Text preview for : strdh510.pdf part of Sony STR-DH510 STR-DH510
Back to : strdh510.pdf | Home
STR-DH510
SERVICE MANUAL US Model
Ver. 1.0 2010.01
Canadian Model
This receiver incorporates Dolby* Digital and Pro Logic Surround and the SPECIFICATIONS
DTS** Digital Surround System.
* Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, AUDIO POWER SPECIFICATIONS
and the double-D symbol are trademarks of Dolby Laboratories.
** Manufactured under license under U.S. Patent #'s: 5,451,942; 5,956,674; POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents (Models of area code US only)
issued & pending. DTS and DTS Digital Surround are registered With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 90
trademarks and the DTS logos and Symbol are trademarks of DTS, Inc. watts per channel minimum RMS power, with no more than 0.09% total
© 1996-2008 DTS, Inc. All Rights Reserved. harmonic distortion from 250 milliwatts to rated output.
This receiver incorporates High-Definition Multimedia Interface (HDMITM) Amplifier section
technology. HDMI, the HDMI Logo, and High-Definition Multimedia Models of area code US1)
Interface are trademarks or registered trademarks of HDMI Licensing LLC Minimum RMS Output Power (8 ohms, 20 Hz 20 kHz, THD 0.09%)
in the United States and other countries. 90 W + 90 W
Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%)
"x.v.Colour (x.v.Color)" and "x.v.Colour (x.v.Color)" logo are trademarks 100 W + 100 W
of Sony Corporation. Surround Mode Output Power2) (8 ohms, 1 kHz, THD 10%)
130 W per channel
"BRAVIA" is a trademark of Sony Corporation. Models of area code CND1)
Minimum RMS Output Power (8 ohms, 20 Hz 20 kHz, THD 0.09%)
"PLAYSTATION" is a trademark of Sony Computer Entertainment Inc. 85 W + 85 W
Stereo Mode Output Power (8 ohms, 1 kHz, THD 1%)
100 W + 100 W
Surround Mode Output Power2) (8 ohms, 1 kHz, THD 10%)
130 W per channel
Continued on next page
MULTI CHANNEL AV RECEIVER
9-890-535-01 Sony Corporation
2010A80-1 Audio & Video Business Group
© 2010.01 Published by Sony EMCS (Malaysia) PG Tec
STR-DH510
1)
Measured under the following conditions: Video section
Area code Power requirements Inputs/Outputs
US, CND 120 V AC, 60 Hz Video: 1 Vp-p, 75 ohms
COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms
PB/CB: 0.7 Vp-p, 75 ohms
2)
Reference power output for front, center and surround speakers.
PR/CR: 0.7 Vp-p, 75 ohms
Depending on the sound field settings and the source, there may be
80 MHz HD Pass Through
no sound output.
Frequency response General
Analog 10 Hz 70 kHz, Power requirements
+0.5/2 dB (with sound Area code Power requirements
field and equalizer bypassed) US, CND 120 V AC, 60 Hz
Input
Analog Sensitivity: 500 mV/
Power output (DIGITAL MEDIA PORT)
50 kohms
DC OUT: 5 V, 0.7 A MAX
S/N3) : 96 dB
(A, 500 mV4))
Digital (Coaxial) Impedance: 75 ohms Power consumption
S/N: 100 dB Area code Power consumption
(A, 20 kHz LPF) US, CND 230 W
Digital (Optical) S/N: 100 dB
(A, 20 kHz LPF) Dimensions (width/height/depth) (Approx.)
Output (analog) 430 mm × 157.5 mm × 322 mm
AUDIO OUT Voltage: 500 mV/ (17 in × 6 1/4 in × 12 3/4 in) including
10 kohms projecting parts and controls
SUBWOOFER Voltage: 2 V/1 kohm Mass (Approx.) 7.4 kg (16 lb 6 oz)
Equalizer
Gain levels ±6 dB, 1 dB step Supplied accessories
3)
INPUT SHORT (with sound field and equalizer bypassed). · Operating Instructions
· Quick Setup Guide
4)
Weighted network, input level. · FM wire antenna (aerial) (1)
FM tuner section
Tuning range 87.5 MHz 108.0 MHz
Antenna (aerial) FM wire antenna (aerial) · AM loop antenna (aerial) (1)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency 10.7 MHz
AM tuner section · Remote commander (1)
Tuning range RM-AAU071 (Models of area code US, CND only)
Area code Tuning scale
10 kHz step 9 kHz step
US, CND 530 kHz 531 kHz
1,710 kHz 1,710 kHz
Antenna (aerial) Loop antenna (aerial)
Intermediate frequency 450 kHz · R6 (size-AA) batteries (2)
Design and specifications are subject to change without notice.
· Standby power consumption: 0.3 W
· Halogenated flame retardants are not used in the certain
printed wiring boards.
Abbreviation
CND : Canadian model
2
STR-DH510
SAFETY CHECK-OUT MODEL IDENTIFICATION
After correcting the original service problem, perform the follow- BACK PANEL
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, "metallized" knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.). Part No.
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these Model Part No.
instruments. US 4-164-299-0[]
2. A battery-operated AC milliammeter. The Data Precision 245
Canadian 4-164-299-1[]
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The "limit" indication Notes on chip component replacement
is 0.75 V, so analog meters must have an accurate low-voltage · Never reuse a disconnected chip component.
scale. The Simpson 250 and Sanwa SH-63Trd are examples · Notice that the minus side of a tantalum capacitor may be
of a passive VOM that is suitable. Nearly all battery operated damaged by heat.
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
To Exposed Metal (Caution: Some printed circuit boards may not come printed with
Parts on Set
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
· Unleaded solder melts at a temperature about 40 °C higher
AC than ordinary solder.
0.15 F 1.5 k voltmeter Ordinary soldering irons can be used but the iron tip has to be
(0.75 V) applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
Earth Ground
· Strong viscosity
Fig. A. Using an AC voltmeter to check AC leakage. Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
· Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE OF REPLACING THE IC3500 AND IC3501 ON THE
HDMI BOARD
IC3500 and IC3501 on the HDMI board cannot exchange with
single. When these parts on the HDMI board are damaged,
exchange the entire mounted board.
SAFETY-RELATED COMPONENT WARNING! ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
REPLACE THESE COMPONENTS WITH SONY PARTS PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
3
STR-DH510
TABLE OF CONTENTS
1. DISASSEMBLY
1-1. Case ..................................................................................... 5
1-2. Back Panel Section ............................................................. 6
1-3. Front Panel Section ............................................................. 6
1-4. Digital Board....................................................................... 7
1-5. Main Board Section ............................................................ 7
2. TEST MODE ...................................................................... 8
3. FM TUNER CHECK .......................................................11
4. DIAGRAMS
4-1. Block Diagram Tuner/Audio Section .......................... 12
4-2. Block Diagram Digital Section .................................... 13
4-3. Block Diagram Video Standby Section ....................... 14
4-4. Block Diagram HDMI PC Section .............................. 15
4-5. Block Diagram Key/Display Section .......................... 16
4-6. Block Diagram Power Key Section ............................. 17
4-7. Printed Wiring Boards Main Section ........................... 19
4-8. Schematic Diagram Main Section (1/3) ...................... 20
4-9. Schematic Diagram Main Section (2/3) ...................... 21
4-10. Schematic Diagram Main Section (3/3) ...................... 22
4-11. Printed Wiring Board Digital Section (1/2) ................. 23
4-12. Printed Wiring Board Digital Section (2/2) ................. 24
4-13. Schematic Diagram Digital Section (1/3) .................... 25
4-14. Schematic Diagram Digital Section (2/3) .................... 26
4-15. Schematic Diagram Digital Section (3/3) .................... 27
4-16. Printed Wiring Board Video Standby Section ............. 28
4-17. Schematic Diagram Video Standby Section ................ 29
4-18. Printed Wiring Board HDMI PC Section (1/2) ........... 30
4-19. Printed Wiring Board HDMI PC Section (2/2) ........... 31
4-20. Schematic Diagram HDMI PC Section (1/2) .............. 32
4-21. Schematic Diagram HDMI PC Section (2/2) .............. 33
4-22. Printed Wiring Boards
Headphone, Power Key Section ..................................... 34
4-23. Schematic Diagram
Headphone, Power Key Section .................................... 34
4-24. Printed Wiring Board Display Section ........................ 35
4-25. Schematic Diagram Display Section ........................... 36
4-26. Printed Wiring Boards
Temp-Sensor, Connection Section ................................. 37
4-27. Schematic Diagram
Temp-Sensor, Connection Section ................................. 37
5. EXPLODED VIEWS
5-1. Case Section ...................................................................... 50
5-2. Front Panel Section............................................................ 51
5-3. Back Panel Section ............................................................ 52
5-4. Chassis Section .................................................................. 53
6. ELECTRICAL PARTS LIST ....................................... 54
4
STR-DH510
SECTION 1
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
1-1. CASE
(Page 5)
1-2. BACK PANEL SECTION
(Page 6)
1-3. FRONT PANEL SECTION 1-4. DIGITAL BOARD
(Page 6) (Page 7)
1-5. MAIN BOARD SECTION
(Page 7)
Note: Follow the disassembly procedure in the numerical order given.
1-1. CASE
3 two screws
1 two screws (+BVTP 3 8)
4 case
2 two screws
(for Canadian model only)
5
STR-DH510
1-2. BACK PANEL SECTION
1 CNP901 (2P)
2 CN906 (4P) 9 five screws
(+BVTP 3 8)
0 six screws
4 CNP902 (2P)
(+BVTP 3 8)
3 CN907 (3P)
qa three screws
5 CNS203 (6P) (+BVTP 3 8)
6 wire (flat type) (9 core)
(CN2201)
7 wire (flat type) (19 core)
(CN2601)
8 CNS271 (17P)
(for Canadian model only)
1-3. FRONT PANEL SECTION
1 CNP792 (4P)
5 sheet, insulation
6 cushion, saranet
(for Canadian model only)
wire (flat type) (15 core)
(CN2106)
3 five screws
(+BVTP 3 8)
4 front panel section
6
STR-DH510
1-4. DIGITAL BOARD
1 CN2501 (4P)
2 DIGITAL board
3 TEMP SENSOR board
CNP412 (18P)
CNP410 (15P)
1-5. MAIN BOARD SECTION
CONNECTION board
CNS170 (6P)
two screws
(+BVTP 3 x 8 )
two screws
(+BVTP 3 x 8)
CNP920 (5P)
MAIN board section
7
STR-DH510
SECTION 2
TEST MODE
AM CHANNEL STEP 9 kHz/10 kHz SELECTION MODE KEY CHECK MODE
(US, Canadian model only) * Button check
* Either the 9 kHz step or 10 kHz step can be selected for the AM * Procedure:
channel step. 1. While depressing the [TUNING +] and the [MUTING] but-
* Procedure: tons simultaneously, press the [?/1] button to turn on the main
Turn the [INPUT SELECTOR] control to set AM and press the power.
[?/1] button to turn off the main power. 2. The message "REST 12" appears.
1. While depressing the [TUNING MODE] button, press the 3. Every pressing of any button other than the [?/1] counts down
[?/1] button to turn on the main power. the buttons. The buttons which are already counted once are
2. Either the message "9K STEP" or "10K STEP" appears for a not counted again. When all buttons are pressed "REST 00"
moment and select the desired step. appears.
VACUUM FLUORESCENT DISPLAY TEST MODE SWAP ALL MODE
* All fluorescent segments are tested. * The signal will be swap to all channel so that all speaker will
When this test is activated, all segments light on at the same time, have sound output.
then each segment lights on one after another. * Procedure:
* Procedure: 1. While depressing the [TUNING MODE] and the [MOVIE]
While depressing the [TUNING +] and the [DIMMER] buttons buttons simultaneously, press the power [?/1] button to turn
simultaneously, press the [?/1] button to turn on the main pow- on the main power.
er. 2. "SWAP.MODE" appears. (No change while displayed.)
1. ALL segments light on.
SHIPMENT MODE
LH RH SW LFE HDMI DTS -ES 96/24 NEO:6 S-AIR PL II x z TrueHD * All preset contents are reset to the default setting.
COAX OPT DTS-HD MSTR HI RES LBR LPCM D + EX SLEEP
L C R AAC ST D.RANGE * Procedure:
dB RDS
SL S SR
k Hz m 1. While depressing the [TUNING MODE] and the [DIMMER]
SBL SB SBR MHz ft.
buttons simultaneously, press the power [?/1] button to turn
on the main power.
2. The message "CLEARING" appears.
2. Press the [DISPLAY] button, confirm display. 3. After a few seconds, "CLEARED" appears and switch off the
set.
LH RH SW LFE HDMI DTS -ES 96/24 NEO:6 S-AIR PL II x z TrueHD
COAX OPT DTS-HD MSTR HI RES LBR LPCM D + EX SLEEP
L C R AAC ST D.RANGE PROTECTOR AUTO OFF
dB RDS
SL S SR
k Hz m * To disable auto off after protector occur.
SBL SB SBR MHz ft.
* Procedure:
1. While depressing the [INPUT MODE] and the [A.F.D.] but-
tons simultaneously, press the power [?/1] button to turn on
3. Press the [DISPLAY] button, confirm display. the main power.
2. "PROTECT" appears.
LH RH SW LFE HDMI DTS -ES 96/24 NEO:6 S-AIR PL II x z TrueHD
COAX OPT DTS-HD MSTR HI RES LBR LPCM D + EX SLEEP
L C R AAC ST D.RANGE
SL S SR dB RDS
k Hz m
SBL SB SBR MHz ft.
4. Press the [DISPLAY] button, all segments light off.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon com-
pletion of repair.
* Procedure:
1. While depressing the [MUSIC] button, press the [?/1] button
to turn on the main power.
2. The message "S.F. CLEAR" appears for a moment and initial-
ization is performed.
SOFTWARE VERSION CHECK MODE
* The software version is displayed.
* Procedure:
1. While depressing the [TUNING MODE] and the [DISPLAY]
buttons simultaneously, press the [?/1] button to turn on the
main power.
2. The model name, destination and the software version are
displayed for a moment.
8
STR-DH510
HISTORY MODE DCAC TEST MODE
* The state that the set is used is memorized. Procedure:
* Procedure: 1. While pressing [INPUT MODE] and the [MOVIE] buttons,
1. While depressing the [INPUT MODE] and the [MUSIC] press the [?/1] button to turn on the main power.
buttons simultaneously, press the [?/1] button to turn on the 2. The message "DCAC FTM" appears.
main power. SOURCE : normal mode
2. "HISTORY" appears. MIC IN : mode that output audio from mic input.
3. Each time the [] / [] buttons on the remote commander is 3. Afterward, press the [DISPLAY] to start DCAC factory test
pressed, the item is switched in order as follows. mode.
Items INITIALIZE MODE
Protector Count COUNT XX All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
Total single power on time XXXXXHXX 01
of repair.
Sound Field SND FLD Procedure:
Input function FUNCTION 1. While pressing the [TUNING MODE] and [MUTING] but-
Input Mode INP MODE tons, press the [?/1] button to turn on the main power.
Digital Select DIG IN 2. The message "CLEARING" appears and the memories are re-
set to the default values.
Stream information STREAM
3. When done, the message "CLEARED" appears.
Signal configuration CO XXXXX
Headphones HP XXX COMMAND MODE CHANGE MODE
Volume VOL XX The command mode of the remote-commander which this set re-
Bass Setting BASS XXX
ceives can be changed.
Procedure:
Treble Setting TREB XXX
1. While pressing the [INPUT MODE] and [2CH/A.DIRECT]
Level FL/FR F XXXXXX buttons, press the [?/1] button to turn on the main power.
Level SL/SR S XXXXXX 2. Either the message "C.MODE.AV1" or "C.MODE.AV2" ap-
Level CT/SW CW XXXXXX pears. Select the desired mode.
Level SBL/SBR B XXXXXX
USER INITIALIZE
Total power on time OH X 02
Procedure:
Muting Status MUTE XXX 1. Hold the [?/1] for 5 seconds.
Power on counter 2. The message "CLEARING" appears on the display.
REBX. X
(Rebox test mode) 3. After a few seconds, "CLEARED" appears.
Protector Type PROT XXXX
Temperature when protect TEM XXXX
9
STR-DH510
DMPORT MODE
* All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon comple-
tion of repair.
* Procedure:
1. Connect the DMPORT check jig (P/N: J-2501-309-A) with
the DMPORT Jack (J2901) on the MICOM board.
2. While pressing the [TUNING MODE] and [MUSIC] buttons,
press the [?/1] button to turn on the main power.
3. The message "DMPORT T." and "DMPORTOK" appears on
the fluorescent indicator tube and enter the digital media port
test mode. (Confirmation of communication line). When
"NO DET", "UART NG" and "UART TO" are displayed on
the fluorescent indicator tube, confirm the connection of the
DMPORT check jig, and enter the mode again. Each time the
[>] button on the remote commander is pressed, the con-
nect check and adaptor version check are switched. Press the
[.] button on the remote commander, connected confirma-
tion of the DMPORT check jig is done again.
4. To a pin jack of the DMPORT check jig input information
relevant to audio signal (sine-wave 1.0V rms) and composite
video signal (white 100% 1.0Vp-p, color bar, etc).
5. Confirm the output of speakers and monitor TV. (Confirma-
tion of analog signal).
6. To release from this mode, press the [x] button on the remote
commander.
MICOM board
J2901
J001
color DMPORT
pattern check jig TV
generator (Part No.: monitor
J-2501-309-A) set
AF FL/FR
oscillator speaker
MAIN board
TB601
10
STR-DH510
SECTION 3 SECTION 4
FM TUNER CHECK DIAGRAMS
FM AUTO STOP CHECK · Circuit Boards Location
generator
set
OUT (75 )
TEMP-SENSOR board VIDEO STANDBY board
HDMI PC board
POWER KEY board
Procedure: DIGITAL board
1. Turn on the set.
2. Input the following signal from Signal Generator to FM
antenna input directly.
* Carrier Frequency: A=87.5 MHz, B=98 MHz, C=108 MHz HP SUPPORT board
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF) HEADPHONE board
MAIN board
Note: DISPLAY board
Please use 75 ohm "coaxial cable" to connect SG and the set. You CONNECTION board
cannot use video cable for checking.
Please use SG whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confirm that input Frequency of A, B and C are detected and
automatic scanning stops.
The stop of automatic scanning means "The station signal is
received in good condition."
11 11
STR-DH510
4-1. BLOCK DIAGRAM TUNER/AUDIO Section
VIDEO SA-CD/CD TV SAT/CATV VIDEO
AUDIO IN AUDIO IN AUDIO IN AUDIO IN AUDIO OUT
L R L R L R L R L R
-3 -4 -1 -2 -3 -4 -5 -6 DIR -7V +7V -1 -2
J404 (1/2) J402 FUNCTION SELECT J404 (2/2)
IC400
12 8
VEE VCC
48
47
52
51
42 25
41 SEL 26
46 SW
TN1 45
FM/AM TUNER UNIT
76 L-IN DIGITAL
L-CH
R-CH
61
62 R-CH 75 R-IN
A SECTION
FM 75 57
COAXIAL
58
SYSTEM L
ANTENNA 14 FL-CH
SD 63 TUNER_SD CONTROL SEL
AM IC2101 (1/5)
CE 64 TUNER_CE R-CH 13 FR-CH
DI 74 TUNER_MOSI EVOL_DATA 18 10 MCU
EVOL_CLK 19 11 I/F
CLK 75 TUNER_CLK
SL
TU+9V DO 76 TUNER_MISO 18 SL-CH
SEL
POWER KEY
C
R-CH 17 SR-CH
DMPORT_DET 7
SECTION
C
16 C-CH
SEL
SW
15 SW-CH
SEL
KEY/DISPLAY
D
5 DMPORT_RX
DMPORT_TX SECTION
6 DMPORT_TX
DET
7
DMPORT AMP
IC2902
L+ : TUNER (FM/AM)
13 3
J2901 L 1 : VIDEO (AUDIO)
DMPORT 11 2
DC5V
71 70 68 72 69 73 : CD (ANALOG)
R+
0.7A MAX 14 5
R 7
12 6
SW OUT
C OUT
IC2901 (1/2)
DIGITAL SL OUT
2
VBUS+5V
4 +5V REG 2 +6V
SECTION B SR OUT
VIDEO+5V
4 FL OUT
FR OUT
STR-DH510
12 12
STR-DH510
4-2. BLOCK DIAGRAM DIGITAL Section
ADC
IC2401 6CH DAC
IC2601 (1/4) DSP EX3
TUNER/ VINL IC2001 (1/2) IC2501
L-IN 13 DIGITAL
A
AUDIO DOUT
DECIM. 9 2 4 79 DAI_P12 DPSIB
VINR MOD. VO3L
SECTION R-IN 14 FILTER 78 DAI_P11 DPSIA DIN3 25 FL OUT
DPSOA DAI_P6(L&R) 64 9 DAC
VO3R
DSPOC DAI_P8(C&SW) 70 26 R-CH
SWITCH
LRCK
DPSOB DAI_P7(SL&SR) 65
SCKI
IC2014
BCK
6 8 7 1 CK Q 5
TUNER/
8
DIN2
DAC
VO1L
21 SL OUT
B AUDIO
SECTION
9 VO1R
22 R-CH
DIGITAL AUDIO IC2601 (2/4)
INTERFACE RECEIVER 11
IC2801
27 16 VO2L
23 C OUT
XMCK
RMCK
IC2303 DIN1
AUDIO /VO 33 97 FLAG2 NONAUDIO* 7 DAC
J2301 CLKIN 142 VO2R
DVD WAVE RX0 94 DAI_P20 DPFSCK X2001 24 SW OUT
3 SHAPER 2 2 25MHz
IN
RBCK 17 14 12 89 DAI_P19 DPBCK(BCK IN) XTAL 143
(COAXIAL)
RLRCK 20 5 7 88 DAI_P18 DPLRCK(LRCK IN) IC2901 (2/2)
OPTICAL DATA RDATA
RECEIVER INPUT 21 IC2601 (3/4)