Text preview for : 9227CB-TE.pdf part of MAKITA 9227CB-TE MAKITA 9227CB-TE.pdf
Back to : 9227CB-TE.pdf | Home
T ECHNICAL INFORMATION
Models No. 9227CB
New Tool
Description 180mm Sander Polisher
CONCEPTION AND MAIN APPLICATIONS 470
Model 9227CB is the improved version of the existing Model
(18-1/2")
9217SPC and its brief benefits are;
*Easy for polishing
Variable speed control by trigger : 0-3000rpm
Variable speed control by dial : 600-3000rpm(wide area)
*Loop handle can be gripped easily at various operating
position.
*Face of pad is velcro type to make replacing buff (wool
pad, etc.) easy.
*Sanding operation can be performed using rubber pad and
abrasive disc (optional accessories).
(7-5/8")
194
*Electronic speed control feature
Less reaction at starting by soft start feature
Clean surface by steady speed feature
Specifications
Continuous Rating(W)
Voltage (V) Current (A) Cycle (Hz) Max. Output(W)
Input Output
110 10.0 50/60 1100 580 1600 For U.K.
220 5.7 50/60 1200 710 1800
230 5.5 50/60 1200 710 1800
240 5.3 50/60 1200 710 1800
240 4.8 50/60 1100 580 1800 for U.K.
No Load Speed 0-3000rpm
Diameter of wool pad 180mm (7")
Net Weight 3.0kg (6.6 lbs)
Cord Length 2.5m (8.2 ft)
Standard equipment
Hex. Wrench 6--------1 pc.
Wool Pad 180---------1 pc.
Sleeve 18---------------1 pc.
The standard equipment may differ from country to country.
Optional accessories
Abrasive Disc 180-16,20,24,30,50,80,100,120
Rubber Pad
Sanding Lock Nut 16-48
Lock Nut Wrench 28
Grip 36 Complete
Wool Pad 180 Set
Wool Bonnet 180
Features and benefits
1.Double insulated
2.See the sheets attached for more information.
The standard equipment for the tools shown may differ form country to country.
Variable speed control by dial
600~3000rpm(wide area)
600rpm is fit to wax urethane bumper.
Loop handle
Easy to grip at
various operating position
*Grip 36 Complete Dial can be actuated
(optional accessory) during operation
can be attached.
Cord guard is angled upward
Power supply cord is easy to
be hung on the shoulder and
is not trailed on the work.
Button for
locking spindle
Variable speed control by trigger
Speed can be controlled up to the
Face of pad is velcro type speed set by dial.
Convenient for operation requiring
Eassy to replace buff (wool pad,etc.)
very low speed.
Pad can be replaced without tool
because pad and lock nut are
molded in one piece.
Rubber pad (optional accessory)
can be attached with lock nut
(optional accessory)
Repair
(1) Replacing of armature
1) Remove the magic pad.
2) Remove the carbon brush.
3) Remove the tapping screw PT4x18 for
holding the handle. Carbon brush
Brush holder Tapping screw
PY 4x18(4 pieces)
4) Disconnect the E ring from the armature shaft and then remove the magnet sleeve.
5) Disconnect one body of gear housing and armature from the motor housing.
6) Remove the tapping screw CT 4x16 for holding the bearing box.
7) Remove the pan head screws M5 x 12 and M5 x 16 for holding the bearing retainer and then pull out the
armature.
8) To assemble the armature on the gear housing, make fit the guide of bearing retainer of gear housing on the
protrusion of the bearing retainer before assembling.
Pan head screw M5x16(one piece)
Guide
Protrusion of bearing retainer
Pan head screw
M5x12(one piece)
Magnet sleeve
E ring
Tapping screw CT4 x 16(4 pieces)
(2) Replacing methods of spiral bevel gear 52
1) Disconnect the magic pad.
2) Disconnect the tapping screw CT 4 x 16 for holding the bearing box.
3) The spiral bevel gear 52 is inserted into the spindle through pressing.
Disassemble it as shown on the below figure.
Disassembling Assembling
Use the arbor press to press the spindle edge.