Text preview for : 06-tme3-svctool.pdf part of NOKIA 06-tme3-svctool NOKIA Mobile Phone 30 06-tme3-svctool.pdf
Back to : 06-tme3-svctool.pdf | Home
Customer Care Solutions
TME-3 Series Transceivers
Service Tools
Issue 3 10/03 Copyright Nokia. All rights reserved.
TME-3
Service Tools CCS Technical Documentation
[This page intentionally left blank.]
Page 2 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
Table of Contents
Page No
General Instructions ....................................................................................................... 4
XRC-5 RF Cable ..........................................................................................................5
Product code............................................................................................................. 5
JBV-1 Docking Station and MJF-21 Adapter .............................................................6
Product Code:............................................................................................................ 6
Product Code:............................................................................................................ 7
MJF-21 & JBV-1 setup ............................................................................................. 7
FLA-34 Flashing Adapter ............................................................................................8
Product Code ............................................................................................................. 8
FLA-34 setup............................................................................................................. 8
MJS-63 Module Jig ......................................................................................................9
Product Code ............................................................................................................. 9
MJS-63 setup........................................................................................................... 10
MJS-62 Soldering Jig ................................................................................................11
Product Code ........................................................................................................... 11
FPS-8 Flash Prommer (Sales Pack) ...........................................................................12
Sales package code.................................................................................................. 12
ACS-10 Power supply module for FPS-8 ..................................................................13
Product Code ........................................................................................................... 13
FPS-8C Parallel Flash Prommer (Sales Pack) ...........................................................14
Sales package code.................................................................................................. 14
ACF-8 Universal Power Supply ................................................................................15
Product Code ........................................................................................................... 15
AXS-4 Service Cable .................................................................................................16
Product code........................................................................................................... 16
SW Security Device PKD-1 .....................................................................................17
Product Code ........................................................................................................... 17
FLS-4S POS (Point Of Sale) Flash Device (Sales Pack) .........................................18
Product Code ........................................................................................................... 18
POS Flash setup ...................................................................................................... 18
PCS-1 Power Cable ...................................................................................................19
Product Code ........................................................................................................... 19
DAU-9S MBUS Cable ..............................................................................................20
Product Code ........................................................................................................... 20
XCS-4 Modular Cable ...............................................................................................21
Product code........................................................................................................... 21
Parallel Cable CA-10 DS ...........................................................................................22
Product code........................................................................................................... 22
SB-1 Service Box for TME-3 ....................................................................................23
Product code............................................................................................................ 23
DTX-3 Nokia 32 Application module .......................................................................24
Product code............................................................................................................ 24
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 3
TME-3
Service Tools CCS Technical Documentation
General Instructions
Before connecting the service tools :
Caution:Make sure that you have swithed off the PC and the printer before
making connections!
Caution:Do not connect the PKD-1 key to the serial port. You may damage
your PKD-1!
Page 4 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
XRC-5 RF Cable
RF cable XRC-5 is used to connect e.g. Module Jig MJS-63 to RF measurement equip-
ment..
Attenuation table:
900 MHz 0.86dB/m
1800 MHz 1.20dB/m
1900 MHz 1.24dB/m
Product code
XRC-5RF Cable: 0730276
Figure 1: View of XRC-5
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 5
TME-3
Service Tools CCS Technical Documentation
JBV-1 Docking Station and MJF-21 Adapter
The JBV-1 Docking Station has been designed for calibration and software update use.
The MJF-21 Docking Station Adapter makes signal connections to the phone.
JBV-1 and MJF-21 are used as one unit.
In calibration mode JBV-1 is powered by external power supply 11-16VDC. In flashing
operation the power for the phone must be taken from external power supply 11-16VDC.
Product Code:
JBV-1 Docking Station: 0770298
Figure 2: View of JBV-1
Page 6 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
Product Code:
MJF-21 Docking Station Adapter: 0770374
Figure 3: View of MJF-21
MJF-21 & JBV-1 setup
1. Attach the protection key PKD-1 to parallel port one (25-pin female D-connector) of
the PC. When connecting the PKD-1 to the parallel port be sure that you insert the PC
end of the PKD-1 to the PC (male side). If you use a printer on parallel port one, place the
PKD-1 between the PC and your printer cable.
2. Connect the printer cable and D9-D9 cable, AXS-4 to the flash prommer, FPS-8.
3. Attach the docking station adadpter, MJF-21, to the docking station, JBV-1.
4. Connect modular cable, XCS-4, from the front panel of FPS-8 to the docking station,
JBV-1.
5. Connect power cable PCS-1, from the front panel of the FPS-8 (4V) to the connector
of JBV-1.
6. Install the TME-3/4 to the docking station adapter, MJF-21.
7. Connect power supply ACF-8 to the FPS-8.
8. Start Phoenix and follow the flashing instructions.
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 7
TME-3
Service Tools CCS Technical Documentation
FLA-34 Flashing Adapter
The FLA-34 Flashing adapter is used for reflashing the TME-3 in a service center.
Product Code
FLA-34 Flashing Jig: 0770375
Figure 4: View of FLA-34
FLA-34 setup
1. Attach the protection key PKD-1 to parallel port one (25-pin female D-connector) of
the PC. When connecting the PKD-1 to the parallel port be sure that you insert the PC
end of the PKD-1 to the PC (male side). If you use a printer on parallel port one, place the
PKD-1 between the PC and your printer cable.
2. Connect the printer cable and D9-D9 cable, AXS-4 to the flash prommer, FPS-8.
3. Connect modular cable, XCS-4, from the front panel of FPS-8 to the flash adapter,
FLA-34.
4. Connect power cable, PCS-1, from the rear panel of the FPS-8 (ACS-10) or external
power supply (8,5V) to the connector of FLA-34.
5. Install the TME-3/4 to the flash adapter, FLA-34.
6. Connect power supply ACF-8 to the FPS-8.
7. Start Phoenix and follow the flashing instructions.
Page 8 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
MJS-63 Module Jig
The MJS-63 Module Jig is used for testing of system/RF-module.
Product Code
MJS-63 Module Jig: 0770377
Figure 5: View of MJS-63
*Note: The nominal supply voltage for MJS-63 is +8.0 V.
The supply voltage must not exceed +12.0 V (min 5V). (MJS-63 has overvoltage protec-
tion)
For flashing with FPS-8, it is possible to bypass the regulator(jumper).
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 9
TME-3
Service Tools CCS Technical Documentation
MJS-63 setup
1. Attach the protection key PKD-1 to parallel port one (25-pin female D-connector) of
thePC. When connecting the PKD-1 to the parallel port be sure that you insert the PC
end of the PKD-1 to the PC (male side). If you use a printer on parallel port one, place the
PKD-1 between the PC and your printer cable.
2. Connect the printer cable and D9-D9 cable, AXS-4 to the flash prommer, FPS-8.
3. Connect modular cable, XCS-4, from the front panel of FPS-8 to the module jig, MJS-
63.
4. Connect power cable, PCS-1, from the rear panel of the FPS-8 (ACS-10) or external
power supply (8,5V) to the connector of MJS-63.
5. Install the RL7/8 module to the module jig, MJS-63.
6. Connect power supply ACF-8 to the FPS-8.
7. Start Phoenix and follow the flashing instructions.
Page 10 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
MJS-62 Soldering Jig
The Soldering Jig MJS-62 is used for soldering and as a rework jig for system module.
Product Code
MJS-62 Soldering Jig: 0770376
Figure 6: View of MJS-62
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 11
TME-3
Service Tools CCS Technical Documentation
FPS-8 Flash Prommer (Sales Pack)
The Flash Prommer FPS-8 is used with e.g. FLA-63 and JBV-1. Power is supplied to FPS-8
from a ACF-8 type Power Supply. Also refer to ACS-10.
The sales pack includes:
- FPS-8 Flash Prommer 0750123
- FPS-8 Activation Sheet 9359289
- ACF-8 Power Supply 0680032
- AXS-4 Serial Cable (D9-D9) 0730090 (for PC COM port)
- Centronics Cable 0730029 (for PC parallel port)
- CA-10 DS Cable 0730298
- CD-ROM(user guide and installation SW) 0774271
Sales package code
FPS-8 Flash Prommer: 0080321
View of FPS-8 Figure 7: View of FPS-8
Page 12 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
ACS-10 Power supply module for FPS-8
ACS-10 power supply module replaces the original rear panel of the FPS-8. ACS-10 is
needed when programming TME-3.
Installation instructions are included in the FPS-8 Flashing User Guide.
Product Code
ACS-10 Power Supply Module: 0770340
Figure 8: ACS-10 inside
Figure 9: ACS-10 rear panel
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 13
TME-3
Service Tools CCS Technical Documentation
FPS-8C Parallel Flash Prommer (Sales Pack)
The Parallel Flash Prommer FPS-8C is used with MJF-6 and JBV-1. Flash programming
can be done to maximum of 8 phones parallel. FPS-8C consists of eight SF11C program-
ming cards. SF11C card is functionally identical to FPS-8.
Sales package code
FPS-8C Parallel Flash Prommer: 0080396
Figure 10: View of FPS-8C
Page 14 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
ACF-8 Universal Power Supply
ACF-8 Universal Power Supply is used to power FPS-8. ACF-8 has 6 V DC and 2.1 A out-
put.
Product Code
ACF-8 Universal Power Supply: 0680032
Figure 11: View of ACF-8
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 15
TME-3
Service Tools CCS Technical Documentation
AXS-4 Service Cable
The AXS-4 D9-D9 Service Cable is used to connect two 9 pin D connectors e.g. between
PC and FPS-8. Cable length is 2 meters.
Product code
AXS-4 D9-D9 Service Cable: 0730090
Figure 12: View of AXS-4
Page 16 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
SW Security Device PKD-1
SW security device is a piece of hardware enabling the use of the service software when
connected to the parallel (LPT) port of the PC. Whithout the dongle present it is not pos-
sible to use the service software. Printer or any such device can be connected to the PC
through the dongle if needed.
Caution:Make sure that you have switched off the PC and the printer before making connections!
Caution:Do not connected the PKD-1 to the serial port. You may damage your PKD-1!
Product Code
SW Security Device PKD-1: 0750018
Figure 13: View of SW Security Device
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 17
TME-3
Service Tools CCS Technical Documentation
FLS-4S POS (Point Of Sale) Flash Device (Sales Pack)
FLS-4S is a dongle and flash device incorporated into one package, developed specifically
for POS use.
Product Code
Sales Pack - Europe/Africa 0080541
Sales Pack -APAC 0080542
Sales Pack -Americas 0080543
View of FLS-4 Figure 14: View of FLS-4S
POS Flash setup
1. Attach the POS flash adapter FLS-4S to parallel port one (25-pin female D-connector)
of the PC.
2. Connect the modular cable, XCS-4, between the FLS-4S and flash adapter, FLA-34.
3. Connect the power supply ACF-8 to the connector of FLS-4S.
4. Connect the external power supply (8,5V) to the flash adapter, FLA-34.
5. Install the TME-3/4 to the flash adapter, FLA-34.
6. Start Phoenix and follow the flashing instructions.
Page 18 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
PCS-1 Power Cable
The PCS-1 Power Cable (DC) is used to connect e.g. JBV-1 to FPS-8.
Product Code
PCS-1 Power Cable: 0730012
of PCS-1 Figure 15: View of PCS-1
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 19
TME-3
Service Tools CCS Technical Documentation
DAU-9S MBUS Cable
The MBUS Cable DAU-9S has a modular connector, and is used with between PC's serial
port and e.g. Module Jig MJS-63.
Product Code
DAU-9S MBUS Cable: 0730108
Figure 16: View of DAU-9S
Page 20 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
XCS-4 Modular Cable
XCS-4 is a shielded cable (one specially shielded conductor) modular cable for flashing
and service purposes.
Product code
XCS-4 Modular Cable: 0730178
Figure 17: View of XCS-4
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 21
TME-3
Service Tools CCS Technical Documentation
Parallel Cable CA-10 DS
The 1.8m bidirectional parallel cable is used to connect the PC to FPS-8. IEEE 1284-1944
standard compatible.
Product code
Parallel Cable CA-10DS : 0730298
w of Printer Cable Figure 18: View of Parallel Cable
Page 22 Copyright Nokia. All rights reserved. Issue 3 10/03
TME-3
CCS Technical Documentation Service Tools
SB-1 Service Box for TME-3
The primary physical interface to the application is through the 50-pin M2M System
Connector. The M2M system connector offers serial bus, power input/output, Digital
Audio Interface, analogue audios and remote I/O control.
The 50-pin system connector is connected to the application module with a flat cable
connector. The flat cable is connected to a pin header connector on the customer appli-
cation. A board-to-board connector that is connected directly to the M2M system con-
nector of the Nokia 30 GSM Connectivity Terminal can also be used in the customer
application.
Product code:
SB-1 Service box: 0770559
Figure 19: SB-1 service box
Issue 3 10/03 Copyright Nokia. All rights reserved. Page 23
TME-3
Service Tools CCS Technical Documentation
DTX-3 Nokia 32 Application module
DTX-3 Nokia 32 Application module is used for Nokia 30 final testing (audios).
Product code:
DTX-3 NOKIA 32 AM SWAP PACKAGE: 0046604
Figure 20: DTX-3
Page 24 Copyright Nokia. All rights reserved. Issue 3 10/03