Text preview for : DT1350-PSM.pdf part of Disney DT1350-PSM Service Manual - 13'' color television
Back to : 1350.zip | Home
DT1350-P
SERVICE MANUAL
COLOR TELEVISION RECEIVER
ORIGINAL MFR'S VERSION A
Design and specifications are subject to change without notice.
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual.
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an electric shock while the electric current is flowing.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used.
7. PERFORM A SAFETY CHECK AFTER SERVICING
Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE
In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal Earphone jack
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL.
IMPORTANT
Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.
A1-1
CONTENTS
SERVICING NOTICES ON CHECKING .......................................................................................................... A1-1 HOW TO ORDER PARTS ............................................................................................................................... A1-1 IMPORTANT .................................................................................................................................................... A1-1 CONTENTS ..................................................................................................................................................... A2-1 GENERAL SPECIFICATIONS ........................................................................................................................ A3-1~A3-4 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ................................................................................................................. B1-1 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................................... B2-1, B2-2 SERVICE MODE LIST ..................................................................................................................................... C-1 CONFIRMATION OF HOURS USED .............................................................................................................. C-1 WHEN REPLACING EEPROM (MEMORY) IC ............................................................................................... C-1 ELECTRICAL ADJUSTMENTS ....................................................................................................................... D-1~D-5 BLOCK DIAGRAM ........................................................................................................................................... E-1, E-2 PRINTED CIRCUIT BOARDS MAIN/CRT/OPERATION/JACK1/JACK2 ..................................................................................................... F-1~F-4 SCHEMATIC DIAGRAMS MICON/TUNER ............................................................................................................................................ G-1, G-2 CHROMA ..................................................................................................................................................... G-3, G-4 TV POWER .................................................................................................................................................. G-5, G-6 DEFLECTION/CRT ...................................................................................................................................... G-7, G-8 SOUND/AV .................................................................................................................................................. G-9, G-10 WAVEFORMS .................................................................................................................................................. H-1, H-2 MECHANICAL EXPLODED VIEW ................................................................................................................... I-1 MECHANICAL REPLACEMENT PARTS LIST ............................................................................................... J1-1 ELECTRICAL REPLACEMENT PARTS LIST ................................................................................................. J2-1, J2-2
A2-1
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH 13 inch / 335.4mmV Normal 90 degree +0.45G/0.18G NTSC 2Speaker Ext 3 Inch 8 ohm 0.5+0.5 W -W No US System M 1Tuner USA(W/ CATV) F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz at AC 54 W at AC 120 V 60 Hz 5 W at AC 120 V 60 Hz -kWh/Year Yes Yes No UL / CSA FCC / IC DHHS / HWC +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH Yes Disney Charecter Yes Yes Yes Yes Yes Yes Yes No No No No No No Yes Yes Yes Yes Yes Yes No No No Yes Yes Yes Yes Yes Yes Yes Yes No No No No No
Color System Speaker Position Size Impedance MAX 10%(Typical)
Sound Output NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH
G-2
T u n in g System
System Destination Tuning System Input Impedance CH Coverage Picture(FP) Sound(FS) FP-FS
Intermediate Frequency
G-3
Power
Preset CH StereoTV Sound (Ext Audio Input Only) Tuner Sound Muting Power Source AC DC Power Consumption Stand by (at AC) Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Safety Radiation X-Radiation Operation Storage
Protector
G-4
Regulation
G-5 G-6 G-7
Temperature Operating Humidity On Screen Menu Display
Menu Type Picture Contrast Brightness Color Tint Sharpness Reset Audio Bass Treble Balance BBE On/Off Stable Sound On/Off CH Set Up TV/CATV Auto CH Memory Add/ Delete Language V-chip CH Label Favorite CH Color Stream DVD/DTV CAPTION Control Level Sound Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light
-
A3-1
GENERAL SPECIFICATIONS
Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Sleep Timer Sound Mute V-chip Rating G-8 G-9 OSD Language Clock and Timer Sleep Timer Max Time Step Program(On Timer / Off Timer) No Yes No Yes No Yes Yes Yes English
French
Spanish
G-10
Remote Control
G-11
Features
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode) more than Unit Glow in Dark Remocon Format Custom Code Power Source Voltage(D.C) UM size x pcs Total Keys Keys Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu Enter Mute Exit MTS(Audio Select) Set + Set Multi Brand Keys CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) Code FF Rew Rec Play Stop TV VCR Cable Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search
120 Min 10 Min No No -Min Sec RC-JK No NEC 86-05 h 3V UM-4 x 2 pcs 23 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes No Yes No No No No No No No No No No No No No No No No No Yes Yes No Yes No No Yes Yes Yes USA,ORION Type No No
A3-2
GENERAL SPECIFICATIONS
CH Allocation StereoTV Sound (Ext Audio Input Only) Channel Lock Just Clock Function Game Position CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound Energy Star Power On Memory Favorite CH Owner's Manual No Yes No No No No No No No No Lines Yes No Yes No No Yes Language w/Guarantee Card Buyer Model No. No English Spanish French No DT1350-P Yes No
G-12
Accessories
Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safeguard Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter Safety Strap Printed Matter for Disney Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down MENU TV/Video Rear AC/DC TV/CATV Selector Degauss Main Power SW Indicator Power Stand-by On Timer Terminals Front Video Input Audio Input Other Terminal Rear Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output Euro Scart Color Stream Diversity
No No No Yes No No No No No No No No No No No No No No No Yes Yes Yes No No No Yes Yes Yes Yes Yes Yes No No No No No No No RCA x 1 RCA x 2 Head Phone RCA x 1 No RCA x 2 No No No No No No
G-13
Interface
A3-3
GENERAL SPECIFICATIONS
Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm)
w/o Speaker,Legs Approx. W x D x H (mm)
Yes No F Type 401.5 401.5 11.0kg 9.5 kg 13.5kg -----No x 371 x 465.5 x 371 x 350 ( 24.3lbs) ( 20.9lbs ) ( 29.8lbs) No Sets /-x -- x -No
G-14 G-15
Set
Size
Weight
Net (Approx.) Net w/o Speaker,Legs Approx. Gross (Approx.) Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand Pb Free Lead-free Solder Other Cd Free
G-16
Carton
G-17
Cabinet Material
G-18
Environment
Yes Double / Full Color 493 x 423 x 465 As per Buyer's Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 62 640 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No No No No No
A3-4
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
* *
After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged.
REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated screwdriver, touch the support of the Anode with the tip of the screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap
Fig. 1-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
Support Alligator Clip
CRT
GND on the CRT Fig. 1-1 2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap Fig. 1-4 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
CRT CRT Support Fig. 1-2
Support Fig. 1-5
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
B1-1
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
Masking Tape (Cotton Tape)
IC
Tweezers
Fig. 2-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) NOTE Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely. 4. Peel off the Masking Tape.
Fig. 2-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Blower type IC desoldering machine
Braided Shield Wire
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
B2-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 2-8.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
Soldering Iron
IC
Supply soldering from upper position to lower position
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Braided Shield Wire
Fig. 2-7
B2-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key VOL. (-) MIN VOL. (-) MIN Remocon Key 0 1 Operations Releasing of V-CHIP PASSWORD and LOCK PASSWORD. Initialization of the factory. NOTE: Do not use this for the normal servicing. If you set a factory initialization, the memories are reset such as the clock setting, the channel setting, the POWER ON total hours, and PLAY/REC total hours. POWER ON total hours is displayed on the screen. Refer to the "CONFIRMATION OF HOURS USED". 6 Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC". VOL. (-) MIN 9 Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
VOL. (-) MIN
CONFIRMATION OF HOURS USED
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". 1. Set the VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. 3. After the confirmation of using hours, turn off the power.
ADDRESS DATA
INIT
00
00
Initial setting content of MEMORY IC. POWER ON total hours.
= (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
CRT ON 0010
FIG. 1
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. INI 00 10 +0 00 02 Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. While holding down VOLUME button on front cabinet, press key 6 on remote control for more than 1 second. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. +/- button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. While holding down VOLUME button on front cabinet, press key 1 on remote control for more than 1 second. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. +1 60 +2 99 +3 93 +4 1B +5 B3 +6 24 +7 3B +8 09 +9 0F +A 07 +B 05 +C 00 +D AB +E 00 +F 08
C-1
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL ADJUSTMENTS
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION · Use an isolation transformer when performing any service on this chassis. · Before removing the anode cap, discharge electricity because it contains high voltage. · When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. · When you exchange IC and Transistor for a heat sink, apply the silicon grease (YG6260M) on the contract section of the heat sink, Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.) Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1.
2. BASIC ADJUSTMENTS
2-1: VIF VCO 1. Place the set with Aging Test for more than 10 minutes. 2. Receive an 80dB monoscope pattern. 3. Connect the digital voltmeter between the pin 5 of CP601 and the GND. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "V. VCO". 5. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.5V. 2-2: RF AGC DELAY Place the set with Aging Test for more than 15 minutes. Receive an 63dB monoscope pattern. Connect the digital voltmeter to TP001. Activate the adjustment mode display of Fig. 1-1 and press the channel button (02) on the remote control to select "RF AGC". 5. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.50V±0.05V. 1. 2. 3. 4. 2-3: CUT OFF 1. Adjust the unit to the following settings. R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64, B.BIAS=64, BRI CENT=115, CONT MAX=45. 2. Place the set with Aging Test for more than 15 minutes. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 4. Adjust the Screen Volume until a dim raster is obtained. 2-4: FOCUS
TV
1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-5: WHITE BALANCE
00 OSD H
31 Fig. 1-1
NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 15 minutes. 2. Receive the white 100% signal from the Pattern Generator. 3. Using the adjustment control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (10) on the remote control to select "R. BIAS". 5. Press the CH. UP/DOWN button on the remote control to select the "R. BIAS", "G. BIAS", "B. BIAS", R. DRIVE or "B. DRIVE". 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R. BIAS, G. BIAS, B. BIAS, R. DRIVE, and B. DRIVE at each step tone sections equally. 7. Perform the above adjustments 6 and 7 until the white color is looked like a white.
2. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 3. Press the MENU button on the remote control to end the adjustments.
NO. 00 02 03 04 05 06 07 08 09 10 11 12 13 14 15 FUNCTION OSD H RF.AGC V.VCO H.VCO H.PHAS V.SIZE V.SHIFT R.DRIVE B.DRIVE R.BIAS G.BIAS B.BIAS BRIGHT CENT BRIGHT MAX BRIGHT MIN NO. 16 17 18 19 20 21 22 23 24 28 FUNCTION CONTRAST CENT CONTRAST MAX CONTRAST MIN COLOR CENT COLOR MAX COLOR MIN TINT SHARPNESS FM LEVEL TEST MONO
Fig. 1-2 D-1
ELECTRICAL ADJUSTMENTS
2-6: SUB TINT/SUB COLOR 1. Receive the color bar pattern. (RF Input) 2. Connect the oscilloscope to pin 6 of CP601. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "TINT". 4. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes as straight line. (Refer to Fig. 2-1) 5. Connect the oscilloscope to pin 7 of CP601. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (19) on the remote control to select "COL.CENT". 7. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales 8. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 100% ± 10% of the white level. (Refer to Fig. 2-2) 9. Receive the color bar pattern. (Audio Video Input) 10.Connect the oscilloscope to pin 6 of CP601. 11.Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "TINT". 12.Press the VOL. UP/DOWN button on the remote control until the section "A" becomes as straight line. (Refer to Fig. 2-3) 13.Connect the oscilloscope to pin 7 of CP601. 14.Activate the adjustment mode display of Fig. 1-1 and press the channel button (19) on the remote control to select "COL.CENT". 15.Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales 16.Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 100% ± 10% of the white level. (Refer to Fig. 2-4)
"A"
Fig. 2-3
White 100%
Red 100%
Fig. 2-4
2-7: HORIZONTAL PHASE 1. Receive the monoscope pattern. 2. Using the adjustment control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (05) on the remote control to select "H.PHAS". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2-8: VERTICAL SHIFT 1. Receive the monoscope pattern. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V.SFT". 3. Press the VOL. UP/DOWN button on the remote control until the horizontal line becomes fit to the notch of the shadow mask.
"A"
Fig. 2-1
2-9: VERTICAL SIZE 1. Receive the monoscope pattern. 2. Using the adjustment control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select "V.SIZE". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 10 ± 2%. 5. Receive a broadcast and check if the picture is normal.
White 100%
Red 100%
Fig. 2-2 D-2
ELECTRICAL ADJUSTMENTS
2-10: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum and up 2 steps. (Refer to Fig. 2-5)
TV
00 OSD H A 2-11: SUB BRIGHTNESS
31 B
Fig. 2-5
1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (13) on the remote control to select "BRI.CENT". 2. Press the VOL. UP/DOWN button on the remote control until the white 10% is starting to be visible. 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/AV button on the remote to set to the AV mode. Then perform the above adjustment 1~3. 2-12: SUB CONTRAST 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "CONT MAX". 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "45". 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 2-13: Confirmation of Fixed Value (step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 04 14 15 16 18 20 21 23 24 28 FUNCTION H VCO BRIGHT MAX BRIGHT MIN CONT CENT CONT MIN COLOR MAX COLOR MIN SHARPNESS FM LEVEL TEST MONO RF 03 140 50 30 10 70 00 48 107 00 AV 03 140 50 30 10 70 00 48 107 00
D-3
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue colors. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB R G B
R G B RIGHT/LEFT SLANT
UPWARD/DOWNWARD SLANT Fig. 3-2-a
WEDGE
WEDGE
WEDGE WEDGE POSITION Fig. 3-2-b
PURITY MAGNETS 6 POLE MAGNETS 4 POLE MAGNETS Fig. 3-1
D-4
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CP803B CP806
J801 CD803
CP802B
CRT PCB
CP601
J704
CP803A
FB401
TU001
TP001
CP802A
CP502
L503
CD802
S501A CP101
AC IN
CRT DY CP101
CD2001
CP401 DEGAUSS COIL
S501B J1001 J701 J702 J703
FRONT JACK PCB
J1151 S1152 S1153
FRONT JACK PCB
J1150 S1150 S1151
MAIN PCB OPERATION PCB
D-5
BLOCK DIAGRAM
VIDEO SW IC IC703 MM1501XNRE TUNER/AV1/AV2 Lch SW IC IC701 NJM2534V TUNER/AV1/AV2 Rch SW IC IC702 NJM2534V
J701 2
J703 2 3
J702 2
J704 2 3 4 4
4
4
1
2
2
4
5
7
1
3
2
4
5
7
1
3
7
MEMORY IC IC199 S-24C02BFJ-TB
SDA 5 SCL 6
CHROMA IC IC601 M6125BFP
TU001 5 4 11 1
SOUND AMP IC(Rch) IC IC1001 AN7513 2 6 8
6 2 3 J1001
51 AUDIO OUT 38 EXT C IN 59 RF AGC OUT 63 VIF IN(1) 64 VIF IN(2)
4
4 5
1
SAW FILTER IC MICON IC IC101 OEC7108A SDA1 37 CF601
SOUND AMP IC(Lch) IC IC1002 AN7513
SP1001
2 26
SDA
6 8
SP1002
4
Q606 HI VCC 44 8.7V REG OUT 47
AT5.7V REG OUT 32
46 VOLUME 44 AV2 43 AV1
SCL1 39
27 SCL 19 INV FBP OUT 20 V PULSE OUT 23 R IN 22 G IN 21 B IN 24 FAST BLK
28 POWER ON CONT 30 MCU RESET R OUT 14 G OUT 15 B OUT 16 H OUT 11 FBP IN 10 REG Q603 AT+5V X' TAL 34
H. SYNC 1 V. SYNC 2
RED R 52 GREEN G 51 BLUE B 50 BLANK 49 POWER 33 RESET 30 CVIN 22
REG
Q601 REG
SW+8V
CH DOWN MENU VOL DOWN POWER CH UP
X602 3.579545MHz
Q801
RED OUT
Q802
31 Y SW OUT 5
V OUT 1 OS101
8 KEY1 9 KEY2
GREEN OUT
Q803
REMOCON 15
6
V RAMP FEEDBACK
BLUE OUT
VOL UP P.FAIL 4 LINE
PUMP UP TH501 Q402 3 B Heater 4 F 8 9 G 7 R
L503 DEGAUSS COIL
1 D501~D504 RECTIFIER Q507 IC501 PS2561AL1-1-V(W) FEED BACK T501 7 3 VCC 2
AMP + 6 5
V-OUT IC IC401 LA78040N-E
H. DRIVE Q401 H. OUTPUT
CRT V801
F501
AC IN FEED BACK SW.
DY
FB401
Q501 FET
8
6
16
13
1 3 9 2 FBT
10 F S HV
Q502 BUFFER
E-1
E-2
7
R80
R80
5
3
L801 CP803B CP806 CD803B C819 W006 J701 IC1001 W011 R1002 W016 C1007 C1014 R1008 W908 IC1002 CP1001 C1013 W909 R1009 W017 J702 C1003 J703 J1001
S1151 R804 R802 TP024 Q802 Q801 Q803 W808 W005 R1003 S1150 R811
01
J1150
R809
J8
W015 C1005
TP022
R80
TP023
W012
R500
R814 R806
W010
_A_V
W013 D522 D514 W832 D511 W802 S501B F501 FH501 W014 W003 W007 D515 D518 R513 D528 R107 R108 D517 C122 W811 R512 W815 R111 R518 W040 D103 W031 W029 W027 W028 X101 L101 R110 CP501 C519 C505 W025 W026 FH502 W814 R504 R507 R519 Q507 W008 W009 IC101 W803 W018 CD501
S501A
CP802B SW2001 C715 CC001 CD802B
W001
CP101 C710 L701
C2001 C714 L702 W020 W035 OS2001
PRINTED CIRCUIT BOARDS MAIN/CRT/OPERATION/JACK1/JACK2 (INSERTED PARTS)
R629 W019 W023 R604 C115 W039 W021 R623 Q610 R2008 R2009 Q603 R613 Q606 R632 D104 R447 W042 W041 W037 R401 R409 R517 D412 L501 W038 W030 W046 W043 C118 R408
R620
SW2007 C647 C624 D602 C645 C635 C516 D406 CP502 D502 D503 ICP501 R515 W045 R511 D504 IC501 C502 D501 C503 C518 W022 R648 R635 X602 C625 W054 C638 W034 W033 W036 R505 W044 D505 C515 D601 W024 W049 CD2001
R608
Q601
W032
C716_1
TH501
R528
CF603
SOLDER SIDE
C619_1 W051 W082 D512 C501 R520 R509 C511 W057 R501 R616_1
W081
D516
C627
C517_1
D513
C629_1
W053 D510
4A125V0R250V
W898
SW2006 C634 CP802A C637 D508 W056 C628 C613 W047 R624 R445_1 D605 R001 T502 R002 W072 C446 Q402 C612 W065 C440 W817 W063 R448 W804 W055 W052 D506 C632 L607 CD802A C521_1 C509 C603
CF604
R510
SW2004 CF601
W050
C604
B504
W048
C526
C630 C605 C601 W820 Q605
R516
W819 HS501 C514 R506 Q502
R606
Q604
W062 W059
H
T401 W064 R427 D403 IC401 C414 R424 C417 W074 R418 C437 W070 W069 R422 R446
S4
01
R449
D409
TP001
CF602
L601
R641
HS402
SW2003 L001
W067 R423 R413
Q401 FB401 W068 C506
W060 D001 SW2002
TEDB42A
W066 C427 W075 C422 CP401 SW2005 C403 TU001 R416 C002 C003 R145 R144 W077 R410 R415 C418
W071
W079
C443_1
D405
W080
W810 D410 R421
C434 CD803A CP803A
C448
S1153
C435
J1151
D408 S1152 CP601 J704 D411 W078
R42
9_1
TEDB44A
D404
R403 C406
W809
W821
W073
R542
TMD600A
Q501
R626
W058
D509
F-1
F-2
R5 14
CP 801
TCD456A
R 50 8
TEDB43A
SOLDER SIDE
C655 C623
R622 R615 C626 C606 C618 R609 C602 R628 C631
R2005 R2004 R2003 R420
PRINTED CIRCUIT BOARDS MAIN/CRT/OPERATION/JACK1/JACK2 (CHIP MOUNTED PARTS)
TEDB42A
C004
C001
R003 R005 C008 R004 C1151
TEDB44A
R706 R707
R709
IC
60
1
TEDB43A
F-3
TCD456A
R701 R703 R1001 R702 C1002_1 C1001_1 C1150 R1010 R1005 R815 C809 R123 R102 R131 R139 R151 C140 R133 R140 R147 R148 R116 R132 R105 R106 R150 R149 C136 C139 C141 R125 R135 C513 R122 R103 R121 R120 R104 R152 R124 R118 R153 C706 C101 C708 IC199 C709 C705 R816 C810 R813 C808 C1008 R1004 R1011 C1004 R1006 R705 R704 R711 C713 IC703 C711 C616 R638 R2001 R2002 R2006 R2007 R639 49 17 R612 C622_1 C639 33 R633 R646 C640 Q609 Q611 R642 1 R625 R627 R601 R602 R614 R619 R631 R605 R630 R617 C607 C621 R708 IC701 IC702 C707 C712 C113 R127 C114 C119 R136 R138 C120 C138 R134 R129 C124 C103 R130 C121 C102 R417 R419
B_SHORT
TDM600A
F-4
A
B
C
D
E
F
G
H
2.2K R2002
ACCESSORY 3 ADRES 1 AGC 5 SDA 4 SCL 6 V.S CP101 A2001WV2-5P TM101
12
R2001
8
15
TU001
TECC1040PG38W 7 BPL 9 BTL
13
(MAIN PCB)
CD2001 CU251801 1 2 3 4 5 AT+5V REMOCON KEY2 KEY1 GND 2 AT+5V REMOCON KEY2 C003 50V 4.7 KA R004 100K KEY1 GND 1 2 3 4 5 RC-JK020
2.2K
MICON/TUNER SCHEMATIC DIAGRAM
11 IF 10 8
R2006 R2003
560 SW2001 EVQ21505R VOL DOWN POWER R2004 1K SW2002 EVQ21505R MENU R2005 1.8K SW2004 EVQ21505R VOL UP SW2005 EVQ21505R CH UP SW2003 EVQ21505R CH DOWN 560
R2007 1K R2008 R2009 47 1/4W SW2007 EVQ21505R 47K 1/4W
C2001 25V 10 KA
8
SW2006 EVQ21505R LINE
1 Vout 2 B+ 3 GND
0
14
0
NC 4.9
4.8
4.8
1.3 NC 6.2 NC 4.6
NC 30.0
0
NC
OS2001 PIC-37143TH5
6.3V 470 YK
0.022 F
MTZJ33B
NC
TP001
0.1 F
OPE TEDB42
C004
D001
C001
7
C002
FROM/TO CHROMA GND
7
68P CH R005 270 270
L001 47uH 0305
TUNER+5V AGC
C008
IF
R003
FROM TV POWER R002 12K 1/2W R001 +B 12K 1/2W POWER_FAIL FROM/TO DEFLECTION/CRT +B R124 R104 R103 R102 X-RAY 680 IC MICON IC IC101 C136 R123 4.7K R122 4.7K R121 4.7K R120 4.7K OEC7108A H.SYNC V.SYNC NC P.FAIL SYNC NC AFT KEY1 KEY2 X-RAY NC NC NC NC REMOCON NC NC NC HLF 4.8 4.8 4.7 4.9 0 0 0 1/4W 4.0 1 4.8 51 GREEN G BLUE B BLANK DEGAUSS STANDBY_H 2 0 50 3 3 HD 4 VD R131 4.7K FROM CHROMA 4.7K
SCL_TP SDA_TP
680
680
6
OSD_R
6
0.1 F C139 OSD_G 0.1 F C141 OSD_B 0.1 F OSD_BLK R152
52
RED R
4.9 49 4 2.1 48 5
R139 C140 SYNC 100 R133 4.7K AFT
47
47K VOLUME R153 R145 47K AV2 AV1 POWER R116 47K R132 47K FROM/TO CHROMA R107 SCL 100 1/4W R150 4.7K R108 SDA 100 1/4W R105 4.7K R106 R149 4.7K 4.7K 35 R125 R110 36 37 38 0 NC 4.8 0 4.9 0 5.0 0 NC 0 R111 47K 1/4W D103 MTZJ5.6B C101 0.001 B KA C113 L101 3.9uH R127 12P CH C114 MEMORY IC IC199 S-24C02BFJ-TB 8 VCC 12P CH 2.7K 0 4.9 4.9 2.7 2.7 4.9 40 46 VOLUME NC AV2 AV1 EXT MUTE AUDIO MUTE NC R144 100 1/4W
7
6
5
TO SOUND/AV
47K R118
0 2.8 2.1
0.001
CH
5
R151 4.7K
45
100
8 4.9 9 5.0 10 R140 4.7K R147 4.7K R148 4.7K 11 0 0 0 0
0 0 0 2.4 0
4
42
43
44
4
41
39
SCL1 NC SDA1 NC I2C_OFF X-RAY_TEST POWER PROTECT_H H_CTL RESET OSC2 OSC1 VCC
14 15
13
12
NC
4.5 0 0 0 2.0 R130 0 0.3 2.5 560P B C138 0 C102 2.1 2.0 0 27P CH X101 100CT8R005 8MHz C103 27P CH C120 0.001 CH R134 R129 470 1M C124 Y_VIDEO 0.01 B R138 4.7K R135 4.7K R136 4.7K W814
3
I2C_OFF 1K 1/4W AT+5V POWER PROTECT_H H_CTL RESET
18
47K
17
16
3
C121 1K 220P CH C122 50V 1 KA
34
33
NC V.HOLD CVIN CNVSS Xin Xout VSS
32
31
30
2
C115
29
24
23
22
21
20
19
2
50V 0.1
5 SDA
6 SCL
7 MODE
1
27
28
MTZJ5.6B
330 YK
VSS
D104
4 0 0
3 0
2 0
1
C118
0.1 F
E2
E1
E0
C119
26
25
4.8
4.8
0
4.9
6.3V
PCB010 TMD600
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION
:LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
R.SIGNAL G.SIGNAL B.SIGNAL DEFLECTION SIGNAL TUNER VIDEO SIGNAL
H
1
A
B
C
D
E
F
G
G-1
G-2
A
B
C
D
E
F
G
H
CHROMA SCHEMATIC DIAGRAM
8
FROM TV POWER UNREG+12V 6 REG Q603 KTC3203_Y 8.8 REG Q605 KTC3203_Y 7.2 4.7 REG Q606 KTC3203_Y 11.3 8.5 16V 47 YK D602 KA 7.9 50V 1 KA C622_1 MTZJ8.2B C625 B REG Q601 KTC3203_Y 11.3 8.5 7.9 R632 4.9 5.5 100 1/4W R623 120 1/4W FROM SOUND/AV VIDEO_IN 16V 47 YK SW Q611 DTA114EKA 100 1/4W 4.7 0 5.6 R635 SW Q609 KTC3875S_Y_RTK 0 0.8 0 KA 330 1/4W R629 3W 27
(MAIN PCB)
8
7
REG Q604 KTC3203_Y
4.9
7.2 5.5 5.5
7
16V 47 YK C645
C619_1
16V 47 YK
C624
1 50V
0.0082
FROM MICON/TUNER R613 PROTECT_H 1K 1/4W
R628
C630
R639
1.5K
C647
100
50V 2.2
1SS133
D601
R638
R633
KA
7
15P CH
C616
NA
C635
8.2K
22K
50V 1 YK
C638
100DT3R531 3.579545MHz
C629_1
R616_1
50V 1
6
R612 4.7K
X602
CF603 SFSRA4M50CF00-A0 1.7 48 49 5.6 2.2 NC 2.3 2.5 8.6 47 0 NC 0 46 NC
R646
10M
47K
50V 10
C627
R608
R642 1K
D605 11E1-EIC
6
C634 100P CH
VIDEO/CHROMA GND
VIDEO/CHROMA GND
NC 7.9 2.5 8.7 2.8 4.7 4.7 2.5 45 44 43 42 41 40 39 38 VIDEO CHROMA Vcc VIDEO CHROMA Vcc NC VREG Vcc fsc OUT 2 EXT C in Hi Vcc TV/Y IN
0 37 CHROMA APC FILTER
3.1 5.6 0 0 36 35 34 33 3.6 32 Y SW OUT MCU RESET fsc OUT 1 31 4.9 5.2 2.8 5.2 4.7 4.7 4.9 2.4 2.8 2.8 2.8 4.9 4.8 4.8 3.6 VD C640 1 F
TO SOUND/AV 5 TUNER_AUDIO SW+8V C655 GND 0.0068 B C604 50V 1 KA
50
QIF OUT AUDIO OUT AUDIO BYPASS EXT AUDIO IN FM DIRECT OUT VIF VCO F/B VIF GND VIF GND VIF VIDEO OUT RF AGC OUT VIF APC FILTER IF AGC FILTER2 IF AGC FILTER1 VIF IN (1) VIF Vcc VIF Vcc V OUT
51
52
53
54
SCL SDA CLOCK CONT
55
L607
15uH
CF604 TPSRA4M50C00-A0
56
R622
68
57
FAST BLK R IN G IN
R615 470 C606 R609 Y_VIDEO AT+5V C618 220 50V 0.47 KA C605 22P CH 100P CH FROM/TO MICON/TUNER RESET
R624 47 1/4W R606 10K 1/4W C602 0.01 F C626 0.01 F C628 50V 0.22 KA
58
59
22
4.5 2.2
23
2.1
24
0
CHROMA IC IC601 M61250BFP
25
C632
50V 0.1
KA
0
26
3.2
27
32 AT5.7V REG OUT
61
62
INV FBP OUT STRAT UP Vcc AFC FILTER DEF GND DEF GND INTELLIGENT MONI R OUT G OUT NC
19
TUNER+5V AGC SAW FILTER CF601 TSF5229P3 IN GNDOUTOUT 1 2 3 4 L601 IF 0.39uH AFT
V RAMP FEEDBACK
4
OSD_BLK
2 AFT OUT
V PULSE OUT
20
2.8 2.8 1.5 1.5
64 VIF IN (2) 1 V RAMP CAP
B IN 17 H VCO F/B 16 B OUT
4.9
H.CTL Q610 KTC3198 3.2 6 220 1/4W H_CTL
60
21
R620
5
C623
0.0033
B
3.1
10K 1/4W
POWER ON CONT
28
3.0
47 8.7V REG OUT 48 LIMITER IN 49 P.Con5.7V REG
34 X'TAL 33 ACL/ABCL
29
30
RESET
5
R648 1M 1/4W SYNC C639
4
0.01 B
FBP IN
H OUT
64
C631
17
R604
63
18
FROM/TO DEFLECTION/CRT
V_OUT OSD_G OSD_B OSD_R 0.01 F ABCL V_FEEDBACK GND 8
C613 63V 1
1 4.6 MKT
2 2.6
3 4.8
4 4.8
5 4.2
6 2.7
7 3.4
8 0
9 0 R626
10 6
11 6 22K 1/4W
12
13 8 NC 0 11
14 15 16 3.6 3.6 3.6 12 13
R601
2.2K
22K 1/4W
HD
9
H_OUT
50V 1 KA
H_SYNC R627 0.01 F R602 1K R630 R631 100 B.OUT 100 G.OUT 100 R.OUT R617 220 CLAMP
3
MKT47.3MC110P-TF
W817 6.3V 100 YK
3
CF602
C621
R641
F
C603
10V 1000 YK
2.2K
2.2K R619
0.01
0.01 F
W820
C637
C607
C601
R605
6.8K
C612
R614
R625
2.2K
GND HD POWER 10 OSD_B OSD_BLK OSD_G VD OSD_R SYNC I2C_OFF SDA SCL TEST POINT CP601 TKC-M07X-A1 R B INT.MONI IIC_OFF SDA SCL GND 7 6 5 4 3 2 1
FROM/TO MICON/TUNER
SCL_TP SDA_TP
2
2
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
CAUTION: DIGITAL TRANSISTOR
PCB010 R.SIGNAL TMD600 G.SIGNAL B.SIGNAL DEFLECTION SIGNAL AUDIO SIGNAL TUNER VIDEO SIGNAL
1
RECORD LUMINANCE SIGNAL
A B C D E F G H
G-3
G-4
A
B
C
D
E
F
G
H
TV POWER SCHEMATIC DIAGRAM
(MAIN PCB)
8 8
CAUTION
2A 125V
4A 125V
:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501) AND 2A 125V (ICP501) FUSE. 4A 125V (F501)
PROTECTION CONTINUE LES ATTENTION :POUR UNEN'UTILISER QUE DES FUSIBLE RISQUES D'INCEIE DE MEME TYPE 4A 125V (F501).
4A 125V (F501) AND 2A 125V (ICP501)
CAUTION:ICP501 AND ICP502 MANUFACTURED BY SKYGATE CO,LTD.
TYPE 20N.
D505 R517
TO SOUND/AV GND SOUND+B C518 500V 470P B C519 16V 1000 YK 21DQ09N 2.2 2W
7
7
SOUND_GND 2.7M 1/2W +-10% 1K 1/4W R504
DEGAUSS COIL L503 8R140032 1 1
1 TH501 B59203-S1060-B14 2 CP502 A1561WV2-2P
R500
CP501 003P-2100
TO DEFLECTION/CRT D510 +B RU2AM-EIC UNREG+12V C521_1 C517_1 2KV 820P RR 160V 100 YXF
6
2
6
R501 1N4005-EIC 5.6 5W
R514 0.22 1W R510 1.2M 1/2W
GND
1N4005-EIC
D501
D502
50V 1 YK
R516
1.2M 1/2W
C502 ECQUL 1N4005-EIC 500V 0.001 B D503 1N4005-EIC 3 1 4 2 B
D513 C516 21DQ09N
TO MICON/TUNER MTZJ5.1B 1/4W D517
500V 0.001
200V 220 YK
C503
MTZJ18B
C505
275V 0.1
D504
C526
5
4A 125V F501 51MS040L
D509
R507
16V 1000 YK 1.7 NC 144.0 NC 10.3 10.0 0 7 6 5 4 3 2 12 13 14 15 16 17 18 132.3 0 0 11.3 NC NC 1SS133 D515 B504 W5RH3.5X5X1.0 ICP501 UNREG+12V 20N_2000 TO CHROMA D516 1N4937 R511 100 1/4W R505 3.3K 1/4W
T4A_L_125V FH501 EYF-52BC
FH502 EYF-52BC
COIL,LINE FILTER L501 1R5A102F20
8
11
AC120V_60Hz CD501 0R414903
S501A
W819
4
BLADE WIDE
BLACK WHITE R
W804
3.3K
T502 81291234
POWER_FAIL +B
C515
5
BLACK C514 2KV 680P WHITE S501B C506 250V 0.0047 KX
6.6 10.3 R508 G 4.8 220 1W 1SS133 C509 D512 1SS133 0.047 M D508
2A 125V
4
144.0 D 0.1 S
D518 MTZJ4.3B
2.7K 1/4W
W821
R506
12K 1/4W
R520
1/4W
3
0.68 1W R542
220
0.1 0.0082 M C501
W802
0 HS501 763WSAA013
MTZJ18B
BUFFER Q502 KTC3198 4.8
C511 W832 50V 1 KA D506
R509
100 1/4W
R528
FET Q501 2SK3563(ORION_Q)
3
1SS133
W811
R513
FEED BACK 9.5 SWITCHING Q507 6.0 KTC3198 5.5
D511
120K 1/2W
0.1 F
C513
R515
1SS133 D522
2
2.2K
1/4W
1SS133
D514
11.5 4
10.5 1
R512 680 1/4W
R519 1.2K 1/4W W815
2
3
MTZJ5.6B
FEED BACK 0.1 IC501 PS2561AL1-1-V(W)
2 9.5 D528
5.6K +-1%
PCB010 TMD600
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
R518
1
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION
:LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. G H
A
B
C
D
E
F
G-5
G-6
A
FROM CHROMA CLAMP
B
C
D
E
CP802A B2013H02-5P GND 1 GND CLAMP G.OUT R.OUT B.OUT CLAMP G.OUT R.OUT B.OUT HEATER GND NC 180V 2 3 4 5 * 1 2 3 4 1 2 3 4 CD803 CD802 * 1 2 3 4 5 CP802B B2013H02-5P GND GND CLAMP CLAMP G.OUT G.OUT R.OUT R.OUT B.OUT B.OUT B2013H02-4P HEATER GND NC 180V CP801 TBS-X01X-A1
F
G
H
(MAIN PCB) DEFLECTION/CRT SCHEMATIC DIAGRAM
8
G.OUT R.OUT B.OUT V-OUT IC IC401 LA78040N-E
THERMAL PROTECTION PUMP UP AMP
8
CP803A HEATER GND NC 180V 7 25.0 3.5
B2013H02-4P
CP803B
HEATER GND NC 180V
1/4W
35V 100 YK
C414
1
1 220uH L801
4.7K
3.5
25.0
2.0
0
12.0
7
14 R423 R424 470 1/4W 100 1/4W
3.2 100.6 2.7 98.4
3.2 2.7
4.7K
CD801_1 0
4.7K
R811
1
2
3
4
5
6
RED OUT Q801 2SC1473A
GREEN OUT Q802 2SC1473A 3.2
1/4W
BLUE OUT Q803 2SC1473A
R809
R814
1/4W
95.4 2.7
7
D403
100V 0.15 MKT
19 330 1/2W
11E1-EIC
V801 A34AGT13X98(L) 9 10 8 6 11
C422
R418 R419 22K 1/4W R417 10K
R420
25V 470 YK 50V 10 560 YK
R410
390P B
R813
390P B
390P B
R815
C810
330
C418
1 1/2W
R416
1.8K
1/2W 50V 10 YK
5 7 1
C417
2.2 1/2W
2.2K 1/2W
R413
6
R422
HS401 763WSAA013
C427
TO DY 5 4 CP401 A1561WV2-A5P 3 NC 2 1 20 21 22
C809
330
3.3K
R415
C808
R816
R G B
330
6
22 YK
AU02A-EIC
C434
TP022
TP024
D411
TP023
10K +-1%
100V
R429_1 4.7 3W
MTZJ5.1B
R408
D412
1W
2.7K 1/4W
1W
+-1%
1/2W
R802
R804
R409
R803
5
R806
R401 X-RAY 27K +-1% +B
2.7K 1/4W
27K
FROM/TO MICON/TUNER
1
HV
2.7K
130.0
COL
15K
15K
15K
FB401
FNI14B002_M
R805
R807
1W
5
132.5 VIDEO 6 132.5 2 B+ AFC 9 8 GND
F S
250V 0.47 PMS
GND 11 ABL 7 4.3 W898
48.0 0
15 FROM/TO CHROMA
C437
T401 ETH09K14BZ 3 4 6 16
130.0 0
HEATER 7.0 10 5 GND 8 NC
GND
4
V_FEEDBACK V_OUT ABCL H_OUT H_SYNC
0.3 0 C440
100 1/4W
MMTS
R427
CMPP
H.DRIVE Q402 2SC1627_Y 27.0
470 1/2W
R446
NC 2 1
E12 NC 4 25.0 E25 3
17
4
100V 0.01
50V 22 YK
C443_1
130.0 0 0
H.OUTPUT Q401 TT2140LS-CBC
0.0086
FOCUS FOCUS
GND HS402 763WSA0017 B_SHORT +B R403 22K 1/4W W809 C406
SCREEN
C819
SCREEN
2KV 0.001 B
FROM TV POWER
1.25KV
SCREEN CP806
C446
96.4
100.6 9 7 100.6
3
3
F 1 0 99.6
J801 ISMS01S
101.6 0
4 6 5
8
0
3
0
6.4
500V 100P B MTZJ6.2B D404
R447 UNREG+12V 150 2W
D406 11E1-EIC AU02A-EIC D405
W810
2
11E1-EIC D409
PCB110 TCD456
2
AU02A-EIC
D410
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
R448 560 1/2W R449 560 1/2W 250V 22 YK 35V 470 YK R445_1 100V 0.1 MHE 220K 1/4W D408 180K 1/4W C435 11E1-EIC C403 C448 R421
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
R.SIGNAL G.SIGNAL B.SIGNAL DEFLECTION SIGNAL
G H 1
1
PCB010 TMD600
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
A
B
C
D
E
F
G-7
G-8
A
B
C
D
E
F
G
H
SOUND/AV SCHEMATIC DIAGRAM
8
(MAIN PCB)
FRONT JACK RCA JACK(RED) J703 MTJ-032-05A-31-FE
NC
8
27
R705 820 NC
3
2
H
1
E
NC
28
R703 820
H
RCA JACK (WHITE) J702 MTJ-032-05A-32-FE RCA JACK (YELLOW) J701 MTJ-032-05A-30-FE
3
2
NC
29 AV2_VIDEO_IN R704 47K 47K AV2_A_IN_L R701 75
NC R702
3
2
7
H
1
E
1
E
C713 0.1 F
7
C714 16V 100 YK C715 Vcc V.OUT SW1 Vin2 GND Vin1 3 4 5.3 VIDEO_IN 5.0 1 47uH 0305 6 3.3 2 5 0 5.8 16V 10 KA R711 C716_1 16V 10 KA 75
AV2_A_IN_R
FROM/TO CHROMA
J704 MSP-213V2-432_NI_LF
H1 NC H1 H2
30
R L
R708 820 R709 820
4
RAER JACK
2
6
R706
47K R707
L702
47K
5
AV1_VIDEO_IN
V
32
31
3
E
1
E
6
VIDEO SW IC IC703 MM1501XNRE AV1_A_IN_R AV1_A_IN_L
W908
W909
1 5 C1014 C1013 25V 47 YK 25V 47 YK R1009 R1008 47 47 1/2W 1/2W 2 6 7 4 3 HEADPHONE_JACK J1001 MSJ-2000_AG
6
C711
C712
C706
C707
1 F
1 F
F
1
1
F
BAIAS
SW+8V
BAIAS
5
4
3
2
1
4
3
2
1
TUNER/AV1/AV2 Rch SW IC IC702 NJM2534V
TUNER/AV1/AV2 Lch SW IC IC701 NJM2534V
4.8 TUNER_AUDIO
4.6
4.8
4.7
4.8
4.6
4.8
4.7
CD1002 PJ070044
SPEAKER SP1001 S08F21 8 OHM J1150 (RED)
5
CH
C1150
5.2 C705
5
9.1 F
6
7
0
8
5.2 C709
5
9.1 1 F
6
7
0
8
S1150 R S1151 CP1001 A2502WV2-4P R 1 2 3 4 CD1001 CH145901 1 2 3 4 R JACK R JACK L L S1152 L JACK R JACK-R TEDB44
MTJ-032-05A-32-FE NC
H
BUFFER
BUFFER
2 1
NC
3
100P
E
L701 C710 47uH 0305 C708 FROM TV POWER 0.1 F 16V 100 YK
1
CC001
JACK R 24 26 JACK L L
4
GND
J1151
(WHITE)
4
MTJ-032-05A-31-FE NC CH
H
C1151
2 1
NC
3
SOUND_GND SOUND+B
S1153 JACK L JACK-L TEDB43 8.2 5 6 3.5 7 0 8 3.4 SOUND AMP IC(Rch) IC IC1001 AN7513 5 8.2 6 3.5 7 0 8 3.4 SOUND AMP IC(Lch) IC IC1002 AN7513
100P
E
FROM MICON/TUNER
CD1003 PJ070044
SPEAKER SP1002_1 S08F21 8 OHM
3
AV1 W803 AV2
+
-
+
-
3
4 R1001 VOLUME 47K R1003 POWER KA 5.1
3 0
2 0.3
1 3.9
4 5.1
3 0
2 0.3
1 3.9
R1002 47K 1/4W KA
25V 10 KA
560P CH
2
C1001_1 0.022 F C1002_1 0.022 F R1010 220K R1011 220K PCB010 TMD600 25 23
50V
50V
W808
560P CH
R1004
R1005
C1005
270K
R1006
C1003
C1007
68K
1/4W 47K
C1004
47K
1
C1008
1
2
1
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
TUNER VIDEO SIGNAL AUDIO SIGNAL
1
A
B
C
D
E
F
G
H
G-9
G-10
WAVEFORMS
MICON/TUNER
1 1V 0.1µs/div
7 200mV 20µs/div
12 1V 20µs/div
3 200mV 20µs/div
8
20V 20µs/div
13 1V 20µs/div
DEFLECTION/CRT
4 200mV 5ms/div
9
200mV 20µs/div 14 0.5V 5ms/div
CHROMA
5 0.5V 2ms/div
10 0.5V 5ms/div
15 20V 20µs/div
6 0.5V 20µs/div
11 1V 20µs/div
16 2V 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
WAVEFORMS
SOUND/AV
17 200V 20µs/div
23 200mV 1ms/div
28 200mV 500µs/div
19 10V 5ms/div
24 0.5V 1ms/div
29 500mV 20µs/div
20 50V 20µs/div
25 200mV 1ms/div
30 200mV 500µs/div
21 50V 20µs/div
26 0.5V 1ms/div
31 200mV 500µs/div
22 50V 20µs/div
27 200mV 500µs/div
32 500mV 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
MECHANICAL EXPLODED VIEW
205 106 205 202 PCB110 (CRT PCB ASS'Y) J801 205
206 117
205 205 105
116
103 206
117
206
102A 102D
102B 201
201 102D
102C
L503 117 116 V801 117 116 203 204
112 202 110 111
116 206
102 204
118
PCB010 (MAIN PCB ASS'Y)
202
202 202
202 121I 121F 121C 121G 121J
202
SP1002 121H SP1001 202
202
PCB260A (FRONT JACK PCB ASS'Y)
205 114 108 107 104
121
121E
121A 121G
202 113
121F
205
121B
121D
101G PCB260B 115 (FRONT JACK PCB ASS'Y) 101F 202 202 101E 101D 101B 101 201 101I
101A 119 PCB270 (OPERATION PCB ASS'Y)
202
101H 202
109
202 101C 201 101I
120
I-1
202
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO.
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! R401 R408 R409 R429 R447 R500 R501 R508 R509 R514 R515 R517 R518 R519 R542 R629 R803 R805 R807 C403 C414 C418 C434 C437 C443 C446 C448 C503 C505 C506 C514 C515 C517 C519 C521 C526 C715 C716 C819 D001 D103 D104 D403 D404 D405 D406 D408 D409 D410 D411 D412 D501 D502 D503 D504 D505 D506 D508 D509 D510 D511 D512 D513 D514 D515 D516 D517 D518 D522 D528 D601 D602 D605 R4X5T6273F R4X5T6103F R4X5T6273F R3X28B4R7J R3X28A151J R0G3K2275K R5Y2CD5R6J R3X181221J R002T4221J R63581R22J R002T2124J R3X28A2R2J R4X5T6562F R002T4122J R3X181R68J R3X28B270J R3X181153J R3X181153J R3X181153J E02LT4471M E02LU4101M E02LT3471M E02LU8220M P4J7F3474J P4N8FJ862H E02LU5220M E0ELFD220M C0JTB0513K P2122B104M CD39E0MQ3M C0PLRR7U2K E02LT2102M C0PLRR7W2K E02LT2102M E62NFB101M E02LFC221M E52H02100M E50HU2100M E52H02100M E50HU2100M C0JBB0713K D97U03301B D97U05R61B D97U05R61B D2WT011E10 D97U06R21B D2WTAU02A0 D2WT011E10 D2WT011E10 D2WT011E10 D2WTAU02A0 D2WTAU02A0 D97U05R11B D2WXN40050 D2WXN40050 D2WXN40050 D2WXN40050 D28T21DQN9 D97U01801B D1VT001330 D97U01801B D2WXRU2AM0 D1VT001330 D1VT001330 D28T21DQN9 D1VT001330 D1VT001330 D2WXN49370 D97U05R11B D97U04R31B D1VT001330 D97U05R61B D1VT001330 D97U08R21B D2WT011E10
DESCRIPTION RESISTORS
R,METAL R,METAL R,METAL R,METAL OXIDE R.METAL OXIDE RC R,CEMENT R,METAL OXIDE RC R,FUSE RC R,METAL OXIDE R,METAL RC R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE 27K OHM 1/6W 10K OHM 1/6W 27K OHM 1/6W 4.7 OHM 3W 150 OHM 2W 2.7M OHM 1/2W 5.6 OHM 5W 220 OHM 1W 220 OHM 1/4W 0.22 OHM 1W 120K OHM 1/2W 2.2 OHM 2W 5.6K OHM 1/6W 1.2K OHM 1/4W 0.68 OHM 1W 27 OHM 3W 15K OHM 1W 15K OHM 1W 15K OHM 1W 470 UF 35V 100 UF 35V 470 UF 25V 22 UF 100V 0.47 UF 250V PMS 0.0086UF 1.25KV 22 UF 50V 22 UF 250V 0.001 UF 500V B
0.1 UF 275V ECQUL
REF. NO. PART NO. ICS
! IC101 IC199 ! IC401 ! IC501 IC601 IC701 IC702 IC703 ! IC1001 IC1002 Q401 Q402 Q501 Q502 Q507 Q601 Q603 Q604 Q605 Q606 Q609 Q610 Q611 ! Q801 ! Q802 ! Q803 L001 L101 ! L501 ! L503 L601 L607 L701 L702 L801 T401 ! T502 J701 J702 J703 J704 ! J801 J1001 J1150 J1151 SW2001 SW2002 SW2003 SW2004 SW2005 SW2006 SW2007 PCB010 PCB110 PCB270 PCB260A PCB260B B504 ! CD501 CD802 CD803 CF601 CF602 CF603 CF604 CP101 ! CP401 CP501 ! CP502 CP601 ! ! ! ! I56D07108A A3P902G015 I03TD804N0 000220002W I06FC1250B I0QF02534V I0QF02534V I0UF015010 I01DP75130 I01DP75130 TD3U021400 TC5T01627Y T25F035630 TCATC31980 TCATC31980 TCAT032034 TCAT032034 TCAT032034 TCAT032034 TCAT032034 TCAA3875SY TCATC31980 TPYJB05001 TCKT1473A0 TCKT1473A0 TCKT1473A0 02167F470J 021LA63R9K 029T00A7M1 028R140032 021LA6R39M 021LA6150J 02167F470J 02167F470J 021673221K 045009003J 0481291234 060J421036 060J421037 060J421030 060J431020 066F120018 060J131016 060J421037 060J421030 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 A3P902G010 A3P902G110 A3P902G270 A3P902G260 A3P902G260 024HT03553 120R414903 1209414909 WCL6842038 WBL6028038 1029045R7G 1012T04702 1012T4R520 1012T4R519 069S250629 069S450089 069D01001A 069S420110 0697270650
DESCRIPTION
IC INIT DATA IC PHOTO COUPLER IC IC IC IC IC IC OEC7108A LA78040N-E
PS2561AL1-1-V(W)
M61250BFP NJM2534V(TE2) NJM2534V(TE2) MM1501XNRE AN7513 AN7513 TT2140LS-CBC 2SC1627_Y(TPE2)
2SK3563(ORION_Q)
TRANSISTORS
TRANSISTOR SILICON TRANSISTOR SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR, SILICON TRANSISTOR, SILICON TRANSISTOR, SILICON TRANSISTOR, SILICON TRANSISTOR, SILICON TRANSISTOR SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR SILICON TRANSISTOR SILICON TRANSISTOR SILICON COIL COIL COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
CAPACITORS
CE CE CE CE CMPP CMPP CE CE CC CMP CC CC CE CC CE CE CE CE CE CE CE CC
KTC3198-AT(Y,GR) KTC3198-AT(Y,GR) KTC3203_Y-AT KTC3203_Y-AT KTC3203_Y-AT KTC3203_Y-AT KTC3203_Y-AT KTC3875S_Y_RTK KTC3198-AT(Y,GR) DTA114EKAT146 2SC1473A-TA-(RQ) 2SC1473A-TA-(RQ) 2SC1473A-TA-(RQ) 47 UH 3.9 UH 1R5A102F20 8R140032 0.39 UH 15 UH 47 UH 47 UH 220 UH ETH09K14BZ 81291234
MTJ-032-05A-30-FE MTJ-032-05A-32-FE MTJ-032-05A-31-FE MSP-213V2-432_NI_LF
COILS &TRANSFORMERS
0.0047UF 250V 680 PF 2KV R 1000 UF 16V 820 PF 2KV RR 1000 UF 16V 100 UF 160V 220 UF 200V 10 UF 16V or 10 UF 16V 10 UF 16V or 10 UF 16V 0.001 UF 2KV B MTZJ33B T-77 MTZJ5.6B T-77 MTZJ5.6B T-77 11E1-EIC MTZJ6.2B T-77 AU02A-EIC 11E1-EIC 11E1-EIC 11E1-EIC AU02A-EIC AU02A-EIC MTZJ5.1B T-77 1N4005-EIC 1N4005-EIC 1N4005-EIC 1N4005-EIC 21DQ09N-TA2B1 MTZJ18B T-77 1SS133T-77 MTZJ18B T-77 RU2AM-EIC 1SS133T-77 1SS133T-77 21DQ09N-TA2B1 1SS133T-77 1SS133T-77 1N4937 MTZJ5.1B T-77 MTZJ4.3B T-77 1SS133T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 11E1-EIC
JACKS
RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY T HEADPHONE JACK RCA JACK RCA JACK
D I O D ES
DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE SILICON DIODE,ZENER DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE,ZENER DIODE SILICON DIODE SILICON DIODE SILICON DIODE SILICON DIODE SCHOTTKY DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE SILICON DIODE,SILICON DIODE,SILICON DIODE SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE SILICON
UBEISMS01S MSJ-2000_AG MTJ-032-05A-32-FE MTJ-032-05A-31-FE EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R TMD600A TCD456A TEDB42A TEDB43A TEDB44A W5RH3.5X5X1.0 0R414903 9414909
!
SWITCHES
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT PCB ASS'Y PCB ASS'Y PCB ASS'Y PCB ASS'Y PCB ASS'Y
! ! ! ! ! ! ! !
P.C.BOARD ASSEMBLIES
! !
MISCELLANEOUS
CORE,BEADS CORD AC BUSH CORD AC BUSH FLAT CABLE AWM2468 FLAT CABLE AWM2468 FILTER,SAW FILTER,CERAMIC TRAP FILTER,CERAMIC FILTER,CERAMIC TRAP CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE or
!
AWG26 5C GRAY 420MM AWG26 4C BLACK 280MM
TSF5229P3
MKT47.3MC110P-TF SFSRA4M50CF00-A0 TPSRA4M50C00-A0
!
A2001WV2-5P A1561WV2-A5P 003P-2100 A1561WV2-2P TKC-M07X-A1
J2-1
ELECTRICAL REPLACEMENT PARTS LIST
REF. NO. PART NO. DESCRIPTION MISCELLANEOUS
CP801 CD1001 CD1002 CD1003 CD2001 CP1001 CP802A CP802B CP803A CP803B F501 FB401 FH501 FH502 ICP501 OS2001 SP1001 SP1002 TH501 TM101 TU001 V801 X101 X602 069W010030 06CH145901 06CXB07001 06CXB07001 06CU251801 069S140419 067U005049 067U005049 067U004029 067U004029 081PC04005 043214050F 06710T0006 06710T0006 0845C02003 077Q037002 070Y132018 070Y132018 D8EE0B1400 076N0JK020 0145K00062 098Q1404B2 100CT8R005 100DT3R531 CONNECTOR PCB SIDE CORD CONNECTOR CORD,RCA PIN CORD,RCA PIN CORD CONNECTOR CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE IC PROTECTOR REMOTE RECEIVER SPEAKER SPEAKER DEGAUSS ELEMENT TRANSMITTER TUNER,VHF-UHF CRT W/DY CRYSTAL CRYSTAL TBS-X01X-A1 CH145901 PJ070044 PJ070044 CU251801 A2502WV2-4P B2013H02-5P B2013H02-5P B2013H02-4P B2013H02-4P 51MS040L FNI14B002_M EYF-52BC EYF-52BC 20N_2000 PIC-37143TH5 S08F21 S08F21
B59203-S1060-B14
! !
!
! ! !
RC-JK020
TECC1040PG38W A34AGT13X98(L)
HC-49/U-S HC-49/U
RESISTOR RC................... CARBON RESISTOR CAPACITORS CC................... CERAMIC CAPACITOR CE................... ALUMI ELECTROLYTIC CAPACITOR CP................... POLYESTER CAPACITOR CPP.................. POLYPROPYLENE CAPACITOR CPL.................. PLASTIC CAPACITOR CMP................... METAL POLYESTER CAPACITOR CMPL................ METAL PLASTIC CAPACITOR CMPP................ METAL POLYPROPYLENE CAPACITOR
J2-2
SPEC.NO. O/R NO.
M3P9-02G K423007