Text preview for : Pioneer_GM-7100M.pdf part of Pioneer GM-7100M Pioneer GM GM-7100M Pioneer_GM-7100M.pdf
Back to : Pioneer_GM-7100M.pdf | Home
Service
Manual GM-7100M/XU/EW
ORDER NO.
CRT3371
MONO POWER AMPLIFIER
GM-7100M
GM-7100M /XU/UC
/XU/EW
GM-7100M /XU/ES
GM-7100M /XU/CN
GM-7150M /XU/UC
For details, refer to "Important check points for good servicing".
PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.
PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936
C PIONEER CORPORATION 2004 K-ZZB. DEC. 2004 Printed in Japan
1 2 3 4
A SAFETY INFORMATION
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
B WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
- Service Precaution
You should conform to the regulations governing the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
C
D
E
F
2 GM-7100M/XU/EW
1 2 3 4
5 6 7 8
[Important Check Points for Good Servicing] A
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as B
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state. C
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure D
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
3. Lubricants, Glues, and Replacement parts E
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual. F
GM-7100M/XU/EW 3
5 6 7 8
1 2 3 4
A CONTENTS
SAFETY INFORMATION............................................2 5. ELECTRICAL PARTS LIST........................................25
1. SPECIFICATIONS .......................................................5 6. ADJUSTMENT .........................................................28
2. EXPLODED VIEWS AND PARTS LIST ......................6 7. GENERAL INFORMATION.......................................29
2.1 PACKING..............................................................6 7.1 DIAGNOSIS .......................................................29
2.2 EXTERIOR ............................................................8 7.1.1 DISASSEMBLY.........................................29
3. SCHEMATIC DIAGRAM...........................................12 7.1.2 CONNECTOR FUNCTION DESCRIPTION ......31
3.1 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) ....12 8. OPERATIONS ...........................................................32
3.2 REMOTE CONTROL UNIT ................................18
B 4. PCB CONNECTION DIAGRAM................................20
4.1 AMP UNIT..........................................................20
4.2 REMOTE CONTROL UNIT ................................24
C
D
E
F
4 GM-7100M/XU/EW
1 2 3 4
5 6 7 8
1. SPECIFICATIONS A
Power source .......................................................................................................... 14.4 V DC (10.8 -- 15.1 V allowable)
Grounding system .......................................................................................................................................... Negative type
Current consumption .................................................................................................... 33.0 A (at continuous power, 4 )
Backup current .................................................................................................................................................. 3 mA or less
Average current drawn* .......................................................................................................... 9.0 A (4 for one channel)
16.0 A (2 for one channel)
Fuse ........................................................................................................................................................................ 30 A