Text preview for : 3828W5S2643_1.pdf part of LG MP-9482s service manual part1
Back to : mp-9482s SM part1.part1.r | Home
Website: http://www.lgservice.com
LIGHT OVEN "SolarDOM" SERVICE MANUAL
MODEL: MP-9482S
CAUTION
BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SAFETY PRECAUTIONS
This device is to be serviced only by properly qualified service personnel. Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be taken to avoid possible exposure to excessive microwave energy.
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
A) Do not operate or allow the oven to be operated with the door open. B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary; (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse. C) Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections. D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner. E) A microwave leakage check to verify compliance with the Federal Performance Standard should be performed on each oven prior to release to the owner.
CAUTION
MICROWAVE RADIATION
DO NOT BECOME EXPOSED TO RADIATION FROM THE MICROWAVE GENERATOR OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.
CONTENTS
(Page)
SAFETY PRECAUTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Inside front cover SPECIFICATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1 CAUTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1 INSTALLATIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1 OPERATING INSTRUCTIONS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
FEATURES- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1 CONTROL PANEL - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1 OPERATING SEQUENCE- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-2 SCHEMATIC DIAGRAM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3 CIRCUIT DESCRIPTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-4
SERVICE INFORMATION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
TOOLS AND MEASURING INSTRUMENTS - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1 MICROWAVE LEAKAGE TEST - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1 MEASUREMENT OF MICROWAVE POWER OUTPUT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-3 DISASSEMBLY AND ADJUSTMENT - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-3 UPPER & LOWER HEATER- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-7 INTERLOCK CONTINUITY TEST- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-8 COMPONENT TEST PROCEDURE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-9 TROUBLE SHOOTING - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-14
EXPLODED VIEW - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-1 REPLACEMENT PARTS LIST - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7-1 SCHEMATIC DIAGRAM OF P.C.B. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-1
PRINTED CIRCUIT BOARD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-2
P.C.B. PARTS LIST - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-1
SPECIFICATIONS
ITEM
MODEL
Power Requirement
DESCRIPTION
MP-9482S
230 Volts AC 50 Hz Single phase, 3 wire grounded Microwave Grill Combination Convection 1650W Max 2100W Max 2800W 1900W
Power Output Microwave Frequency Magnetron Timer Outside Dimensions Cavity Dimensions Net Weight Shipping weight Control Complement
900 Watts full microwave power (IEC60705) 2450 MHz 2M214 - 240GP 0 ~ 90 min. 527 (W) x 392 (H) x 480 (D) mm 440 (W) x 204 (H) x 420 (D) mm 28 kg 31 kg 1. Microwave Power level: MAX (900W), 600W, 360W, 180W, 90W 2. GRILL 3. Convection: 40°C, 100~250°C 4. SPEED COMBI
5. SPEED AUTO COOK
Nameplate Location
Front Plate
Accessories
Owner's manual & Cook book High rack, Low rack Metal tray
This oven is designed for household use only. It is not recommended for commercial purposes.
1-1
CAUTIONS
Unlike other appliances, the microwave oven is high-voltage and high-current equipment. Though it is free from danger in ordinary use, extreme care should be taken during repair.
· DO NOT operate on a 2-wire extension cord during repair and use. · NEVER TOUCH any oven components or wiring during operation. · BEFORE TOUCHING any parts of the oven, always remove the power plug from the outlet. · For about 30 seconds after the oven stops, an electric charge remains in the high voltage capacitor. When replacing or checking, you must discharge the high voltage capacitor by shorting across the two terminals with an insulated screwdriver.
MICROWAVE RADIATION
Personnel should not be exposed to the microwave energy which may radiate from the magnetron or other microwave generating device if it is improperly used or connection. All input and output microwave connections, waveguide, flange and gasket must be secure never operate the device without a microwave energy absorbing load attached. Never look into an open waveguide or antenna while the device is energized. · Proper operation of the microwave oven requires that the magnetron be assembled to the waveguide and cavity. Never operate the magnetron unless it is properly installed. · Be sure that the magnetron gasket is properly installed around the dome of the tube whenever installing the magnetron.
ANTENNA
Gasket
COOLING FIN FILAMENT TERMINALS MAGNETRON CHASSIS GROUND
MAGNETRON · Remove your watches whenever working close to or replacing the Magnetron. · NEVER operate the oven with no load. · NEVER injure the door seal and front plate of the oven cavity. · NEVER put iron tools on the magnetron. · NEVER put anything into the latch hole and the interlock switches area.
THE OVEN IS TO BE SERVICED ONLY BY PROPERLY QUALIFIED SERVICE PERSONNEL.
2-1
INSTALLATIONS
BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.
INSTALLING
1. Empty the oven and clean inside it with a soft, damp cloth. Check for damage such as misaligned door, damage around the door or dents inside the cavity or on the exterior. 2. Put the oven on a counter, table, or shelf that is strong enough to hold the oven and the food and utensils you put in it. (Use care when handling.) 3. Do not block the vent and the air intake openings. Blocking vent or air intake openings can cause damage to the oven and poor cooking results. Make sure the microwave oven legs are in place to ensure proper air flow. 4. The oven should not be installed in any area where heat and steam are generated, because they may damage the electronic or mechanical parts of the unit. Do not install the oven next to a conventional surface unit or above a conventional wall oven. 5. Use the oven in an ambient temperature less than 104°F(40°C). 6. Place the oven on a sturdy and flat surface at least 10 cm(4 inches) from the wall. 7. Place the oven as far away as possible from TV, RADIO, COMPUTER, etc., to prevent interference. 8. Do not touch the front glass during or after cooking of the Grill and convection and Combination mode. This glass is very hot during heater operating. 9. Do not operate the oven at microwave and combination mode with Grill rack placed in the cavity when the oven is empty.
10cm
EARTHING INSTRUCTIONS
This oven is designed to be used in a fully earthed condition. It is imperative, therefore, to make sure it is properly earthed before servicing
WARNINGTHIS APPLIANCE MUST BE EARTHED
IMPORTANT
The wires in this mains lead are colored in accordance with the following code: Green-and-yellow: Blue: Brown: Earth Neutral Live
As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows. The wire which is colored green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol ( ) or colored green or green-and-yellow. The wire which is colored blue must be connected to the terminal in the plug which is marked with the letter N or colored black. The wire which is colored brown must be connected to the terminal in the plug which is marked with the letter L or colored red.
3-1
OPERATING INSTRUCTIONS
FEATURES
Oven Front Plate Window Door Screen Door Frame Control Panel Deco. Control Panel
Choke Cover Safety Door Lock System
HIGH Rack
LOW Rack
Metal Tray
CONTROL PANEL
Microondes
Gril
Chaleur tournante
Cuisson combinée
Cuisson Automatique
Entrée
Décongélation
Cuisson préférence
Alarme
Annulation
Stop
Quick Start
Start
rapide
!
"
#
$
%
&
'
!
"
1. Display Window: You can show time of day, cooking time, power level and cooking categories. 2. Enter: You can determine the selected cooking category, microwave power level or temperature. 3. Micro: You can select five power level settings. 4. Grill: You can select the grill categories. 5. Conv.: You can select temperature and time of convection. 6. Speed Combi: You can select the combination categories. 7. Speed Auto Cook: Speed auto cook allows you to cook most of your favorite food quickly by selecting the food type and the weight of the food. 8. Dial Knob: · You can set cooking times, temperature, weight and cooking categories. · While cooking with auto and manual function, you can lengthen or shorten the cooking time at any point by turning the dial knob(except defrost mode). 9. Defrost: You can select the food type and the weight of the food.
10. Favorite: The cooking program can be stored in the memory of your oven up to 9 modes(FA-1~FA-9). 11. Clock: You can set the time of day. 12. Stop/Clear: You can stop over and clear all entries except time of day. · Press Stop/Clear Button one time, all icons will be displayed on window in time of day or clear mode. · Press Stop/Clear Button one more time, all icons will be disappeared. 13. Start/Quick Start: · In order to start cooking which is selected, press button one time. · The quick start feature allows you to set 30 seconds intervals of HIGH power cooking with a touch of the quick start button. 14. Icon: You can see all icons by pressing "Stop/Clear" button one time and remove all icons by pressing one more time(all icons will disappear automatically after 15 seconds). Blink will guide to next step for setting while cooking, the icon of the selected cooking mode will be displayed on window.
4-1
OPERATING SEQUENCE
The following is a description of component functions during oven operation.
6. SPEED COMBI COOKING
*Speed combi Categories
Co-1 Grill-1 + Microwave Power Level Grill-2 + Microwave Power Level Grill-3 + Microwave Power Level (Upper+Lower Heater) + Microwave Power Level Convection + Microwave Power Level
1. SETTING THE CLOCK
Stop/Clear Clock Turn Dial Desired hour
Co-2 Co-3 Co-4 Co-5
Turn Dial Desired minute
Start
Grill & Convection & Speed Combi
ex)
2. MICROWAVE COOKING
Stop/ Clear Function MWO Turn Dial Desired power level Turn Dial Desired cooking time Enter
Stop/ Clear
Function Combi-4 Desired power level
Turn Dial Enter Desired convection temp(40ûC, 100ûC~250ûC) Desired cooking time
Enter
Enter
Start
Start
7. DEFROST
Stop/ Function Defrost Clear Turn Dial Desired defrost category Food weight Start
3. MULTI STAGE COOKING (MICROWAVE)
Stage 1
Stop/ Clear Function MWO Turn Dial Desired power level Enter Turn Dial Desired cooking time
8. SPEED COMBI COOK
Stop/ Clear Function Speed cook Turn Dial Desired speed cook category Food weight Start
Stage 2
Function MWO Desired power level Enter Desired cooking time Start
9. SPEED AUTO COOK
Stop/ Clear Function Auto cook Turn Dial Desired auto cook category Food weight Start
4. GRILL COOKING
Stop/ Clear Turn Dial Desired cooking time Function Grill Turn Dial Desired Grill-1,2,3 Enter
10. CHILD LOCK
This oven has a CHILD LOCK feature.
To Set CHILD LOCK
Start Stop/Clear Stop/Clear (Touch and Hold)
*Grill Categories
Grill-1 Grill-2 Grill-3 (Halogen+Ceramic+Sheather) Upper Heater Upper Sheath Heater Lower Sheath Heater
To Cancel CHILD LOCK
Stop/Clear Stop/Clear (Touch and Hold)
5. CONVECTION COOKING
To cook
Stop/ Clear Function Convection Turn Dial Enter Desired convection temp(40ûC, 100ûC~250ûC) Desired cooking time
11. QUICK START
Stop/Clear Start/Quick Start
12. FAVORITE (MEMORY COOK)
To set Stop/Clear Favorite Any mode Favorite (FA-1) To cook Favorite (FA-1) Start
Enter
Start
4-2
SCHEMATIC DIAGRAM
4-3
CIRCUIT DESCRIPTION
GENERAL DETAILS
· The low voltage transformer supplies the necessary voltage to the micom controller when power cord is plugged in. · When the door is closed, the primary switch is ON, the secondary switch is ON, and the monitor switch opens (contact COM and NO). power of oven as POWER LEVEL. (refer to page 1-1) · One complete cycle of relay 4 is 32 seconds.
WHEN THE DOOR IS OPENED DURING COOKING
· Both the primary switch and relay 4 are cut off primary winding voltage of the high voltage transformer. · ON-OFF of relay 4 is coupled electrically with opening and closing of the secondary switch. · When the door is opened, the secondary switch is opened and when the door is closed, the secondary switch is closed. · The cooking time stops counting down. · Relay stops functioning. · As the door is opened, if the contact of primary switch fails to open, the fuse opens due to the large current surge caused by the monitor switch activation, which in turn stops magnetron oscillation.
FUSE PRIMARY SWITCH
WHEN SELECTING COOKING POWER LEVEL AND TIME
· The micom controller memorizes the function you set. · The time you set appears in the display window. · Each indicator light turns on to indicate that the stage has been set.
WHEN TOUCHING THE START BUTTON
· The coil of the relay is energized by the micom controller. · Power input is supplied to the high voltage transformer through the fuse to the primary switch and relay 4. · Turntable rotates.
FUSE PRIMARY SWITCH
L
MONITOR SWITCH H.V. TRANSFORMER
L
MONITOR SWITCH H.V. TRANSFORMER
N
SECONDARY SWITCH
RELAY 4 MICOM CONTROLLER
N
SECONDARY SWITCH
RELAY 4 MICOM CONTROLLER
· The fan motor rotates and cools the magnetron by blowing the air (coming from the intake on the back cover). · The air is also directed into the oven to exhaust the vapor in the oven through the upper plate. · Cooking time starts counting down. · 3.2 volts AC is generated from the filament winding of the high voltage transformer. This 3.2 volts is applied to the magnetron to heat the magnetron filament through two noise-preventing choke coils. · A high voltage of approximately 2100 volts AC is generated in the secondary of the high voltage transformer which is increased by the action of the high voltage diode and charging of the high voltage capacitor. · The negative 4,000 Volts DC is applied to the filament of the magnetron.
WHEN TOUCHING THE START BUTTON WITH THE HEATER COOKING FUNCTION SELECTED
· The contacts of the primary switch and the secondary switch close the circuit. · A.C. voltage is applied to the heater through thermostat as shown by the solid line.
THERMOSTAT
L
L N
G -Y
E
HEATER
N
RELAY 5,6,7
WHEN THE OVEN IS SET AT ANY LEVEL EXCEPT MAXIMUM.
· The micom controller controls the ON-OFF time of relay 4 by the applied signal to vary the average output
· Turntable rotates. · The fan motor rotates. · The air is also directed into the oven to exhaust the vapor in the oven through the base plate and back plate.
4-4
SERVICE INFORMATION
TOOLS AND MEASURING INSTRUMENTS
NECESSARY TOOLS
Tools normally used for TV servicing are sufficient. Standard tools are listed below. · Diagonal pliers · Long nose pliers · Phillips screwdriver · Flat blade screwdriver · Wrench (size 5mm) · Nutdriver (size 5mm) · Adjustable wrench · Soldering iron · Solder · Vinyl insulation tape · Polishing cloth
NECESSARY MEASURING INSTRUMENTS
· TESTER(VOLTS-DC, AC., Ohmmeter) · Microwave survey meter - Holaday HI-1500 HI-1501 - Narda 8100 8200 · Inch scale · 600 cc non conductive material beaker (glass or plastic), inside diameter: approx. 8.5 cm(31/2 in.) · Cylindrical and made of borosilicate glass vessel. max. thickness: 3 mm outside diameter: approx. 190mm height: approx. 90mm · Glass thermometer: 100°C or 212°F (1 deg scale)
MICROWAVE LEAKAGE TEST
CAUTIONS
· Be sure to check microwave leakage prior to servicing the oven if the oven is operative prior to servicing. · The service personnel should inform the manufacture importer, or assembler of any certified oven unit found to have a microwave emission level in excess of 5 mW/cm2 and should repair any unit found to have excessive emission levels at no cost to the owner and should ascertain the cause of the excessive leakage. The service personnel should instruct the owner not to use the unit until the oven has been brought into compliance. · If the oven operates with the door open, the service personnel should: - Tell the user not to operate the oven. - Contact the manufacturer. · The service personnel should check all surface and vent openings for microwave leakage. · Check for microwave leakage after every servicing. The power density of the microwave radiation leakage emitted by the oven should not exceed 4 mW/cm2. Always start measuring of an unknown field to assure safety for operating personnel from radiation leakage.
MEASURING MICROWAVE ENERGY LEAKAGE
· Pour 275±15cc of 20±5°C(68±9°F) water in a beaker which is graduated to 600 cc, and place the beaker on the center of the turntable. · Set the energy leakage monitor to 2,450 MHz and use it following the manufacturer's recommended test procedure to assure correct result. · When measuring the leakage, always use the 2inch (5cm) spacer supplied with the probe. · Operate the oven at its maximum output. · Measure the microwave radiation using and electromagnetic radiation monitor by holding the probe perpendicular to the surface being measured Move probe along shaded area Probe scanning speed Less than 2.5 cm/sec ( 1in/sec)
5-1
MEASUREMENT WITH OUTER CASE REMOVED
· When you replace the magnetron, measure for microwave energy leakage before the outer case is installed and after all necessary components are replaced or adjusted. Special care should be taken in measuring the following parts. (Circled area of below Fig.) - Around the magnetron - The waveguide
NOTES WHEN MEASURING
· Do not exceed meter full scale deflection. · The test probe must be removed no faster than 1 inch/sec (2.5 cm/sec) along the shaded area, otherwise a false reading may result. · The test probe must be held with the grip portion of the handle. A false reading may result if the operator's hand is between the handle and the probe. · When testing near a corner of the door, keep the probe perpendicular to the surface making sure the probe horizontally along the oven surface, this may possibly cause probe damage.
WARNING : AVOID CONTACTING ANY HIGH VOLTAGE PARTS
RECORD KEEPING AND NOTIFICATION AFTER MEASUREMENT
· After adjustment and repair of any microwave energy interruption or microwave energy blocking device, record the measured values for future reference. Also enter the information on the service invoice. · The microwave energy leakage should not be more than 4 mW/cm.sq. after determining that all parts are in good condition, functioning properly and genuine replacement parts which are listed in this manual have been used. · At least once a year, have the electromagnetic energy leakage monitor checked for calibration by its manufacturer.
MEASUREMENT WITH A FULLY ASSEMBLED OVEN
· After all components, including the outer case, are fully assembled, measure for microwave energy leakage around the door viewing window, the exhaust opening, and air inlet openings. · Microwave energy leakage must not exceed the values prescribed below. NOTE: Leakage with the outer case removed less than 5 mW/cm.sq. Leakage for a fully assembled oven (Before the latch switch (primary) is interrupted) with the door in a slightly opened position-less than 2 mW/cm.sq.
5-2
MEASUREMENT OF MICROWAVE POWER OUTPUT
· Microwave power output measurement is made with the oven supplied at its rated voltage and operated at its maximum microwave power setting with a load of (1000 ± 5)g potable water. · The water is contained in a cylindrical borosilicate glass vessel having a maximum material thickness of 3 mm and an outside diameter of approximately 190 mm. · The oven and the empty vessel are at ambient temperature prior to the start of the test. · The initial temperature (±1) of the water is (10±2)°C. It is measured immediately before the water is added to the vessel. After addition of the water to the vessel, the load is immediately placed on the center of the shelf which is in the lowest position and the microwave power switched on. · The time T for the temperature of the water to rise by a value T of (10±2)°K is measured, where T is the time in seconds and T is the temperature rise. The initial and final water temperatures are selected so that the maximum difference between the final water temperature and the ambient temperature is 5°K. · The microwave power output P in watts is calculated from the following formula: P=
4187 X (T) + 0.55 X (T2 - T0) X M T
· T2: Temperature after heating · T0: Temperature of bowl · M: Weight of bowl
is measured while the microwave generator is operating at full power. Magnetron filament heat-up time is not included. · The water is stirred, to equalize temperature throughout the vessel, prior to measuring the final water temperature. · Stirring devices and measuring instruments are selected in order to minimize addition or removal of heat.
WATER LOAD
TURNTABLE
DISASSEMBLY AND ADJUSTMENT
A. OUTER CASE REMOVAL
1) Disconnect the power supply cord from the outlet. 2) Remove the screws from the rear and along side edges of the case. The outer case must be moved backward to be lifted off.
C. CONTROL PANEL ASSEMBLY
1) Disconnect the leadwire from the PCB SUB ASS'Y. 2) Remove the screws for the control bracket and securing the control panel. 3) Remove control panel ASS'Y from the oven by the moving control panel ASS'Y right side.
B. POWER SUPPLY CORD
1) Remove the outer case. 2) Disconnect two terminals, and remove one screw of the earth terminal.
CAUTION: DISCHARGE THE HIGH VOLTAGE CAPACITOR BEFORE SERVICING (refer to page 2-1)
5-3
D. DOOR GROSS ASSEMBLY REMOVAL
1) Disconnect power. 2) Open the door from oven. insert "JIG" into the choke cover hole of door. 3) Lift the door from front cavity. NOTE: 1. After replacing the door, be sure to check that the primary switch, monitor switch, and secondary switch operate normally. 2. After replacing the door, check for microwave energy leakage with a survey meter. Microwave energy must be below the limit of 5 mW/cm2. (with a 275 ml water load) 3. When mounting the door assembly to the oven assembly, be sure to adjust the door assembly parallel to the chassis. Also adjust so the door has no play between the inner door surface and oven frame assembly. If the door assembly is not mounted properly, microwaves may leak from the clearance between the door and the oven.
F. AIR GUIDE ASSEMBLY REMOVAL
1) Remove the screw on the Bracket upper and lift out the Bracket upper. 2) Remove the mounting screw from magnetron, upper chamber and front plate.
G. MAGNETRON REMOVAL
1) Remove controller assembly, Bracket upper and airguide from upper. 2) Disconnect the leadwire from the high voltage & choke filter transformer and Magnetron. 3) Carefully remove the mounting screws holding the magnetron and the wave guide. 4) Remove the magnetron until its dome is clear from the wave guide. NOTE: 1. When removing the magnetron, make sure its dome does not hit any adjacent parts, or it may be damaged. 2. When replacing the magnetron, be sure to install the magnetron gasket in the correct position and be sure that the gasket is in good condition. 3. After replacing the magnetron, check for microwave leakage with a survey meter around the magnetron. Microwave energy must be below the limit of 5 mW/cm2. (With a 275 ml. water load). Make sure that gasket is rigidly attached to the magnetron. To prevent microwave leakage, tighten the mounting screws properly, making sure there is no gap between the waveguide and the magnetron.
Microondes
Gril
Chaleur tournante
Cuisson combinée
Cuisson Automatique
Entrée
Décongélation
Cuisson préférence
Alarme
Annulation
Stop
Quick Start
Start
rapide
JIG JIG
mm 31
15m m
28mm 10mm 5mm
Bracket upper Air-Guide Choke Filter Magnetron
E. HIGH VOLTAGE TRANSFORMER REMOVAL (Refer to page 5-5)
1) Discharge the high voltage capacitor. 2) Disconnect the leadwire from magnetron, choke filter high voltage transformer, and capacitor. 3) Remove the screw holding the high voltage transformer to the Insulator-U.
5-4
H. FAN MOTOR ASSEMBLY REMOVAL
1) Remove controller assembly, air-guide, power cord, latch board-R from upper. 2) Disconnect the leadwire from fan motor, latch board-R and Noise filter. 3) Remove the three screws holding the the upper plate to the oven cavity. 4) Remove the fan motor ASS'Y to the upper plate.
J. REMOVING THE TURNTABLE MOTOR
1) Remove the metal tray. 2) Remove the turntable shaft VERY CAREFULLY. 3) Lay the unit down on its back. 4) Remove the turntable motor cover. The turntable base cover is easily removed by pinching the six parts with a wire cutting. 5) Disconnect the leadwire from the turntable motor terminals. 6) Remove the screw securing the turntable motor to the oven cavity Ass'y. 7) After repairing the motor, rotate the removed turntable motor cover. 8) Fit the turntable motor cover's projecting part to the base plate slit and fasten a screw. NOTE: 1. Remove the wire lead from the turntable motor VERY CAREFULLY. 2. Be sure to grasp the connector, not the wires, when removing.
I. HIGH VOLTAGE CAPACITOR, H.V. FUSE TRANSFORMER AND DIODE REMOVAL
1) Discharge the high voltage capacitor. 2) Disconnect the leadwire from H.V. transformer, MGT, H.V.Fuse and H.V. capacitor. 3) Remove the screw holding the H.V. transformer and remove the high voltage diode earth screw.
H.V. Transformer
H.V.Fuse Fan Motoer Assembly
H.V. Capacitor
BKT H.V.C
H.V. Diode
Wire Leads Turntable Motor
5-5
K. C-MOTOR, THERMISTOR REMOVAL
1) Remove air-guide and controller assembly upper. 2) Disconnect the leadwire from the circulation motor terminal and oven thermostat. 3) Remove the screws of the thermistor, guide assychamber and lift up the guide assy-chamber. 4) Remove a hex nut securing the circulation fan to shaft of the C-motor. 5) Remove screws securing the motor shaft to the guide assy-chamber. 6) Remove hex nut securing the C-motor to the motor shaft.
PCB Holder PCB Sub (Tact S/W) Control Panel
PCB Bracket PCB Sub (Main)
Button
Circulation Motor
Indicate
Thermistor
Oven Thermostat
Deco.
M. INTERLOCK SYSTEM
1) INTERLOCK MECHANISM The door lock mechanism is a device which has been specially designed to eliminate completely microwave activity when the door is opened during cooking and thus to prevent the danger resulting from the microwave leakage. 2) MOUNTING OF THE PRIMARY/MONITOR/ SECONDARY SWITCHES TO THE LATCH BOARD
ADJUSTMENT DIRECTION
L. PCB ASSEMBLY REMOVAL
1) Remove the control panel assembly from the cavity. (Refer to control panel assembly removal on previous page.) 2) Remove screws which hold the PCB SUB ASS'Y to the PCB holder. 3) Remove the PCB holder & PCB Bracket. 4) Remove screws which hold the control panel. 5) Disconnect the flat cable from the PCB SUB ASS'Y and take off the PCB SUB ASS'Y.
Right Left
MONITOR SWITCH
PRIMARY SWITCH SECONDARY SWITCH
3) INSTALLATION AND ADJUSTMENT OF THE LATCH BOARD TO THE OVEN ASSEMBLY · Mount the latch board to the oven assembly. · Adjust the latch board in the arrow direction so that oven door will not have any play in it when the door is closed. · Tighten the mounting screw.
5-6
N. UPPER HEATER REMOVAL
1) Remove the screw securing the air-guide to the upper. 2) Disconnect the leadwire from the sheath heater and main wire connector. 3) Remove the screws of the chamber-U. 4) Remove the chamber-U, air-tunnel-U. 5) Remove the screw securing of the reflector to sheath heater. 6) Remove the sheath heater from reflector. 7) Remove the screw securing of the heater support-F, B to reflector. 8) Remove the heater support-F, B of reflector. 9) Disconnect the leadwire from ceramic heater. 10) Remove the ceramic heater and halogen heater.
O. LOWER HEATER REMOVAL
1) Disconnect the leadwire from the sheath heater. 2) Remove the base plate from cavity. 3) Remove the nuts from the oven cavity of the side. 4) Remove the Gasket, Ring and Heater Bracket. 5) Remove the sheath heater in the oven cavity.
Chamber-U
Ring Gasket Heater Bracket
Air-Tunnel-U
Lower Sheath Heater
Support-B
Upper Sheath Heater
Ceramic Heater Halogen Heater Reflector
Support-F Insulator-U
5-7
INTERLOCK CONTINUITY TEST
WARNING : FOR CONTINUED PROTECTION AGAINST EXCESSIVE RADIATION EMISSION, REPLACE ONLY WITH IDENTICAL REPLACEMENT PARTS.
TYPE NO. SZM-V 16-FA-63 OR VP-533A-OF FOR PRIMARY SWITCH TYPE NO. SZM-V 16-FA-61 OR VP-531A-OF FOR MONITOR SWITCH TYPE NO. SZM-V 16-FA-63 OR VP-533A-OF FOR SECONDARY SWITCH
A. PRIMARY INTERLOCK SWITCH TEST
When the door release button is depressed slowly with the door closed, an audible click should be heard at the same time or successively at intervals. When the button is released slowly, the latches should activate the switches with an audible click. If the latches do not activate the switches when the door is closed, the switches should be a adjusted in accordance with the adjustment procedure. Disconnect the wire lead from the primary switch. Connect the ohmmeter leads to the common (COM) and normally open (NO) terminal of the switch. The meter should indicate an open circuit in the door open condition. When the door is closed, the meter should indicate a closed circuit. When the primary switch operation is abnormal, make the necessary adjustment or replace the switch only with the same type of switch.
B. SECONDARY INTERLOCK SWITCH TEST
Disconnect the wire lead from the secondary switch. Connect the ohmmeter leads to the common (COM) and normally open (NO) terminals of the switch. The meter should indicate a open circuit in the door open condition. When the door is closed, meter should indicate an closed circuit. When the secondary switch operation is abnormal, make the necessary adjustment or replace the switch only with the same type of switch.
C. MONITOR SWITCH TEST
Disconnect the wire lead from the monitor switch. Connect the ohmmeter leads to the common (COM) and normally closed (NC) terminals of the switch. The meter should indicate closed circuit in the door open condition. When the door is closed, meter should indicate an open circuit. When the monitor switch operation is abnormal, replace with the same type of switch. NOTE: After repairing the door or the interlock system, it is necessary to do this continuity test before operating the oven.
RESULTS Door open Door close
COMPONENTS SWITCHES (Wire leads removed)
TEST PROCEDURE Check for continuity of the switch with a Multi-meter
Primary Switch
NO COM
NC
Monitor Switch
COM
Secondary Switch
NO COM
NOTE: After checking for the continuity of switches, make sure that are correctly connected.
5-8
COMPONENT TEST PROCEDURE
CAUTIONS
1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1) 2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER OF WATER IN CONTAINER) IN THE OVEN.
COMPONENTS
HIGH VOLTAGE TRANSFORMER (Wire leads removed)
TEST PROCEDURE
RESULTS
FILAMENT WINDING TERMINAL SECONDARY TERMINAL
PRIMARY TERMINAL
1. Measure the resistance. (Ohm-meter scale: Rx1 and Rx100) · Primary winding · Secondary winding · Filament winding 2. Measure the resistance. (Ohm-meter scale: Rx1000) · Primary winding to ground · Filament winding to ground MAGNETRON (Wire leads removed) 1. Measure the resistance. (Ohm-meter scale: Rx1) · Filament terminal 2. Measure the resistance. (Ohm-meter scale: Rx1000) · Filament to chassis
Approx.: 1.66 ohm Approx.: 99.5 ohm Less than: 1 ohm
Normal: Infinite Normal: Infinite
Normal: Less than 1 ohm
Normal: Infinite
5-9
COMPONENTS
TEST PROCEDURE
Antenna Gasket Chassis
RESULTS
Filament
NOTE: When testing the magnetron, be sure to install the magnetron gasket in the correct position and be sure that the gasket is in good condition. HIGH VOLTAGE CAPACITOR Measure the resistance. (Ohm-meter scale: Rx1000) · Terminal to terminal. Normal: Momentarily indicates several ohms, and then gradually returns to infinite.
Measure the resistance. (Ohm-meter scale: Rx1000) · Terminal to case.
Normal: Infinite.
HIGH VOLTAGE DIODE
Measure the continuity (Forward). (Ohm-meter scale: Rx10000)
Normal: Infinite. Abnormal: Continuity.
NOTE : Some inexpensive meters may indicate infinite resistance in both direction.
Measure the continuity (Reverse). (Ohm-meter scale: Rx10000)
Normal: Continuity. Abnormal: Infinite.
5-10
COMPONENTS
FUSE H.V. FUSE
TEST PROCEDURE
Check for continuity of the fuse with an multi-meter.
RESULTS
Normal Abnormal
NOTE: If the fuse is blown, check the primary, the secondary, and the monitor switches, H.V.D. and H.V.C. before replacing the fuse. If the fuse is blown by improper switch operation replace the defective switch and the fuse at the same time. Replace just the fuse if the switches operate normally. HEATER ELEMENT (Wire leads removed.) Measure the resistance. (Multi-meter scale: Rx1) Normal: · Upper sheath heater: Approx. 47 ohm (230V, 1100W) · Lower sheath heater: Approx. 74 ohm (230V, 700W) · Upper Ceramic heater: Approx. 27 ohm (120V, 500W) · Upper Halogen heater: Approx. 2.7 ohm (120V, 500W) (at 20 ~ 30oC)
Measure the resistance with 500V-100M ohm insulation resistance meter. Normal: more than 0.5 Mohm
NOTE: Make sure heater is fully cooled when tested. MAGNETRON and OVEN THERMOSTAT OVEN Thermostat 0°C~160°C 160°C
M.G.T Thermostat 0°C~Approx.145°C Approx.145°C
5-11
COMPONENTS
Disconnect the 4 pin connector from P.C.B. (Refer to schematic diagram)
TEST PROCEDURE
Check for P.C.B. connector.
RESULTS
Cooking Start OFF
1
2
3
4
RELAY OF P.C.B. (Wire leads removed.) Note: Relay Relay 1: Fan motor Circulation motor Relay 2: Oven lamp Turntable motor Relay 3: P.T.C Relay (Positive Temperature Coefficient) Relay 4: Microwave Relay 5: Up. sheath heater Relay 6: Lo. sheath heater Relay 7: Halogen+Ceramic Heater FAN MOTOR (Wire leads removed)
Cooking Start
OFF
Relay 1,2,3,4,5,6,7
Measure the resistance. (Ohm-meter scale: R x 1)
Normal: Approx. 1.6 ohm Abnormal: Infinite or several ohm.
TURNTABLE MOTOR (Wire leads removed)
Measure the resistance. (Ohm-meter scale: R x 1000)
Normal: Approx. 10~20 kohm Abnormal: Infinite or several ohm.
NOTE : · A MICROWAVE LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY REASON. · MAKE SURE THE WIRE LEADS ARE IN THE CORRECT POSITION. · WHEN REMOVING THE WIRE LEADS FROM THE PARTS, BE SURE TO GRASP THE CONNECTOR, NOT THE WIRES.
5-12
COMPONENTS
CIRCULATION MOTOR (Wire leads removed)
TEST PROCEDURE
Measure the resistance. (Multi-meter scale : R x 1)
RESULTS
Normal : Approx. 165 ohm. Abnormal : Infinite or several ohm.
KEY PCB
Key P.C.B.
1 2 3 4 5 6 7 8 9 10 ~ 18
Main P.C.B
1 2 3 4 5 6 7 8 9 10 ~ 18
Check continuity between switch terminals, by pressing an appropriate pad on key board. The contacts assignment of the respective pads on the key board is as shown left figures.
NOTE : A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS SERVICED FOR ANY REASON. MAKE SURE THE WIRE LEADS ARE CORRECT POSITION. WHEN REMOVING THE WIRE LEAD FROM THE PARTS, BE SURE TO GRASP THE CONNECTOR, NOT THE WIRES.
5-13
TROUBLE SHOOTING
WHEN YOU GET A COMPLAINT FROM YOUR CUSTOMER, EVALUATE THE COMPLAINT CAREFULLY. IF THE FOLLOWING SYMPTOMS APPLY, PLEASE INSTRUCT THE CUSTOMER IN THE PROPER USE OF THE OVEN. THIS CAN ELIMINATE AN UNNECESSARY SERVICE CALL.
CAUTIONS
1. Check grounding before checking for trouble. 2. Be careful of the high voltage circuit. 3. Discharge the high voltage capacitor. (See page 2-1) 4. When checking the continuity of the switches or of the high voltage transformer, disconnect one lead wire from these parts and then check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter. 5. Do not touch any part of the circuitry on the digital programmer circuit since static electric discharge may damage this control panel. Always touch yourself ground while working on this panel to discharge any static charge built up in your body.
CONDITION
The oven does not work.
CAUSE
Inserting many plug into one plug outlet and using them at the same time (causes overloading). The oven plug is not inserted tightly.
REMEDY
Avoid using other electrical appliances when you use the oven.
Insert the oven plug securely.
Output power is too low.
Low AC input voltage.
Use the oven at adequate line voltage. This may not be a defect. It is possible that the food should be cooked for a longer time period. Do not use metallic ware for cooking except where noted in the cooking guide. Do not use any type of cookware with metallic trimming. 1. Wrap the thinner part with aluminum foil. 2. Use plastic wrap or lid. 3. Stir once or twice while cooking soup, cocoa or milk, etc.
Food temperature is too low.
Sparks occurring.
Using metallic ware and allowing it to touch the oven wall. Ceramic ware trimmed in gold or silver powder is used.
Uneven cooking.
Inconsistent intensity of microwave by their characteristics.
5-14
(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.
1. Incomplete segments. · Segment missing. · Partial segment missing. · Digit flickering (NOTE: Slight flickering is normal.) 2. Colon does not turn on or blink. 3. A distinct change in the brightness of one or more numbers in display. 4. One or more digits in the display are not lighting. 5. Display does not count down with time blinking or up with clock operation. 6. Display obviously jumps in time while counting down. 7. Display counts down too fast while cooking. 8. Each indicator light does not turn on after setting cooking cycle. 9. Display time of day does not reappear when cooking is finished. 10. Beep sound is not heard when correct key is touched.
CONDITION
1. No input can be programmed.
CHECK
Check the connection between key assembly and PCB assembly.
RESULT
Continuity.
CAUSE
Defective PCB assembly. Loose connection.
REMEDY
Replace PCB assembly. Connect them tightly.
No continuity.
2. Some inputs cannot be programmed. 3. Display shows a number or figure different from one touched.
Replace key assembly and check operation.
Everything works as specified.
Defective key assembly.
Replace key assembly.
Still have trouble.
Defective PCB assembly.
Replace PCB assembly.
4. Random programming when touching other pads. 5. Display is fixed at some figure and can not accept any input.
5-15
(TROUBLE 2) Oven does not operate at all ; Display window does not display any figures and no input is accepted. CONDITION
1. Fuse blows.
CHECK
Check continuity of monitor switch (with door closed).
RESULT
Continuity.
CAUSE
Malfunction of the monitor switch.
REMEDY
Replace primary and monitor switches.
No continuity.
Replace fuse
Check continuity of primary switch (with door opened).
Continuity.
Shorted contact at the primary switch.
Replace primary and monitor switches.
No continuity.
Disconnect one side of the wire lead connected from transformer to the high voltage capacitor and operate the unit.
Normal.
Defective high voltage capacitor. Defective high voltage transformer.
Replace high voltage capacitor. Replace high voltage transformer.
Fuse blows again
NOTE : All these switches must be replaced at the same time. Refer to page 5-6, 5-8
2. Fuse does not blow.
Check continuity of magnetron thermostat.
No continuity.
Continuity.
Defective magnetron thermostat, oven thermostat and Lower voltage transformer.
Replace magnetron thermostat, oven thermostat and Lower voltage transformer.
Check continuity of power supply cord.
No continuity.
Defective power supply cord.
Replace power supply cord.
5-16
(TROUBLE 3) Display shows all figures set, but oven does not start cooking while desired program times are set and START button is touched. CONDITION
1.Setting time does not count down when touching START button.
CHECK
Check continuity of secondary switch (with door closed).
RESULT
No continuity.
CAUSE
Defective secondary switch and secondary switch wire connector.
REMEDY
Replace secondary switch and secondary switch wire connector.
continuity.
Check the connection between connector and P.C.B assembly.
No continuity.
Defective P.C.B assembly. Loose connection.
Replace P.C.B assembly. Connection then tightly. Replace fan motor, c-motor. Replace fan motor, c-motor.
Continuity. 2. Fan motor, c-motor or oven lamp, turntable motor do not turn on.
Check fan motor, c-motor. Check oven lamp, turntable motor.
Abnormal.
Defective fan motor, c-motor. Defective fan motor, c-motor.
Abnormal. Normal.
(TROUBLE 4) Oven seems to be operation but little heat is produced in oven load. CONDITION
Output is low.
CHECK
Check the power source voltage.
RESULT
Lower than 90% of rating voltage. Normal.
CAUSE
Decrease in power source voltage with load.
REMEDY
Suggest customer contact local electric power utility co. or qualified electrician. Replace P.C.B assembly.
Disconnect the wire leads from relay 4 and check on and off time with multitester.
Abnormal. Normal.
Defective P.C.B assembly.
Measure the output power.
Abnormal.
Defective magnetron.
Replace magnetron.
NOTE: Simple test of power output-conducted by heating one liter water for one min. if available. Minimum 8.5oC temperature rise is normal condition.
5-17
(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run (Display operates properly) CONDITION
No microwave oscillation.
CHECK
Disconnect the wire leads from relay 4 and check continuity of relay 4. (Operate the unit)
RESULT
No continuity.
CAUSE
Defective P.C.B assembly
REMEDY
Replace P.C.B assembly
Continuity.
Check H.V. transformer and H.V. Fuse.
Abnormal
Defective high voltage transformer and H.V. Fuse.
Replace high voltage transformer and H.V. Fuse.
normal
Check H.V. capacitor.
Abnormal
Defective high voltage capacitor.
Replace high voltage capacitor.
normal
Check H.V. diode.
Abnormal
Defective high voltage Diode.
Replace high voltage Diode.
normal
Check Magnetron.
Abnormal
Defective magnetron.
Replace magnetron .
5-18
(TROUBLE 6) Oven does not cook properly when programmed for the set power level (Operates properly on HIGH) CONDITION
Output is full when you set lower power level.
CHECK
Disconnect the wire leads from relay 4 and check continuity relay 4. (Operate the unit)
RESULT
Abnormal.
CAUSE
Defective P.C.B. assembly.
REMEDY
Replace P.C.B. assembly.
(TROUBLE 7) Heater
Relay 5- Up. sheath Heater Relay 6- Lo. sheath Heater Relay 7- Halogen + Ceramic Heater RESULT
Abnormal.
CONDITION
1. Heater is not operating.
CHECK
Heater.
CAUSE
Malfunction of the heater.
REMEDY
Replace.
Normal.
Thermostat and relay 5, 6, 7.
Abnormal.
Malfunction of the thermostat and relay 5,6,7
Replace.
Normal. Replace or connect tightly.
Wire connection.
No continuity.
Open or loosen.
2. Lower temperature the oven.
Heater.
Abnormal.
Malfunction of the heater.
Replace.
Normal.
Thermostat and relay 5, 6, 7.
Abnormal.
Malfunction of the thermostat and relay 5,6,7
Replace.
NOTE: * Make sure the wire leads correct position. * When removing the wire leads from parts, Be sure to grasp the connector not the wires. * When removing the magnetron, be sure to install the magnetron gasket in the correct position and in good condition.
5-19
EXPLODED VIEW
INTRODUCTION
INTERIOR PARTS
CONTROL PANEL PARTS
OVEN CAVITY PARTS BASE PLATE PARTS LATCH BOARD PARTS
DOOR PARTS
6-1
DOOR PARTS
13581A 13552A 13213A
WTP004 140262 14970A
347752 149702
WPZ001 948501 WPZ001 WTT028 149701
948501 347751 14890A 14970A
140261
WTT028
13720D
13650A
6-2
CONTROL PANEL PARTS
WTT028 24781M 268711 WTT028
24810P
WTP004 24980A 268712 WTP004 WTP004
250201
249401 24402A 243501 268713 250201
24781A
6-3
OVEN CAVITY PARTS
35026C
WTT021
33112U 35026G
33390M
WNZ015
WTT010
33052M
34370T
34810H
343501 WNZ015
368771
353001 36549S WTP013 63302A
54790A
WTT028 647781 WTT028 63303A 647781
WTT028
6-4
LATCH BOARD PARTS
WSZ085
WSZ085
43501L 466001 43500A 43501A
466001
43500L 466003
44510A
6-5
INTERIOR PARTS (I)
WTT028 WTT028 53504A
35264A 35300A 53035A
35300S
56201B
56324A
53550L 35300H 56912B
WSZ002 WTT021 WTT028 552652 34890C WTT028
350122
WTT021
WTT028
6-6
552651
INTERIOR PARTS (II)
54975A WTT021 WSZ002 56901A
WTP004 56930V
948502
WSZ002 56170D WTT028 56201A WTP002 56549F 56930M 56322A WSZ002 56411A 50CZZH 54810C 350121 33660A WTT021 55900A WWP008 WNH003 WWS005 56851D 36549W 36549C 50FZZA WTT021 WTT028 54980A
568771
6-7
SCHEMATIC DIAGRAM OF P.C.B
8-1
PRINTED CIRCUIT BOARD (Key P.C.B.1)
8-2
PRINTED CIRCUIT BOARD (Key P.C.B.2)
8-3
PRINTED CIRCUIT BOARD (Power P.C.B.2)
8-4
P/NO : 3828W5S2643
Dec., 2002 Printed in Korea