Text preview for : DSC-P200-987685433.pdf part of SONY P200 Sony_DSC-P200_Service_Manual
Back to : DSC-P200-987685433.part1. | Home
DSC-P200
SERVICE MANUAL
Ver 1.2 2005.05
Revision History How to use Acrobat Reader LEVEL
2
Photo: Silver
US Model Canadian Model AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Japanese Model
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAM SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST
· · · · ·
For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-854-51). For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-854-41). Reference No. search on printed wiring boards is available. Note in Lens Frame Installation Exchange Method of Barrier Assy On the CH-146, SY-123 boards
This service manual procides the information that is premised the circuit board replacement service and not intended repair inside the CH-146, SY-123 boards. Therefore, schematic diagram, printed wiring board and electrical parts list of the CH-146, SY-123 boards are not shown. The following pages are not shown. Schematic diagrams .................. Printed wiring boards ................ Waveforms ................................ Mounted parts location .............. Electrical parts list ..................... Pages 4-9 to 4-28 Pages 4-39 to 4-42 Pages 4-45 and 4-46 Page 4-48 and 49 Pages 5-7 to 5-11
DIGITAL STILL CAMERA
The above-described information is shown in service manual Level 3.
DSC-P200
9-876-854-31
Sony EMCS Co.
2005E0500-1 © 2005.5 Published by DI Technical Support Section
SPECIFICATIONS
Camera
[System]
Image device 9.11 mm (1/1.8 type) color CCD, Primary color filter
[Power, general]
Battery pack used NP-FR1 Power requirements 3.6 V Power consumption (during shooting with the LCD screen on) 1.2 W Operating temperature 0°C to +40°C (+32°F to +104°F) Storage temperature 20°C to +60°C (4°F to +140°F) Dimensions 104.5×51.5×27.9 mm (4 1/8×2 1/8×1 1/8 inches) (W/H/D, excluding maximum protrusions) Approx. 180 g (6.3 oz) (including NP-FR1 battery pack, "Memory Stick", and wrist strap) Electret condenser microphone Dynamic speaker Compatible
NP-FR1 battery pack
Battery used Lithium-ion battery Maximum voltage DC 4.2 V Nominal voltage DC 3.6 V Capacity 4.4 Wh (1 220 mAh)
Total pixel number of camera Approx. 7 410 000 pixels Effective pixel number of camera Approx. 7 201 000 pixels Lens Carl Zeiss Vario-Tessar 3× zoom lens f = 7.9 - 23.7 mm (38 - 114 mm when converted to a 35 mm still camera) F2.8 - 5.2
Design and specifications are subject to change without notice.
Exposure control Automatic exposure, Manual exposure, Scene Selection (9 modes) White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash, One push
Mass
File format (DCF compliant) Still images: Exif Ver. 2.2 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media "Memory Stick" Flash Recommended distance (ISO set to Auto): 0.2 m to 3.5 m (7 7/8 inches to 11 feet 5 3/4 inches) (W)/0.3 m to 2.5 m (11 7/8 inches to 8 feet 2 3/8 inches) (T)
Microphone Speaker Exif Print
PRINT Image Matching II Compatible PictBridge Compatible
AC-LS5/LS5B AC Adaptor
Input rating Output rating 100 V to 240 V AC, 50/60 Hz, 11 W 4.2 V DC* * See the label on the AC Adaptor for other specifications.
[Input and Output connectors]
Multi connector USB communication Hi-Speed USB (USB 2.0 compliant)
[LCD screen]
LCD panel 5.1 cm (2.0 type) TFT drive Total number of dots 134 000 (560×240) dots
Operating temperature 0°C to +40°C (+32°F to +104°F) Storage temperature 20°C to +60°C (4°F to +140°F) Dimensions Approx. 48×29×81 mm (1 15/16×1 3/16×3 1/4 inches) (W/H/D, excluding projecting parts) Approx. 130 g (5 oz) excluding power cord (mains lead)
Mass
DSC-P200 --2--
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
DSC-P200
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
--3--
TABLE OF CONTENTS
Section Title Page
1.
SERVICE NOTE
1-1. Note for Repair ································································ 1-1 1-2. Discharging of the FP-163 Flexible Board's Charging Capacitor (C601) ····························································· 1-1 1-3. Note in Lens Frame Installation ······································ 1-2 1-4. Description on Self-diagnosis Display ···························· 1-2
2.
DISASSEMBLY
2-1. Disassembly ····································································· 2-1 2-2. SY-123 Board Service Position ······································· 2-5 2-3. Exchange Method of Barrier Assy ·································· 2-7 2-3-1. Peel Off Old Ornamental Ring A ···································· 2-7 2-3-2. Remove Old Barrier Assy ················································ 2-8 2-3-3. Install New Barrier Assy ················································· 2-8 2-3-4. Adhere the Ornamental Ring A ······································· 2-9 2-4. Circuit Boards Location ················································ 2-10
3.
3-1. 3-2. 3-3. 3-4.
BLOCK DIAGRAMS
Overall Block Diagram (1/2) ··········································· 3-1 Overall Block Diagram (2/2) ··········································· 3-3 Power Block Diagram (1/2) ············································· 3-5 Power Block Diagram (2/2) ············································· 3-7
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram ·············································· 4-1 4-2. Schematic Diagrams ························································ 4-5 CD-517 FLEXIBLE (CCD IMAGER) ···························· 4-7 FP-162 FLEXIBLE (DC IN, MULTI CONNECTOR) ·································· 4-29 FP-163 FLEXIBLE (FLASH) ······································· 4-30 MEMORY STICK CONNECTOR (FP-161 FLEXIBLE) ····················································· 4-30 CONTROL SWITCH BLOCK (SW51740), (RL) ········ 4-31 4-3. Printed Wiring Boards ··················································· 4-35 CD-517 FLEXIBLE ······················································ 4-37 FP-162 FLEXIBLE ······················································· 4-43 FP-163 FLEXIBLE ······················································· 4-44 4-5. Mounted Parts Location ················································ 4-47
5.
REPAIR PARTS LIST
5-1. Exploded Views ······························································· 5-2 5-1-1. Overall Assembly ···························································· 5-2 5-1-2. Lens Block Assembly ······················································ 5-3 5-1-3. Main Block Assembly ····················································· 5-4 5-1-4. BT Block Assembly ························································· 5-5 5-2. Electrical Parts List ························································· 5-6
DSC-P200 --4--
1. SERVICE NOTE
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, don't pull at wire of connector. It is possible that a wire is snapped.
When installing a connector, don't press down at wire of connector. It is possible that a wire is snapped.
Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside)
1-2. DISCHARGING OF THE FP-163 FLEXIBLE BOARD'S CHARGING CAPACITOR (C601)
The charging capacitor (C601) of the FP-163 flexible board is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig, a small clip is attached to each end of a resistor of 1 k /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.
1 k/1 W
Discharging the Capacitor Short-circuit between the positive and the negative terminals of charged capacitor with the short jig about 10 seconds.
R:1 k/1 W (Part code: 1-215-869-11) CN757
FP-163 flexible board
Wrap insulating tape.
DSC-P200 1-1
1-3. NOTE IN LENS FRAME INSTALLATION
When tightening a screw, have both sides of the lens block assembly so as not for the load to depend. Lens frame P2 tapping screw
Lens block assembly
1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display · C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) · E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code C:32:ss C:13:ss E:61:ss E:91:ss Countermeasure Turn the power off and on again. Format the "Memory stick". Insert a new "Memory Stick". Checking of lens drive circuit. Checking of flash unit or replacement of flash unit. Cause Trouble with hardware. Unformatted memory stick is inserted. Memory stick is broken. When failed in the focus and zoom initialization. Abnormality when flash is being charged. Caution Display During Error SYSTEM ERROR FORMAT ERROR MEMORY STICK ERROR
--
DSC-P200 1-2E
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds.
R:1 k/1 W (Part code: 1-215-869-11) CN757
FP-163 flexible board
4 3 2 4 4 4 5 5 7 2 1 6 4 3 1 2 3 4 5 6 7 Screw (M1.4) x1 Claw x6 Side cabinet assembly Screw (M1.4) x8 Cabinet plate x1 Cabinet front block Cabinet (rear) block assembly 1 2 3 4 5 Connector x2: CN101, CN202 Connector x1: CN758 Claw x2 Flexible board x1: CN754 Lens block 1 to Page 2-3 3
2
12 3 1 Ornamental ring (A) 2 Tapping screw x2 3 Barrier assy Note: When you exchange rings, be sure to follow the procedure carried on "2-3. Exchange Method of Barrier Assy" (2-7 page).
DSC-P200 2-1 2-2
2 4 3 5 3 3 1 1 2 from Page 2-2 8 7 4 2 1 6 3 P2 tapping screw x1 Multi fixed plate x1 FP-162 flexible board Memory stick connector 4
1 2 3 4
Connector x1: CN707 Connector x1: CN003 Claw x2 Control switch block
1 2 3 4 5 6 7 8
Flexible board x1: CN704 P2 tapping screw x1 Claw x1 P2 tapping screw (M1.7) x1 Claw x1 Connector x2: CN751, 756 Control SW block (SW51740) SY-123 board
1 2 3 4
1
1 2 1 Claw x3 2 D901, LCD901
DSC-P200 2-3 2-4
2-2. SY-123 BOARD SERVICE POSITION
Control switch block
FP-163 flexible board
AC power adaptor
4
AC IN
1
4 3 2
FP-162 flexible board
SY-123 board
2
4 4
3
5
7 2 1 6 4
Control SW block (SW51740)
2
A/V multi cable
3 5
Lens block
8 3 7 4 4 5 1 6
Color monitor Memory stick connector (including FP-161 flexible board) D901, LCD901
1
2 4 3
3
3
1 2
1
1 2
DSC-P200 2-5 2-6
2-3. EXCHANGE METHOD OF BARRIER ASSY
Service parts Part Number 1 3-091-427-01 2 X-3954-476-1 3 3-086-156-31 Part Name Ring (A), Ornamental Barrier Assy Tapping screw (P2) Quantity 1 1 2
2-3-2. REMOVE OLD BARRIER ASSY
1 Remove two screws. * Discard the removed screws. 2 Remove the Barrier Assy. * Discard the removed Barrier Assy.
1
Tools used Torque driver Soldering iron Weight about 60g Adhesive (Super X) (Note) Note: Use adhesive (Super X) or an equivalent article. Don't use what becomes white after drying like a quick-drying glue.
1
2
2
1
3
2-3-1. PEEL OFF OLD ORNAMENTAL RING A
The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force. Heat four circled portions with the soldering iron. Heating temperature is about 300ºC. Beware of a burn since the entire Ornamental Ring becomes hot. * As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame. Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring. * Take extreme care so as not to damage the coated surface of the group-1 frame. In case of difficult peeling, heat the ring again with the soldering iron. If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1 2 3 4 in the under figure one by one sequentially. * Discard the removed Ornamental Ring A.
* After removing the Barrier Assy, if the "G1 Dust-Proof Ring" was removed, it must be returned to the home position. In returning the ring, adjust the location of a projection to the lens direction. This is an important part to prevent the dust and light from coming in. * After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel.
2-3-3. INSTALL NEW BARRIER ASSY
1 Install new Barrier Assy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure. 2 Tighten two screws. * Tightening torque = 0.5 kgf (4.9 N)
4 2 3
Projection 1
2 2
Tip
1
DSC-P200 2-7 2-8
2-3-4. ADHERE THE ORNAMENTAL RING A
Apply an adhesive to four recesses on the top surface of the Barrier Assy. * Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.) Meeting a "notch" of the Ornamental Ring A with a "projection" of the group-1 frame, push the Ornamental Ring A into the group-1 frame. * The projection of the spring for preventing static electricity must be tilted. Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens. Note: Be careful not to give a shock. * After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame. A gap, if present, causes the crackle sound NG. * The weight must push in the Ornamental Ring A only. If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up.
Do not put the weight on a black mold part. Notch Adhesive Adhesive Adhesive Projection
Adhesive Not gap in full circumference.
Completion after 30 minutes.
DSC-P200 2-9
2-4. CIRCUIT BOARDS LOCATION
Control switch block SY-123 (including CP101 (CH-146 board) and IC301 (KFW board)) Control SW block (SW51740)
FP-163 flexible CD-517 flexible
FP-162 flexible
CH-146 (included in SY-123) FP-161 flexible (included in Memory stick connector)
Board Name
Function
CD-517 flexible CH-146 (included in SY-123) FP-161 flexible (included in Memory stick connector) FP-162 flexible FP-163 flexible SY-123 (including CP-101 (CH-146 board) and IC301 (KWF board))
CCD IMAGER CCD SIGNAL PROCESS MEMORY STICK CONNECTOR
DC IN, MULTI CONNECTOR FLASH CAMERA MODULE, CAMERA DSP, LENS DRIVE, SH DSP, FRONT CONTROL, LCD DRIVE, AUDIO, DC/DC CONVERTER, CONNECTOR
DSC-P200 2-10E
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (2/2)
DSC-P200
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
LENS BLOCK LENS IRIS (METER) 17
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-123 BOARD (1/2)
CN101 (1/2) 16 CCD OUT 6 86 134 136 2 4 6 9 12 15 18 21 24 27 30 32 49 105 66 101 120 99 IC101 22 i 35 CA AD00 CA AD13 CP101 CAMERA MODULE (1/9) Y11 AB11 Y10 AA11 AB10 Y9 AB9 AA10 AA9 Y8 AB8 AA8 AB7 AA7 Y7 AB6 AC8 F1 D1 E1 C6 D7 PANEL R PANEL G PANEL B HDO PANEL V XSYS RST D11 E11 F11 A2 B1 C1 A5 B4 A4 XPANEL TG CS BL LEV B5 G10 BL H BL L L6 L7 L8 J11 PANEL UNIT CN754 VR 21 VG 20 VB 22 COM, CS RGT, HCK1, HCK2, HST, PCG, XSTBY, DWN, EN, VST, VCK, REF, VP 1 2 3 i 6 11 i 14 17 i 19 23 26 25
CD-517 FLEXIBLE BOARD (1/2)
Q103 BUFFER Q101
CH-146 BOARD
LCD901
19 IC101 SHUTTER MOTOR ZOOM MOTOR FOCUS MOTOR IRIS MOTOR CCD IMAGER Q102 23 25 24 28 29 FOCUS SENSOR 13 RG, H1B, H2B H1A, H2A 4 10 7 9 6 PWR SAVE 37 5 2 4 1 3 9 12 i 14 20 15 i 18 7 11 10 8 19 21 Q108 27 VSUB CONT 22 Q105 36 133
IC801 LCD DRIVE (6/9)
M
M
M
M
CAM F
33 42 51 CCD SIGNAL PROCESSOR, 37 TIMING 48 GENERATOR 113 109 112 115 7 125 119 118 121 10 20 17 13 11 19 135
45 46 48
CA HD CAM F MCKTG
COLOR LCD MONITOR
E1 F1 G2 H2 H1 J2 J1 K1 K3 L3 H11 K11 L10
D901 BACKLIGHT
3 123 126129
1 6 7 3 5 26
V1, V3A, V3B VST VHLD VSUB
36 32 33 35 31 21
40 i 42
IC301 CAM SO, XCAM SCK, XCAM RST CAMERA DSP, SDRAM (KWF BOARD) (2/9)
SYS SI, SYS SO, XSYS SCK
4 8 i 15
V2, V4, V5A, V5B, 34 V6, V7, V8, V9, V10 30 i 23
132 124
38 XFE CS, XTG CS 39
84
47
TG CKI
AC4
BL L BL H BL LEV IC302
3
OVERALL (2/2) (PAGE 3-4)
CAM SO, XCAM SCK, XCAM RST
G1 AC22 AC12 AC15 N3 K3 M4
VSUB CONT IC 301 IC201
YO VIDEO AMP ON
4 1
VIDEO AMP (2/9)
2
V OUT
CN201 F MOTOR A, A, B, B 23 i 26 FOCUS A, A, B, B
A6 B5 A4 B4
FOCUS MOTOR DRIVER
LENS DRIVE HR EN2, (3/9) HR DIR2A, B7 HR DIR2B B8 C7 C8 B3 A2 B1 HR EN0, HR DIR0A XZM DC BR
AU AIN AU AOUT SYS SO, XSYS SCK
D21 K4 J3 XPANEL TG CS AD16 A11 B11 C11 D14 K2 AA8 IC502 MC CAM, SH DSP, FLASH (4/9)
Z DC MOTOR (+), ()
9 i 12
ZOOM DC ±
C1 D2
ZOOM MOTOR DRIVER
AA18 D22 AB7 AD14 J1 K1 L1 M1 F1 H23
XAU LINE MUTE AU SEN MELODY ENV MELODY
1
OVERALL (2/2) (PAGE 3-3)
SYS SI, SYS SO, XSYS SCK IRIS M IN IRIS M EN IRIS S IN IRIS S EN MSHUT DIR MSHUT EN MSHUT REF XFC RST SENS XZM RST SENS1 T4 U2 T3 T2 U3 AA19 P4 D8 AA12 XSYS RST SYS V
USB PHY D±
ZOOM FG
ZOOM SENSOR
IRIS M±, S±
17 i 20
IRIS M±, S±
G5 H6 G4 H4
IRIS MOTOR DRIVER
G3 H2 G2 G1 F8 F7 H8
PRELAMP AF CONT SELF TIMER LED AE LOCK LED
SHUTTER MOTOR (+), ()
13 i 16
SHUTTER±
E7 D7
SHUTTER MOTOR DRIVER
F PI SENS OUT Z PI SENS OUT Z BOX1 PI SENS OUT, Z BOX2 PI SENS OUT LENS TEMP SENSOR THERMISTOR (+)
33 29 Q205 4 7 30
ZM DC FG A, B
J21 L22 L20 L23 K21 G4 J2 Y4 L21 M21 M23 M20 M22 G3 H4 W4 N21 N22 N20 P20 P21 P23 R21 P22 T21 R23 STRB ON R20 R22 T20 T23 U21 AB20 P1
F4 F3
J23 J22 U20 V21 V23 U22 V20 V22 W20 Y20 W22 Y23 W21 Y22 Y21 AA22 AA21 AB22
MC XCS IC 301REG MC XCS IC 301SDRAM
MC D0 D15
A17 C18 L21 L23 M24 K23 H22 J21 J22 F24 K21 H21 M23 K22 G21 L24 F23 E23 V22 V21 V23 R22 W22 U22 W21 T22 R23 N21 P22 P21 P23 R21 M22 T21 P24 U21 U23 N22 U24 N23 T24 M21 T23 A7 H1 AC12 AA9 AC16 A2 A12 B12 C23
AD20
D753 (MS ACCESS) C22 XACCESS LED Q752 LED DRIVE
MC A1 A25
MC CKIO CAM F XFE CS XTG CS LENS TEMP
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
LENS TEMP
B16 B15 D16
FP-163 FLEXIBLE BOARD
XE_H 1 i 3 CN757 XE_H T601 D601 5 4 1 ST UNREG
MC MSDIO, MC MSBS, CN751 (FP-161 FLEXIBLE) MC MSCLK 9 DIO, BS, SCLK 11 4 INT 7
MEMORY STICK CONNECTOR
MEMORY STICK CN001 4 2 8 6
CAM SO, XCAM SCK, XCAM RST XZM DC BR MSHUT REF VER EXTAL X101 27MHz STRB CHRG XSTRB FULL
AA19 G2 A6
AB5 AB13 B13 D13 C13
XMS IN XAE LOCK ON XSHTR ON
FLASH UNIT
TRIG 300V
11 TRIG 300V 12
3
2 5 2 IC601 TRANS DRIVE, FLASH CONTROL, FLASH CHARGE DETECT (9/9) 8 7 STRB CHRG XSTRB FULL
FR SI, FR SO, XFR SCK FR INT XCS MC
XE_L CL501
6 i 8
XE_L
AD19 AC15
AD11 D11
2
OVERALL (2/2) (PAGE 3-3)
C601 CHARGING + CAPACITOR 05
Q601 CL502
6
4
STRB ON
D602
XSYS RST SYS V
DSC-P200 3-1 3-2
3-2. OVERALL BLOCK DIAGRAM (2/2)
SY-123 BOARD (2/2)
V OUT
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-162 FLEXIBLE BOARD
21 ACV UNREG 23 25 BATT XEXT 19 15 KEY ADA, ADB 9 XLANC POWER ON 7 2 CHG STAT 0 2 17 24 CN704 (2/2) IC901 CN758 A2 A4 SP ± 1 2 SP901 SPEAKER 23 20 36 17 19 18 21 1 2 9 3744 45 ACV UNREG BATT /XEXT D J101 DC IN
CN704 (1/2) V OUT AU OUT XAV JACK IN USBPHY D± USB JACK IN AU AIN AU AOUT H6 H7 H2 H3 34 31 22 26 28 24 V OUT A OUT L XAV JACK IN D± USB VBUS 20 16 26 10 12 6
CN101 (MULTI CONNECTOR)
BATT UNREG BATT SIG
USBPHY D±
+ S -
BT901 BATTERY TERMINAL
F1
OVERALL (1/2) (PAGE 3-2)
1
SYS SO, XSYS SCK XAU LINE MUTE AU SEN MELODY ENV MELODY AE LOCK LED PRELAMP AF CONT SELF TIMER LED AE LOCK LED Q504 MODULATOR BEEP
XLANC POWER ON
CHG STAT 0 2
KEY ADA, ADB
BATT XEXT M BATT XEXT D
ACV UNREG1
BATT UNREG
G4 AUDIO AMP (7/9) H4 C1
A7
F9 F7 E9 USB JACK IN Q408 C8 A3 A8 J7 H7
CHG STAT 0 2
MIC901 MICROPHONE
2
CN707 MIC IN
XAV JACK IN
Q402 A7 BATT/XEXT Q407 BATTERY CHARGE DETECTOR S401 RESET BUFFER
CD-517 FLEXIBLE BOARD (2/2)
D104 SELF TIMER/ AF ILLUMINATOR CN101 (2/2) PRELAMP AF ON 38 Q701 LED DRIVE Q503 LED DRIVE XMS IN Q401 B6 D1 D2 E1 D9 E2 B3 B9 J5 J4 G1 G2
BATT SIG IC402
D103 (AE/AF LOCK)
FR SI, FR SO, XFR SCK AE LOCK LED
IC401 FRONT CONTROL (5/9) D7
XAE LOCK LED
DC JACK/MULTI DOUBLE INSERTION DETECT (5/9)
43
2
OVERALL (1/2) (PAGE 3-2)
D101 (FLASH/CHG)
XCHARGE/XSTRB LED
44
FR INT XCS MC XSYS RST SYS V XSHTR ON XAE LOCK ON
XRSTX
B7 C7 D7 E4 L8 K8 K7 A7 E3 D2
ACV UNREG ST UNREG ACV W SENS CHG SW
E8
SYS DD ON
Q008, 009
X401 32.768kHz
C1 D3 H1 A9 H2 J1
DDCON SO, DDCON SCK XCS DDCON BATT IN FAST CHARGE INIT CHARGE
CONTROL SWITCH BLOCK (RL)
S001 (SHUTTER) 1 2
CONTROL SWITCH BLOCK (SW51740)
CN003 XAE LOCK ON XSHTR ON 6 5 XCHARGE/XSTRB LED XPWR LED CN756 PLL LOOP FILTER
BATT UNREG
J2 J3
D001 (POWER) S002 POWER
3
XPWR LED
4
B1 B2
5
XPWR ON
2 8 11
XPWR ON
B8 J8 J9
MODE DIAL
MODE DIAL 0, 1
(ZOOM) T W FUNCTION KEY 18 19
KEY AD 0, 1
J6 H6
PANEL 8.5V BACK UP VCC EVER 3.0V A 3.1V D 1.2V D 2.8V A 2.8V CAM 15.5V CAM 7.5V/8.0V CAM 3.3V M 5V ST 5V CAM 0.5V A10 VL 3V D8
IC002 DC/DC CONTROL, RESET (8/9)
ACV UNREG
G1 G2 B1
BL H BL L BL LEV
3
OVERALL (1/2) (PAGE 3-2)
12 VL 3V
KEY AD 2
G6
BT001 LITHIUM BATTERY 05
15
A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL
DSC-P200 3-3 3-4
BATT SIG
3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis (
FP-162 FLEXIBLE BOARD SY-123 BOARD (1/2)
CN704
) indicates the division number of schematic diagram where the component is located.
+
BT901 BATTERY TERMINAL
BATT UNREG1 BATT SIG
S -
37 i 44 45 Q008, 009
F001 D 1.2V ACV UNREG IC002 D005 DC/DC CONTROL, RESET (8/9) L001, 010 L009 D9 OUT8A E9 OUT8B B11 VCC8 E4 CHG SW Q001 1 DC CONTROL (8/9) 4 IC003 E5 MARK D4 BATT D8 VBCK IC402 DC JACK/MULTI DOUBLE INSERTION DETECT (5/9) G11 VCC1A G10 VCC1B G9 VCC1C VCH1A VCH1B VCH1C (FB4) VLDO1 L10 K9 L9 A11 CBG B5 L011 SWITCHING
ST UNREG
LF101 J101 DC IN ACV UNREG1 2 i 9
F002
D006
F004
CAM 0.5V
21 23 25 CN101 MULTI CONNECTOR 19 7 2 17 24
ACV UNREG BATT/XEXT D BATT/XEXT M XLANC POWER ON CHG STAT0 2 2 1
D1 VDCIN D002 1 21 17 23 20 36 4
D403
D404
A 2.8V D 2.8V
D 1.2V BATT UNREG ACV UNREG
EVER 3.0V
CONTROL SWITCH BLOCK (SW51740)
BT001 LITHIUM BATTERY VL 3V 15
F9 VCC2 B9 VLDO2 D004 A10 J3 K1 J2 VLDO3 OUT3A OUT3B OUT3C
VCH2 E11 OUT2 F10 L002
D 1.2V
CN756 VL 3V
CONTROL SWITCH BLOCK (RL)
D001 (POWER) 4
L005
VCH3A (FB3) VCH3B VCH3C (FB6) VCH3S
J1 H4 H3 H2
M 5V
ST 5V
CN003 EVER 3.0V 3
BACK UP VCC
A
CAM 15.5V D009 L006 A 3.1V
VCC GD H1 VCH4 J6 OUT4 K6 VLDO4 C8
POWER 2 (PAGE 3-7)
K5 VCC5 IC401 FRONT CONTROL (5/9) G8 ACV SENS H8 BATT SENS F8 DD CON SENS Q407 BATTERY CHARGE DETECTOR Q402 BUFFER A7 BATT/XEXT A8 XLANC PWR ON F9 CHG STAT0 F7 CHG STAT1 E9 CHG STAT2 C1 D3 H1 A9 H2 J1 E8
VCH5 J5 D008 OUT5 L5 VLDO5 B8 L007
CAM 8.0V
PANEL 8.5V
VCH6 G1 D007 OUT6 F1 ICH6 G2 REF6 B1 Q011, 012 VCC7 J4 DDCON SO, DDCON SCK XCS DDCON BATT IN FAST CHARGE INIT CHARGE SYS DD ON L8 DIN K8 CLK LD CS FCHG ICHG C7 SYSDDON D7 USB PWR ON K7 A7 E3 D2 VOS72 K4 VOS73 L3 Q010 VCH7 K3 DC CONTROL SWITCHING L012 L003
BL H BL L
BL LEV
G1 BATT SO G2 BATT SI
CAM 3.3V
CHG STAT0 2
EVER 3.0V
05
DSC-P200 3-5 3-6
3-4. POWER BLOCK DIAGRAM (2/2)
SY-123 BOARD (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
T601 ST UNREG L601
CN757 1 i 3
FP-163 FLEXIBLE BOARD
ST UNREG FLASH UNIT
IC601 ST 5V TRANS DRIVE, FLASH CONTROL, FLASH CHARGE DETECT (9/9) CN754 7 L813 IC801 IC802 CAM 3.3V A 2.8V (PANEL 2.8V) BL LEV BL H BL L 26 25 BL H BL L 5 2.8V REG (6/9) 4 EXTDA G10 D901 BACKLIGHT L105 50 FB102 51 FB103 49 LCD DRIVE (6/9) VDD LCD901 54 55 71 L104 L103 53 FB105 56 52 57 IC101 CCD SIGNAL PROCESSOR, TIMING GENERATOR CP101 CAMERA MODULE (1/9) PANEL UNIT
CH-146 BOARD
PANEL 8.5V L804
M 5V (PANEL 4.9V)
COLOR LCD MONITOR
POWER 1 (PAGE 3-6)
A
CAM 3.3V CAM 0.5V Q101, 102 CAM 15.5V CAM 8.0V M 5V A 2.8V D 2.8V EVER 3.0V A 2.8V D 2.8V
CAM 3.3V CAM 0.5V CAM 15.5V CAM 8.0V M 5V A 2.8V 40 EVER 3.0V 45 D 2.8V (XAE LOCK) EVER 3.0V CN101 L101 12 FB108 1 39
CD-517 FLEXIBLE BOARD
CAM 15V IC101 CAM 8.0V M 5V CCD IMAGER D104 SELF TIMER/ AF ILLUMINATOR D103 (AE/AF LOCK) D101 (FLASH/CHG)
CAM DD ON A 2.8V M 5V (AUDIO) L504 A 2.8V D2.8V IC501 4 1.8V REG (4/9) A 3.1V D 1.2V L304 D 2.8V D 1.2V FB301 FB302 FB305 L301 FB304 IC301 CAMERA DSP, SDRAM (KWF BOARD) (2/9) PI006 V4 PI007 V3 L502 1 L503
AC20 PU[6]
IC502 MC CAM, SH DSP, FLASH (4/9) Q751 CN751 2 SDA(O/D) AD18 MS POWER ON VCC
MEMORY STICK CONNECTOR (FP-161 FLEXIBLE)
CN001 9 MEMORY STICK
A 3.1V D 1.2V
LENS BLOCK Q201 (1/2) D 2.8V XLENS RST LED Q201 (2/2) D 2.8V XZM RST LED 6 1 Z BOX2 PI SENS Vcc Z BOX1 PI SENS Vcc 28 Z PI SENS Vcc FOCUS SENSOR CN201 32 F PI SENS Vcc ZOOM SENSOR
A 2.8V AU 2.8V L901 IC901 AUDIO AMP (7/9)
L302
L303
IC302 VIDEO AMP (2/9) D 2.8V M 5V IC201 LENS DRIVE (3/9)
ZOOM FG
05
DSC-P200 3-7 3-8E
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CN101 45P 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
16
17
18
19
20
21
A
FRAME SCHEMATIC DIAGRAM
C601 CHARGING CAPACITOR
CAM_-8.0V GND GND RG GND H2A H2B GND
B
FP-163 FLEXIBLE BOARD
(FLASH)
FLASH UNIT
H1A H1B GND CAM_15V PWR_SAVE GND
LENS BLOCK
OVF LENS
C
CONTROL SWITCH BLOCK(RL)
2P 6 5 4 3 2 1 CN707 CN756 19P 1 2 3 4 5 6 7 8 REG_GND XPWR_ON EVER_3.0V XPWR_LED XSHTR_ON XAE_LOCK_ON MANUAL MODE_DIAL1 MOVIE PB MODE_DIAL0 KEY_AD2 REG_GND NC VL_3V NC REG_GND KEY_AD1 KEY_AD0
GND CDD_OUT MIC901 MIC N.C. CCD_GND GND GND 10 11 12 13 14 15 16 17 18 2 1 1 2 3 4 5 6 7 8 9 VSUB VSUB_CONT V10 V9 V8 V7 V6
XPWR_LED
EVER_3.0V
XSHTR_ON
CN003
D
XAE_LOCK_ON
REG_GND
XPWR_ON
CD-517 FLEXIBLE BOARD
(CCD IMAGER)
CCD
MIC_SIG
MIC_GND
18P
XE_L
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
XE_H
XE_H
XE_H
XE_L
XE_L
N.C.
ST_GND
ST_GND
TRIG_300V
CN757
TIRG_300V
6P
ST_GND
CP101
GEAR BOX
V5B V5A
E
F
CONTROL SWITCH BLOCK (SW51740)
9 10 11 12 13 14 15 16 17 18 19
SY-123 BOARD
(1/9) (CAMERA MODULE) (2/9) (CAMERA DSP) (3/9) (LENS DRIVE) (4/9) (SH DSP) (5/9) (FRONT CONTROL) (6/9) (LCD DRIVE) (7/9) (AUDIO) (8/9) (DC/DC CONVERTER) (9/9) (CONNECTOR)
CH-146 BOARD
CCD SIGNAL PROCESS IC301
V4 VHLD V3A V3B V2 VST V1 N.C. PRELAMP_AF_ON M_5V D_2.8V(AE_LOCK) XAE_LOCK_LED
KWF BOARD
N.C. N.C. XCHARGE/XSTRB_LED EVER_3.0V CN201 33P
CN758
2P
F_PI_SENS_OUT F_PI_SENS_Vcc
33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
G
SP901 SPEAKER
1 2
SPSP+ REG_GND THERMISTOR(+) Z_PI_SENS_OUT Z_PI_SENS_Vcc XLANC_POWER_ON N.C. USB/LANC_GND USB/LANC_GND BATT/XEXT_M XAV_JACK_IN BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG F_MOTOR B CN751 12P SDIO/DATA0 BATT_SIG F_MOTOR A DATA1 F_MOTOR B VSS BS F_MOTOR A N.C. N.C. IRIS_M_IRIS_M_+ IRIS_S_IRIS_S_+
ACV_UNREG1
ACV_UNREG1
ACV_UNREG1
ACV_UNREG1
ACV_UNREG1
ACV_UNREG1
ACV_UNREG1
CN704 45P
ACV_UNREG1
BATT/XEXT_D
26P
CHG_STAT1
CHG_STAT0
CHG_STAT2
USB_VBUS
KEY_ADB
KEY_ADA
A_OUT_L
A_GND
V_GND
V_GND
V_OUT
XSTBY
CN754
VSSG
HCK2
HCK1
BL_H
TEST
TEST
BL_L
DWN
COM
GND
GND
GND
GND
GND
GND
GND
VDD
PCG
RGT
SCLK
VSS
VCC
VSS
VCK
VSS
HST
N.C.
N.C.
VST
REF
VSS
VG
VR
NC
NC
CS
VP
VB
EN
D+
D-
INT
H
DATA3
DATA2
10
11
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
45
12
7
1
2
3
4
5
6
7
8
9
1
2
3
4
5
1
2
3
4
5
6
7
8
9
6
8
9
LENS FLEXIBLE
I
PANEL UNIT LCD901 2.0 INCH COLOR LCD MONITR
J101 DC IN
SHUTTER_MOTOR(-)
FP-162 FLEXIBLE BOARD
(DC IN, MULTI CONNECTOR)
CN101 28P (MULTI CONNECTOR) 27 2 1
CHG_STAT0 NC(FR_EXT_BATT) USB_VBUS USB_GND D+ DUSB_GND A_OUT_L A_GND V_OUT V_GND CHG_STAT2 XAV_JACK_IN ACV_GND ACV_GND ACV_GND XLANC_POWER_ON KEY_ADB N.C. N.C. KEY_ADA CHG_STAT1 BATT_XEXT ACV_UNREG ACV_UNREG ACV_UNREG
6
5
J
26 24 22 20 18 16 14 12 10
D901 BACKLIGHT
BT901 BATTERY TERMINAL
25 23 21 19 17 15 13 11
MEMORY STICK CONNECTOR FP-161 FLEXIBLE BOARD
CN001 12P VSS SCLK VCC DATA1 DATA2 DATA3 VSS DIO INT BS 10 1 4 6 5 2 3 7 8 9
SHUTTER_MOTOR(-) SHUTTER_MOTOR(+) SHUTTER_MOTOR(+) Z_DC_MOTOR(-) Z_DC_MOTOR(-) Z_DC_MOTOR(+) Z_DC_MOTOR(+) REG_GND
Z_BOX2_PI_SENS_OUT Z_BOX2_PI_SENS_Vcc Z_BOX2_PI_SENS_Col Z_BOX1_PI_SENS_OUT
4
8
9
7
3
REG_GND
Z_BOX1_PI_SENS_Col Z_BOX1_PI_SENS_Vcc
K
28 TO AV/USB MULTI CABLE OR CRADLE
Note: FP-161 flexible board is supplied as MEMORY STICK CONNECTOR.
11
12 MEMORY STICK
L
MEMORY STICK
05
DSC-P200 4-1 4-2
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CD-517 FLEXIBLE (CCD IMAGER) FP-162 FLEXIBLE BOARD
(DC IN, MULTI CONNECTOR)
FP-163 FLEXIBLE BOARD (FLASH) MEMORY STICK CONNECTOR
(FP-161 FLEXIBLE)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-P200
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) · All capacitors are in µF unless otherwise noted. pF : µ Link V or less are not indicated except for electrolytics µF. 50 and tantalums. · Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor Case Size External dimensions (mm) · Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · Parts with differ according to the model/destination. Refer to the mount table for each function. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2: non flammable resistor · 5: fusible resistor · C: panel designation · A: B+ Line · B: B Line · J : IN/OUT direction of (+,-) B LINE. · C: adjustment for repair. · A: not use circuit · Circled numbers refer to waveforms. (Measuring conditions voltage and waveform) · Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M input impedance is used) · Voltage values change depending upon input impedance of VOM used.)
Front of the lens
1. Connection
Pattern box Color bar chart
Pattern box PTB-450 J-6082-200-A or Small pattern box PTB-1450 J-6082-557-A
Pattern box
For PTB-450: J-6020-250-A For PTB-1450: J-6082-559-A
L = About 28 cm(PTB-450) L = About 12 cm(PTB-1450) USB,AV cable for multi-use terminal
L
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow Cyan Green White Magenta Red
H
B B A A A=B/2 Fig. a (Video output terminal output waveform) Electronic beam scanning frame CRT picture frame
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please include the board name.
Note :
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note :
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie.
DSC-P200 4-5
Blue
For Schematic Diagram · Refer to page 4-37 for printed wiring board.
1
2
3
4
5
6
7
8
A
CD-517 FLEXIBLE BOARD
CCD IMAGER (CCD BLOCK)
XX MARK:NO MOUNT
LND101 LND102 LND103 LND104 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 EVER_3.0V
XCHARGE/ XSTRB_LED
Note: CD-517 flexible complete board and IC101 are not supplied, but there are included in CCD block assy.
D101 SML-310YTT86 (FLASH/CHG) D102 XX D103 CL-196HR-CD-T (AE/AF LOCK) D104 OPY5252 (SELF TIMER/AF ILLUMINATOR)
N.C. N.C.
XAE_LOCK_LED D_2.8V (AE_LOCK)
Note: Voltage and Waveform of mounted on CD-517 flexible board can not be measured, because they are mounted by the side of the lens.
B
LND105 LND106 LND107 LND108 LND109 LND110 LND111 LND112
M_5V
PRELAMP_AF_ON
N.C. V1 VST V2 V3B V3A VHLD V4 V5A V5B V6 V7
CL107 CL111 CL101 CL103 CL102 CL114
C
LND113 LND114 LND115 LND116 LND117 LND118 LND119 LND120
D
LND121
V8 V9 V10 VSUB_CONT
SY-123 (1/9)
CN101 PAGE 4-11 of LEVEL3
LND122 LND123 LND124 LND125 LND126 LND127 LND128
16 15 14 13 12 11 10
V5B V10 V7 NC V9
9
V5A
8
V4
7
V3B
6
V3A
5
VHLD
4
V2
3
VST
2
NC GND
1
V1 NC
GND GND CCD_GND N.C. CCD_OUT GND GND PWR_SAVE CAM_15V GND H1B H1A GND H2B H2A GND RG GND GND CAM_-8.0V R109 0 Q103 2SC4250(T5LSONY1) BUFFER R102 12k C103 XX R101 33 C101 XX Q101 DTC144EMT2L SWITCH
V8
V6
VSUB
E
LND129 LND130 LND131 LND132 LND133 LND134 LND135 LND136
IC101
R103 2700
VOUT GND GND GND VDD NC
CCD IMAGER IC101 ICX489CQZ-13
CSUB SUB H2B H1B H1A H2A
RG
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
CL120
LND138 LND139 LND140 LND141 LND142 LND143 LND144
G
LND145
CL121
C107
F
LND137
0.1u
VL
R104 1200 C106 0.1u Q102 DTC144EMT2L SWITCH C104 XX R105 1500 C102 0.1u C105 0.1u
H
05
Precautions for Replacement of CCD Imager · The CD-517 flexible board mounted as a repair part is not equipped with a CCD imager. When replacing this board, remove the CCD imager from the old one and mount it onto the new one. · If the CCD imager has been replaced, carry out all the adjustments for the camera section. · As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light.
DSC-P200 4-7 4-8
CD-517
Schematic diagrams of the CH-146, SY-123 boards are not shown. Pages from 4-9 to 4-28 are not shown.
DSC-P200
For Schematic Diagram · Refer to page 4-43 for printed wiring board.
1
2
3
4
5
6
7
1
2
3
4
5
A
FP-162 FLEXIBLE BOARD
DC IN, MULTI CONNECTOR (JK BLOCK)
XX MARK:NO MOUNT NO MARK:REC/PB MODE
LND146 BATT_UNREG LND147 LND145 45 BATT_SIG
BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG BATT_UNREG
A
BT901 BATTERY TERMINAL
FP-163 FLEXIBLE BOARD
FLASH (STROBE BLOCK)
LND518 LND517 LND516 1 2 3 XE_H XE_H LND521 XE_H XE_H
Note: CN101 (multi connector) is not supplied, but this is included in FP-162 flexible complete board.
LND150 STATIC_GND
Note: FLASH UNIT and C601 are not included in FP-163 flexible complete board.
B
LND144 44 LND143 43 LND142 42 LND141 41 LND140 40 LND139 39 LND138 38 LND137 37
BATT_SIG LND148 BATT_GND
S
B
LND523 TRIG_300V
D101 MA2S111-(K8).SO 27
2
SY-123 (9/9)
ACV_GND ACV_GND ACV_GND XLANC_POWER_ON KEY_ADB N.C. N.C. KEY_ADA CHG_STAT1 BATT_XEXT ACV_UNREG ACV_UNREG ACV_UNREG
1
LND513 LND512 LND511
5 6 7
XE_L XE_L XE_L
FLASH UNIT
CN757 PAGE 4-28 of LEVEL3
BATT_UNREG BATT_UNREG
CHG_STAT0 NC(FR_EXT_BATT) USB_VBUS USB_GND D+ DUSB_GND A_OUT_L A_GND V_OUT V_GND CHG_STAT2 XAV_JACK_IN 28
LND524 TRIG_GND
4
C
LND136 36 LND135 35 LND134 34 LND133 33 LND132 32 LND131 31 LND130 30
6
CHG_STAT2 V_GND V_OUT V_GND A_GND A_OUT_L NC
5
3
C
8
7
26 24 22 20 18 16 14 12 10
LND508
XE_L 11 TRIG_300V TRIG_300V LND522
9
25 23 21 19 17 15 13 11
LND507 12
LND503 16 LND502 17 LND501 18
ST_GND ST_GND ST_GND
CL501 CL502
LND129 29 USB/LANC_GND
C601 117u 315V CHARGING CAPACITOR
D
SY-123 (9/9)
CN704 PAGE 4-28 of LEVEL3
LND128 28 LND127 27 LND126 26
DNC D+
D
05
LND125 25 USB/LANC_GND LND124 24 LND123 23 LND122 22 LND121 21 USB_VBUS CHG_STAT0
XAV_JACK_IN BATT/XEXT_M
CN101 28P (MULTI CONNECTOR) TO AV/USB MULTI CABLE OR CRADLE
E
LND120 20 LND119 19 LND118 18
CHG_STAT1 KEY_ADA KEY_ADB
1
LND117 17 XLANC_POWER_ON LND116 16 LND115 15 LND114 14 LND113 13 GND GND GND GND GND GND GND
ACV_UNREG1 ACV_UNREG1 ACV_UNREG1 ACV_UNREG1 ACV_UNREG1 ACV_UNREG1 ACV_UNREG1 ACV_UNREG1 BATT/XEXT_D
2
3
4
5
F
LND112 12 LND111 11 LND110 10 LND109 LND108 LND107 LND106 LND105 LND104 9 8 7 6 5 4 3 2 1
5 LF101 0uH 3 2 4 1 2 3 1 4 LND149 STATIC_GND
A
J101 DC IN
MEMORY STICK CONNECTOR (FP-161 FLEXIBLE BOARD)
MEMORY STICK CONNECTOR (FP-161 flexible board) is replaced as block, so that PRINTED WIRING BOARD is omitted.
B
LND001 LND002 LND003 LND004 LND005
1 2 3 4 5 6 7 8 9 10 11 12
VSS VCC VSS SCLK CN001 12P VSS DATA3 8 SCLK DATA3 INT DATA2 DIO DATA1 BS VSS 11 MEMORY STICK INT DATA2 5 DIO DATA1 2 BS VSS 1 4 3 7 6 10 9 VSS VCC 12 MEMORY STICK
G
LND103 LND102 LND101
05
C
SY-123 (9/9)
CN751 PAGE 4-27 of LEVEL3
LND006 LND007 LND008 LND009 LND010 LND011 LND012
D
LND013
STATIC_GND
05
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
DSC-P200 4-29 4-30
FP-162, FP-163, MEMORY STICK CONNECTOR (FP-161)
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
A
CONTROL SWITCH BLOCK (SW51740)
CONTROL SWITCH BLOCK (SW51740) is replaced as block, so that PRINTED WIRING BOARD is omitted.
CONTROL SWITCH BLOCK (RL)
CONTROL SWITCH BLOCK (RL) is replaced as block, so that PRINTED WIRING BOARD is omitted. CN003 6P REG_GND 1 XPWR_ON 2 EVER_3.0V 3 XPWR_LED _ON 4 XSHTR_ON 5 XAE_LOCK _ON 6 D001 (POWER) S002 POWER 6 REG_GND XPWR_ON EVER_3.0V XPWR_LED XSHTR_ON XAE_LOCK_ON XPWR_ON 5 EVER_3.0V 4 XPWR_LED 3 XSHTR_ON 2 XAE_LOCK_ON 1
B
REG_GND XPWR_ON EVER_3.0V XPWR_LED XSHTR_ON XAE_LOCK_ON MANUAL
CL001 CL002 CL003 CL004 CL005 CL006 CL007 CL008 CL009 CL010 CL011 CL012 CL013 NC (FLASH) (MACRO) XPWR_ON EVER_3.0V XPWR_LED XSHTR_ON XAE_LOCK_ON
S001 (SHUTTER) NO
C
SY-123 (5/9)
CN756 PAGE 4-19 of LEVEL3
MODE_DIAL1 MOVIE PB MODE_DIAL0 KEY_AD2 REG_GND
(1st) R008 3300 (2nd)
VL_3V
CL015 NC
CL032
CL035
CL033
CL034
D
REG_GND KEY_AD1 KEY_AD0
CL017 CL018 CL019
BT001 LITHIUM BATTERY
(SET)
R007 1500
CL031
CL030
E
(REVIEW)
(SELF TIMER)
CL029
CL028
CL027
CL026
KEY_AD1 R006 1200 R009 1200
KEY_AD0
F
R010 1500
R011 3300
IMAGE SIZE/ DELETE
CL025
CL024
W
T MENU DISPLAY/ LCD ON/OFF
G
CL040 KEY_AD2
W
(ZOOM)
T CL020 CL021 CL022 CL023
CL045 R005 1200
CL038
CL039
H
6 POSITION MODE_DIAL MOVIE 5 CL046 6 CL042 CL036 PB 4 CL048 SCN
I
MODE_DIAL0 AUTO 1 CL044 CL043 CL041 2 P_AUTO R002 1500 R001 1200
3
MANUAL
J
MODE_DIAL1
K
05
DSC-P200 4-31 4-32
(SW51740), (RL)
4-3. PRINTED WIRING BOARDS
Link
CD-517 FLEXIBLE BOARD FP-162 FLEXIBLE BOARD FP-163 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION
Board Name
Function
CD-517 flexible FP-162 flexible FP-163 flexible
CCD IMAGER DC IN, MULTI CONNECTOR FLASH
DSC-P200
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
· · : Uses unleaded solder. : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers' patterns are not indicated) Through hole is omitted. Circled numbers refer to waveforms. There are a few cases that the part printed on diagram isn't mounted in this model. C: panel designation · Chip parts. Transistor
C 6 5 4 4 5 6 5 4 4 5
Diode
3 3 3 1 23
B
E
1 2 3 3 2 1 1 2 3 3 2 1 1 2 2 1 3 2
2 4
1 2 3 3
1 2
1 6 54
· · · ·
4 6 5 4 4 5 6
5 4 3 3 4 5 4
1
1 3
2 2
2
1 1 2 3 3 2 1
4
1
Board Name CD-517 flexible FP-162 flexible FP-163 flexible
Parts Location (Shown on Page) 4-47 2 layers 2 layers 1 layer
Pattern Total Number of Layers Layers Not Indicated
DSC-P200 4-35
CD-517 FLEXIBLE
Note for Printed Wiring Board (See page 4-35). : Uses unleaded solder.
CD-517 FLEXIBLE BOARD
5 1 7 C -D < > IP
A
D104 SELF TIMER/ AF ILLUMINATOR
LND101 LND102 LND103 LND104 LND105 LND107 LND106 LND108 LND109 LND110 LND111 LND112 LND113 LND114 LND115 LND116 LND117 LND118 LND119 LND120 LND121 LND122 LND123 LND124 LND125 LND126 LND127 LND128 LND129 LND130 LND131 LND132 LND133 LND134 LND135 LND136 LND137 LND138 LND139 LND140 LND141 LND142 LND143 LND144 LND145
D104
K
-468-1 -815
A
K
D103
K A
D103 (AE/AF LOCK)
D102
A
D101
D101 (FLASH/CHG) Note: CD-517 flexible complete board and IC101 are not supplied, but there are included in CCD block assy.
B
45
C101 R101 R103 16 15 C R102 3 2 1
Q101 E
B
R109 C106
IC101 Q103
B C E C103 R105 C R104 C104 C107 C105 17 18 19 CL120 CL121 31 32 CL103 CL107 CL111 CL102 CL114
C
1
C102 B E
Q102
1-864-51805
11
1
2
3
4
DSC-P200 4-37 4-38
CD-517
Printed wiring boards of the CH-146, SY-123 boards are not shown. Pages from 4-39 to 4-42 are not shown.
DSC-P200
Note for Printed Wiring Board (See page 4-35).
FP-162 FLEXIBLE
: Uses unleaded solder.
FP-162 FLEXIBLE BOARD
LND149
J101
DC IN
4
Note: CN101 (multi connector) is not supplied, but this is included in FP-162 flexible complete board.
1-864112FP-162 >PI<
5
2
3
LND147
LND146
BT901 BATTERY TERMINAL
S
1
05
LND150
(MULTI CONNECTOR)
CN101 4 3 27 1 LF101 1 2 5 15 25 28
D101
2
10
20
26
1-864-112-
11
LND148
FP-163 FLEXIBLE
: Uses unleaded solder.
LND102 LND104 LND106 LND108 LND110 LND112 LND114 LND116 LND118 LND120 LND122 LND124 LND126 LND128 LND130 LND132 LND134 LND136 LND138 LND140 LND142 LND144
FP-163 FLEXIBLE BOARD
LND518 LND517 LND516 LND513 LND512 LND511 LND508 LND507 45
1 LND101 LND103 LND105 LND107 LND109 LND111 LND113 LND115 LND117 LND119 LND121 LND123 LND125 LND127 LND129 LND131 LND133 LND135 LND137 LND139 LND141 LND143 LND145
FLASH UNIT
XE H XE L
TRIG 300V TRIG GND
LND521
1-864-113FP-163
LND522
LND503 LND502 LND501
1
18
FX
1>PI<
LND524 LND523
C601 CHARGING CAPACITOR
CL502
05
1-864-113- 11
CL501
Note: FLASH UNIT and C601 are not included in FP-163 flexible board.
DSC-P200 4-43 4-44
+
FP-162, FP-163
Waveforms of the SY-123 board are not shown. Pages 4-45 and 4-46 are not shown.
DSC-P200
4-3. PRINTED WIRING BOARDS
4-5. MOUNTED PARTS LOCATION
CD-517 FLEXIBLE BOARD
C102 C105 C106 C107 D101 D103 D104 IC101 Q101 Q102 Q103 R101 R102 R103 R104 R105 R109 C-3 C-4 C-3 C-4 B-2 A-2 B-1 C-4 C-3 C-3 C-3 C-3 C-3 C-3 C-3 C-3 C-3
no mark : side A * mark : side B
DSC-P200 4-47
CD-517
Mounted parts location of the CH-146 and SY-123 boards are not shown. Page 4-48 and 4-49 are not shown.
DSC-P200
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
A
B
C
D
OVERALL ASSEMBLY
LENS BLOCK ASSEMBLY
MAIN BLOCK ASSEMBLY
BT BLOCK ASSEMBLY
Link
ELECTRICAL PARTS LIST
FP-162 FLEXIBLE BOARD FP-163 FLEXIBLE BOARD
C D
ACCESSORIES
CD-517 FLEXIBLE BOARD B FP-161 FLEXIBLE BOARD
C
DSC-P200
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
NOTE: · -XX, -X mean standardized parts, so they may have some differences from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · CAPACITORS: uF: µF · COILS uH: µH · RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable · SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... · Abbreviation AR : Argentina model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model HK : Hong Kong model JE : Tourist model KR : Korean model
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DSC-P200
5-1
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. OVERALL ASSEMBLY
3 7
Main block assembly (See Page 5-4)
8
3 3 4 5 2 6
Lens block assembly (See Page 5-3)
9
3 11 10
12 1
3
Ref. No. 1 2 2 2 3 4 5 6
Part No. 2-547-040-01 2-547-038-01 2-547-038-11 2-547-038-21 2-587-151-01
Description RING, LENS CABINET (FRONT (SD)) (SILVER) CABINET (FRONT (SD)) (BLACK) CABINET (FRONT (SD)) (BROWN) SCREW (M1.4), NEW TRUSTAR.P2
Ref. No. 7 8 9 9 9 10 11 12
Part No. 2-582-186-01 2-582-185-01 A-1097-047-A A-1097-048-A A-1097-049-A
Description SHEET, LCD WINDOW ADHESIVE WINDOW, LCD CABINET (REAR) BLOCK ASSY (SILVER) CABINET (REAR) BLOCK ASSY (BLACK) CABINET (REAR) BLOCK ASSY (BROWN)
2-582-197-01 SHEET (FRONT), ADHESIVE 2-582-196-01 SHEET, OVF WINDOW ADHESIVE 2-582-195-01 WINDOW, OVF
X-2048-862-1 CABINET ASSY, SIDE 2-582-194-01 CABINET (FRONT), INNER 2-582-184-01 PLATE, CABINET
DSC-P200 5-2
5. REPAIR PARTS LIST
5-1-2. LENS BLOCK ASSEMBLY
60
SP901
61
64
(including CD-517 flexible board and IC101 (CCD IMAGER)) (Note 2)
62 55
51
59 58 57
LCD901
53 52
(Note 1) (Note 1)
56
54
(Note 1) D901
63
Note 1: Be sure to read "2-3. Exchange Method of Barrier Assy" on page 2-7 when change Ref. No. 52, 53 and 54. Note 2: Be sure to read "Precuations for Replacement of CCD Imager" on page 4-8 when changing the CCD imager. Ref. No. 51 52 53 54 55 56 57 58 59 Part No. 1-788-208-11 3-091-427-01 3-086-156-31 X-3954-476-1 3-091-013-01 2-021-317-01 1-788-176-11 2-021-318-01 3-348-998-61 Description LENS, VIDEO (EC01B) RING (A), ORNAMENTAL (Note1) SCREW, TAPPING (P2) (Note1) BARRIER ASSY (Note1) HOLDER, AF MASK, LPF OPTICAL FILTERBLOCK (OFB-02-21) SEALGOM 890 SCREW (M1.4X4), TAPPING, PAN Ref. No. 60 61 62 63 64 Part No. 2-582-219-01 3-080-204-11 2-589-437-01 2-582-218-01 A-1089-498-A Description FRAME, LENS SCREW, TAPPING, P2 GUARD (CD), FLEXIBLE SHEET, BL HARNESS PROTECTION CCD BLOCK ASSY (including CD-517 flexible board and IC101 (CCD IMAGER)) (Note2)
D901 1-479-010-11 BLOCK, LIGHT GUIDE PLATE (2.0) LCD901 8-753-228-05 ACX335AK-3 SP901 1-825-923-31 LOUDSPEAKER (1.3CM)
DSC-P200 5-3
5. REPAIR PARTS LIST
5-1-3. MAIN BLOCK ASSEMBLY
ns: not supplied
MIC901
106
102
(including CP101 (CH-146 board) and IC301 (KWF board))
104
(Note 1)
111
J101 ns (CN101)
BT901
!
ns (BT001)
103
ns
105
(including BT001)
107 101 108
(Note 2)
106 110 112 109
ns
BT block assembly (See Page 5-5)
! BT001(BATTERY, LITHIUM SECONDARY)
CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Note 1: CN101 (multi connector) is not supplied, but this is included in FP-162 flexible complete board. Note 2: Part of 108 is including FP-161 flexible board. Ref. No. 101 102 Part No. Description
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. 0 104 105 106 107 108 109 110 111 112 0 BT901 Part No.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Description
102
102
102
3-080-222-31 SCREW (M1.7), TAPPING, P2 A-1107-528-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (E) A-1107-529-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (HK, KR, CH, JE) A-1107-533-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (US, CND, AUS) A-1107-534-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (AEP, UK) 2-582-200-01 SHEET, JK
A-1086-398-A FP-162 FLEXIBLE BOARD, COMPLETE (Note 1) 1-479-099-11 CONTROL SW BLOCK (SW51740) (Including BT001) 3-080-204-11 SCREW, TAPPING, P2 2-582-202-01 SHEET, CCD RADIATION 1-819-094-11 CONNECTOR, MEMORY STICK 10P (Note 2) 2-582-205-01 2-590-642-01 1-479-100-11 2-592-676-01 1-780-141-21 SHEET, MS RADIATION SHEET, SY RADIATION SWITCH BLOCK, CONTROL MS SPACER BATTERY TERMINAL BOARD
103
0 J101 1-817-331-11 DC JACK 5P (DC IN) MIC901 1-542-623-11 MICROPHONE UNIT
DSC-P200 5-4
5. REPAIR PARTS LIST
5-1-4. BT BLOCK ASSEMBLY
ns: not supplied
157
158
C601 (Note)
159 156
(Note)
152
153
ns
155 154 151
Note: FLASH UNIT and C601 are not included in FP-163 flexible board. Ref. No. 151 151 151 152 152 152 153 153 153 Part No. X-2048-864-1 X-2048-866-1 X-2048-867-1 2-547-035-01 2-547-035-11 2-547-035-21 2-547-036-01 2-547-036-11 2-547-036-21 Description HOLDER ASSY, BATTERY (SILVER) HOLDER ASSY, BATTERY (BLACK) HOLDER ASSY, BATTERY (BROWN) LID, DC JACK (SILVER) LID, DC JACK (BLACK) LID, DC JACK (BROWN) LID, BATTERY (SILVER) LID, BATTERY (BLACK) LID, BATTERY (BROWN)
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. 154 155 0 156 157 0 158 159 0 C601 Part No. 2-582-212-01 2-587-151-01 1-478-674-11 2-582-204-01 1-864-113-11
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Description SCREW, TRIPOD SCREW (M1.4), NEW TRUSTAR.P2 FLASH UNIT (Note) SHEET, STROBOSCOPE INSULATING FP-163 FLEXIBLE BOARD
2-590-582-01 SHEET, CAPACITOR INSULATING 1-100-969-11 CAP, ELECT 117uF
315V (Note)
DSC-P200
5-5
CD-517
Ref. No. Part No.
FP-161
Description
FP-162
FP-163
Ref. No. Part No. Description < LINE FILTER > LF101 1-456-681-21 COIL, CHOKE
5-2. ELECTRICAL PARTS LIST
A-1089-498-A CCD BLOCK ASSY (Not supplied) CD-517 FLEXIBLE BOARD, COMPLETE ******************************* (CCD block assy is including CD-517 flexible board and IC101 (CCD imager).) 0 < CAPACITOR > C102 C105 C106 C107 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP < DIODE > 0 C601 D101 D103 D104 8-719-077-34 DIODE SML-310YTT86 (FLASH/CHG) 8-719-075-29 DIODE SML-510MWT86S (AE/AF LOCK) 6-500-505-01 DIODE OPY5052 (SELF TIMER/AF ILLUMINATOR) < IC > IC101 (Not supplied) ICX489CQZ-13 (Note) < TRANSISTOR > Q101 Q102 Q103 6-550-119-01 TRANSISTOR 6-550-119-01 TRANSISTOR 8-729-050-22 TRANSISTOR < RESISTOR > R101 R102 R103 R104 R105 R109 1-218-935-11 1-218-966-11 1-218-958-11 1-218-954-11 1-218-955-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 33 12K 2.7K 1.2K 1.5K 0 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W DTC144EMT2L DTC144EMT2L 2SC4250 (T5LSONY1) 1-100-969-11 CAP, ELECT 117uF 315V 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 16V 16V 16V 16V
1-864-113-11 FP-163 FLEXIBLE BOARD ********************* (FLASH UNIT and C601 are not included in this flexible board.) 1-478-674-11 FLASH UNIT < CAPACITOR >
0
Electrical parts list of the CH-146 and SY123 boards are not shown. Pages 5-7 to 5-11 are not shown.
1-218-990-11 SHORT CHIP
1-819-094-11 CONNECTOR, MEMORY STICK 10P (Not supplied) FP-161 FLEXIBLE BOARD **************************** (Memory stick connector is including FP-161 flexible board.)
0
A-1086-398-A FP-162 FLEXIBLE BOARD, COMPLETE ****************************** (This flexible complete board is including CN101 (multi connector).) 1-780-141-21 BATTERY TERMINAL BOARD < CONNECTOR > CN101 (Not supplied) CONNECTOR, MULTIPLE (SOCKET) < DIODE > D101 8-719-056-23 DIODE MA2S111-(K8).SO < JACK >
0 BT901
0 J101
1-817-331-11 DC JACK 5P (DC IN)
(Note) Be sure to read "Precautions for Replacement of CCD Imager" on page 4-8 when changing the CCD imager. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DSC-P200 5-6
Checking supplied accessories.
Power cord (1) 0 1-769-608-31 (AEP, E) 0 1-782-476-13 (CH) 0 1-783-374-12 (UK, HK) 0 1-790-107-22 (US, CND) 0 1-790-732-12 (JE) 0 1-823-947-12 (KR) 0 1-827-945-12 (AUS)
AC adaptor AC-LS5/LS5B (1) 0 1-477-730-51
Other accessories
2-582-853-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (EXCEPT AEP, KR, CH) 2-582-853-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND, AEP) 2-582-853-31 INSTRUCTION (READ THIS FIRST) (SPANISH, PORTUGUESE) (AEP, E, JE) 2-582-853-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH) (AEP) 2-582-853-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-582-853-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN, SWEDISH) (AEP) 2-582-853-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) 2-582-853-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) 2-582-853-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH) (AEP) 2-582-854-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN, SLOVAKIAN) (AEP) 2-582-856-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (EXCEPT AEP, AR, KR, BR, CH) 2-582-856-21 INSTRUCTION (USER'S GUIDE) (FRENCH, ITALIAN) (CND, AEP) 2-582-856-31 INSTRUCTION (USER'S GUIDE) (SPANISH, PORTUGUESE) (AEP, E, JE) 2-582-856-41 INSTRUCTION (USER'S GUIDE) (GERMAN, DUTCH) (AEP) 2-582-856-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-582-856-61 INSTRUCTION (USER'S GUIDE) (RUSSIAN, SWEDISH) (AEP) 2-582-856-71 INSTRUCTION (USER'S GUIDE) (ARABIC, PERSIAN) (E) 2-582-856-81 INSTRUCTION (USER'S GUIDE) (KOREAN) (KR, JE) 2-582-856-91 INSTRUCTION (USER'S GUIDE) (POLISH, CZECH) (AEP) 2-582-857-11 INSTRUCTION (USER'S GUIDE) (HUNGARIAN, SLOVAKIAN) (AEP)
NP-FR1 battery pack (1) (not supplied)
Wrist strap (1) 2-050-981-01
USB, AV cable for multi-use terminal (1) 1-829-866-11
"Memory Stick" (32MB) (1) (not supplied)
CD-ROM (Cyber-shot application software) (1) 2-583-852-01 (US) 2-583-853-01 (CND, AEP, UK, E, HK, KR, AUS, JE) 2-583-854-01 (CH)
Conversion adaptor (1) 0 1-569-008-21 (E)
Conversion adaptor (1) 0 1-569-007-11 (E, JE)
Battery case (1) (not supplied)
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DSC-P200 5-12E
DSC-P200
LEVEL
2
SERVICE MANUAL
Ver 1.1 2005.02
SUPPLEMENT-1
File this supplement with the service manual.
(PV04-027)
US Model Canadian Model AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model
· Addition of Red Model · Change of Repair Parts · Addition of Argentine and Brazilian Models
· Addition of Red Model
This supplement covers only differences from models other than red. Refer to the parts list of original service manual about other parts.
5-1. EXPLODED VIEWS
Page
Ref. No. Part No. 2 9 10 151 152 153
Red model
Description 2-547-039-11 CABINET (FRONT (K)) (RED) A-1110-132-A CABINET (REAR) BLOCK ASSY (RED) X-2055-298-1 CABINET ASSY, SIDE (RED) X-2055-277-1 HOLDER ASSY, BATTERY (RED) 2-547-035-31 LID, DC JACK (RED) 2-547-036-31 LID, BATTERY (RED)
5-2
5-5
DSC-P200
9-876-854-82
Sony EMCS Co.
2005B0500-1 © 2005.2 Published by DI Technical Support Section
· Change of Repair Parts · Addition of Argentine and Brazilian Models
5-1. EXPLODED VIEWS
&: Points added portion. -: Points changed portion.
Page
Ref. No. Part No. 1
Former
Description Ref. No. Part No. 1 2-547-040-01 RING, LENS
New
Description 2-547-040-02 RING, LENS
5-2
[
102
5-4
A-1107-528-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (E)
102
A-1107-528-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (E, AR, BR)
)
· Abbreviation AR : Argentine model BR : Brazilian model
DSC-P200 --2--
&: Points added portion. -: Points changed portion. !: Points deleted portion.
Checking supplied accessories.
Other accessories
Power cord (1) 0 1-769-608-31 (AEP, E) 0 1-782-476-13 (CH) 0 1-783-374-12 (UK, HK) 0 1-790-107-22 (US, CND) 0 1-790-732-12 (JE) 0 1-823-947-12 (KR) 0 1-827-945-12 (AUS) 0 1-783-952-11 (AR) AC adaptor AC-LS5/LS5B (1) 0 1-477-730-71 2-582-853-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (EXCEPT AEP, KR, CH) 2-582-853-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND, AEP) 2-582-853-31 INSTRUCTION (READ THIS FIRST) (SPANISH, PORTUGUESE) (AEP, E, AR, JE) 2-582-853-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH) (AEP) 2-582-853-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE)
[
*
)
NP-FR1 battery pack (1) (not supplied)
Wrist strap (1) 2-050-981-01
2-582-853-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN, SWEDISH) (AEP) 2-582-853-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) 2-582-853-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) 2-582-853-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH) (AEP) 2-582-854-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN, SLOVAKIAN) (AEP) 2-582-856-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (EXCEPT AEP, AR, KR, BR, CH) 2-582-856-21 INSTRUCTION (USER'S GUIDE) (FRENCH, ITALIAN) (CND, AEP) 2-582-856-31 INSTRUCTION (USER'S GUIDE) (SPANISH, PORTUGUESE) (AEP, E, AR, JE)
USB, AV cable for multi-use terminal (1) 1-829-866-11
"Memory Stick" (32MB) (1) (not supplied)
Conversion adaptor (1) CD-ROM (Cyber-shot application software) (1) 0 1-569-008-21 (E) 2-583-852-01 (US) 2-583-853-01 (CND, AEP, UK, E, HK, KR, AUS, AR, BR, CH, JE) 2-583-854-01 (CH)
2-582-856-41 INSTRUCTION (USER'S GUIDE) (GERMAN, DUTCH) (AEP) 2-582-856-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-582-856-61 INSTRUCTION (USER'S GUIDE) (RUSSIAN, SWEDISH) (AEP) 2-582-856-71 INSTRUCTION (USER'S GUIDE) (ARABIC, PERSIAN) (E) 2-582-856-81 INSTRUCTION (USER'S GUIDE) (KOREAN) (KR, JE) 2-582-856-91 INSTRUCTION (USER'S GUIDE) (POLISH, CZECH) (AEP) 2-582-857-11 INSTRUCTION (USER'S GUIDE) (HUNGARIAN, SLOVAKIAN) (AEP)
)
$
)
Conversion adaptor (1) 0 1-569-007-11 (E, JE)
Battery case (1) (not supplied)
· Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model
CND : Canadian model HK : Hong Kong model JE : Tourist model KR : Korean model
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
DSC-P200 --3--
DSC-P200
LEVEL
2
SERVICE MANUAL
Ver 1.2 2005.05
SUPPLEMENT-2
File this supplement with the service manual.
(PV04-030)
US Model Canadian Model AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Japanese Model
· Addition of Japanese Model
· Addition of Japanese Model
This supplement covers only differences from models other than Japanese. Refer to the parts list of original service manual about other parts.
DSC-P200
9-876-854-85
Sony EMCS Co.
2005E0500-1 © 2005.5 Published by DI Technical Support Section
· Language that can be selected about SY-123 board
GP1 GP2
J US CND AUS Vietnam AEP UK E AR BR TW JE HK CH KR
z
GP3
GP4
GP5
&: Points added portion. !: Points deleted portion.
5-1. EXPLODED VIEWS
Page Former New
Japanese English French German Spanish Italian Portugal Simplified Chinese Traditional Chinese Arabic Dutch Russian Swedish Korean
z z z z z z z z z z z z z z z z z z z z z z z z z z z
Area
108
(Note 2)
108
(Note 2)
106 110 112
5-4
Ref. No. Part No. 102 Description
106 109
ns
#
110 112
Description
109
ns
Ref. No. Part No. 102
102
102
102
A-1107-528-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (E, AR, BR) A-1107-529-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (HK, KR, CH, JE) A-1107-533-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (US, CND, AUS) A-1107-534-A SY-123 BOARD, COMPLETE (SERVICE) (including CP101 (CH-146 board) and IC301 (KWF board)) (AEP, UK)
102
102
102
102
A-1107-528-A SY-123 BOARD, COMPLETE (SERVICE) (GP4) (including CP101 (CH-146 board) and IC301 (KWF board)) (E, AR, BR) A-1107-529-A SY-123 BOARD, COMPLETE (SERVICE) (GP5) (including CP101 (CH-146 board) and IC301 (KWF board)) (HK, KR, CH, JE) A-1107-533-A SY-123 BOARD, COMPLETE (SERVICE) (GP2) (including CP101 (CH-146 board) and IC301 (KWF board)) (US, CND, AUS) A-1107-534-A SY-123 BOARD, COMPLETE (SERVICE) (GP3) (including CP101 (CH-146 board) and IC301 (KWF board)) (AEP, UK) A-1127-721-A SY-123 BOARD, COMPLETE (SERVICE) (GP1) (including CP101 (CH-146 board) and IC301 (KWF board) (J)
& & & &
110
2-590-642-01 SHEET, SY RADIATION
) @
--2--
DSC-P200
&: Points added portion. -: Points changed portion.
Checking supplied accessories.
]
Power cord (1) 0 1-782-476-13 (CH) 0 1-783-374-12 (UK, HK) 0 1-790-107-22 (US, CND) 0 1-790-732-12 (JE, J) 0 1-823-946-12 (AEP, E) AC adaptor AC-LS5/LS5B (1) 0 1-477-730-81
Other accessories
2-582-853-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (EXCEPT AEP, KR, CH) 2-582-853-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND, AEP) 2-582-853-31 INSTRUCTION (READ THIS FIRST) (SPANISH, PORTUGUESE) (AEP, E, AR, JE) 2-582-853-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH) (AEP) 2-582-853-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-582-853-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN, SWEDISH) (AEP) 2-582-853-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) 2-582-853-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) 2-582-853-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH) (AEP) 2-582-854-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN, SLOVAKIAN) (AEP) 2-582-856-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (EXCEPT AEP, AR, KR, BR, CH) 2-582-856-21 INSTRUCTION (USER'S GUIDE) (FRENCH, ITALIAN) (CND, AEP) 2-582-856-31 INSTRUCTION (USER'S GUIDE) (SPANISH, PORTUGUESE) (AEP, E, AR, JE) 2-582-856-41 INSTRUCTION (USER'S GUIDE) (GERMAN, DUTCH) (AEP) 2-582-856-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-582-856-61 INSTRUCTION (USER'S GUIDE) (RUSSIAN