scan content.
i) Receive standard Crosshatch pattern signal for NTSC system, and adjust again for NTSC system.

Remark: step e) to h) are only for Slim CRT.

( 5 ) RF AGC adjustment:
Receive 62dBuV +/- 1 dB color bar signaladjust AGC valueAdjust from low to highin M2 page to reduce picture noise to be
just disappeared gradually.

( 6 ) Screen voltage adjustment:
a) Receive Philips pattern
b) Go to VSD item of M1, press Volume + key then the vertical scan will be stop.
c) Adjust FBT Screen Voltage knob to get a horizontal line that is in minimum brightness.
d) Press Volume + or - key again to active vertical scan and Screen voltage adjustment completed

( 7 ) White balance adjustment:

a) Receive gray and white 2 steps signal.
b) Enter M1 page of service menu
c) adjust R.BIA, G.BIA, B.BIA, R.DRV, G.DRV, BDRV items to set a suitable color temperature.

( 8 ) Sub-brightness adjustment:

a) Receive a gray scale signal
b) Enter Service menu M1 page, use Program +/- keys to select SUB BRT item.
C) Use Volum +/- keys to set the darkest step to just turn off the light.

( 3 ) Reference Circuit diagram :

circuit_diagram_ circuit_diagram_
14_21PF.pdf 21slim.pdf

END