Text preview for : DC1470-TE.pdf part of MAKITA DC1470-TE MAKITA DC1470-TE.pdf
Back to : DC1470-TE.pdf | Home
T ECHNICAL INFORMATION
Models No. DC1470
NEW TOOL
P1/2
Description Charger
CONCEPTION AND MAIN APPLICATIONS
This charger can charge 1.3Ah Ni-Cd.batteries of 7.2V - 14.4V approx
in 60 minutes.
Its brief benefits and features are as follows. H
* The charging time is kept in the steady level by controlling the
out put current ( current for charging battery) in spite of the changeable
input voltage (power source voltage).
* The charger can switch into trickle charge (maintenance charge) mode
W
to keep the full charged condition for battery left in the charger.
L
The end of charging process is recognized by thermostat.
The Ni-Cd.batteries with high capacity (over 1.7Ah) and all of
Ni-MH. batteries can not be charged with this charger.
Dimensions : mm ( " )
Width ( W ) 80 (3-1/8)
Height ( H ) 63 (2-1/2)
Length ( L ) 145 (5-3/4)
Specification
Continuous Rating (W)
Voltage (V) Current (A) Cycle (Hz) Max. Output(W)
Input Output
110 - 120 50 - 60 40
120 50 - 60 40
220 50 - 60 40
220 - 240 50 - 60 40
230 - 240 50 - 60 40
Output voltage (D/C) 7.2 V, 9.6 V, 12 V, 14.4 V The chargeable batteries
Output current (D/C) 1.5 A Voltage Type No.
Charging time Approx. 60 min. 7.2 V 7000
Net weight : Kg ( lbs ) 0.41 (0.9) 9000
9.6 V 9100
Cord length : m ( ft ) 2.0 (6.6)
9120
1210
12 V 1220
1200
1200A
14.4 V 1420
Repair P2/2
<1> The circuit board can not be repaired, because the circuit itself are molded on the board
with the urethane resin.
It has to be replaced completely with new one.
<2> In case of damaged varistor or fuse, they can be repaired according to the following procedure without
replacing the circuit board.
(1) How to find broken varistor
a. In case that the surface of varistor (ref. to the following illustration) has broken or has become black, and
fuse has been cut, the varistor has been damaged.
b. Varistor can be damaged easily, if the charger is plugged in a double voltage of the rating one.
c. It is considered that the varistor has been broken for other reasons, if the fuse is broken while the surface
of varistor is not damaged. In this case circuit board has to be replaced.
Varistor
Circuit board
Charger case set
Fuse
Fig.1
(2) Replacing damaged varistor
a. Varistor is assembled on circuit board with solder. Remove it from circuit board
with soldering iron.
Varistor Circuit board
Fig.2
When removing varistor, melt this part with soldering iron
and remove varistor.
b. Assemble new varistor to the circuit board by soldering.
c. Cut the surplus of varistor's wire with nipper.
Circuit board Varistor
Less than 3mm
Fig.3
(3) Replacing damaged fuse
a. Fuse is assembled on circuit board with solder. Remove it from circuit board with soldering iron.
b. Assemble new fuse to the circuit board by soldering.
c. Cut the surplus of fuse's wire with nipper.
Fuse Fig.4
Less than 3mm
When removing fuse, melt this part with soldering iron
and remove fuse.