Text preview for : 206087.pdf part of Sharper Image Quad Smart Drone User Guide for the quad copter drone with camera.
Back to : 206087.pdf | Home
1.CONTROLLER COMPONENTS: 3.INSTALL THE PROTECTOR : 7.SETTING UP THE SIGNAL CONNECTION:
Push the protector into the Bottom of the motor base as Pic.1. Press the Lock of the protector to locking together
as Pic.2, the protector is installed finish.
No Function Power switch Speed Button
Flip Button
Up/Down and
Quad Smart Drone Turn Left/Turn Forward/Backward and
Item No. 206087 Right Lever Leftside/Rightside Lever
Pull
Headless mode Forward and backward
User's Guide Finish
Trim Button
one-button start Pic.1 Pic.2 Pic.3
Bank Left/Bank right
Trim Button 5.CHARGING YOUR DRONE BATTERY:
take off/landing Inset the battery to the battery housing. (see frist picture). Turn on the power switch of the Drone - the LED's
BATTERY WARNING: on the Drone will start to flash. Place the Drone down on a flat surface, making sure the drone is facing
Lithium Polymer batteries can expand, burst or catch fire if used incorrectly, causing both property damage and away from you.
or personal injury. It is essential that you follow all the included instructions and safety warnings in full. The
manufacturer, distributors and retailers will assume no liability for the failure to comply with these safety
instructions and warnings.
INSTRUCTIONS WHEN CHARGING:
1) The battery must be removed from the product before charging.
2.SETTING UP THE CONTROLLER / DRONE: 2) If the battery has just been used, please let it cool down to room temperature before charging.
Turn on the controller Power Switch, The controller will make 4 short
3 X AAA(LR06) 3) Charging must only be undertaken by an Adult, and only using the charger included with this product. BEEP sounds and the red LED will flash. To pair the signals of the Drone
INSTALLING THE CONTROLLER BATTERIES 1.5V Batteries 4) Always charge the battery on a non flammable heat resistent surface with non flammable surroundings. and the Controller, you must RAISE the UP/DOWN Lever on the controller
5) Connect the battery to the USB charging cable all the way to the TOP. And then LOWER it all the way to the BOTTOM,
It will make one short BEEP sound. And the LED of drone will being
1. Unscrew the battery cover, and insert 3 *AAA batteries, 6) Connect the USB Charging cable to your USB Charging devices. The RED LED on the USB will Trun Off constant light, indicated the signals pair is beening finished.
making sure you insert them following the correct while charging, and will Turn On once the battery is fully charged. It takes around 45 minutes to fully
polarity as shown. charge the battery. Never continue to charge the battery after the RED LED have Turned On.
2. Re-attach the battery cover
NOTICE:
1. Always have an adult to install the batteries
2. Always use Alkaline Batteries
3. Never mix old and new batteries
Always Trun off the Power Switch of the Drone after flight.
Battery Cover
Please read these instructions carefully
and store for future reference.
7) Lithium Polymer batteries do not last forever. If your battery becomes damaged in a crash or no longer charges
properly, immediately replace it with a new battery. To prolong the life of your battery, it is always best to retain
a bit of charge in your battery prior to charging it. Always turn the controller off after flight, and remove all batteries
if leaving un-used for a long period of time.
Remark: Only USB charging cable that inside packaging can be used for charging.
WARRANTY AND CUSTOMER SERVICE 6.SAFE FLIGHT ENVIRONMENT:
Sharper Image branded drones purchased from
SharperImage.com include a 60-day limited replacement 1. Make sure the surrounding area is free of all people, pets or other obstacles before you start to fly.
2. The Drone is designed for Outside flying, or Indoors if you have enough space.
warranty. For customer service, please call 1 (877) 210-3449.
Do not use in strong wind.
3. Leave 1.5 meters between you and the Drone at all times.
1 2 3
12.FLIGHT ADJUSTMENT SECTION: 14.HEADLESS FUNCTION: 4.FUNCTIONAL SPECIFICATIONS
2. Take off the Drone: Pull-down the Left
When you lift your Drone into the air, and don't use any of the other direction levers, your Drone Headless function: Press "OFF" button, it will change to "ON" , will enter the Smartphone control mode: and the Right Lever at the same time to
should simply hover in one spot without moving in any other direction. If however it doesn't, you can follow the Press the Headless Button once, you will
bellow instructions to TRIM your Drone back to a perfect hover. unlocks the Drone, then the motors will
get into Headless mode flying, the LED
of drone will flash and the controller will
start spinning.
make "Beep Beep..." sound. To quit from Raise the Left Lever, the drone will taking
Headless mode by Press the same button. off. Or press the One-key Take off Button,
If your Drone banks to the Left, the drone will automatically goes up to
keep pressing the Bank Left/Bank Right air and stays at a height of around 1.5
Trim Button to the Right till the meters
Drone stops banking.
3. Ascending/Descending: Raise the Left Lever to raise the drone, and back towards
to lower it. Once you lift it to a certain height you like, release the Lever, then the Left
lever will be back to the middle and the drone will hold at this height.
4. Turning Left/Right: Push left on the Left Lever to rotate the drone to the left and
If your Drone banks to the Right, 16.EXTRA INSTRUCTION MANUAL FOR WIFI CAMERA DRONE FUNCTION: right to rotate to the right.
keep pressing the Bank Left/Bank Right 5. Joystick Mode: Push left on the Right Lever to bank the drone left and right to bank
Trim Button to the Left till the 1.INSERT THE SMARTPHONE
Drone stops banking.
it right. Push forward on the Right Lever to move he drone forward and push the lever
Pull out the accessory as . Push-in the smartphone holder, put the smartphone inside
As below pictures). back towards you to move the drone backwards.
6. Gravity sensor mode: Press the Gravity sensor mode button to enter the Gravity
sensor mode, The button will turn to . You only need tilt the smartphone in the
desired direction for the drone flies forward, backward, bank left and bank right.
If your Drone flies Backwards, 7. Landing the Drone: When the drone flying in the sky, press the Landing Button
keep pressing the Forward/Backwards once, the LED light of drone will flash, and the drone will slowly descend to floor
Trim Button Up till the
Drone stops flying Backwards.
and landing, the motors will stop spinning. Or Push the Left Lever to fully backward
position and hold for 3 seconds, the Drone will landing and motors stop spinning.
If your Drone flies Forwards, 2.SOFTWARE DOWNLOAD AND INSTALLATION
keep pressing the Forward/Backwards
Trim Button Down till the
Drone stops flying Forwards.
13.AUTO TRIM FUNCTION: Google play 360 IOS One-key Take off
3.USING INSTRUCTION One-key Landing
Push both controll levers to the positions shown in the picture, 1). Connect the model to the power, the indicator on camera light up .
and hold them for one second. The lights on the drone will start 2). Enter the "setting" menu of your mobile device and turn on WIFI.
to flash. Now the quadcopter is recovered to its original 3). Find a network WIFI called "WIFI UFO" ,click connection until "connected".
factory setting and ready to fly again. 4). Open the "WIFI UFO" software, click the "play" icon into the control interface.
And you will see the real time video. 5.HOW TO CONTRAL BY SMARTPHONE
1. Pair the signal: Trun on the drone, open the phone Settings interface, search the
WIFI signal "WiFiUFO - xxxxxx" From the drone and connect the WIFI. Enter the
control interface of APP, Press "OFF" button to enter the Smartphone control mode,
it start to pair the signal between the drone and the smartphone. You must waiting The SHARPER IMAGEŽ name and logo are registered trademarks.
WiFi UFO for 3 seconds, the LED on the drone will be flashing while paring the signal. Once ŠSharper Image. All Rights Reserved.
it becomes constant lights, the Signal connection is completed.
5 6 7 8