Text preview for : Service Bulletin OST-F1124-1.PDF part of DENON Service Bulletin OST-F1124-1 DENON DVD Video Player DVD Video Player Denon - DVD-2930 & 2930CI Service Bulletin OST-F1124-1.PDF
Back to : Service Bulletin OST-F112 | Home
100 Corporate Drive Mahwah, NJ 07430
Service Bulletin
No. : OST-F1124-1
Date: January 20, 2010
_____________________________________________________________
Model: DVD-2930CI
Subject: Firmware update.
Symptom: (1) Sound interrupts between tracks with specific "DVD-AUDIO-
DISC".
(2) When the units power is turned OFF and ON and "setting of HDMI" is set to
other than "HDMI OFF", setting of "DNR" is initialized to "0". (Even if OSD shows
"+3" etc. DNR is in fact set to "0".)
(3) If the user changes M1 ... M5 in the picture adjust menu the NOISE
REDUCTION (+1 ... +3) setting - the player "forgets" this setting when it is
switched off. That is - when switching it on again the menu still shows that M1 ...
M5 is active and NOISE REDUCTION setting is displayed to be on the adjusted
level (+1 ... +3) - but it is NOT (actual noise reduction setting is 0)
(4) If the player connected to specified HDMI-equipment (EDID is more than 3
block) during "setting of HDMI" is set to other than "HDMI OFF", audio signal may
be not output even if video the signal is output.
(5) When the resolution is changed from 480i to 480p or changed from VGA to
XGA under following condition, HDMI connect between DVD-2930(CI) to AV
amplifier becomes "Unlock".
[Condition] *HDMI setting is set to "MULTI (NORMAL)" or "MULTI (LPCM) ". *The
DVD player connects with AV amplifier. *The DVD player plays "96kHz 5.1ch" of
DVD-AUDIO.
(6) When a "96kHz, 5.1ch DVD-AUDIO" disc is played after playing a "96/24
(5.1ch) DTS signal of DVD-AUDIO" under following condition, HDMI connect
between DVD-2930 (CI) to AVR-5805 becomes "Unlock".
[Condition] *HDMI setting is set to "MULTI (NORMAL) ". *The player connects
with AVR-5805.
(7) 5.1ch Analog audio is not down-mixed and only audio signal of FL/FR is
outputted under following condition.
______________________________________________________________________________________
CONFIDENTIALITY NOTICE:
The information contained in this document is intended for the exclusive use by DENON Authorized Service Centers and their
employees. This document may contain information that is privileged, confidential and may be protected from disclosure under
applicable laws and terms of the DENON Service Agreement. Any distribution, disclosure, dissemination or copying of this
document and the information it contains is prohibited. No responsibility will be accepted by DENON for any damage, injury or loss
resulting from the misuse of the information contained in this document.
[Condition] *HDMI setting is set to "MULTI (NORMAL)" or "MULTI (LPCM) ". *The
player connects with HDMI monitor which has 2ch audio output.
(8) When playing an SACD disc that has more than 100 minutes of total recorded
time, "A0" is indicated to "time" in the OSD.
(9) When an SACD "Hybrid disc" is loaded, the player may only recognize it as a
"CD".
(10) If you push the "play button" of the player under following conditions, the unit
can not accept any button.
[Condition] *The player into "Resume Stop" by pushing "STOP button"
immediately after displayed "indicator of DVD-AUDIO" after load "DVD-AUDIO
disc".
(11) Indicate wrong playing time under following condition.
[Condition] *Load "MP3 and WMA mixed disc" to the player, -> pause the unit
during play "MP3 track", -> search "WMA track", -> re-search to the same "MP3
track", -> then play the MP3 track.
(12) If pushing the "" cursor button on RC-unit once after pushed "" button
several times (more than 10 times or 20 times) then pushing the "ENTER button"
in "Setting the slide switching time" in "SET UP", the player freeze.
Solution: The Back-end software has been improved.
Please record a Folder (Name of the Folder: DVD_2930) and include the
D293SAVD.ROM file. Burn it onto a blank CD-R separately and use the disc to
update the Back-end firmware.
Cautions: