Text preview for : AAB-412.pdf part of Aiwa Service XP-V410 mech. DA23L - mod. XP.V411 - XP-V412 (pag. 22)
Back to : AAB-412.pdf | Home
XP-V410 Y1(S) YJ1(LT) AEZ1(L) AHRJ1(S) XP-V411 AEZ1(S) AHRJ1(LT) AK1(S) AEZ1B(G) XP-V412 AEZ1(S) AEZ1B(S)
SERVICE MANUAL
COMPACT DISC PLAYER BASIC CD MECHANISM : DA23L This Service Manual is the "Revision Publishing" and replaces "Simple Manual" (S/M Code No. 09-003-342-6T1). SPECIFICATIONS
RE
S/M Code No. 09-003-342-6R1
DA TA
VI
SIO
N
·
Design and specifications are subject to change without notice .
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
Precaution to replace Optical block (SF-P200)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure.
:SOLDER
16
10 9
1
PICK UP ASSY SF-P200
2
ELECTRICAL MAIN PARTS LIST
REF. NO IC
PART NO.
KANRI NO.
DESCRIPTION
REF. NO C451 C501 C505 C506 C507 C508 C509 C510 C511 C512 C513 C514 C515 C516 C518 C520 C521 C522 C523 C524 C601 C602 C603 C604 C605 C606 C607 C610 C701 C702 C703 C706 C707 C708 C709 C710 C711 C712 C713 C714 C715 C716 C717 C718 C719 C720 C721 C722 C723 CN501 CN601 FB701 FB702 FB703 FB704 J101 J701 L101 L301 L401 L402 L501 L502 L601 LCD101 R115 R116 S301 S302 S303
87-A21-082-040 8A-HCH-602-010 87-A21-446-010 87-A21-568-040 87-A21-578-040 87-A21-543-040 87-A21-521-040 87-A21-085-040 TRANSISTOR 89-211-323-080 87-A30-332-040 87-A30-333-040 87-026-608-080 89-111-625-080 89-416-643-080 89-327-125-080 87-026-680-080 87-026-268-080 87-026-239-080 89-324-121-080 87-026-235-080 DIODE 87-A40-614-040 87-020-591-080 87-A40-554-040 87-A40-469-040 87-020-331-080 87-002-882-080 MAIN C.B C101 C102 C103 C105 C106 C107 C108 C109 C110 C111 C112 C113 C301 C302 C303 C304 C305 C306 C307 C308 C309 C401 C403 C406 C407 C408 C409 C410 C412 C414 C417 C418 C419 87-010-060-040 87-010-197-080 87-010-197-080 87-012-156-080 87-010-483-040 87-010-194-080 87-010-178-080 87-A12-158-040 87-012-141-080 87-A10-505-080 87-010-805-080 87-010-196-080 87-A10-488-040 87-010-197-080 87-010-196-080 87-010-196-080 87-010-197-080 87-010-197-080 87-010-197-080 87-010-309-080 87-010-196-080 87-016-557-040 87-015-677-040 87-A11-550-080 87-010-198-080 87-016-460-080 87-016-526-080 87-010-197-080 87-A12-158-040 87-010-318-080 87-010-318-080 87-010-146-080 87-010-146-080
C-IC,BA6655AFV C-IC,MN101C439-XXX C-IC,MN662782RPT1 C-IC,GLT441M04 C-IC,AN8838NSB C-IC,NJU7012 C-IC,BH6517FS C-IC,TA2120FN
KANRI DESCRIPTION NO. 87-010-196-080 CHIP CAPACITOR,0.1-25 87-A12-158-040 CAP,E 100-4 M 7L SRA 87-012-365-080 C-CAP,S 0.027-25VBK 87-012-156-080 C-CAP,S 220P-50 CH 87-010-321-080 CHIP CAPACITOR,82P(J) 87-010-321-080 87-A11-550-080 87-A12-158-040 87-010-196-080 87-A10-488-040 87-010-196-080 87-012-365-080 87-012-365-080 87-010-196-080 87-010-312-080 87-A10-488-040 87-012-349-080 87-010-805-080 87-010-805-080 87-010-154-080 87-A12-158-040 87-010-197-080 87-010-805-080 87-010-197-080 87-010-196-080 87-010-196-080 87-010-197-080 87-010-805-080 87-A12-158-040 87-010-854-080 87-010-854-080 87-012-368-080 87-A10-826-080 87-A10-826-080 87-A10-826-080 87-015-681-040 87-A10-488-040 87-012-141-080 87-012-368-080 87-015-696-040 87-015-681-040 87-012-368-080 87-012-368-080 87-010-483-040 87-010-483-040 87-010-178-080 87-010-178-080 87-012-368-080 87-010-197-080 87-A61-104-010 87-009-411-010 83-XM1-617-080 83-XM1-617-080 83-XM1-617-080 83-XM1-617-080 87-A60-421-010 85-HC5-616-010 87-005-770-080 87-A50-367-080 87-A50-556-080 87-A50-440-080 87-A50-367-080 87-A50-367-080 87-A50-580-080 8A-HC7-602-010 87-022-525-080 87-022-355-080 87-A90-163-010 87-A91-742-010 87-A91-622-010 CHIP CAPACITOR,82P(J) C-CAP,S 820P-50 K B CAP,E 100-4 M 7L SRA CHIP CAPACITOR,0.1-25 CAP,E 47-4 7L SR CHIP CAPACITOR,0.1-25 C-CAP,S 0.027-25VBK C-CAP,S 0.027-25VBK CHIP CAPACITOR,0.1-25 C-CAP,S 15P-50 CH CAP,E 47-4 7L SR C-CAP,S 1000P-50 CH CAP, S 1-16 CAP, S 1-16 CAP CHIP 10P CAP,E 100-4 M 7L SRA CAP, CHIP 0.01 DM CAP, S 1-16 CAP, CHIP 0.01 DM CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP, CHIP 0.01 DM CAP, S 1-16 CAP,E 100-4 M 7L SRA C-CAP,S 560PCH C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 560PCH 0.1-50 1-10 K 1-10 K 1-10 K F B B B
PART NO.
C-TR,2SB1132R C-TR,CPH3106 C-TR,CPH3206 C-TR,DTC 123 JK TR,2SA1162 (0.15W) C-TR,2SD1664R CHIP TR,2SC2712GR C-TR,IMH4A C-TR,RN2411 TR,DTC114TK (0.2W) C-TR,2SC2412K CHIP-TR,DTC114EK
C-DIODE,SFPB-72 C-ZENER,02CZ 11Y C-DIODE,RB491D C-DIODE,HSM2838CTR CHIP-DIODE,DAN202K C-DIODE,RB425D
CAP,E 100-16 CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM C-CAP,S 220P-50 CH CAP,E 220-4 7L SRA CAP, CHIP 0.047 CHIP CAP 1000P CAP,E 100-4 M 7L SRA CHIP-CAPACITOR,0.22-16F CAP,E 220-6.3 SF CAP, S 1-16 CHIP CAPACITOR,0.1-25 CAP,E 47-4 7L SR CAP, CHIP 0.01 DM CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM C-CAP,1000P-50 CH CHIP CAPACITOR,0.1-25 CAP,E 100-6.3 SF CAP,E 100-6.3 7L C-CAP,S 820P-50 K B CAP, CHIP 0.022 C-CAP,S 0.22-16 B C-CAP,S 0.47-16 BK CAP, CHIP 0.01 DM CAP,E 100-4 M 7L SRA C-CAP,S 47P-50 CH C-CAP,S 47P-50 CH CHIP CAP 2PF CHIP CAP 2PF
E/CAP 10-16 CAP,E 47-4 7L SR CHIP-CAPACITOR,0.22-16F C-CAP,S 0.1-50 F CAP,E 2.2-50 SRA E/CAP 10-16 C-CAP,S 0.1-50 C-CAP,S 0.1-50 CAP,E 220-4 7L CAP,E 220-4 7L F F SRA SRA
CHIP CAP 1000P CHIP CAP 1000P C-CAP,S 0.1-50 F CAP, CHIP 0.01 DM CONN,16P H WHITE 52089-1610 CONN,6P ZH V C-COIL,BK2125HM601 C-COIL,BK2125HM601 C-COIL,BK2125HM601 C-COIL,BK2125HM601 JACK,DC HEC3600 BLK 6 JACK,3.5 ST W/R GRN COIL,47UH 7607 C-COIL, 10UH LQG21F C-COIL, 47UH K LQH3C C-COIL, 100UH K LQH3C34 C-COIL, 10UH LQG21F C-COIL, 10UH LQG21F COIL,470UH LHL06NB LCD,AHC-7 C-RES,S 20K-1/10W F C-RES,S10K-1/10W F SW,SL1-1-2 HSW1060 SW,SL 4-1-3 HSW2061-010010 SW,MICRO PV1102
3
REF. NO S304 S305 S306 S307 S308 S309 VR701 X401
KANRI NO. 87-A90-095-080 SW,TACT 87-A90-095-080 SW,TACT 87-A90-095-080 SW,TACT 87-A90-095-080 SW,TACT 87-A90-095-080 SW,TACT 87-A90-095-080 87-A90-462-010 87-A70-202-080
PART NO.
DESCRIPTION EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M EVQ11G04M
SW,TACT EVQ11G04M VR,RTRY 30KCX2 H RK14J12A0 C-VIB,CER 16.93MHZ CSACV-MXJ04
· Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Resistor Code Value of resistor Chip resistor
Dimensions (mm)
Figure
Wattage 1/16W 1/16W 1/10W 1/8W
Type 1005 1608 2125 3216
Tolerance 5% 5% 5% 5%
Symbol CJ CJ CJ CJ
Form
L W
L 1.0
t
W 0.5 0.8 1.25 1.6
t 0.35 0.45 0.45 0.55
:A Resistor Code : A
104 108 118 128
1.6 2 3.2
4
TRANSISTOR ILLUSTRATION
C B E E1 B1
C1
B2
E2
C2
B C E
2SA1162 2SC2412 2SC2712 CPH3106 CPH3206 DTC114EK DTC114TK DTC123JK RN2411
IMH4A
2SB1132 2SD1664
5
LCD DISPLAY LCD, AHC-7
6
SCHEMATIC DIAGRAM
FB701 BK2125HM601
FB704 BK2125HM601
HSM2838CTR
7
8
WIRING-1 (MAIN :COMPONENT SIDE)
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
9
10
WIRING-2 (MAIN :CONDUCTOR SIDE)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
E
F
G
H
I
J
11
12
TEST MODE
The servo circuit of this model is designed to be adjustment-free and the adjustment value and disc distinction (CD-DA, CD-R and CDRW) etc. is adjusted by the IC. Therefore the adjustment is performed at each TOC reading. The adjustment conditions in the IC of each servo can be monitored in this test mode.
1. How To Start The Mode
OPEN/CLOSE SW SHORT LAND VC
Starting method of the test mode differ depending upon the type of disc being used. This is because the adjustment values of each servo also differ depending upon the type of disc. When using the CD-DA or CD-R 1) Short-circuit TEST LAND and OPEN/CLOSE SW land. 2) Insert the AC plug to the power outlet and install the CD-DA or CD-R disc. 3) Press the PLAY and STOP buttons in this sequence and read the TOC.
TE
S303
FE
IC502
When using the CD-RW 1) Short-circuit the TEST LAND and OPEN/CLOSE SW land. 2) Insert the AC plug to the power outlet and install the CD-RW disc. 3) Press the PLAY, STOP and DSL buttons in this sequence and read the TOC. The LCD should display "CD-r" at this point. Note 1: If the TOC cannot be read, "ERR" has appeared on the LCD. The following step 2 and 3 can be verified even if the "TOC" cannot be read. Note 2: By repeatedly pressing the DISPLAY/ENTER button all the LCDs light up and the "TOC" display is repeated. Note 3: By repeatedly pressing the DSL button the LCD "CD-r" and "CD-d" are repeated.
20 7 IC401
IC501
RF
When the LCD displays "CD-d" TMCD-DA, CD-R is selected. When the LCD displays "CD-r" TMCD-RW is selected. Note 4: The test mode is canceled by disconnecting the AC plug and remove the soldering of short land.
2. DISC distinction (confirmation of the FE waveform)
IC451
IC601
This mode enables you to perform a confirmation of the disc distinction. Confirmation method Press the DSL button and select "CD-d" or "CD-r" (Refer to Note 3). 1) Install the disc. 2) Press the MODE button. The LCD will change as follows: Example: Test disc: TCD-782, DISC type select: CD-d Judgment value: 68, Measurement value: 37 CF
IC701
68
61 IC301
37 CF
Measurement value
LCD displays "CD-d" LCD displays "CD-r" No disc No disc CD-RW CD-DA and CD-R
Judgment value
* All numerical values are displayed in HEX. What disc the IC has selected can be understood according to the judgment value. The decision standard of IC is as follows.
0 < Judgment value < 10
No disc CD-RW CD-DA and CD-R
TEST MODE SHORT LAND
10 < Judgment value < 32 32 < Judgment value < C8 C8 < Judgment value
The state of the FE waveform can be also understood from this judgment.
13
14
3. Confirmation of Sled movement
By pressing the F.SKIP or B.SKIP button continuously during the TEST MODE, it is possible to transfer the pick-up to either the outer side or inner side.
4. Confirmation of the RF level
Test point: RF and VC (Vref) Test disc: TCD-782 Confirm that the RF waveform is as shown below.
0.8Vp-p or more
VOLT/DIV: 200mV TIME/DIV: 0.5us
5. Confirmation of Tracking balance
Test point: TE and VC (Vref) Test disc: TCD-782 Press the DSL button while playing the test disc and confirm the TE waveform is as shown below.
A VC B
VOLT/DIV: 200mV TIME/DIV: 2ms
A:B=1:1
6. Confirmation of each servo
It is possible to confirm the adjustment value of each servo by repeatedly pressing the MODE button while the disc is playing. The switchover sequence is as stated below. Confirmation mode off TM Focus Bias (FB) TM Tracking Balance (TB) TM Tracking Gain (TG) TM Tracking Error Offset (TEO) TM Focus Gain (FG) TM Focus Error Offset (FEO) TM Confirmation mode off Example: Tracking Error Offset (TEO) Adjustment value: 03
te 0
Tracking Error Offset (TEO) display
* Adjustment value is displayed in HEX.
:03
Adjustment value
15
WAVE FORM
1
IC501 Pin 7
VOLT/DIV: 0.5V TIME/DIV: 1µS
5
IC401 Pin
71
VOLT/DIV: 2V TIME/DIV: 5µS f=44.1kHz
2
IC501 Pin
VOLT/DIV: 0.2V TIME/DIV: 50µS
6
IC401 Pin TM
VOLT/DIV: 1V TIME/DIV: 5µS
3
IC501 Pin §
VOLT/DIV: 0.1V TIME/DIV: 2mS
4
IC401 Pin
78
VOLT/DIV: 1V TIME/DIV: 50mS f=16.93MHz
16
IC, GLT441MV4
power off Ref.vol Vref2 Regulator Starter Ref.vol Vref1 BST Starter Normal
IC BLOCK DIAGRAM IC, BA6655AFV
Power switch 1
Power switch 2
Switching driver
ST PULSE
17
DET DET DET
IC, BH6517FS
IC, AN8838NSB
OP
OP
IC DESCRIPTION IC, MN662872RPT1
Pin No. 1 2 3 4 5 6 7 8 9 10-16 17-19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Pin Name DVDD3V D0 D1 NWE NRAS D2 D3 NCAS0 NCAS1 A8-A0 A1-A3 DVSS2 DVDD2 SPOUT TRVM TRVP TRM TRP FOM FOP FBAL TBAL VREF FE TE RFENV OFT NRFDET BDO LDON ARF IREF ADPVCC DSLF DSLF2 PLLF VCOF AVDD2 AVSS2 OUTL I/O I I/O I/O O O I/O I/O O O O O I I O O O O O O O O O I I I I I I I O I I I O O O O I I O Description Power supply for DRAM interface. (pin No. 2 to 19). DRAM data input/output signal 0. DRAM data input/output signal 1. DRAM write enable signal. DRAM RAS control signal. DRAM data input/output signal 2. DRAM data input/output signal 3. DRAM CAS control signal 0. DRAM CAS control signal 1. (when both 1 M and 4 MDRAM are used). DRAM address signal 10. (when 16 MDRAM is used). DRAM address signal 8-0. DRAM address signal 1-3. Ground for digital circuit. Power supply for digital circuit. Spindle motor drive signal output. (absolute value output). Traverse drive output. (positive polarity output). Traverse drive output. (negative polarity output). Tracking drive output. (positive polarity output). Tracking drive output. (negative polarity output). Focus drive output. (positive polarity output). Focus drive output. (negative polarity output). Focus balance adjustment output. Tracking balance adjustment output. DA output block reference voltage. (FBAL, TBAL, DSLF2). Focus error signal input. (analog input). Tracking error signal input. (analog input). RF envelope signal input. (analog input). Off-track signal input. H: Off-track. RF detection signal input. L: Detection. Drop-out signal input. H: Drop-out. Laser ON signal output. H: ON. RF signal input. Reference current input terminal. AD reference voltage input. (analog input). Loop filter terminal for DSL. For DSL unbalance current correction. Loop filter terminal for PLL. Loop filter terminal for jitter free VCO. Power supply for analog circuit. (for DSL, PLL, VCOF, AD, DA). Ground for analog circuit. (for DSL, PLL, VCOF, AD, DA). Lch audio output. (Refer to (Note 1) on page 3).
18
Pin No. 49 50 51 52 53 54 55 56
Pin Name AVSS1 OUTR AVDD1 FSEL TMOD1 TMOD2 FLAG CLVS/IPFLAG
I/O I O I I I I O O
Description Ground for analog circuit. (for audio output block). Rch audio output. (Refer to (Note 1) on page 3). Power supply for analog circuit (for audio output block). Noise filter ON/OFF switching input. L: ON. H: OFF. Terminal mode select input terminal 1. Normal: L. Terminal mode select input terminal 2. Normal: L. Flag signal output. Command selection. · Spindle servo phase sync signal output. H: CLV. L: Rough servo. · Interpolation flag signal output.H: Interpolation.
57
EXT0/ISRDATA
I/O
Command selection.
· Extended input/output port 0. · SRDATA input.
58
EXT1/ILRCK
I/O
Command selection.
· Extended input/output port 1. · LRCK input. H: Lch audio data. L: Rch audio data.
59 60 61 62 63 64
EXT2/IBCLK TX MCLK MDATA MLD BLKCK
I/O O I I I O
Command selection.
· Extended input/output port 2. · BCLK input.
Digital audio interface output signal. Microprocessor command clock signal input. (Latches data at raising edge.) Microprocessor command data signal input. Microprocessor command load signal input. L: Load. Sub-code block clock signal. fBLKCK=75 Hz (during normal playback)/SYNC signal for CDTEXT (DQSY) fDQSY=300 Hz (during normal playback).
65
SQCK/BCLK
I/O
Command selection.
· External clock input for sub-code Q register. · Bit clock output for SRDATA.
66
SUBQ/LRCK
O
Command selection.
· Sub-code Q data output. · L, R identification signal output. H: Lch audio data. L: Rch audio data.
67
DMUTE/SRDATA
I/O
Command selection.
· Muting input. H: Mute. · Serial data output. (Refer to (Note 1) of page 3.)
68 69 70 71 72 73
STAT NRST SPPOL PMCK SMCK SUBC/SSYNC
O I O O O O
Status signal. (CRC, RESY, CLVS, NTTSTOP, SQOK, FLAG6, SENSE, NFLOCK, NTLOCK, BSSEL, SUBQ data, CDTEXT data, anti-shock read-out data) Reset input. L: Reset. Spindle motor drive signal output (polarity output). 88.2 KHz clock signal output. 4.2336 MHz clock signal output. Command selection. · Sub-code serial output. · Sector SYNC output.
74 75 76 77 78 79 80
SBCK/64FS NCLDCK NTEST X1 X2 DVDD1 DVSS1
I O I I O I I
Command selection.
· Clock input for sub-code serial output. · 64 FS output.
Sub-code frame clock signal output. (fCLDCK=7.35 KHz) Test terminal: Normally H. Crystal oscillator circuit input terminal. f=16.9344 MHz. Crystal oscillator circuit output terminal. f=16.9344 MHz. Power supply for digital circuit. Ground for digital circuit. 19
IC, MN101C439-AD
Pin No. 1-4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Pin Name COM3-0 VLC3 VLC2 VLC1 VDD OSC2 OSC1 VSS XI XO MMOD VREFK-FUNC K-P/S ACIN VDIN K-RMC SWDO SWEASS SWR/H VREF+ SWIL PC CD-RW
______________
I/O O -- -- -- -- O I -- I O I -- I I I I I I I I -- I O O O I O O -- O I O O O I I I -- O O O LCD common. -- -- -- LCD power supply.
Description
Microprocessor main clock oscillator output. Microprocessor main clock oscillator input. Ground. Sub-clock oscillator input. Sub-clock oscillator output. Processor mode is not used. Connected to VSS. VSS. Function key input. PLAY, STOP KEY input. AC adapter detection. Battery voltage detection. Wired remote control input. Digital out ON/OFF input. L= ON. Select input of EASS mode. Refer to A/D value table. Resume/hold switch input. VCC. Limit switch input. Power off output of CD servo driver. L= Power off. CD-RW playback gain-up select output. H= Gain-up. CD-RW playback gain-up select output. L= Gain-up. H/A power-down output. Gain-up select output by EASS. During EASS ON= L. Buzzer output of headphones. Microprocessor reset input. DSP reset output. STAT input of DSP. MLD output of DSP. MDATA output of DSP. MCLK output of DSP. BLKCK input of DSP. Wireless remote control sensor signal input. Select input of AHC-4 or AHC-5. AHC-4=H. AHC-5=L. Not used. Power down output of H/A. Select output of gain-up by EASS. During EASS ON= L. DSL2 control output of headphones. DSL2= H. DSL1/OFF= L.
CD-RW SUBQ SQCK BEEP RST NRST STAT MLD MDATA MCLK BLKCK RSENSOR AHC-4/5 --
_____________
PU-ON
________________
EASSON DSL2
20
Pin No. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64-79 80
Pin Name DSL1 MUTE STANDBY LCDRDO P-OFF DSCHRG CHRG BAT-F BAT-M BAT-E 2.5V SWCL ELON SPCON CAR_LED E-MODE TEST M1/NM2 NC SEG15-0 NC
I/O O O O O O O O O O O O O O O O I I I -- -- --
Description DSL ON control output of headphones. DSL ON= H. Audio mute output. Standby output of headphones. During standby =L. Power on= H. Wired LCD remote control output. Power-off output of power supply IC. L= Power off. Discharge output. Charge output. Full indication LED output of battery remaining amount display. L= LED ON. Medium indication LED output of battery remaining amount display. L= LED ON. Empty indication LED output of battery remaining amount display. L= LED ON. Not used. Open/close detection switch input of lid. EL backlight control output. Spindle PWM control output. Outputs to light button LED of CAR-KIT model. H= Lights. Spindle-loss mode. (H= There is no spindle-loss mode). L= Enters TEST mode. Input to select either 10 seconds or 10/40 seconds by AHC-5. H= 10 seconds. L= 10/ 40 seconds. Not used. LCD segment output. Not used.
21
MECHANICAL EXPLODED VIEW 1/1
8
9
8 10 DA23L 8
11
12 LCD KEY, SKIP
7 5 A 6
KEY, PLAY HLDR, KEY R HLDR, KEY L C 14 P.C.B 4
a
C
13
3
2
15
a
KEY, JOINT
B 1 LID,BAT C
22
MECHANICAL PARTS LIST 1/1
REF. NO 1 2 2 2 3 4 5 6 7 8
KANRI DESCRIPTION NO. 88-HC6-021-010 FOOT, DIA10 8A-HCH-014-010 CABI ASSY,BOTTOM 17 8A-HCH-056-010 CABI ASSY,BOTTOM 17 (LT)<0YJ1LT> 8A-HCH-032-010 CABI ASSY,BOTTOM 17 LL <2AEZ1BG,1AEZ1L,1AHRJLT> 87-HC8-205-010 BAT-CONTACT,(+)(-) 8A-HC7-012-010 8A-HC7-201-010 8A-HC7-202-010 8Z-HC7-205-010 8Z-HC1-225-010 KNOB,SL HOLD GUIDE,LCD BAT-CONTACT,(+) BAT-CONTACT,(-) DMPR,MECHA(SP) WINDOW,CD<1AHRJ1S,2AEZ1BS> WINDOW,CD (L) <2AEZ1BG,1AEZ1L,1AHRJLT,0YJ1LT> WINDOW,CD 17 <2AK1S,0Y1S,1AEZ1S,2AEZ1S> WINDOW,DISPLAY LID ASSY,CD 17 (G)<2AEZ1BG>
PART NO.
REF. NO
KANRI DESCRIPTION NO. 11 8A-HCH-045-010 LID ASSY,CD 17 (L) <1AEZ1L,1AHRJLT> 11 8A-HCH-044-010 LID ASSY,CD 17 (LT)<0YJ1LT> 11 8A-HCH-015-010 LID ASSY,CD 410<0Y1S> 11 8A-HCH-016-010 LID ASSY,CD 411<1AHRJ1S,1AEZ1S> 11 8A-HCH-017-010 LID ASSY,CD 412 <2AK1S,2AEZ1S,2AEZ1BS> 12 85-HC6-205-110 SHAFT,LID(300) HK 13 8A-HC7-204-010 SPR-T,OPEN 14 8A-HCH-013-010 CABI ASSY,CENTER 17 14 8A-HCH-055-010 CABI ASSY,CENTER 17 (G)<2AEZ1BG> 14 8A-HCH-054-010 CABI ASSY,CENTER 17 (L) <1AEZ1L,1AHRJLT> 14 15 A B C 8A-HCH-053-010 8A-HC7-018-010 87-067-868-010 87-067-869-010 87-067-384-010 CABI ASSY,CENTER 17 (LT)<0YJ1LT> LEVER,OPEN V+1.7-4 HL BLK V+1.7-8 HL BLK SCREWVT1.4-3.5HL <2AK1S,0Y1S,1AEZ1S,2AEZ1S>
PART NO.
9 8A-HC7-007-010 9 8A-HC7-079-010 9 8A-HCH-004-010 10 8A-HC7-005-010 11 8A-HCH-047-010
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange
23
CD MECHANISM EXPLODED VIEW 1/1
D
D 2
4
9 A 3
5
1
7 8 C 6
10 B
24
CD MECHANISM PARTS LIST 1/1
REF. NO 1 2 3 4 5 6 7 8 9 10 A B C D
KANRI DESCRIPTION NO. S0-A41-A20-600 PICKUP LASER ASSY SM-10A-108-001 MOTOR ASSY SPINDLE S0-M10-A10-900 MOTOR SLED ASSY S2-311-A12-200 CHASSIS S2-511-A23-200 GEAR MIDDLE S2-511-A23-100 S2-511-A23-400 S2-511-A07-900 S4-S13-A00-200 S2-451-A18-100 SS-EXE-A04-000 SS-GXE-A00-300 SS-EXE-A14-100 SS-GXE-A00-202 GEAR,SCREW GEAR,RACK SPINDLE SCREW SW,LEAF HOLDER GEAR SCR PAN SPECIAL SPECIAL SPECIAL PCS 1.4-2.2 SCREW SCREW SCREW M1.7-4.0
PART NO.
ACCESSORIES/PACKAGE LIST
REF. NO 1 1 1 1 1 1 1 1 1 1 ! ! ! 1 2 2 2 3
PART NO. 8A-HCH-915-010 8A-HCH-925-010 8A-HCH-917-010 8A-HCH-927-010 8A-HCH-916-010 8A-HCH-926-010 8A-HCH-912-010 8A-HCH-935-010 8A-HCH-937-010 8A-HCH-936-010 8A-HCH-922-010 87-B30-283-010 87-B30-285-010 87-B30-284-010 87-B30-259-010
KANRI NO.
DESCRIPTION
IB,EZ(EGF)C 411 F<1AEZ1L,1AEZ1S> IB,EZ(EGF)C 412 F<2AK1S,2AEZ1BG,2AEZ1S,2AEZ1BS> IB,EZ(PHNCZ)C 411 F<1AEZ1L,1AEZ1S> IB,EZ(PHNCZ)C 412 F<2AEZ1BG,2AEZ1S,2AEZ1BS> IB,EZ(SID)C 411 F<1AEZ1L,1AEZ1S> IB,EZ(SID)C 412 F<2AEZ1BG,2AEZ1S,2AEZ1BS> IB,HR(ECA)C F<1AHRJ1S,1AHRJLT> IB,Y(EGF)C 410 F<0Y1S> IB,Y(PHNCZ)C 410 F<0Y1S> IB,Y(SID)C 410 F<0Y1S> IB,YJ(ECA)C 410 F<0YJ1LT> AC ADAPTOR,AC-D603ENC<2AEZ1BG,1AEZ1L,1AEZ1S,2AEZ1S,2AEZ1BS> AC ADAPTOR,AC-D603HRNC<1AHRJ1S,1AHRJLT> AC ADAPTOR,AC-D603KNC<2AK1S> HEADPHONE,HP-M032(T) L<0YJ1LT> HEADPHONE,HP-M048 PLUG,CONVERSION WTN-1157R1<1AHRJ1S,1AHRJLT> BAT,NB-301 NC(2PCS)<2AK1S,2AEZ1BG,2AEZ1S,2AEZ1BS>
!
3 87-B30-326-010 5 87-A90-312-010 6 87-B30-141-010
25
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
737004 Printed in Singapore