Text preview for : SATELLITE 3000 SERIES.pdf part of TOSHIBA SATELLITE 3000 SERIES TOSHIBA Laptop TOSHIBA-ug SATELLITE 3000 SERIES.pdf
Back to : SATELLITE 3000 SERIES.pdf | Home
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
GENERAL INFORMATION
Tools Required for Proper
Disassembly and Reassembly:
1. Phillips screwdriver (Size 0)
2. Phillips Screwdriver (Size 1)
3. Flat head screwdriver (5mm)
4. Hex driver (5mm)
5. Security Torx(Size8)
6. Case Separator
7. ESD Wrist Strap
8. ESD mats
9. Tweezers
Before attempting any of the following procedures,
make sure that the main battery and AC adaptor is
not connected to the unit and the environment in
which you are working on is protected from
Electro-Static Discharge(ESD).
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
TABLE OF CONTENTS:
1. BATTERY PACK REMOVAL
2. OPTIONAL PC CARD REMOVAL
3. MODULAR BAY REMOVAL
4. DVD-ROM/CDR-W DRIVE REMOVAL
5. HDD REMOVAL
6. MEMORY MODULE REMOVAL
7. KEYBOARD REMOVAL
8. CONTROL BOARD REMOVAL
9. COOLING MODULE REMOVAL
10. CPU REMOVAL
11. TOP COVER REMOVAL
12. VIDEO BOARD REMOVAL
13. MODEM BOARD REMOVAL
14. WIRELESS LAN CARD REMOVAL
15. SYSTEM BOARD REMOVAL
16. DISPLAY MASK REMOVAL
17. FL INVERTER AND LCD REMOVAL
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
BATTERY PACK REMOVAL OPTIONAL PC CARD REMOVAL
Battery
release lever
PC card
Battery pack Eject button
1. Turn the computer upside down as shown. 1. Push the eject button to pop it out.
2. Slide the battery release lever in the direction of the 2. Press the eject button and remove the PC card.
arrow.
3. Slide the battery pack forward and lift it out. NOTE: Before removing any PCMCIA device, make
sure it is "STOPPED" in the PC Card Manager.
MODULAR BAY REMOVAL DVD-ROM/CDR-W DRIVE REMOVAL
DVD-ROM/CDR-W connector DVD-ROM/CDR-W
Release
lever
DVD-ROM/CDR-W bracket
M2.5x4 black screws
Select baydevice
1. Turn the computer upside down. 1. Remove four M2.5x4 black screws securing the
2. Slide the release lever in the direction of the arrow. DVD-ROM/CDR-W to the bracket.
3. Pull out the modular bay device in the direction of the 2. Slide the DVD-ROM/CDR-W out of the bracket.
arrow. 3. Disconnect the DVD-ROM/CDR-W connector from
the drive.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
HDD REMOVAL HDD REMOVAL
HDD
M3x4 silver screws bracket
Insulator
HDD connector
HDD assy M2.5x3 black screws
1. Turn the computer upside down. 5. Remove two M3x4 silver screws securing the
2. Remove two M2.5x3 black screws securing HDD bracket to the drive and lift off the bracket.
HDD assembly. 6. Peel off the HDD insulator.
3. Slide the HDD assembly in the direction of the arrow
to disconnect from the system board.
4. Lift the HDD assembly out of the HDD bay.
. MEMORY MODULE REMOVAL
Memory clips
Memory
cover
M2x3 Black screws Memory module
1. Turn the computer upside down. 3. Spread the memory clips securing the memory
2. Remove two M2x3 black screws and remove the module and pull the memory module out of the
memory cover. connector on a 45 degree angle.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
Wireless switch
KEYBOARD REMOVAL
Control board cable
Display
panel JP1
Board
switch
Keyboard
holder
Case separator M2.5x3 silver screws Keyboard holder
1. Open the display panel. 3. Disconnect the control switch/LED board cable
2. Using the case separator, unlatch the keyboard holder from the keyboard holder.
at the top of the keyboard. 4. Remove four M2.5x3 silver screws securing the
keyboard clip.
Note: When reinstalling the keyboard holder, make sure
that the wireless switch is latch properly to the control
switch board switch.
KEYBOARD REMOVAL CONTROL BOARD REMOVAL
Control
switch
board
Keyboard
IPS switch
cable
Keyboard cable M2.5x3 black screws
JP5 JP4
4. Lift out the keyboard and set it as shown above. 1. Remove four M2.5x3 black screws securing the
5 Disconnect the keyboard cable from JP5 and IPS switch control switch board.
cable from JP4 on the video board and lift out the 2. Disconnect the control switch/LED board from JP4
keyboard. on the main PCB.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
COOLING MODULE REMOVAL
M2.5x3 black
screws Heatsink
Heatsink
cover
Silver screws
1. Remove four M2.5x3 brass screws securing the 2. Remove four silver screws securing the heatsink.
heatsink cover. 3. Lift out the heatsink.
CPU REMOVAL TOP COVER REMOVAL
CPU
Open
CPU
lock
Lock
Flat head screwdriver M2.5x3 black screw Cable cover
1. Using a 5mm flat head screw driver, insert the screwdriver 1. Remove one M2.5x3 flat head screw securing the
into the CPU lock slot and turn it counterclockwise. cable cover.
2. Lift out the CPU.
NOTE: In order to properly lock the CPU, a 5mm flat
head screw driver must be used.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
TOP COVER REMOVAL
LCD/FL cable
M2.5x15 silver
flat head
screw
Grey coax
cable
IPS switch cable Black coax cable M2.5x6 black screws
2. Turn the computer right side up and open the display panel. 5. Remove six M2.5x6 black screws
3. Disconnect the following four cables: (four at the back and two at the bottom cover)
- Black and Gray coax cables securing the display assembly.
- IPS switch cable from PJ1 6. Lift out the display assembly.
4. Remove one M2.5x15 silver flat head screws securing
the LCD/FL cable and disconnect the LCD/FL cable.
M2.5x3 black screw
M2.5x6
black screw
M2.5x18
black
screws
M2.5x5
silver
screws
M2.5x14 black screw M2.5x14 torx screw
8. Remove the following 9 screws from the top cover:
7 Remove the following thirteen screws from the bottom - Six M2.5x3 black screws
cover: - One M2.5x14 black screw
- M2.5x6 black screw - One M2.5x14 Torx screw(Size 8)
- M2.5x18 black screws - One M2.5x5 silver screws
9. Unlatch the top cover from the bottom cover.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
VIDEO BOARD REMOVAL MODEM BOARD REMOVAL
JP8 Video board
JP11 System board RJ11 cable Modem board JP13
1. Disconnect the video board from JP8 and JP11 on 1. Disconnect the modem board from JP13 on the
the system board. system board.
2. Disconnect the RJ11 cable from the modem board.
WIRELESS LAN CARD REMOVAL
Mini PCI
Clips
Wireless LAN card
1. Push the Mini PCI slot clips outward and pull the
Wireless LAN card out of the connector on a
30 degree angle.
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
SYSTEM BOARD REMOVAL
Hex screws
Stud
screws
System board
M2.5x4 brass screws Metal shield
1. Remove the following eleven screws securing the 2. Remove four hex screws at the back of the computer
system board: securing the system board.
- 2 M2.5x4 brass screws securing the metal shield 3. Lift out the system board.
- 5 M2.5x4 brass screws securing the HDD shield
- 1 M2.5x4 brass screw on the system board
- 4 stud screws from the CPU socket
TOSHIBA
Tough Enough for Today's World
FIELD REPLACEABLE UNIT DOCUMENTATION
TM
Satellite
3000 Series
14" DISPLAY MASK REMOVAL FL INVERTER AND 14" LCD REMOVAL
LCD module
Latch
Display
mask
LCD
LCD/ Tape
FL cable
Mask seals FL inverter board M2x4 brass screws FL cable
1. Remove two rubber seals at the top corners of the 1. Peel off the tape securing the FL cable.
display assembly and two mask seals at the bottom 2. Remove two M2.5x5 silver screw securing
corners of the display assembly. FL inverter board.
2. Remove four M2.5x5 silver screws securing the display 3. Carefully lift up the FL inverter board and disconnect
mask. the LCD/FL cable from CN1 and the FL cable
3. There are 21 latches securing the display mask. from CN2.
Carefully insert your fingers between the display mask 4. Remove two 2.5x6 black screws securing the LCD
and the LCD module and pry open the latches starting top cover.
from the bottom six latches, to the five latches on the
right and left sides, ending with the top six latches.
M2x3 silver
screws
LCD/FL cable
5. Lay the top cover as shown above.
6. Peel off two capton tapes securing the LCD/FL cable
and disconnect the cable.
7. Remove four M2x3 silver screws securing the LCD
module to the LCD brackets and lift out the module.
NOTE: When you open and close the display assembly
with the top cover off, hold it by the hinges to
prevent the brackets from bending.
TOSHIBA
Tough Enough for Today's World