Text preview for : NSX-SZ6.pdf part of aiwa nsx-sz6 sound system
Back to : NSX-SZ6.part1.rar | Home
NSX-SZ6
LH
SERVICE MANUAL
COMPACT DISC STEREO SYSTEM
SYSTEM NSX-SZ6 CD CASSEIVER CX-NSZ6 SPEAKER SX-NSZ1 REMOTE CONTROLLER RC-AAS08
BASIC TAPE MECHANISM : ZZM-2 YPR1NC BASIC CD MECHANISM : KSM-213 CDM
S/M Code No. 09-00C-433-8S3
DA TA
SPECIFICATIONS
Tuning range Usable sensitivity (IHF) Antenna terminals Tuning range Usable sensitivity Antenna Power output 87.5 MHz to 108 MHz 13.2 dBf 75 ohms (unbalanced) Laser Semiconductor laser ( =780 nm) Speaker system Speaker units Impedance Dimensions (W x H x D) Weight Power requirements Rated: 4 W + 4 W (6 ohms, T.H.D. 1 %, 1 kHz) Reference: 5 W + 5 W (6 ohms, T.H.D. 10 %, 1 kHz) 0.2 % (1 W, 1 kHz, 6 ohms, DIN AUDIO) VIDEO/AUX: 600 mV SPEAKERS: 6 ohms or more PHONES: 32 ohms or more Power consumption Dimensions (W x H x D) Weight
530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) 350 µV/m Loop antenna
1 way, bass reflex Full range: 100 mm cone 6 ohms 200 x 288 x 186 mm 1.5 kg
120 V/ 220 - 230 V/ 240 V AC (switchable), 50 Hz/ 60Hz 28 W 260 x 295 x 260 mm 3.4 kg
Total harmonic distortion Inputs Outputs
· Specifications and external appearance are subject to change without notice.
Track format Frequency response Recording system Heads
4 tracks, 2 channels stereo 50 Hz 8000 Hz AC bias Deck 1: recording/playback x 1, erase x 1 Deck 2: playback x 1
ACCESSORIES / PACKAGE LIST
REF. NO. PART NO. 1 2 3 4
KANRI DESCRIPTION NO. 8A-NED-912-010 IB,LH(P)CCE -SZ6 8A-NEC-701-010 RC UNIT,RC-AAS08 87-043-115-010 ANT,FEEDER FM 87-A90-030-010 ANT,LOOP AM-NC C
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in hazardous radiation exposure.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel: Usynlig laserstOEling ved OEbning, nOEr sikkerhedsafbrydere er ude af funktion. UndgOE uds¾ttelse for strOEling.
ATTENTION
LÕutillisation de commandes, rZ glages ou procZ dures autres que ceux spZ s peut entra"ner une dangereuse cifiZ exposition aux radiations.
ADVARSEL
Usynlig laserstOEling ved OEbning, nOEr sikkerhedsafbrydereer ude af funktion. UndgOE uds¾ttelse for strOEling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
s
VAROITUS!
Laiteen KSyttSminen muulla kuin tSssS kSyttsohjeessa mainitulla tavalla saataa altistaa kSyt-tSjSn turvallisuusluokan 1 ylittSvSlle nSkymSttsmSlle lasersSteilylle. VARNING! Om apparaten anvSnds pOE annat sStt Sn vad som specificeras i denna bruksanvising, kan anvSndaren utsSttas fsr osynling laserstrOElning, som sverskrider grSnsen fsr laserklass 1.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
Precaution to replace Optical block
(KSS-213C)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.
PICK-UP Assy P.W.B
1) After the connection, remove solder shown in right figure. Solder
3
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
1 Remove the AC power cord. 2 Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 3 Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 4 Contact the same end of the discharging resistor as step 3 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) 5 Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope.
MAIN C.B D101
3
C101
C102
4
2
2
Select a discharging resistor referring to the following table. Charging voltage (V) (C101, 102) 25-48 49-140 Discharging resistor () 100 220 Rated power (W) 3 5 Parts number 87-A00-247-090 87-A00-232-090
Fig-1
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is "H", the MICROCOMPUTER is judged to be operating correctly. When this terminal is "L", the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go "L" when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to "L".
· Good or no good judgement of the MICROCOMPUTER
1 Turn on the AC main power. 2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the "H" level or not. 3 When the HOLD terminal is "L" level, the abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good.
4
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no good of the MICROCOMPUTER. 1 Remove the AC power cord.
TE R
RO
CO
M
PU
FRONT C.B % VSS MICROC113 COMPUTER * VDD
M
18 15
IC
C113 FRONT C.B
Short with tweezers.
Fig-2-2
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
5
ELECTRICAL MAIN PARTS LIST
REF. NO. PART NO. IC 87-A21-591-010 87-A21-722-010 87-A21-419-040 8A-NEC-602-010 87-070-083-010 87-A21-443-040 87-A21-560-010 87-070-127-110 87-A21-381-040 TRANSISTOR 87-026-609-080 89-213-702-010 87-026-610-080 87-A30-076-080 87-A30-282-040 87-A30-075-080 87-A30-256-010 87-A30-255-010 87-A30-090-080 87-A30-091-080 87-A30-062-080 87-A30-318-080 87-A30-492-080 87-A30-234-080 87-A30-521-080 87-A30-489-080 89-503-602-080 89-327-143-080 DIODE 87-A40-553-080 87-A40-777-080 87-020-465-080 87-A40-764-080 87-A40-313-080 87-A40-269-080 87-A40-270-080 87-A40-758-080 87-A40-747-080 87-A40-743-080 87-A40-749-080 87-A40-739-080 87-A40-748-080 87-A40-760-080 87-A40-455-090 MAIN C.B C9 C10 C11 C12 C21 C22 C23 C25 C26 C31 C32 C34 C35 C36 C50 C51 C60 C61 87-010-759-080 87-010-759-080 87-010-759-080 87-010-759-080 87-A12-442-000 87-A10-831-080 87-010-387-080 87-010-408-080 87-010-408-080 87-010-759-080 87-012-286-080 87-010-260-080 87-010-406-080 87-010-112-080 87-010-247-080 87-010-247-080 87-010-403-080 87-010-260-080
KANRI NO.
DESCRIPTION
REF. NO. PART NO. C101 C102 C103 C104 C105 C106 C107 C108 C111 C112 C113 C114 C117 C118 C119 C120 C125 C126 C127 C128 C140 C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C331 C332 C333 C334 C335 C336 C337 C338 C339 C340 C341 C342 C344 C345 C346 C347 C348 C349 C350 C351 C352 C353 C354 C355 C356 C357 C358 C359 C360 C361 C362 C363 C371 C372 C373 C374 87-012-284-080 87-012-284-080 87-010-544-080 87-010-544-080 87-012-282-080 87-012-282-080 87-010-403-080 87-010-403-080 87-010-406-080 87-010-406-080 87-012-195-080 87-012-195-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-286-080 87-010-759-080 87-010-759-080 87-010-759-080 87-010-759-080 87-010-190-080 87-010-374-080 87-010-759-080 87-010-260-080 87-010-260-080 87-012-286-080 87-010-405-080 87-010-263-080 87-012-349-080 87-010-546-080 87-010-401-080 87-012-193-080 87-012-286-080 87-010-260-080 87-A10-504-080 87-010-401-080 87-010-759-080 87-010-759-080 87-010-260-080 87-012-195-080 87-010-759-080 87-012-282-080 87-A10-504-080 87-012-195-080 87-010-260-080 87-012-286-080 87-010-260-080 87-012-286-080 87-010-248-080 87-012-286-080 87-010-263-080 87-012-286-080 87-012-176-080 87-012-176-080 87-010-404-080 87-012-286-080 87-010-401-080 87-010-759-080 87-010-759-080 87-010-759-080 87-010-405-080 87-012-195-080 87-012-349-080 87-010-544-080 87-010-544-080 87-010-759-080 87-010-221-080 87-010-759-080 87-010-544-080 87-010-236-080
C-IC,LC78641NE-D IC,LA6548D C-IC,NJM14558MD-TE2 C-IC,M38B57MCH-E249FP IC,GP1U281X C-IC,M62495AFP IC,LA1844L-A IC,LC72131 D C-IC,LA9235M
KANRI NO. CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP,
DESCRIPTION U 6800P-50 U 6800P-50 ELECT 0.1-50V ELECT 0.1-50V U 4700P-50 U 4700P-50 ELECT 3.3-50V ELECT 3.3-50V ELECT 22-50 ELECT 22-50
TR,KTA1266GR TR,2SB1370 (1.8W) TR,KTC3198GR C-TR,2SC3052F C-TR,DTA114TKA C-TR,2SA1235F TR,2SD1933 TR,2SB1342 FET,2SK2541 FET,2SJ460 C-TR,KRC104S TR,CSA952K TR,2SC5343G TR,CSC4115BC C-TR,2SC5345S(O) C-TR,KRA107S C-FET,2SK360E C-TR,2SC27140
C-CAP,U 100P-50CH C-CAP,U 100P-50CH CAP, U 0.01-25 CAP, U 0.01-25 CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F S CHIP F 0.01 CAP, ELECT 47-10V C-CAP,U, 0.1-25F CAP, ELECT 47-25V CAP, ELECT 47-25V CAP, U 0.01-25 CAP, ELECT 10-50V CAP, ELECT 100-10V C-CAP,S 1000P-50 CH CAP, ELECT 0.33-50V CAP, ELECT 1-50V C-CAP,U 82P-50 CH CAP, U 0.01-25 CAP, ELECT 47-25V C-CAP,U 0.047-16 K B CAP, ELECT 1-50V C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F CAP, ELECT 47-25V C-CAP,U 100P-50CH C-CAP,U, 0.1-25F CAP, U 4700P-50 C-CAP,U 0.047-16 K B C-CAP,U 100P-50CH CAP, ELECT 47-25V CAP, CAP, CAP, CAP, CAP, U 0.01-25 ELECT 47-25V U 0.01-25 ELECT 220-10V U 0.01-25
DIODE,1N4003 LES ZENER,UZ30BSB DIODE,1SS133 (110MA) ZENER,UZ10BSC C-DIODE,MC 2840 C-DIODE,MC2836 C-DIODE,MC2838 ZENER,UZ8.2BSB ZENER,UZ5.1BSB ZENER,UZ4.3BSA ZENER,UZ5.6BSB ZENER,UZ2.7BSA ZENER,UZ5.6BSA ZENER,UZ9.1BSA DIODE,RL203 GW
C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F CAP,E 3300-25 M SMG CAP,E 1000-25 M SMG CAP,E 470-25 SME CAP, ELECT 47-50V CAP, ELECT 47-50V C-CAP,U, 0.1-25F CAP, CAP, CAP, CAP, CAP, U 0.01-25 ELECT 47-25V ELECT 22-50 ELECT 100-16V ELECT 100-50V
CAP, ELECT 100-10V CAP, U 0.01-25 CAP 15P CAP 15P CAP, ELECT 4.7-50V CAP, U 0.01-25 CAP, ELECT 1-50V C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F CAP, ELECT 10-50V C-CAP,U 100P-50CH C-CAP,S 1000P-50 CH CAP, ELECT 0.1-50V CAP, ELECT 0.1-50V C-CAP,U, 0.1-25F CAP, ELECT 470-10V C-CAP,U, 0.1-25F CAP, ELECT 0.1-50V CAP,E 1000-10 SME
CAP, ELECT 100-50V CAP, ELECT 3.3-50V CAP, ELECT 47-25V
6
REF. NO. PART NO. C375 C376 C377 C378 C379 C380 C381 C391 C392 C393 C394 C395 C396 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C421 C422 C423 C424 C425 C426 C427 C428 C429 C430 C431 C432 C433 C434 C435 C441 C442 C445 C452 C453 C454 C455 C456 C457 C460 C461 C462 C470 C605 C606 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C630 C671 C672 C677 87-010-759-080 87-010-263-080 87-010-759-080 87-010-759-080 87-010-759-080 87-010-759-080 87-010-759-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-010-759-080 87-010-759-080 87-012-193-080 87-012-193-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-278-080 87-012-278-080 87-010-405-080 87-010-405-080 87-010-197-080 87-012-275-080 87-012-275-080 87-012-274-080 87-012-274-080 87-010-263-080 87-010-263-080 87-012-188-080 87-012-188-080 87-010-598-080 87-010-598-080 87-012-284-080 87-012-284-080 87-010-546-080 87-010-546-080 87-010-263-080 87-010-759-080 87-010-759-080 87-A10-039-080 87-010-382-080 87-012-279-080 87-012-279-080 87-012-279-080 87-012-286-080 87-A12-361-080 87-010-759-080 87-012-158-080 87-012-158-080 87-A10-039-080 87-012-275-080 87-012-275-080 87-010-785-080 87-010-785-080 87-010-545-080 87-010-545-080 87-010-545-080 87-010-545-080 87-012-172-080 87-010-248-080 87-010-221-080 87-010-405-080 87-010-831-080 87-010-831-080 87-010-831-080 87-012-286-080
KANRI DESCRIPTION NO. C-CAP,U, 0.1-25F CAP, ELECT 100-10V C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U 82P-50 CH C-CAP,U 82P-50 CH CAP, U 0.01-25 CAP, U 0.01-25 CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U 2200P-50 B C-CAP,U 2200P-50 B CAP, ELECT 10-50V CAP, ELECT 10-50V CAP, CHIP 0.01 DM C-CAP,U 1200P-50 B C-CAP,U 1200P-50 B CHIP CAP,U 1000P-50B CHIP CAP,U 1000P-50B CAP, ELECT 100-10V CAP, ELECT 100-10V C-CAP,U 47P-50 CH C-CAP,U 47P-50 CH C-CAP,S 0.068-16VRK C-CAP,S 0.068-16VRK CAP, U 6800P-50 CAP, U 6800P-50 CAP, ELECT 0.33-50V CAP, ELECT 0.33-50V CAP, ELECT 100-10V C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F C-CAP,U 470P-50 J CH CAP, ELECT 22-25V C-CAP,U 2700P-50 B C-CAP,U 2700P-50 B C-CAP,U 2700P-50 B CAP, U 0.01-25 CAP,M 5600P-100 J CP C-CAP,U, 0.1-25F C-CAP,S 390P-50 CH C-CAP,S 390P-50 CH C-CAP,U 470P-50 J CH C-CAP,U 1200P-50 B C-CAP,U 1200P-50 B C-CAP,U0.015-25BK C-CAP,U0.015-25BK CAP, ELECT 0.22-50V CAP, ELECT 0.22-50V CAP, ELECT 0.22-50V CAP, ELECT 0.22-50V CAPACITOR CHIP U 10P CH CAP, ELECT 220-10V CAP, ELECT 470-10V CAP, ELECT 10-50V C-CAP,U 0.1-16 Z F C-CAP,U,0.1-16F C-CAP,U,0.1-16F CAP, U 0.01-25
REF. NO. PART NO. C771 C772 C782 C783 C784 C785 C786 C788 C789 C790 C791 C792 C793 C795 C796 C797 C798 C799 C800 C801 C802 C803 C804 C807 C808 C809 C810 C814 C815 C816 C821 C823 C824 C825 C836 C837 C842 C844 C850 C851 C852 C853 C858 C859 C860 C902 C908 C909 C911 C912 C913 C914 C915 C918 C920 C921 C922 C923 C924 C927 C961 C962 C971 C972 C973 C974 C979 C981 C982 C983 87-010-263-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-167-080 87-A12-052-080 87-A12-052-080 87-010-759-080 87-012-286-080 87-010-404-080 87-012-286-080 87-012-286-080 87-010-405-080 87-012-286-080 87-010-407-080 87-010-829-080 87-010-403-080 87-010-829-080 87-010-787-080 87-010-263-080 87-010-400-080 87-010-401-080 87-010-401-080 87-010-759-080 87-012-286-080 87-010-400-080 87-010-400-080 87-010-405-080 87-010-177-080 87-010-404-080 87-010-596-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-286-080 87-010-260-080 87-012-286-080 87-012-286-080 87-012-286-080 87-010-759-080 87-010-759-080 87-012-286-080 87-018-145-080 87-012-174-080 87-012-349-080 87-012-170-080 87-012-195-080 87-012-286-080 87-012-286-080 87-012-286-080 87-012-165-080 87-012-180-080 87-012-186-080 87-012-174-080 87-012-270-080 87-012-174-080 87-012-195-080 87-012-170-080 87-010-401-080 87-010-381-080 87-010-404-080 87-012-286-080 87-012-286-080 87-012-195-080 87-010-260-080 87-010-759-080 87-012-286-080
KANRI NO. CAP, CAP, CAP, CAP, CAP,
DESCRIPTION ELECT 100-10V U 0.01-25 U 0.01-25 U 0.01-25 U 0.01-25
CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U 5P-50 CH C-CAP,S 0.033-25 J B C-CAP,S 0.033-25 J B C-CAP,U, 0.1-25F CAP, U 0.01-25 CAP, ELECT 4.7-50V CAP, U 0.01-25 CAP, U 0.01-25 CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, ELECT 10-50V U 0.01-25 ELECT 33-50V U 0.047-16 ELECT 3.3-50V U 0.047-16 U 0.022-25 ELECT 100-10V ELECT 0.47-50V ELECT 1-50V
CAP, ELECT 1-50V C-CAP,U, 0.1-25F CAP, U 0.01-25 CAP, ELECT 0.47-50V CAP, ELECT 0.47-50V CAP, ELECT 10-50V C-CAP,S 820P-50 SL CAP, ELECT 4.7-50V CAP, S 0.047-16 CAP, U 0.01-25 CAP, CAP, CAP, CAP, CAP, U 0.01-25 U 0.01-25 U 0.01-25 ELECT 47-25V U 0.01-25
CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U, 0.1-25F C-CAP,U, 0.1-25F CAP, U 0.01-25 CAP, TC U 6.8P-50 K CH UP050 CAP CHIP CERA SS 12P CHJ C-CAP,S 1000P-50 CH C-CAP,U 8P-50 CH C-CAP,U 100P-50CH CAP, U 0.01-25 CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U 3P-50 CK C-CAP,U 22P-50 CH C-CAP,U 39P-50 CH CAP CHIP CERA SS 12P CHJ C-CAP,U 470P-50 K B CAP CHIP CERA SS 12P CHJ C-CAP,U 100P-50CH C-CAP,U 8P-50 CH CAP, ELECT 1-50V CAP, ELECT 330-16V CAP, ELECT 4.7-50V CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U 100P-50CH CAP, ELECT 47-25V C-CAP,U, 0.1-25F CAP, U 0.01-25
7
REF. NO. PART NO. C984 C985 C987 C989 C990 C991 C992 C993 C994 C995 C996 C997 C998 C999 CF831 CF832 CN301 CN302 CN351 CN401 CNA351 CNA401 D902 D903 F101 FC101 FC102 FFC201 FFC301 FFC302 J101 J103 J602 J831 JW1 JW2 JW134 L101 L102 L451 L801 L802 L811 L832 L903 L906 L907 L908 L951 PT101 R790 RY101 S1 T101 T102 X301 X991 FRONT C.B 87-012-286-080 87-012-195-080 87-012-286-080 87-012-286-080 87-012-195-080 87-012-176-080 87-012-176-080 87-012-274-080 87-012-195-080 87-012-274-080 87-012-195-080 87-010-759-080 87-010-260-080 87-A11-155-080 87-008-261-010 87-008-261-010 87-A60-424-010 8A-NED-608-010 87-A60-625-010 87-A60-620-010 8A-NEC-634-010 8A-NEC-633-010 87-A40-916-040 87-A40-916-040 87-035-360-010 87-A90-505-080 87-A90-505-080 88-905-151-110 8A-NEC-603-010 88-906-151-110 87-A60-602-010 87-A61-452-010 87-A60-881-010 87-A60-202-010 87-A90-093-080 87-A90-093-080 87-008-372-080 87-A50-610-010 87-A50-610-010 87-007-342-010 87-A50-608-010 87-A91-551-010 87-005-847-080 87-005-847-080 88-ZA1-602-110 87-005-847-080 8A-NEC-611-010 88-ZA1-624-010 8A-NF8-667-010 8A-NEC-609-010 87-012-286-080 87-045-389-010 87-A90-165-010 87-A60-317-010 87-A60-317-010 87-A70-046-010 87-A70-061-010
KANRI DESCRIPTION NO. CAP, U 0.01-25 C-CAP,U 100P-50CH CAP, U 0.01-25 CAP, U 0.01-25 C-CAP,U 100P-50CH CAP 15P CAP 15P CHIP CAP,U 1000P-50B C-CAP,U 100P-50CH CHIP CAP,U 1000P-50B C-CAP,U 100P-50CH C-CAP,U, 0.1-25F CAP, ELECT 47-25V CAP,TC U 0.01-16 Z F FILTER, SFE10.7MA5-A FILTER, SFE10.7MA5 CONN,16P V TOC-B CONN,ASSY,6P CONN,8P V 2MM JMT CONN,3P V 2MM JMT CONN ASSY,8P RPB CONN ASSY,3P (PH) C-VARI-CAP,HVC202A C-VARI-CAP,HVC202A FUSE 630MA 250V T FUSE CLAMP,TP00351-51 FUSE CLAMP,TP00351-51 FF-CABLE, 5P 1.25 150MM FF-CABLE,16P -1.0 FF-CABLE,6P 1.25 JACK,DIA6.3 BLK ST W/SW TC TERMINAL,SP 4P(MSC) JACK,PIN 2P MSP 242V05 PBSN TERMINAL,ANT 4P MSP-154V-02 PROTECTOR,3A 491SERIES 60V PROTECTOR,3A 491SERIES 60V FILTER, EM BL OIRNI COIL,1UH K(MDEC) COIL,1UH K(MDEC) COIL,OSC 85K BIAS COIL,FM DET-N(TOK) FLTR,PCFJZH-450 L(TOK) COIL,2.2UH(CECS) COIL,2.2UH(CECS) COIL,FM-RF-U2 2G COIL,2.2UH(CECS) COIL,FM-OSC-U 2G COIL,FM IFT 7-6.2 (COILS) COIL,AM PACK 4(TOK) PT,ANE-C LH CAP, U 0.01-25 RELAY,OSA-SS-212DM5 SW,SL 1-2-3 SWS2301 TERMINAL, 1P MSC TERMINAL, 1P MSC VIB,XTAL 16.934MHZ VIB,XTAL 4.500MHZ CSA-309
REF. NO. PART NO. C278 C279 C280 C281 C282 C500 C501 C505 C506 C507 C508 C509 C510 C511 C512 C514 C516 C517 C518 C523 C524 C525 C526 C527 C528 C530 C531 C532 C533 C534 C535 C536 C537 C538 C539 C540 C541 C590 CN500 CN501 CNA501 EMI271 FL501 J271 L501 S201 S202 S203 S204 S205 S206 S208 S209 S210 S211 S212 SFR501 VR271 87-012-195-080 87-010-405-040 87-010-759-080 87-012-270-080 87-010-177-080 87-010-759-080 87-010-406-080 87-010-829-080 87-010-263-040 87-010-246-040 87-010-192-080 87-010-404-040 87-010-404-040 87-010-759-080 87-010-263-040 87-012-274-080 87-012-286-080 87-010-759-080 87-012-268-080 87-010-248-040 87-010-192-080 87-010-401-040 87-012-172-080 87-012-274-080 87-010-175-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-199-080 87-010-759-080 87-016-459-040 87-010-384-040 87-009-345-010 87-A60-673-010 8Z-ZM2-601-010 87-008-372-080 8A-NEC-601-010 87-A61-243-010 87-A50-655-010 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-A90-095-080 87-024-431-080 87-NB7-602-010
KANRI DESCRIPTION NO. C-CAP,U 100P-50CH CAP,E 10-50 C-CAP,U, 0.1-25F CAP, U 470P-50 C-CAP,S 820P-50 SL C-CAP,U, 0.1-25F CAP, ELECT 22-50 CAP, U 0.047-16 CAP,E 100-10 CAP,E 47-35 SME C-CAP,S 0.022-50 F CAP,E 4.7-50 SME CAP,E 4.7-50 SME C-CAP,U, 0.1-25F CAP,E 100-10 SME CHIP CAP,U 1000P-50B C-CAP,U 0.01-25 K B C-CAP,U, 0.1-25F CAP,U 330P-50 K B GRM CAP,E 220-10 SME C-CAP,S 0.022-50 F CAP,E 1-50 SME CAPACITOR CHIP U 10P CH CHIP CAP,U 1000P-50B CAP 560P C-CAP,U C-CAP,U C-CAP,U C-CAP,U C-CAP,U 100P-50CH 100P-50CH 100P-50CH 100P-50CH 100P-50CH
!
! !
!
!
C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U 100P-50CH C-CAP,U 100P-50CH CAP 220P C-CAP,U, 0.1-25F CAP,E 470-10 SMG CAP,E 100-25 SME CONN,2P H WHT PH CONN,9P H 2MM JMT CONN ASSY,9P ZZM-2 FILTER, EMI BL OIRNI FL,HNA-10SS15T JACK,6.3 BLK MONO W/SW V MSC COIL,CLK 4.19MHZ (TOKO)7KLY SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M
!
! !
! !
SW,TACT EVQ11G04M SFR,3.3K RH063EC VR,RTRY 10KAX1 1 V
CD MOTOR C.B C201 C202 C203 C271 C272 C273 C274 C275 C276 C277 87-010-401-040 87-010-759-080 87-010-260-040 87-012-282-080 87-010-112-040 87-010-545-040 87-012-195-080 87-010-545-040 87-A10-248-080 87-010-405-040 CAP,E 1-50 SME C-CAP,U, 0.1-25F CAP,E 47-25 M 11L SME CAP, U 4700P-50 CAP,E 100-16 CAP,E 0.22-50 SME C-CAP,U 100P-50CH CAP,E 0.22-50 SME C-CAP,U0.1-16KBR CAP,E 10-50 M2 PIN3 SW1 9X-262-576-910 91-564-722-110 91-572-085-120 MOTOR GEAR ASSY CONNECTOR,6P LEAF SW
8
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Resistor Code Value of resistor Chip resistor
Dimensions (mm)
Figure
Wattage 1/16W 1/16W 1/10W 1/8W
Type 1005 1608 2125 3216
Tolerance 5% 5% 5% 5%
Symbol CJ CJ CJ CJ
Form
L W
L 1.0
t
W 0.5 0.8 1.25 1.6
t 0.35 0.45 0.45 0.55
:A Resistor Code : A
104 108 118 128
1.6 2 3.2
TRANSISTOR ILLUSTRATION
E C B
E C B
B C E
E C B
KTA1266GR KTC3198GR CSA952K
CSC4115BC CD1585BC
2SB1370
2SC5343G
S
C
D G
B E
S D G
2SJ460 2SK2541
2SK360E
2SA1235F 2SC3052F 2SC5345S(0) 2SC2714 CSD1306E
DTA114TK DTA114TKA KRA107S KRA102S KRC104S
9
WIRING 1 (MAIN)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U
10
SCHEMATIC DIAGRAM 1 (MAIN 1/3)
11
SCHEMATIC DIAGRAM 2 (MAIN 2/3: TUNER SECTION)
12
SCHEMATIC DIAGRAM 3 (MAIN 3/3: CD SECTION)
13
SCHEMATIC DIAGRAM 4 (FRONT)
14
WIRING 3 (DECK)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
15
WIRING 4 (CD MOTOR)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A
C CD MOTOR C.B
B
C
D
E
F
TO MAIN C.B CN302
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
16
IC BLOCK DIAGRAM
17
FL (HNA-10SS15T) GRID ASSIGNMENT & ANODE CONNECTION
GRID ASSIGNMENT
ANODE CONNECTION
18
IC DESCRIPTION
IC, M38B57MCH - E249FP Pin No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
Pin Name
NC I-HOLD I-TRAY SW I-D-SW I-KEY2 I-KEY1 O-DSP DATA O-MOTOR I-RMC RESET I-STEREO O-DSC/ O-PLL.DATA VSS XIN XOUT VCC O-PB1 O-POWER O-C.SHIFT O-RMT O-BIAS O-TU ON O-CD ON O-PLL CLK I-TM BASE O-CD CLOSE O-CD OPEN VEE O-STB (DSP) O-K-SCAN O.PLL_CE NC G10 G9 G8 G7 G6 G5 G4 G3 G2
I/O
-- I I I I I -- O I I I O -- I O -- O O O O O O O O I O O -- -- O O -- O O O O O O O O O Not connected. Hold input. CD tray SW AD input.
Description
CD door open/close AD detection input (Not used). Key AD input 2. Key AD input 1. Not used. Cassette deck motor control output. System remote control signal input (Active "L"). Reset input for MICON. Tuner stereo detect input. Function IC control output/PLL data output. Connected to GND. 4.19MHZ oscillator circuit. 4.19MHZ oscillator circuit. Power supply. Cassette deck output switching PB1/PB2. Power control ON/OFF output. Clock shift output for micro computer when tuner receiving broadcast. REC MUTE output. Bias ON/OFF output. Tuner power supply ON/OFF output. CD power supply ON/OFF output. PLL IC clock output. Reference clock input for timer switch. CD tray close data output. (Not used) CD tray open data output. (Not used) Power supply for FL display. Not used. Initial scan output. Tuner PLL IC chip enable output. Not connected. FL grid output (G10). FL grid output (G9). FL grid output (G8). FL grid output (G7). FL grid output (G6). FL grid output (G5). FL grid output (G4). FL grid output (G3). FL grid output (G2).
19
Pin No.
42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Pin Name
G1 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 I-TU3/P3 I-TU2/P2 I-TU1/P1 NC NC I-SUB Q (CD) O-CD.CE I-WRQ (CD) O-CL (CD) O-DATA (CD) I-TUNE/IFC AVSS VREF I-DRF (CD) NC NC NC NC I-TP.SW
I/O
O -- -- O O O O O O O O O O O O O O O O O I/O I/O I/O -- -- I O I O O I -- -- I -- -- -- -- I FL grid output (G1). Not used. Not used. FL segment output (P20). FL segment output (P19). FL segment output (P18). FL segment output (P17). FL segment output (P16). FL segment output (P15). FL segment output (P14). FL segment output (P13). FL segment output (P12). FL segment output (P11). FL segment output (P10). FL segment output (P9). FL segment output (P8). FL segment output (P7). FL segment output (P6). FL segment output (P5). FL segment output (P4).
Description
TU3 diode input/FL segment output (P3). TU2 diode input/FL segment output (P2). TU1 diode input/FL segment output (P1). Not connected. Not connected. SUB-Q data input. CD data chip enable output. CD WRQ input. CD IC control clock output. CD IC control data output. Tuner SD detection input/Tuner IF count input. Connected to GND. Power supply. CD DRF input. Not used. Not used. Not connected. Not used. Deck mechanism SW AD input.
20
IC, LC78641NE-D Pin No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38
Pin Name
PDO1 PDO2 VVSS PCKIST VVDD FR HFL SLCIST SLCO EFMIN JITTV JITTC BH PH (RFENV) FE TE VREF ADAVDD ADAVSS PHREF BHREF TBLO TDO FDO SPDO SLDO FG LASER CONT1 CONT2 CONT3 CONT4 CONT5 PCK C2F VDD DOUT FSX
I/O
O O -- -- -- -- I -- O I O O I I I I I -- -- O O O O O O O I/O O I/O I/O I/O I/O I/O O -- -- O O
Description
Internal VCO control phase comparator output pin. (Pull down) Internal VCO control phase comparator output pin. OFF for rough servo, ON for phase servo. (Pull down) Internal VCO ground pin. PDO output current adjustment resistor connection pin. Internal VCO power supply pin. VCO frequency range adjustment resistor connection pin. (Pull up) Mirror detection signal input pin. SLCO output current adjustment resistor connection pin. Control output. EFM signal input pin. Jitter detection monitor pin. (Not used) Jitter detection monitor pin. (Pull down) BH signal input pin. (Connected to GND) PH signal or RFENV signal input pin. FE signal input pin. TE signal input pin. VREF input pin. Servo A/D, D/A power supply pin. Servo A/D, D/A ground pin. PH reference output pin. (Not used) BH reference output pin. (Not used) Tracking balance output pin. Tracking control output pin. Focus control output pin. Spindle control output pin. Thread control output pin. Output driver VREF output pin. FG signal input pin. (Connected to GND) Laser ON/OFF control pin. General-purpose input/output pin 1. General-purpose input/output pin 2. General-purpose input/output pin 3. General-purpose input/output pin 4. General-purpose input/output pin 5. (Not used) EFM data playback clock monitor pin. Average 4.3218MHz when the phase is locked. (Not used) C2 flag output pin. (Not used) Digital power supply pin. Digital out output pin. (EIAJ format). (Not used) Output pin for the 7.35kHz synchronization signal divided from the crystal oscillator. (Not used)
21
Pin No.
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77
Pin Name
EFLG TEST EMPH MUTEL MUTER LVDD LCHO LVSS RVSS RCHO RVDD XVDD XIN XOUT XVSS ASLRCK ASDACK ASDFIN LRSY DATACK DATA 16M SFSY SBSY PW SBCK CE CL DI DO INT WRQ RES DRF C2F VDD DOUT CONT7 V/P
I/O
O I I/O O -- -- I -- O I O O I O I I I -- -- O O O O O O I I I I O O O I O -- -- I/O I/O O Crystal oscillator ground pin. L/R clock input pin. (Connected to GND) Bit clock input pin. (Connected to GND) Test input pin. (Connected to GND)
Description
C1, C2 error correction monitor pin. (Not used)
Emphasis pin. Which becomes an input pin after reset and can be controlled externally. This becomes an emphasis monitor pin under control by command. (Not used) L channel mute output pin. (Not used) R channel mute output pin. (Not used) L channel power supply pin. L channel output pin. L channel ground pin. R channel ground pin. R channel output pin. R channel power supply pin. Crystal oscillator power supply pin. Connections for a 16.9344MHz crystal oscillator pin.
L/R channel data input pin. (Connected to GND) L/R clock output pin. (Not used) Bit clock output pin. (Not used) L/R channel data output pin. (Not used) 16.9344MHz output pin. (Not used) Subcode frame synchronization signal output pin. This signal falls when the subcode is in the standby state. (Not used) Subcode clock synchronization signal output pin. (Not used) Subcode P, Q, R, S, T, U and W output pin. (Not used) Subcode readout clock input pin. (Connected to GND) Chip enable signal input pin. Data transfer clock input pin. Data input pin. Data output pin. Interruption signal output pin. (Not used) Interruption signal output pin. Reset input pin. This pin must be set low briefly after power is first applied. Focus ON detect pin. Microprocessor interface power supply. Digital ground pin. General-purpose input/output pin 6. (Not used) General-purpose input/output pin 7. (Not used) Rough servo/phase control automatic switching monitor output pin. " H" for rough servo and " L" for phase servo. (Not used)
22
Pin No.
78
Pin Name
FSEQ
I/O
O
Description
Synchronization signal detection output pin. Outputs a high level when the synchronization signal detected from the EFM signal and the internally generated synchronization signal agree. (Not used)
79 80
DEFECT EFMO
I/O O
Defect pin. Which becomes an input pin after reset and can be controlled externally. This becomes the defect monitor pin under control by command. (Not used) EFM signal output pin. (Not used)
23
ADJUSTMENT
< TUNER SECTION >
1. Clock frequency Check Settings : · Test point : TP2 (CLK) Method : Set to AM 1710kHz and check that the test point is 2160kHz ± 45Hz. 2. AM VT Check Settings : · Test point : TP1 (VT) Method : Set to AM 1710kHz, 530kHz and check that the test point is less than 8.5V (1710kHz) and more than 0.6V (530kHz). 3. FM VT Adjustment Settings : · Test point : TP1 (VT) · Adjustment location : L907 Method : Set to FM 108.0MHz and adjust L907 so that the test point is 7.0V ± 100mV. 4. AM Tracking Adjustment Settings : · Test point : TP8 (Lch), TP9 (Rch) · Adjustment location : L951(1/3) ........................................ 999kHz Method : Set to AM 999kHz and adjust L951(1/3) to MAX. 5. FM Tracking Adjustment Settings : · Test point : TP8 (Lch), TP9 (Rch) ·Adjustment location : L904 Method : Set to FM 87.5MHz and adjust L904 so that the test point is maximum. 6. AM IF Adjustment Settings : · Test point : TP8 (Lch), TP9 (Rch) · Adjustment location : L802 ................................................ 450kHz 7. DC Balance / Mono Distortion Adjustment Settings : · Test point : TP3, TP4 (DC Balance) : TP8(Lch), TP9 (Rch) (Distortion) · Adjustment location : L801 · Input level : 60dBµV Method : Set to FM 98MHz and adjust L801 so that the voltage between TP3 and TP4 is 0V ± 0.04V. Then check the distortion is less than 1.3%. 2. Head Azimuth Adjustment (DECK 1, DECK 2) Settings : · Test tape : TTA330 · Test point : TP8 (Lch), TP9 (Rch) · Adjustment location : Head azimuth adjustment screw Method : Play back (FWD) the 8kHz signal of the test tape and adjust screw so that the output becomes maximum. Next, perform on REV PLAY mode. 3. PB Frequency Response Check (DECK 1, DECK 2) Settings : · Test tape : TTA330 · Test point :TP8 (Lch), TP9 (Rch) Method : Play back the 315Hz and 8kHz signals of the test tape and check that the output ratio of the 8kHz signal with respect to that of the 315Hz signal is 0dB ± 4dB. 4. REC/PB Frequency Response Check (DECK 1) Settings : · Test tape : TTA602 · Test point : TP8 (Lch), TP9 (Rch) · Input signal: 1 kHz, 8 kHz (LINE IN) (-20 UV) Method : Apply a 1kHz signal and REC mode. Then adjust OSC attenuator so that the output level at the TP8, TP9 becomes 80mV. Record and play back the 1kHz and 8kHz signal and check that the output of the 8kHz signals is 0dB ± 5dB with respect to that of the 1 kHz signal. 5. REC/PB Sensitivity Check (DECK 1) Settings : · Test tape : TTA602 · Test point : TP8 (Lch), TP9(Rch) · Input signal : 1kHz(LINE IN) (0 UV) Method : Apply a 1kHz signal and REC mode. Then adjust OSC attenuator so that the output level at TP8, TP9 becomes 8mV. Record and play back the 1kHz signals and check that the output is 2dB ± 3.5dB. 6. PB Sensitivity Check (DECK 1, DECK 2) Settings : · Test tape : TTA200 · Test point :TP8 (Lch), TP9 (Rch) Method : Play back the test tape and check that the output level of the test point is 110mV ± 3.5dB.
< DECK SECTION >
1. Tape Speed Adjustment (DECK 1) Settings : · Test tape : TTA100 · Test point : TP8 (Lch), TP9 (Rch) · Adjustment location : SFR501 Method : Play back the test tape and adjust SFR501 so that the frequency counter reads 3000Hz ± 8Hz (FWD) and ± 45Hz (REV) with respect to forward speed.
< FRONT SECTION >
1. µ-CON OSC Adjustment Settings : · Test point : TP7 and (GND) · Adjustment location : L501 Method : Insert AC plug while pressing TUNER function key. Adjust L501 so that the frequency at the test point is 233.4Hz ± 0.23Hz.
24
MECHANICAL EXPLODED VIEW 1 / 1
B
19 18 B
21
29
B B 22 20 25 26 B 28 A I 30 G E E PWB a 23 24 PWB, FFC GUIDE B B C B
C
17
KSM213CDM 35 34 H 34
16
14 C 9 10 FL
27 B B D B
8 H PWB
b B B 11 PWB GUIDE, H-WIRE 6 4 B b 5 32 13 3 1 B C a 31 12 B B F B ZZM-2 B HT-SINK, TR LOW F B 15
B
2
3
7 33
25
MECHANICAL PARTS LIST 1 / 1
REF. NO. PART NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 8A-NED-005-010 8A-NED-006-010 82-NF7-218-010 8A-NED-002-010 8A-NED-003-010 8A-NED-034-010 86-NFZ-231-010 8A-NED-001-110 8A-NED-007-010 8A-NED-009-010 8A-NED-008-010 8A-NED-010-110 8A-NED-011-010 8A-NFA-208-010 8A-NEC-206-010 87-NF8-220-010 88-CH6-019-110 8A-NED-012-210 8A-NED-203-110 87-036-389-010 8A-NED-033-110 84-CT5-209-010 87-036-368-010 88-CD9-210-210 88-CD9-211-210
KANRI DESCRIPTION NO. WINDOW,CASS 1 WINDOW,CASS 2 SPR-T,CASS BOX,CASS 1 BOX,CASS 2
WINDOW,DISPLAY CCE DMPR,70 CABI,FR KEY,POWER KEY,PLAY KEY,UP/DOWN KEY,CASS 1 KEY,CASS 2 GUIDE,FL 100-25 ANFA HLDR,DECK DMPR,150 PANEL,CD PANEL,TOP SPR,LID SW,PUSH LOCK LID,ASSY CD PLATE,MAGNET MAGNET BASE,CHUCK RING,CHUCK
REF. NO. PART NO.
26 27 28 29 30
!
8A-NED-201-010 8A-NED-202-010 8A-NEC-013-010 8A-NED-025-010 8A-NEC-201-110 8A-NEC-014-010 87-A80-157-010 8A-NEC-205-010 87-253-033-110 87-067-703-010 87-067-641-010 87-571-092-410 87-078-191-010 87-067-001-010 87-NF4-224-010 8A-NED-204-010 87-067-579-010
88-CH6-220-110 8A-NED-209-010
KANRI DESCRIPTION NO. HLDR,TOP L HLDR,TOP R PANEL,LEFT CABI,REAR LHSC1NC1 HLDR,PT
PANEL,RIGHT AC CORD ASSY,E BLK CC CABI,BOTTOM SCREW,U+2-4 TAPPING SCREW, BVT2+3-10 UTT2+3-8(W/O SLOT)BL TAPPING SCREW, VIT+3-4 S-SCREW,IT+4-10 S-SCREW,BVWWST2+3-12 W/O SLOT S-SCREW,IT3B+3-8 CU S-SCREW,MECH M3 TAPPING SCREW, BVT2+3-8
CUSH,CD A CUSH,W5-8-1.5
31 32 33 A B C D E F G H I
34 35
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green YM Metallic Yellow DM Metallic Orange PT Transparent Pink LA Aqua Blue GL Light Green
26
TAPE MECHANISM EXPLODED VIEW 1 / 1
54 4 14 15 3 6 2 1 59 16 61 17 B 46 45 37 44 43 b 1 12 11 51 a 12 4 3 9 39 8 7 57 58 2 1 10 9 8 7 57 58 42 48 56 44 49 43 41 40 60 39 38 50 46 45 11 40 53 52 10 51 47 1 36 37 35 33 34 32 34 53 47 16 38 33 24 26 27 29 25 18 59 30 5 17 18 25 24 29 13 19 27 14 15 13 26 19 28 5 b 6 55 a 31 54 28 55 21 20 21 20 23 23 22 TERMINAL,LB1 A 22
TERMINAL,LB1 A
27
TAPE MECHANISM PARTS LIST 1 / 1
REF. NO. PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 8Z-ZM1-254-310 8Z-ZM1-225-110 8Z-ZM1-253-210 8Z-ZM1-217-110 8Z-ZM1-212-210 8Z-ZM1-245-310 8Z-ZM1-236-010 8Z-ZM1-252-110 8Z-ZM2-213-010 8Z-ZM1-269-010 8Z-ZM1-238-110 8Z-ZM1-237-110 8Z-ZM1-209-510 8Z-ZM1-218-210 8Z-ZM1-256-010 8Z-ZM1-244-110 8Z-ZM1-247-310 8Z-ZM1-261-110 8Z-ZM1-221-210 8Z-ZM1-205-310 8Z-ZM1-248-210 87-A90-403-110 84-ZM2-227-310 8Z-ZM1-216-110 8Z-ZM1-246-110 8Z-ZM2-214-110 8Z-ZM2-212-010 8Z-ZM1-207-010 8Z-ZM1-206-010 8Z-ZM1-210-010 87-A90-404-010 8Z-ZM2-218-010 87-A91-492-010 8Z-ZM1-226-010 8Z-ZM1-241-210
KANRI DESCRIPTION NO. SPR-C,REEL R GEAR,REEL R SPR-C,AUTO SENSOR LEVER,AUTO SENSOR LEVER,T-UP SPR-T,AUTO CLR,SLIP FF/REW SPR-C,FF/REW GEAR,SLIP FR A ZZM-2 FELT,FF/REW 2 GEAR,SLIP FF/REW B 2 LEVER,FF/REW 2 LEVER,PAUSE LEVER,E-LOCK H SPR-P,PAUSE SPR-T,T-UP SPR-T,PINCH ROLLER ASSY,PINCH LEVER,PINCH LEVER,PLAY SPR-T,BRG HEAD,RPH MS15R SPR-C,AZIMUTH LEVER,AUTO SPR-T,AUTO 2 GEAR,IDL REW ZZM-2 LEVER,STOP ZZM-2 LEVER,FF LEVER,REW LEVER,REC HEAD,EH LE15B LEVER,REC LOCK ZZM-2 SW,LEAF MSW18560 GEAR,REEL L SPR-T,PLAY
REF. NO. PART NO. 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 A B 8Z-ZM1-220-110 8Z-ZM1-249-210 8Z-ZM1-242-310 8Z-ZM3-244-110 8Z-ZM1-232-010 8Z-ZM1-290-010 8Z-ZM2-601-010 8Z-ZM1-228-010 8Z-ZM1-265-010 8Z-ZM1-227-010 8Z-ZM1-251-210 8Z-ZM1-243-310 87-A91-532-010 8Z-ZM1-235-010 8Z-ZM2-216-010 8Z-ZM1-260-010 8Z-ZM2-201-510 8Z-ZM1-255-310 8Z-ZM2-219-010 8Z-ZM1-214-310 8Z-ZM2-230-010 8Z-ZM1-257-110 8Z-ZM1-275-010 87-B10-301-010 87-A91-494-010 8Z-ZM1-241-010 84-ZM2-242-010 8Z-ZM2-220-110
KANRI DESCRIPTION NO. LEVER,REC SENSOR SPR-T,FR SPR-T,FF/REW GEAR,CAM TD20 GEAR,IDL FF/REW FLY-WHL ASSY,ZZM-1 CONN ASSY,9P ZZM-2 GEAR,SLIP T-UP B FELT,T-UP GEAR,SLIP T-UP A SPR-C,T-UP SLIP SPR-T,STOP/PAUSE MOT,MS15U2LW1A PULLEY,MOT BELT,MAIN M SPR-P,CASETTE CHAS ASSY,ZZM-2 SPR-T,E-LOCK LEVER,E-OPEN ZZM-2 LEVER,LOCK FLY-WHL ASSY,ZZM-2 SPR-C,F/R W-L,1.47-4-0.25 W-L,1.63-3.2-0.5 SLIT SW,LEAF MSW17820 SPR-T,PLAY S-SCREW,AZ1-2-6.4 V+2.6 ZZM-2
28
CD MECHANISM EXPLODED VIEW 1 / 1
2
COVER
5
3
A
SPINDLE MOTOR (M1)
1
4 (M2) SLED MOTOR
P.W.B
CD MECHANISM PARTS LIST 1 / 1
REF. NO. PART NO. 1 2 3 4 5 A 9X-262-620-210 92-626-907-010 87-A90-468-010 92-626-908-010 92-627-003-020 97-621-255-150
KANRI DESCRIPTION NO. MOTOR CHASSIS ASSY GEAR(A) PICK UP KSS-213C SHAFT SLED GEAR(B)(RP) SCREW+P2-3
29
SPEAKER DISASSEMBLY INSTRUCTIONS
Type.1 Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units. Type.4
TOOLS
1 Plastic head hammer 2 (() flat head screwdriver 3 Cut chisel
1
2
3
How to Remove the PANEL, FR
Type.2
Remove the grill frame and four pieces of rubber caps by pulling out with a flat-bladed screwdriver. Remove the screws from hole where installed rubber caps. Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker units. 1. Insert the (() flat head screwdriver tip into the gap between the PANEL, FR and the PANEL, SPKR. Tap the head of the (() flat head screwdriver with the plastic hammer head, and create the clearance as shown in Fig-1. Insert the cut chisel in the clearance, and tap the head of the cut chisel with plastic hammer as shown in Fig-2, to remove the PANEL, FR. Place the speaker horizontally. Tap head of the cut chisel with plastic hammer as shown in Fig-3, and remove the PANEL, FR completely.
2.
3.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into one of the hollows around speaker unit, and then remove the speaker unit. After replacing the speaker unit, install it turning to clockwise direction until "click" sound comes out.
Fig-1
Fig-2
Fig-3
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four corners of the PANEL, FR with the plastic hammer to fit the PANEL, FR into the PANEL, SPKR completely.
30
SPEAKER PARTS LIST (SX-NSZ1)
REF. NO. PART NO.
KANRI DESCRIPTION NO. 1 8A-NSN-001-010 PANEL, FR 2 8A-NSN-002-010 GRILLE, FRAME ASSY 3 8A-NSN-008-010 CORD, SPKR 4 8A-NSM-602-010 SPKR, 100
!
31
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9820572 0251431 Printed in Singapore