Text preview for : 07_Alignment & Adjustment.pdf part of Samsung 07 Alignment & Adjustment Samsung LCD TV LE46N71B 07_Alignment & Adjustment.pdf
Back to : 07_Alignment & Adjustment | Home
3 Alignments and Adjustments
3 Alignments and Adjustments
3-1 Service Instruction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers, do not allow the marker generator to distort
test result.
5. Connect the TV only to an AC power source with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.
7. To protect aganist shock hazard, use an isolation transform.
3-1
3 Alignments and Adjustments
3-2 How to Access Service Mode
3-2-1 Entering Factory Mode
" "
- If you have Factory remote - control
- The buttons are active in the service mode.
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left
Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -, Menu, TV/VIDEO(Enter)
3-2
3 Alignments and Adjustments
3-3 Factory Data
1. Calibration
2. Option Table XXXX XXXX
3. White Balance
4. SVP-PX
5. Option Block
6. STV8257/STA323W
7. YC Delay
8. Adjust
9. I2C Check
10. W/B MOVIE
11. Checksum
12. Reset
13. Spread Spectrum
T-NMSLMPEA-1006(Main Micom Ver)
T-MSLMPEUS-1000(Sub Micom Ver)
T-MSLMPEUW-1009(MMS Ver)
Month / Day / Year / Hour / Min / Sec
1. Calibration
1) AV Calibration
2) Comp Calibration
3) PC Calibration
4) HDMI Calibration
2. Option Table XXXX XXXX
Inch Option 40" Carrier Mute ON TTX Group Auto
Gamma AMLCD Language English Auto Power ON
Panel Option AMLCD_INT Auto FM ON Magazine LNA OFF
2HDMI ON High Deviation OFF VOL MODE LARGE
Brt.Sensor OFF TTX ON ---- OFF
EnergySave OFF TTX List Flof Debug OFF
LBE/FBE ON ACR OFF Ch.Table SUWON
FRC(Micronas) OFF Dynamic CE OFF iDTV_Cntry UK
FRC 2X ON Dynamic Dimming ON Dynamic Contrast OFF
LNA OFF Tuner TOP 8
3-3
3 Alignments and Adjustments
3. White Balance
No Item Range TV/AV Component PC DVI(HDMI)
1 Sub-Brightness 0~255 80 115 128 140
2 R-offset 0~255 120 130 128 129
3 G-offset 0~255 128 128 128 128
4 B-offset 0~255 113 128 128 128
5 Sub-Contrast 0~63 36 32 32 28
6 R-Gain 0~255 140 129 128 130
7 G-Gain 0~255 128 128 128 128
8 B-Gain 0~255 150 129 128 120
4. SVP-EX
1) Comb Filter
No Item Range EEPROM NTSC PAL SECAM Control IC Remark
1 Y-Filter 0~255 80h X
2) Peaking
No Item Range EEPROM TV AV Component Control IC Remark
1 Y-Peaking 0~255 80h X
2 Peaking Delay 0~255 80h X
3 Peaking Gain 0~255 80h X
4 Peaking Width 0~255 80h X
5 Peaking f0 0~255 80h X
3) NR
No Item Range EEPROM TV/AV/S-Video Component PC Control IC Remark
1 Y-NR-Off 0~255 80h X
2 C-NR-Off 0~255 80h X
3 Y-NR-ON 0~255 80h X
4 C-NR-ON 0~255 80h X
4) Delnterlace
No Item Range EEPROM TV/AV/S-Video Component PC Control IC Remark
1 Monitor 0~255 80h X
3-4
3 Alignments and Adjustments
5) Picture Gain Adjust
No Item Range EEPROM TV/AV/S-Video Component PC DVI/HDMI
1 TCD3 Contrast 0~255 AV Calibration(78h) 78h 78h 78h
2 TCD3 Brightness 0~255 AV Calibration(20h) 20h 20h 20h
3 TCD3 CR Saturation 0~255 78h 78h 78h 78h
4 TCD3 CB Saturation 0~255 78h 78h 78h 78h
5 TCD3 YC Delay 0~15 00h 00h 00h 00h
6 Analog Y offset 00~255 40h 3 40h 40h
7 Analog PB offset 00~255 80h DTV Calibration(80h) 80h 80h
8 Analog PR offset 00~255 80h DTV Calibration(80h) 80h 80h
9 Analog Y Gain 00~255 D6h DTV Calibration(D6h) D6h D6h
10 Analog PB Gain 00~255 FEh FEh FEh FEh
11 Analog PR Gain 00~255 FEh FEh FEh FEh
12 Black Level Setting 00~255 00h
13 Brightness (SVP) 0~255 00h
5. MST9883
No Item Range EEPROM TV/AV/S-Video Component PC DVI/HDMI
1 R-offset 00~255 151 (SC1 RGB) PC Calibration(128)
2 G-offset 00~255 151 (SC1 RGB) PC Calibration(128)
3 B-offset 00~255 151 (SC1 RGB) X PC Calibration(128) X
4 R-Gain 00~255 123 (SC1 RGB) PC Calibration(192)
5 G-Gain 00~255 123 (SC1 RGB) PC Calibration(192)
6 B-Gain 00~255 123 (SC1 RGB) PC Calibration(192)
6. MSP34XX/44XX
No Item Range EEPROM PAL
1 FM-Prescale 00~255 20h
2 NT-M-Prescale 00~255 20h
3 SECAM-L-Prescale 00~255 22h
4 NICAM-Prescale 00~255 42h
5 AV-Prescale 00~255 1Ah
6 12S_1 Prescale 00~255 10h
7 12S_12 Prescale 00~255 10h
8 Carrier Mute 00~255 42h
9 Pilot High 00~255 14
10 Pilot Low 00~255 7
3-5
3 Alignments and Adjustments
7. YC Delay
No Item Range EEPROM TV/AV/S-Video Component PC DVI/HDMI
1 RF PAL-B/G 00~255 77h
2 RF PAL-D/K 00~255 88h
3 PF PAL-I 00~255 66h
4 RF SECAM-B/G 00~255 88h
5 PF SECAM-D/K 00~255 77h
6 RF SECAM-L/L' 00~255 88h
7 RF NTSC 3.58 00~255 66h 88h 88h 88h
8 RF NTSC 4.43 00~255 CCh
9 AV PAL 00~255 77h
10 AV SECAM 00~255 BBh
11 AV NTSC 3.58 00~255 66h
12 AV NTSC 4.43 00~255 CCh
13 AV PAL60 00~255 77h
8. Adjust
No Item Range EEPROM TV/AV/S-Video Component PC DVI/HDMI Control IC Remark
1 Video Mute Time 10
2 Melody Volume 0~20 5
Ana_Dimm_Max FEH
3 TTX Contrast 0~100 50
4 TTX Brightness 0~100 50
5 TTX Color 0~100 50
6 Dynamic Contrast 0~100 100
7 Dynamic Brightness 0~100 50 Dynamic
8 Dynamic Color 0~100 55 Mode
9 Dynamic Sharpness 0~100 75
10 Standard Contrast 0~100 80
11 Standard Brightness 0~100 50 Standard
12 Standard Color 0~100 50 Mode
13 Standard Sharpness 0~100 50
14 Movie Contrast 0~100 70
15 Movie Brightness 0~100 50 Movie
16 Movie Color 0~100 25 Mode
17 Movie Sharpness 0~100 45
No Item Range EEPROM TV/AV/S-Video Component/PC/HDMI
1 LNA PLUS
2 RFDB_1 Level 1
3 RFDB_2 Level 5 X P4 CVD2 0x7F
4 RFDB_3 Level 10 [07..00]
5 RFDB_4 Level 16
3-6
3 Alignments and Adjustments
9. 12C Check
10. Chip Debugger : OFF
11. Checksum XXXX XXXX
12. Reset
13. Spread Spectrum
1 Spectrum ON
2 Delta -3
3 Positive 8
4 Negative 2
3-7
3 Alignments and Adjustments
3-4 Service Adjustment
3-4-1 White Balance - Calibration
If picture color is wrong, do calibration first.
Equipment : CA210, Patten : chess pattern
Execute calibration in Factory Mode
Source AV : PAL composite, Component : 1280*720/60Hz
PC : 1024*768/60Hz
( chess patten )
3-4-2 White Balance - Adjustment
If picture color is wrong, check White Balance condition.
Equipment : CA210, Patten : Toshiba
Adjust W/B in Factory Mode
Sub brightness and R/G/B Offset controls low light region
Sub contrast and R/G/B Gain controls high light region
Source AV : PAL composite, Component : 1280*720/60Hz
HDMI[DVI] : 1280*720/60Hz
[ Test Pattern : MSPG-945 Series Pattern #16 ]
*Color temperature
1500K +/-500, -6 ~-20 MPCD
*Color coordinate
H/L : 267/263 +/- 2 35.0 Ft +/- 2.0Ft
L/L : 270/260 +/- 3 1.5 Ft +/- 0.2Ft
Toshiba Patten
3-8
3 Alignments and Adjustments
3-4-3 Conditions for Measurement
1. On the basis of toshiba ABL pattern : High Light level (57 IRE)
- INPUT SIGNAL GENERATOR : MSPG-925LTH
* Mode NO 2 : 744X484@60 Hz
NO 6 : 1280X720@60 Hz
NO 21 : 1024X768@60 Hz
* Pattern NO 36 : 16 Color Pattern
NO 16 : Toshiba ABL Pattern
2. Optical measuring device : CA210 (FL)
Please use the MSPG-925 LTH generator for model LE26M51B/LE32M51B/LE40M51B/LE46M51B.
3-4-4 Method of Adjustment
1. Adjust the white balance of AV, Component and DVI Modes.
(AV Component)
a) Set the input to the mode in which the adjustment will be made
(RF DTV PC DVI).
* Input signal - VIDEO Mode : Model #2 (744*484 Mode), Pattern #16
- DTV,DVI Mode : Model #6 (1280*720 Mode), Pattern #16
- HDMI Mode: Model #6(1280*720 Mode), Pattern #16
b) Enter factory color control, confirm the data.
c) Adjust the low light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust sub - Brightness to set the 'Y' value.
- Adjust red offset ('x') and blue offset ('y') to the color coordinates.
Picture 4-2 Toshiba ABL Pattern
Low light
Measurement point
* Do not adjust green offset data.
d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
3-9
3 Alignments and Adjustments
d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
Picture 4-3 Toshiba ABL Pattern
High light
Measurement point
3-10
3 Alignments and Adjustments
3-5 Software Upgrade
3-5-1 How to Update Flash ROM
1. Installthe Flash Downloader
ConnectSet(Service Jack)and Jig Cable to execute Program Update.
2. Flash Downloader program update
-Before Turning on the set,Click "connect"which is under of OSD Screen!
-Turn on the Set.
3-11
3 Alignments and Adjustments
Memo
3-12